Kawasaki KX450F 2013 is a competition model motorcycle designed for participation in sanctioned competition events upon a closed course. It features a powerful engine and advanced suspension system for optimal performance in racing and sporting use. Its lightweight and high-performance design provide superb handling and stability, making it a formidable choice for experienced riders.
advertisement
MAINTENANCE AND ADJUSTMENT
33
Periodic Maintenance Chart
The maintenance and adjustments outlined in this chapter are easily carried out and must be done in accordance with the Periodic Maintenance Chart to keep the motorcycle in good running condition.
1. Periodic Inspection (Engine Related Item)
FREQUENCY
OPERATION
Throttle cable - inspect and adjust
After each race (or
2.5 hours)
•
Valve clearance - inspect †
Clutch plates - inspect †
Spark plug - clean and inspect †
Clutch - inspect
Air cleaner element - clean †
Throttle body assy - inspect and adjust
•
•
•
•
•
K Cylinder head, cylinder - inspect
K Crankshaft - inspect
Every 3 races (or
7.5 hours)
Every 6 races (or
15 hours)
•
•
•
Every 12 races (or
30 hours)
As required
See
Page
60
81
75
47
71
56
61
–
–
Muffler - clean and inspect †
Kick pedal and shift pedal - clean
Engine sprocket - inspect †
•
•
•
87
–
96 j
j
34
FREQUENCY
OPERATION
Coolant level - inspect
Breather hose - inspect
Water hoses and connections - inspect †
After each race (or
2.5 hours)
•
•
•
Every 3 races (or
7.5 hours)
Every 6 races (or
15 hours)
Every 12 races (or
30 hours)
As required
See
Page
43
–
43
35
2. Periodic Inspection (Chassis Related Item)
OPERATION
Brake - adjust †
Brake pad wear - inspect †
Brake fluid level - inspect †
Spoke tightness and rim runout - inspect
†
Drive chain - lubricate
K Fuel system - clean
FREQUENCY
Drive chain - inspect and adjust
Drive chain wear - inspect †
Front fork - clean and inspect
Nuts, bolts, fasteners - inspect †
After each race (or
2.5 hours)
•
•
•
•
•
•
•
•
•
Fuel hose, connections - inspect †
Brake hoses, connections - inspect †
Steering play - inspect †
•
•
•
K Steering stem bearing - lubricate
Rear sprocket - inspect †
General lubrication - perform
K Wheel bearing - inspect †
•
•
•
Every 3 races (or
7.5 hours)
Every 6 races (or
15 hours)
Every 12 races (or
30 hours)
As required
•
•
See
Page
101
104
102
143
145
145
105
–
96
152
–
91
97
94
107
146
– j
j
36
OPERATION
K
K
FREQUENCY After each race (or
2.5 hours)
Swingarm and UNI-TRAK linkage pivots
- inspect †
Swingarm and UNI-TRAK linkage pivots
- lubricate
Frame - inspect
Wheels/tires - inspect
Rear shock absorber - inspect
Cable - inspect
•
•
•
•
Every 3 races (or
7.5 hours)
•
•
Every 6 races (or
15 hours)
Every 12 races (or
30 hours)
As required
See
Page
–
–
–
142
136
–
37
3. Periodic Replacement (Engine and Chassis Related Item)
OPERATION
FREQUENCY After each race (or
2.5 hours)
Every 3 races (or
7.5 hours)
Engine oil - change
Oil filter - replace
K Piston and piston ring - replace
K Piston pin - replace
Silencer wool - replace
Spark plug - replace
K Brake fluid - change
K
Brake master cylinder cup and dust cover replace
K Brake caliper fluid seal and dust seal - replace
K Brake hoses - replace
Front fork oil - change
K Fuel hose - replace
K Rear shock absorber oil - change
•
•
Every 2 years
Every 2 years
Every 6 races (or
15 hours)
•
•
•
Every 2 years
Every 4 years
•
Every 5 years
•
†: Replace, add, adjust, clean or torque if necessary.
K : Should be serviced by referring to the Service Manual or an authorized Kawasaki dealer.
Every 12 races (or
30 hours)
See
Page
39
39
–
•
–
87
47
–
–
–
–
112
–
– j
j
38
Engine Oil
In order for the engine, transmission and clutch to function properly, maintain the engine oil at the proper level, and change the oil and oil filter periodically.
Not only do dirt and metal particles collect in the oil, but the oil itself loses its lubricative quality if used too long.
WARNING
Motorcycle operation with insufficient, deteriorated, or contaminated engine oil will cause accelerated wear and may result in engine or transmission seizure, accident, and injury. Check the oil level before each ride and change the oil according to the periodic maintenance chart in the Owner’s Manual.
Because of the semi-dry sump lubrication system, the engine oil level indicated on the oil level inspection window will fluctuate depending on the motorcycle’s position and engine speed when the engine’s shut off. To ensure a proper reading of the engine oil level, follow the Oil Level Inspection procedures closely.
NOTICE
Racing the engine before the oil reaches every part can cause engine seizure.
Oil Level Inspection
•
If the oil has just been changed, let the motorcycle sit a few minutes allowing the oil to settle.
•
Start the engine and run it for several minutes at idle speed. Do not run the engine at high engine speed.
•
Stop the engine and wait several minutes for the oil to settle.
•
Check the engine oil level with the motorcycle vertical through the oil level inspection window on the lower right side of the engine. The oil level should come up between the high and low level lines next to the oil level inspection window.
NOTE
○
If the oil level is too high, remove the excess oil using a syringe or other suitable device.
○
If the oil level is too low, add the correct amount of oil through the oil filler opening. Use oil of the same type and brand as those of the one that is already in the engine.
NOTE
○
If no oil appears in the oil level inspection window, tip the motorcycle slightly to the right until oil is visible then return to an upright position. If no oil appears even when tipped at an extreme angle, remove the drain bolts to empty any oil that may be in the transmission and crankcase, reinstall the drain bolts and refill with the specified amount of oil.
39
Oil and/or Oil Filter Change
The engine oil and/or oil filter should be changed periodically to ensure long engine life.
•
Warm up the engine thoroughly so that the oil will pick up any sediment and drain easily.
•
•
Stop the engine, and place a container beneath it.
Remove the oil filler plug.
•
Remove the oil drain bolts and position the vehicle perpendicular to the ground to allow all the oil to drain.
j
A. Oil Level Inspection Window
B. High Level Line
C. Low Level Line
D. Oil Filler Plug
A. Drain Bolt (M6)
B. Drain Bolt (M10)
j
40
WARNING
Engine oil is a toxic substance. Dispose of used oil properly. Contact your local authorities for approved disposal methods or possible recycling.
•
When the oil filter is replaced, remove the oil filter cap bolts and take off the cap with O-rings.
•
Be sure to install the spring on the original position.
A. Oil Filter Cap Bolts
B. Oil Filter Cap
A. Spring
•
•
Replace the oil filter element with a new one.
Replace the O-rings with new ones.
•
Apply grease to the grommet.
•
Install the oil filter element with the grommet toward the oil filter cap.
NOTICE
Inside-out installation stop oil flow, causing engine seizure.
•
Install the oil filter cap with the grease applied to the new O-rings and tighten its bolts to the specified torque.
A. Oil Filter Element
B. Grommet
C. O-rings
Tightening Torque
Oil Filter Cap Bolts:
9.8 N·m (1.0 kgf·m, 87 in·lb)
•
After the oil has completely drained out, install the drain bolts with their new gaskets. Proper torque for they are shown in the table.
41
Tightening Torque
Engine Oil Drain Bolt (M10):
20 N·m (2.0 kgf·m, 15 ft·lb)
Engine Oil Drain Bolt (M6):
7.0 N·m (0.71 kgf·m, 62 in·lb)
NOTE
○
Replace the gasket and O-rings with new ones.
•
Fill the engine up to the high level line with good quality engine oil specified in the table.
Recommended Engine Oil
Castrol “Power1 Racing 4T” 5W-40 or
“Kawasaki Performance 4-Stroke Full Synthetic
Oil*” 10W-40 or
“Kawasaki Performance 4-Stroke
Semi-Synthetic Oil*” 10W-40 or
“Kawasaki Performance 4-Stroke Motorcycle
Oil*” 10W-40
*Kawasaki Performance Oils and Lubricants have been specifically engineered for your vehicle. Consistent use of these products meets or exceeds warranty and service requirements and can help to extend the life of your Kawasaki.
Engine Oil Capacity
Capacity:
0.96 L (1.01 US qt) (When filter is not removed)
0.98 L (1.04 US qt) (When filter is removed)
1.20 L (1.27 US qt) (When engine is completely dry) j
j
42
NOTE
○
If unavailable, use equivalent engine oil in accordance with the following table.
Type:
API SG, SH, SJ, SL or SM with JASO MA, MA1 or MA2
Viscosity:
SAE 10W-30, 10W-40, 10W-50
NOTE
○
Do not add any chemical additive to the oil. Oils fulfilling the above requirements are fully formulated and provide adequate lubrication for both the engine and the clutch.
The oil viscosity may need to be changed to accommodate atmospheric conditions in your riding area.
•
Tighten the oil filler plug.
Tightening Torque
Oil Filler Plug:
3.5 N·m (0.36 kgf·m, 31 in·lb)
•
Start the engine.
•
Check the oil level and oil leakage.
Cooling System
Water Hoses
Check the water hoses for cracks or deterioration, and the connections for looseness in accordance with the Periodic Maintenance Chart.
Radiator
Check the radiator fins for obstruction by insects or mud. Clean off any obstructions with a low-pressure stream of water.
NOTICE
Using high-pressure water, as from a car wash facility, could damage the radiator fins and impair the radiator’s effectiveness.
Do not obstruct or deflect airflow by installing unauthorized accessories in front of the radiator.
Interference with the cooling airflow can lead to overheating and consequent engine damage.
Coolant
Coolant absorbs excessive heat from the engine and transfers it to the air through the radiator. If the coolant level becomes low, the engine overheats and may suffer severe damage. Check the coolant level each day before riding the motorcycle, and replenish coolant if the level is low.
43
WARNING
The cooling system can get extremely hot during normal operation and cause serious burns. Do not touch the radiator when it is hot, nor open the radiator cap. Hot coolant inside will cause severe burns.
NOTE
○
The coolant originally filled into the cooling system contains 50% of a permanent, ethylene-glycol
-based antifreeze, has a freezing point of –35°C
(–31°F) and a green appearance.
Coolant Level Inspection
•
Situate the motorcycle perpendicular to the ground until the radiator cap is level to the ground, so that the radiator cap is located uppermost in order to exhaust the air accumulated in the radiator.
•
Remove the radiator cap in two steps.
•
First, turn the cap counterclockwise to the first stop and wait there for a few seconds.
j
j
44
•
Then, push and turn the cap further in the same direction and remove it.
A. Radiator Cap
•
Check the coolant level in the radiator.
The coolant should come up to the bottom of the radiator filler neck.
NOTE
○
Check the coolant level when the engine is cold
(room or ambient temperature).
A. Coolant Level
B. Filler Neck
•
If the coolant level is low, add coolant through the radiator filler opening to the bottom of the filler neck.
Water and Antifreeze Mixing Ratio
1:1 (water:antifreeze)
Recommended Antifreeze
Permanent type of antifreeze (ethylene glycol plus corrosion and rust inhibitor chemicals for aluminum engines and radiators)
Coolant Total Amount
1.1 L (1.2 US qt)
•
Install the radiator cap.
Coolant Change
The coolant should be changed to ensure long engine life, if necessary.
•
Wait for the engine to cool completely.
•
Situate the motorcycle perpendicular to the ground until the radiator cap is level to the ground.
•
Remove the radiator cap in two steps.
•
Drain the coolant from the engine and radiator in the following way.
•
Place a container under the coolant drain bolt on the water pump cover and remove the drain bolt.
A. Coolant Drain Bolt
B. Water Pump Cover
45
NOTICE
Immediately wash away any coolant that spills on the frame, engine, or wheel.
WARNING
Coolant on tires will make them slippery and can cause loss of traction resulting in an accident and injury. Thoroughly clean any coolant that might have splashed on the tires.
•
Visually inspect the old coolant.
•
If whitish cotton-like wafts are observed, aluminum parts in the cooling system are corroded and the system must be flushed.
•
If the coolant is brown, iron or steel parts are rusting and the system must be flushed.
•
Check the cooling system for damage, loose connections, and leaks.
•
Install the coolant drain bolt with its new gasket at the water pump cover and apply the specified torque.
NOTE
○
Always replace a gasket with a new one.
Tightening Torque
Coolant Drain Bolt:
7.0 N·m (0.71 kgf·m, 62 in·lb) j
j
46
•
Fill the radiator up to the bottom of the radiator filler neck with coolant.
•
Lean the motorcycle slightly until the radiator filler neck is level to the ground so that the filler neck is located uppermost in order to exhaust the air accumulated in the radiator.
NOTICE
Use coolant containing corrosion inhibitors made specifically for aluminum engines and radiators in accordance with the instruction of the manufacture. Soft or distilled water must be used with the antifreeze in the cooling system. If hard water is used in the system, it causes scale accumulation in the water passages, and considerably reduces the efficiency of the cooling system.
NOTE
○
Pour in the coolant slowly so that it can expel the air from the engine and radiator.
•
•
Install the radiator cap.
Check the cooling system for leaks.
•
Start the engine and warm up thoroughly, then stop it.
•
Check the coolant level after the engine has cooled down. The coolant should come up to the bottom of the radiator filler neck.
•
If the coolant level is low, add coolant up to the bottom of the radiator filler neck.
•
Install the radiator cap.
•
Check the cooling system for leaks.
Spark Plug
The spark plug should be taken out periodically for inspection and regapping. Measure the gap with a wire-type thickness gauge. If incorrect, adjust the gap to the specified value by bending the outer electrode.
Spark Plug Gap
CPR8EB-9
CPR9EB-9
0.8
∼ 0.9 mm (0.03
∼ 0.04 in.)
47
If the plug is oily or has carbon built up on it, clean it. The plug may also be cleaned using a high flash
-point solvent and a nonmetal brush (nylon etc.). If the spark plug electrodes are corroded, or damaged, or if the insulator is cracked, replace the plug. The standard spark plug is shown in the table below.
Standard Spark Plug
NGK CPR8EB-9
To find out whether the plug’s heat range is correct, remove the plug and examine the ceramic insulator around the center electrode. If the ceramic is light brown, the spark plug correctly matches the engine temperature.
If the ceramic is burned white, the plug should be replaced with a colder plug.
Optional Spark Plug
Colder NGK CPR9EB-9
NOTE
○
If the engine performance drops, try replacing the spark plug to regain performance.
A. Gap
B. Outer Electrode j
j
48
•
Spark Plug Removal and Installation
Remove the seat (see Air Cleaner section).
•
Remove the bolts and take off the radiator shroud on both sides.
•
Remove the fuel tank mounting bolt and band.
A. Fuel Tank Mounting Bolt
B. Band
A. Bolts
B. Radiator Shroud
•
Be sure to place a piece of cloth around the fuel hose joint.
•
Wipe off the dirt of the surface around the connection using a cloth or a soft brush.
•
Insert a thin blade screwdriver into the slit on the joint lock.
49
WARNING
Fuel is flammable and explosive under certain conditions and can cause severe burns.
Be prepared for fuel spillage; any spilled fuel must be completely wiped up immediately. When the fuel hose is disconnected, fuel spills out from the hose and the pipe because of residual pressure.
Cover the hose connection with a piece of clean cloth to prevent fuel spillage.
•
Turn the driver to disconnect the joint lock.
•
Disconnect the fuel hose joint from the outlet pipe.
j
A. Cloth
B. Thin Blade Screwdriver
C. Joint Lock
A. Turn
B. Joint Lock
C. Fuel Hose Joint
j
50
•
Cover the pipe and the fuel hose joint with the vinyl bags to keep them clean.
•
Disconnect the fuel pump lead connector.
•
Remove the fuel tank.
•
Clean the cylinder head cover around the spark plug cap hole before removing the spark plug.
•
Pull the spark plug cap off the plug before removing the spark plug.
A. Fuel Pump Lead Connector
WARNING
Gasoline is extremely flammable and can be explosive under certain conditions.
Always stop the engine and do not smoke.
Make sure the area is well-ventilated and free from any source of flame or sparks; this includes any appliance with a pilot light.
A. Spark Plug Cap
•
Loosen and remove the spark plug with a suitable wrench (16 mm, 0.63 in.).
•
When reinstalling the spark plug, torque it to specification.
Tightening Torque
Spark Plug:
13 N·m (1.3 kgf·m, 115 in·lb)
•
Install the spark plug cap so that it is aligned with the line on the cylinder head cover.
•
Pull up the plug cap lightly to make sure of the installation of the spark plug cap.
51
•
Make sure that the dampers are in place on the frame and are not damaged. If the dampers are not fixed completely, reattach them with an adhesive. If the dampers are damaged, replace them with new ones.
j
A. Spark Plug Cap
B. Line A. Dampers
•
Check the joint lock for deformation and wear.
•
If the joint lock is deformed, replace the fuel hose with a new one.
•
Apply engine oil to the fuel outlet pipe lightly.
j
52
•
Insert the fuel hose joint straight onto the fuel outlet pipe until the hose joint clicks.
•
Push the joint lock until the hose joint clicks.
•
Push and pull the fuel hose joint back and forth more than two times, and make sure it is locked and does not come off.
A. Fuel Hose Joint
B. Joint Lock
NOTICE
When installing the fuel hose joint, do not apply strong force to the outlet pipe on the fuel pump. The pipe made from resin could be damaged.
A. Fuel Hose Joint
B. Push and Pull
WARNING
Leaking fuel can cause a fire or explosion resulting in serious burns. Make sure the hose joint is installed correctly on the delivery pipe by sliding the joint.
NOTE
○
If it comes off, reinstall the fuel hose joint.
•
Run the fuel pump lead over the fuel hose.
•
Before installing the fuel tank, check that both throttle cables run over the main harness.
NOTE
○
To prevent the bottom of the fuel tank from pushing the throttle cables, run the throttle cables over the main harness correctly.
•
•
Hook the band to the fuel tank.
Tighten the fuel tank mounting bolt.
•
After installing the fuel tank, make sure that both throttle cables (outer) move slightly by pulling them back and forth in the upper space of the right side of the fuel tank. Check that both throttle cables run under the frame (right side) as shown in the figure.
53
•
Temporarily tighten the radiator shroud bolts following the tightening sequence.
•
Tighten the radiator shroud bolts.
Tightening Torque
Radiator Shroud Bolts:
9.8 N·m (1.0 kgf·m, 87 in·lb)
•
Install the removed parts.
NOTE
○
Insert the fuel tank breather hose outlet end into the steering stem hole.
A. Throttle Cables
B. Fuel Tank
C. Bottom of the Frame (Right Side) j
j
54
Air Cleaner
A clogged air cleaner restricts the air intake, increases fuel consumption, reduces engine power, and can cause spark plug fouling. Inspect the air intake system, which includes the air filter and air duct to the throttle body assy, and the duct clamps and throttle body assy, before each race or practice session.
WARNING
If dirt or dust is allowed to pass through into the throttle body assembly, the throttle may become stuck, possibly causing accident.
Be sure to keep the dust from entering during cleaning.
NOTICE
A clogged air cleaner will affect fuel mixture to the engine and reduce engine power and cause spark plug fouling.
NOTE
○
In dusty areas, the element should be cleaned more frequently than recommended interval.
○
After riding through rain or on muddy roads, the element should be cleaned immediately.
Element Removal and Inspection
•
Remove the bolts on the both sides.
A. Bolt
•
Open the both side covers slightly outward and slide the seat rearward.
55
•
Remove the wing bolt, and take out the air cleaner element.
j
A. Side Covers
B. Seat
A. Wing Bolt
B. Air Cleaner Element
•
Check inside of the intake tract and throttle body assy for dirt. If dirty, clean the intake tract and throttle body assy thoroughly.
•
Stuff a clean, lint-free towel into the throttle body assy to keep dirt from entering the throttle body assy.
•
Wipe out the inside of the air cleaner housing with a clean, damp towel.
•
Take the element off its frame.
NOTICE
Do not twist or wring the element, as it gets easily torn or damaged.
j
56
•
Inspect the element. If it is dirty, clean it. Also check if the element is in good condition (no tears, hardening or shrinkage). If damaged, replace the element or it will allow dirt into the throttle body assy.
WARNING
A clogged air cleaner may allow dirt and dust to enter the throttle body assembly and the throttle may stick resulting in a hazardous operating condition. Clean the air cleaner according to the periodic maintenance chart; more often if the motorcycle is used in extremely dusty conditions.
NOTICE
A clogged air cleaner may allow dirt and dust to enter the engine, causing it to wear excessively or to become damaged.
A. Air Cleaner Element
B. Element Frame
Element Cleaning and Installation
•
Clean the element in a bath of a high flash-point solvent or hot soapy water. Rinse the element with clear water to remove all traces of the cleaning solution.
•
Squeeze the element dry in a clean towel.
NOTICE
Do not twist, wring or blow the element dry to avoid damaging it.
57
WARNING
Gasoline and low flash-point solvents can be flammable and/or explosive and cause severe burns.
Clean the element in a well-ventilated area, and take care that there is no spark or flame anywhere near the working areas. Do not use gasoline or low flash-point solvents to clean the element.
•
After cleaning, let the filter dry completely. Saturate the element with a high-quality foam air filter oil and make sure that the oil is evenly applied throughout the element. Squeeze out the excess oil, but do not wring the element as this could cause tearing. In this case, too much oil is better than too little. Finally pat the inside of the element with a paper towel to remove any excess oil.
•
Before installation, check the element for damage such as tears, hardening, or shrinkage. If damaged, replace the element.
•
Apply grease to all mating surfaces and to the screw hole in the air cleaner housing and intake tract.
•
Remove the towel from the throttle body assy.
•
Install the element onto its frame, and coat the element lip and lip seat with a thick layer of all
-purpose grease to assure a complete seal.
j
j
58
•
Install the air cleaner element so that its tab faces upward and its projections align with the holes in the housing.
A. Apply grease.
A. Tab
B. Projections
C. Holes
•
Tighten the wing bolt.
•
Insert the hooks of the seat under the flange collar and brackets.
59
•
Install the tabs of the side covers into the inside of the seat, and tighten the bolts.
j
A. Hooks
B. Seat
C. Flange Collar
D. Brackets
A. Tabs
B. Seat
•
Pull up the rear end of the seat to make sure it is securely installed.
j
60
Throttle Cable
Throttle Cable Adjustment
Inspect the throttle grip for smooth operation in all steering positions. Check and adjust the throttle cable in accordance with the Periodic Maintenance
Chart.
•
Check that the throttle grip has 2 ∼ 3 mm (0.08
∼
0.12 in.) of play and turns smoothly.
A. Throttle Grip
B. 2 ∼ 3 mm (0.08
∼ 0.12 in.)
•
If the play is incorrect, loosen the locknut on the upper end of the throttle cable and turn the adjuster to obtain the specified play. Then, tighten the locknut toward the adjuster.
A. Locknut
B. Adjuster
•
With the engine idling, turn the handlebar both ways and check if handlebar movement changes the idle speed. If so, the throttle cable may be improperly adjusted or incorrectly routed, or damaged. Be sure to correct any of these conditions before riding.
WARNING
Operation with improperly adjusted, incorrectly routed, or damaged cables could result in an unsafe riding condition. Be sure the control cables are adjusted and routed correctly, and are free from damage.
Throttle Body Assy
Idle Speed Adjustment
•
Remove the left radiator shroud (see Spark Plug section).
•
Thoroughly warm up the engine.
•
Turn the idle adjusting screw/choke knob to adjust the idle speed 1 950 ∼ 2 050 r/min (rpm) by using the engine revolution tester (The tester should be followed by the method described by the manufacture.).
A. Idle Adjusting Screw/Choke Knob
B. Tester
•
Open and close the throttle a few times to make sure the idle speed does not change, and readjust if necessary.
61
•
With the engine idling, turn the handlebar both ways and check if handlebar movement changes the idle speed. If so, the throttle cable may be improperly adjusted, incorrectly routed, or damaged.
Be sure to correct any of these conditions before riding.
WARNING
Operation with damaged cables could result in an unsafe riding condition. Replace damaged control cables before operation.
NOTICE
This motorcycle’s radiator does not incorporate cooling fan. Prolonged idling of the engine with no airflow through the radiator can cause coolant loss and engine overheating resulting in possible engine damage. Any riding conditions that increase engine temperature will further reduce idling time before coolant loss occurs. These conditions include high ambient temperature, sandy or muddy terrain, or other conditions causing high engine loads at low speeds. Furthermore, warming the engine up excessively before operation, or leaving idling with the hot engine temperature after operation results in the engine overheating, too.
Cleaning the Throttle Body Assy
•
Remove the seat (see Air Cleaner section).
j
j
62
•
Remove the fuel tank (see Spark Plug section).
•
Remove the bolt and take off the side cover on both sides.
•
Loosen the muffler clamp bolt.
•
Remove the muffler mounting bolts, and pull out the muffler body backward.
A. Bolt
B. Side Cover
A. Muffler Clamp Bolt
B. Muffler Mounting Bolts
C. Muffler Body
•
Loosen the air cleaner duct clamp screw.
63
•
Disconnect the intake air temperature sensor connector.
j
A. Air Cleaner Duct Clamp Screw
A. Intake Air Temperature Sensor Connector
j
64
•
Remove the rear frame mounting bolts on the both sides.
•
Pull the rear frame rearward with the air cleaner housing.
•
Disconnect the throttle sensor connector.
•
Disconnect the intake air pressure sensor connector.
•
Disconnect the fuel injector connector.
A. Rear Frame Mounting Bolts
B. Air Cleaner Housing
A. Throttle Sensor Connector
B. Intake Air Pressure Sensor Connector
C. Fuel Injector Connector
•
Be sure to place a piece of cloth around the fuel hose joint.
•
Wipe off the dirt of the surface around the connection using a cloth or a soft brush.
•
Insert a thin blade screwdriver into the slit on the joint lock.
65
•
Turn the driver to disconnect the joint lock.
•
Disconnect the fuel hose joint from the delivery pipe.
j
A. Cloth
B. Thin Blade Screwdriver
C. Joint Lock
A. Turn
B. Joint Lock
C. Fuel Hose Joint
•
Cover the pipe and the fuel hose joint with the vinyl bags to keep them clean.
j
66
•
Loosen the throttle body assy holder clamp screw.
•
Pull the throttle body assy from the holder.
•
Remove the bolts, and take off the throttle pulley cover.
A. Throttle Body Assy Holder Clamp Screw A. Throttle Pulley Cover Bolts
B. Throttle Pulley Cover
•
Loosen the decelerator cable bolt locknut, and free the tip of cable lower end.
•
Loosen the accelerator cable bolt, and free the tip of cable lower end.
67
•
If any carbon accumulates, wipe the carbon off the throttle bore and the throttle valve, using a lint-free cloth penerated with a high flash-point solvent.
j
A. Decelerator Cable Bolt Locknut
B. Accelerator Cable Bolt
C. Tips of Throttle Cable Lower Ends
D. Throttle Pulley
E. Accelerator Cable
F. Decelerator Cable
NOTICE
Never drop the throttle body assy especially on a hard surface. Such a shock to the body assy can damage it.
•
After removing the throttle body assy, cover the throttle body assy holder and air cleaner duct with a clean cloth to protect them from dirt.
•
Clean the throttle body assy.
•
Check the throttle bore at the throttle valve for carbon deposits by opening the throttle valve.
A. Throttle Bore
NOTICE
If dirt gets through into the engine, excessive engine wear and possibly engine damage will occur.
•
Lubricate the lower ends of the throttle cables.
•
Install the tip of accelerator cable lower end to the throttle pulley.
•
Install the accelerator cable so that the position of the claw of the washer is as shown.
•
Install the tip of decelerator cable lower end to the throttle pulley.
j
68
•
While holding the decelerator cable bolt, tighten the cable bolt locknut.
Tightening Torque
Throttle Cable Mounting Bolts:
3.0 N·m (0.31 kgf·m, 27 in·lb)
Throttle Pulley Cover Bolts:
3.4 N·m (0.35 kgf·m, 30 in·lb)
WARNING
Operation with improperly adjusted, incorrectly routed, or damaged cables could result in an unsafe riding condition. Be sure the control cables are adjusted and routed correctly, and are free from damage.
•
Install the throttle body assy to the throttle body assy holder. Align the projection with the groove.
•
Check the throttle body assy is installed securely.
A. Accelerator Cable
B. Claw
C. Decelerator Cable Bolt
D. Decelerator Cable Bolt Locknut
A. Groove
B. Projection
•
Check the joint lock for deformation and wear.
•
If the joint lock is deformed, replace the fuel hose with a new one.
•
Apply engine oil to the fuel delivery pipe lightly.
•
Insert the fuel hose joint straight onto the delivery pipe.
•
Check the white paint of the hose in the throttle body assy side.
•
Push the joint lock until the hose joint clicks.
69
•
Push and pull the fuel hose joint back and forth more than two times, and make sure it is locked and does not come off.
j
A. Fuel Hose Joint
B. White Paint
C. Joint Lock
NOTICE
When installing the fuel hose joint, do not apply strong force to the delivery pipe on the throttle body assy. The pipe made from resin could be damaged.
A. Fuel Hose Joint
B. Push and Pull
WARNING
Leaking fuel can cause a fire or explosion resulting in serious burns. Make sure the hose joint is installed correctly on the delivery pipe by sliding the joint.
NOTE
○
If it comes off, reinstall the fuel hose joint.
j
70
•
Connect the intake air pressure sensor connector, fuel injector connector and throttle sensor connector.
•
Install the rear frame with the air cleaner housing to the throttle body assy.
•
Check the duct is installed securely.
•
Check the clamp position as shown in the figure.
A. Intake Air Pressure Sensor Connector
B. Fuel Injector Connector
C. Throttle Sensor Connector
A. Clamp
•
Tighten the air cleaner duct clamp screw securely.
•
Tighten the throttle body assy holder clamp screw to the specified torque.
Tightening Torque
Throttle Body Assy Holder Clamp Screw:
2.0 N·m (0.20 kgf·m, 18 in·lb)
•
Tighten the rear frame mounting bolts to the specified torque.
Tightening Torque
Rear Frame Mounting Bolts:
34 N·m (3.5 kgf·m, 25 ft·lb)
•
•
Install the fuel tank (see Spark Plug section).
Install the muffler (see Exhaust System section).
•
Install the removed parts.
•
Open and close the throttle a few times to make sure the grip operates correctly.
•
Check the throttle cable play and idle speed adjustment.
71
Clutch
Clutch Lever Adjustment
Proper clutch lever free play is 8 ∼ 13 mm (0.3
∼
0.5 in.). Lever play increases with cable stretch and friction plate wear, requiring periodic adjustment.
When the clutch lever free play is out of specification, first try adjusting it at the clutch lever as follows.
•
Turn the adjuster to obtain the proper amount of clutch lever free play.
j
A. Clutch Lever
B. Adjuster
C. 8 ∼ 13 mm (0.3
∼ 0.5 in.)
If the clutch lever free play cannot be adjusted at the clutch lever, make the adjustment further down the cable as follows.
j
72
•
•
Remove the number plate (see Steering section).
Turn the adjuster in all the way.
•
Slide the dust cover back.
•
Loosen the locknut in the middle of the clutch cable, and turn the adjusting nut so that the clutch lever free play is 8 ∼ 13 mm (0.3
∼ 0.5 in.).
•
Tighten the locknut.
WARNING
Too much cable play can prevent clutch disengagement and cause an accident resulting in serious injury or death. When adjusting the clutch or replacing the cable, be sure the upper end of the clutch outer cable is fully seated in its fitting, or it could slip into place later, creating enough cable play to prevent clutch disengagement.
NOTE
○
After the adjustment is made, start the engine and check that the clutch does not slip and that it releases properly.
A. Dust Cover
B. Locknut
C. Adjusting Nut
•
Friction and Steel Plates Removal
Drain the engine oil (see Engine Oil section).
•
Remove the rear master cylinder mounting bolts, brake pedal bolt and the rear brake pedal return spring.
•
Remove the clutch cover bolts.
73 j
A. Rear Master Cylinder Mounting Bolts
B. Brake Pedal Bolt
C. Brake Pedal
D. Return Spring
A. Clutch Cover Bolts
B. Clutch Cover
j
74
•
Remove the clutch cover and gasket.
•
Remove the clutch spring bolts, clutch pressure plate and springs.
•
Remove the adjusting washer, needle bearing, push rod holder and push rod.
A. Clutch Spring Bolts
B. Clutch Pressure Plate
A. Adjusting Washer
B. Needle Bearing
C. Push Rod Holder
D. Push Rod
•
Remove the friction and steel plates.
NOTE
○
The friction plates at each end are different from the plates installed between these plates. However, it is impossible to identify the difference by external view.
○
When servicing the clutch, use a permanent marker to identify the two end friction plates before removing them so that they can be reinstalled in the correct positions.
○
When replacing the friction plates with new ones, mark the two end friction plates just after opening the package so that you can distinguish and install them in the correct location.
•
Remove the clutch hub nut with using the clutch holder (special tool: 57001-1243) to prevent the clutch hub from rotating.
•
Remove the clutch hub.
A. Clutch Hub Nut
B. Clutch Holder (Special Tool: 57001-1243)
C. Clutch Hub
75
Friction and Steel Plates Wear/Damage
Inspection
•
Visually inspect the friction and steel plates to see if they show any signs of seizure, or uneven wear.
If any plates show signs of damage, replace all friction plates and steel plates as a set.
•
Measure the thickness of the friction plates with vernier calipers.
If they have worn past the service limit, replace them with new ones.
Friction Plate Thickness Measurement
Standard 2.92
∼ 3.08 mm (0.115
∼ 0.121 in.)
Service Limit 2.7 mm (0.11 in.)
If the steel plates are replaced, measure the clutch plate assembly length, and use the steel plates in the following table so that the clutch plate assembly length is standard. When measuring the clutch plate assembly length, assemble the clutch plate assembly (clutch hub, friction plates, steel plates, clutch pressure plate, clutch spring bolts, springs).
Tightening Torque
Clutch Spring Bolts:
8.8 N·m (0.90 kgf·m, 78 in·lb) j
j
76
NOTE
○
Do not use the steel plate of 2.0 mm (0.079 in.) and 1.2 mm (0.047 in.) thickness at the same time.
A. Clutch Hub
B. Friction Plates
C. Steel Plates
D. Clutch Pressure Plate
E. Clutch Spring Bolt
F. Spring
G. Standard Length
Clutch Plate Assembly Measurement Standard
Length:
34.9
∼ 35.5 mm (1.37
∼ 1.40 in.)
Steel Plate (Part/No.) Thickness
13089-1095 (Standard) 1.6 mm (0.062 in.)
13089-1005 2.0 mm (0.079 in.)
13089-1010 1.2 mm (0.047 in.)
A. Thickness
B. Friction Plate
Friction and Steel Plate Warp Inspection
•
Place each friction plate and steel plate on a surface plate, and measure the amount of friction plate and steel plate warp with a thickness gauge
(i.e., the gap between the surface plate and each friction plate or steel plate).
•
If any plate is warped over the service limit, replace it with a new one.
Friction and Steel Plate Warp
Friction
Plate
Standard
Maximum 0.15 mm
(0.0059 in.) or less
Service Limit 0.3 mm (0.012 in.)
Steel Plate
Standard
Maximum 0.2 mm
(0.008 in.) or less
Service Limit 0.3 mm (0.012 in.)
77
•
•
Clutch Hub Installation
Install all parts in the reverse order of removal.
•
Replace the clutch hub nut with a new one.
•
Install the clutch hub.
Install the spacer while “OUTSIDE” is faced to the nut.
j
A. Surface Plate
B. Friction or Steel Plate
C. Thickness Gauge
A. Spacer
B. “OUTSIDE”
•
Tighten the clutch hub nut with using the clutch holder (special tool: 57001-1243) to the specified torque.
Tightening Torque
Clutch Hub Nut:
98 N·m (10 kgf·m, 72 ft·lb)
j
78
•
Friction and Steel Plate Installation
Install all parts in the reverse order of removal.
•
Install the friction plates and steel plates, alternating between the two; be sure to start and finish with a friction plate.
•
Apply molybdenum disulfide grease to the push rod as shown in the figure.
•
Install the push rod so that the oil passage hole faces engine right side.
A. Friction and Steel Plates
NOTICE
If dry steel plates and friction plates are installed, apply engine oil to the surfaces of each plate to avoid clutch plate seizure.
A. Apply molybdenum disulfide grease.
B. Oil Passage Hole
•
Apply molybdenum disulfide grease to the contact area of the push rod holder, both surface of the needle bearing and adjusting washer.
•
Install the push rod, push rod holder, needle bearing and adjusting washer.
NOTE
○
Do not close the oil passage hole on the push rod with the molybdenum disulfide grease.
79
Tightening Torque
Clutch Spring Bolts:
8.8 N·m (0.90 kgf·m, 78 in·lb)
•
Check the release shaft lever position by measuring the position distance between the lever and the cable bracket while pushing the release shaft lever lightly forward.
j
A. Apply molybdenum disulfide grease.
B. Push Rod
C. Push Rod Holder
D. Needle Bearing
E. Adjusting Washer
•
Install the clutch pressure plate and springs.
•
Tighten the clutch spring bolts to the specified torque.
A. Release Shaft Lever
B. Push forward
C. Position Distance
D. Cable Bracket
Position Distance
Standard 68.6
∼ 76.4 mm (2.70
∼ 3.01 in.)
j
80
•
If the lever position is not within the standard, select the correct thickness of adjusting washer according to the following table.
•
Remove the clutch pressure plate as necessary and reinstall the clutch and install the selected adjusting washer.
A. Adjusting Washer
B. Needle Bearing
C. Push Rod Holder
Adjusting Washer
Thickness
1.5 mm (0.06 in.)
1.0 mm (0.04 in.)
Part No.
92200-1548
92200-0045
Release Shaft Lever Position and Adjusting
Washer Selection
Position
Distance
Judgment
Washers
Thickness
Quantity
68.6
∼ 76.4 mm
(2.70
∼ 3.01 in.) Standard
More than 76.4
mm (3.01 in.)
Too big
1.5 mm
(0.06 in.)
1.0 mm
(0.04 in.)
1
1
Less than 68.6
mm (2.70 in.)
Too small
1.0 mm
(0.04 in.)
2
•
Place a new clutch cover gasket in position with a thin layer of grease and tighten the bolts.
Tightening Torque
Clutch Cover Bolts:
9.8 N·m (1.0 kgf·m, 87 in·lb)
•
Replace the O-rings on the brake pedal bolt with new ones and install them.
•
When installing the brake pedal, apply the grease to the contact area of the brake pedal pivot and apply a non-permanent locking agent to the threads of the brake pedal bolt.
Tightening Torque
Brake Pedal Bolts:
25 N·m (2.5 kgf·m, 18 ft·lb)
•
While pushing down the brake pedal, tighten the rear master cylinder mounting bolts.
Tightening Torque
Rear Master Cylinder Mounting Bolts:
9.8 N·m (1.0 kgf·m, 87 in·lb)
•
Check the engine oil level.
81
Valve Clearance
Valve and valve seat wear decreases valve clearance, upsetting valve timing.
NOTICE
If valve clearance is left unadjusted, wear will eventually cause the valves to remain partly open, which lowers performances, burns the valves and valve seats, and may cause serious engine damage.
Valve clearance for each valve should be checked and adjusted in accordance with the Periodic Maintenance Chart.
NOTE
○
If the engine is hot, wait until the engine cools.
Valve clearance must be checked when the engine is cold (room temperature).
j
j
82
Valve Clearance Inspection
•
Remove the spark plug cap (see Spark Plug section).
•
Remove the cylinder head cover bolts and cylinder head cover.
•
Remove the head cover gasket and spark plug hole gasket.
A. Cylinder Head Cover Bolts and Washers
B. Cylinder Head Cover
A. Head Cover Gasket
B. Spark Plug Hole Gasket
•
Remove the two caps from the magneto cover.
83
•
Bring the piston to the Top Dead Center (TDC) of its compression stroke to inspect the valve clearance (the position at the end of the compression stroke) by aligning the top mark with the groove on the magneto cover while turning the crankshaft counterclockwise.
j
A. Timing Inspection Cap
B. Flywheel Nut Cap
A. Top Mark
B. Groove on Magneto Cover
C. Crankshaft
D. Crankshaft Rotation Direction
j
84
•
At this point, the timing marks on the camshaft sprockets must be almost aligned with the cylinder head upper surface as shown in the figure.
A. Timing Marks
B. Camshaft Sprockets
C. Cylinder Head Upper Surface
•
Using the thickness gauge, measuring the clearance between each cam lobe and valve lifter, for all four valves.
NOTE
○
Record the measured valves clearance.
A. Thickness Gauge
Standard Valve Clearance
Exhaust 0.17
∼ 0.22 mm (0.0067
∼ 0.0087 in.)
Intake 0.10
∼ 0.15 mm (0.0039
∼ 0.0059 in.)
•
If the valve clearance is not within the specified range, adjust by an authorized Kawasaki dealer or a competent mechanic following the instructions in the Service Manual.
•
Using a high flash-point solvent, clean off any oil or dirt that may be on the silicone sealant coating area. Dry them with a clean cloth.
•
Apply silicone sealant to the cylinder head as shown in the figure.
85
•
Replace the spark plug hole gasket with a new one, and install it.
j
A. Silicone Sealant
•
Replace the head cover gasket with a new one.
•
Install the head cover gasket on the cylinder head.
A. Head Cover Gasket
B. Spark Plug Hole Gasket
j
86
•
Make sure that the upper chain guide is bottomed to the cylinder head cover.
Tightening Torque
Cylinder Head Cover Bolts:
9.8 N·m (1.0 kgf·m, 87 in·lb)
•
Install the two caps to the magneto cover.
Tightening Torque
Timing Inspection Cap:
3.5 N·m (0.36 kgf·m, 31 in·lb)
Flywheel Nut Cap:
3.5 N·m (0.36 kgf·m, 31 in·lb)
•
Install the removed parts.
A. Upper Chain Guide
B. Cylinder Head Cover
NOTICE
Unless the upper chain guide is bottomed, the camshaft chain could push the cylinder head cover upward, leading to an oil leak.
•
Install the cylinder head cover.
•
Install the washer with the metal side upwards to the cylinder head cover, and tighten the bolts to the specified torque.
Exhaust System
The exhaust system, in particular the muffler body, is designed to reduce exhaust noise and conduct the exhaust gases away from the rider while minimizing power loss. If carbon has built up inside the muffler body, exhaust efficiency is reduced, causing engine performance to drop.
If the muffler body is badly damaged, dented, cracked or rusted, replace it. Replace the silencer wool if the exhaust noise becomes too loud or engine performance drops.
Silencer Wool Replacement
•
Remove the bolts and right side cover.
•
Remove the muffler cover bolts.
•
Remove the muffler mounting bolt.
87
A. Muffler Cover Bolts
B. Muffler Mounting Bolt j
A. Bolts
B. Right Side Cover
j
88
•
Remove the muffler cover with the plastic mallet.
•
Replace the silencer wool with a new one.
•
Remove the silicone sealant attaching on the muffler cover and muffler body.
•
Using a high flash-point solvent, clean off any oil or dirt that may be on the silicone sealant coating area. Dry them with a clean cloth.
•
Arrange the shape of the silencer wool and install the muffler cover to the muffler body.
A. Plastic Mallet
B. Muffler Cover
A. Silencer Wool
B. Muffler Body
C. Muffler Cover
•
Check that the exhaust port of the muffler cover align with the muffler body.
89
•
Apply a non-permanent locking agent to the muffler body cover bolts.
•
Tighten the muffler cover bolts and apply the silicone sealant to the joint part of the muffler cover and muffler body.
j
A. Muffler Body End
B. Baffle
A. Muffler Cover
B. Muffler Body
C. Muffler Cover Bolts
D. Silicone Sealant
NOTE
○
If the threaded holes of the muffler cover and muffler body do not align, remove the muffler clamp bolt and muffler mounting bolts.
j
90
•
•
Firstly, tighten the muffler mounting bolt (front).
•
Secondly, tighten the muffler mounting bolt (rear).
Thirdly, tighten the muffler clamp bolt.
•
Insert the tabs of the side cover into the slots of the air cleaner housing, and tighten the bolts.
A. Muffler Mounting Bolt (Front)
B. Muffler Clamp Bolt
C. Muffler Body
A. Tabs
B. Slots
Drive Chain
For safety and to prevent excessive wear, the drive chain must be checked, adjusted, and lubricated before riding. If the chain becomes badly worn or maladjusted - either too loose or too tight - it could jump off the sprockets or break.
WARNING
A chain that breaks or jumps off the sprockets could snag on the engine sprocket or lock the rear wheel, severely damaging the motorcycle and causing it to go out of control. Inspect the chain for damage and proper adjustment before each ride.
Chain Slack Inspection
•
Raise the rear wheel off the ground, then rotate the rear wheel to find the place where the chain is tightest (because it wears unevenly).
•
Push up the drive chain in the middle of the upper chain run to measure the chain slack. The distance between the bottom of the chain and the swingarm (at the end of the chain slipper) should be within the standard value.
Drive Chain Slack
Standard 52 ∼ 58 mm (2.0
∼ 2.3 in.)
91
•
Adjust the drive chain if its slack is out of specification.
A. Chain Slack
•
In addition to checking the slack, rotate the rear wheel to inspect the drive chain for damaged rollers, loose pins and links and the sprockets for unevenly or excessively worn and damaged teeth.
•
If there are any such defects, replace the drive chain and/or the sprockets.
j
j
92
•
Chain Slack Adjustment
Remove the cotter pin from the rear axle nut.
•
Loosen the rear axle nut and both chain adjuster locknuts.
•
Turn both chain adjusting bolts evenly until the drive chain slack (measured between the chain and the swingarm) is within the standard value.
For the rear wheel to be properly aligned, the notch of the left chain adjuster should align with the same swingarm mark that the notch of the right chain adjuster aligns with.
Drive Chain Slack
52 ∼ 58 mm (2.0
∼ 2.3 in.)
A. Rear Axle Nut
B. Adjusting Bolt
C. Locknut
D. Marks
E. Notch
F. Cotter Pin
NOTE
○
Wheel alignment can also be checked using the straightedge or string method.
WARNING
Misalignment of the wheel will result in abnormal wear, and may result in an unsafe riding condition. Align the rear wheel using the marks on the swingarm or measuring the distance between the center of the axle and swingarm pivot.
•
Tighten both chain adjuster locknuts.
•
Tighten the axle nut to the specified torque.
Tightening Torque
Rear Axle Nut:
108 N·m (11.0 kgf·m, 79.7 ft·lb)
•
Rotate the wheel, measure the chain slack again at the tightest position, and readjust it if necessary.
•
Install a new cotter pin through the axle nut and axle, and bend its ends.
93
NOTE
○
When inserting the cotter pin, if the slots in the nut do not align with the cotter pin hole in the axle, tighten the nut clockwise up to the next alignment.
○
It should be within 30 degrees.
Loosen once and tighten again when the slot goes past the nearest hole.
j
A. Cotter Pin
A. Turning Clockwise
WARNING
A loose axle nut can lead to an accident resulting in serious injury or death. Tighten the axle nut to the proper torque and install a new cotter pin.
•
Check the rear brake effectiveness.
j
94
NOTE
○
When riding in wet and muddy conditions, mud sticks to the chain and sprockets, resulting in an overly tight chain, which can cause it to break.
To prevent this, adjust the chain slack (measured between the chain and the swingarm) to 62 mm (2.4
∼ 2.7 in.).
∼ 68
Chain Wear Inspection
When the chain has reached its wear limit (i.e., when it has stretched by 1.7% of its original length), it is no longer safe for use and should be replaced.
Since it is impractical to measure the entire length of the chain, determine the degree of wear by measuring a 20-link section of the chain.
•
Tighten the chain either by using the chain adjusters or by hanging a 10 kg (22 lb) weight on the chain.
•
Measure the 20-link length on a straight part of the chain from the center of the 1st pin to the center of the 21st pin. If the length exceeds the service limit, the chain should be replaced. Since overworn sprockets will cause a new chain to wear faster, inspect both the engine and rear sprockets whenever the chain is replaced, and replace them if necessary.
A. Weight
B. Tape Measure
Drive Chain 20-Link Length
Standard
317.5
∼ 318.2 mm (12.50
∼ 12.53
in.)
Service Limit 323 mm (12.7 in.)
NOTE
○
The drive system was designed for use with a
DAIDO DID 520DMA4 114-links chain. For maximum stretch resistance and safety, a genuine part must be used for replacement.
○
To minimize any chance of the master link coming apart, the master link clip must be installed with the closed end of the “U” pointing in the direction of chain rotation.
95
Chain Guide Wear Inspection
•
Visually inspect the drive chain guide and replace it if excessively worn or damaged.
j
A. Chain Guide
A. Master Link Clip
B. Direction of Chain Rotation
j
96
Chain Slipper Wear Inspection
•
Visually inspect the upper and lower of the chain slipper on the swingarm and replace them if worn or damaged.
Sprocket Wear Inspection
•
Visually inspect the sprocket teeth and replace the sprocket if its teeth are worn or damaged.
Sprocket Teeth Wear
A. Upper and Lower of the Chain Slipper
B. Swingarm
A. Good Teeth
B. Worn Teeth
C. Damaged Teeth
NOTE
○
Sprocket wear is exaggerated in the illustration.
Chain Lubrication
Lubrication of the drive chain is necessary after riding in the rain or mud, or any time the chain appears dry with a high quality lubricant for drive chains.
•
Apply lubricant to the side of the rollers so that it will penetrate to the rollers and bushings.
•
Wipe off any excess lubricant.
97
Adjustable Ergonomics
To suit various riding positions, the handlebar holder position can be changed and the handlebar can be adjusted by turning the handlebar holders around (180°).
The footpeg position can also be changed to suit the rider’s preference.
•
Handlebar Position Adjustment
Remove the handlebar pad.
•
Check the handlebar for damage or cracks.
•
Remove the handlebar clamp bolts, the clamps and the handlebar.
j
A. Handlebar Holder
B. Handlebar Clamp Bolts
C. Handlebar Clamps
D. Handlebar
j
98
•
Remove the handlebar holder nuts, washers and handlebar holders.
Tightening Torque
Handlebar Holder Nuts:
34 N·m (3.5 kgf·m, 25 ft·lb)
A. Handlebar Holder Nuts
B. Washers
C. Handlebar Holder
•
Select the handlebar position and install the dampers into the holes of the steering stem head so that the flat surface of dampers fit the surface of the steering stem head holes.
•
Replace the handlebar holder nuts with new ones.
•
Install the handlebar holder in the suitable direction.
•
Put the handlebar on the handlebar holder.
•
•
Temporarily install the handlebar clamps.
•
Hand tighten the handlebar clamp bolts.
Tighten the handlebar holder nuts.
A. Dampers
B. Flat Surfaces
•
Position the handlebar and use the gauge marks to check its alignment in the clamps.
There should be equal marks showing on each side of the clamps.
•
Tighten the front and rear handlebar clamp bolts equally. If the handlebar clamps are correctly installed, there will be even gaps on the front and rear sides of the clamp after the bolts are torqued.
Tightening Torque
Handlebar Clamp Bolts:
25 N·m (2.5 kgf·m, 18 ft·lb)
NOTE
○
Tighten the two clamp bolts alternately two times to ensure even tightening torque.
99
Footpeg
The right and left footpegs can be mounted in one of two positions.
•
Remove the cotter pin, pivot pin, washer, spring and footpeg.
j
A. Handlebar Clamps
B. Clamp Bolts
C. Gap
D. Supporting Bar
•
Do not disassemble the supporting bar on the handlebar.
•
Check the front brake for the proper brake effect, or no brake drag.
A. Cotter Pin
B. Pivot Pin
C. Washer
D. Spring
E. Footpeg
j
100
•
Remove the footpeg bracket bolts and bracket.
(This position is standard.)
•
•
Position the spring ends as shown in the figure.
•
Install the washer and new cotter pin.
Bend the longer end of the cotter pin.
A. Footpeg Bracket Bolts
B. Footpeg Bracket
•
Apply a non-permanent locking agent to the bracket bolts.
•
Select either footpeg position and tighten the bracket with the two bolts.
Tightening Torque
Footpeg Bracket Bolts (Upper):
34 N·m (3.5 kgf·m, 25 ft·lb)
Footpeg Bracket Bolts (Lower):
16.5 N·m (1.68 kgf·m, 12.2 ft·lb)
•
Apply grease to the pivot pin.
•
Install the footpeg, spring and pivot pin. Insert the pivot pin from the front.
A. Pivot Pin
B. Spring Ends
C. Washer
D. Cotter Pin
NOTE
○
Install the footpegs with same height on both sides. Do not ride the motorcycle with footpegs installed unevenly.
○
Adjust the positions of the shift pedal and the brake pedal to suit the rider’s preference.
○
Installing the footpegs in the lower position will reduce the amount of ground clearance and lean angle.
Brakes
Disc and disc pad wear is automatically compensated for and has no effect on the brake lever or pedal action. There are no parts on the brakes that require adjustment except brake lever position.
Brake Lever Position
The brake lever position can be adjusted to suit the rider’s preference.
•
To adjust the brake lever position, slide the front brake lever dust cover back, and loosen the locknut, and turn the adjuster to either side with a wrench.
•
After adjustment, tighten the locknut securely.
101
•
Test the braking power and check that there is no brake drag.
WARNING
Air in the brake lines diminish braking performance and can cause an accident resulting in injury or death. If the brake lever or pedal feels mushy when it is applied, there might be air in the brake lines or the brake may be defective. Have the brake checked immediately by an authorized Kawasaki dealer.
Disc Brake Fluid
Inspect the brake fluid level in the front and rear brake reservoirs and change the brake fluid in accordance with the Periodic Maintenance Chart. The brake fluid should also be changed when contaminated with dirt or water.
Use only heavy-duty brake fluid as follows.
Front/Rear Brake Fluid : DOT3 or DOT4
NOTE
○
The motorcycle is shipped with brake fluid DOT4 in the brake system.
A. Brake Lever
B. Adjuster
C. Locknut j
j
102
NOTICE
Do not spill brake fluid onto any painted surface.
Do not use fluid from a container that has been left open or that has been unsealed for a long time.
Check for fluid leakage around the brake system fittings.
Check for brake hose damage.
Brake Fluid Level Inspection (Front and Rear
Brake Reservoirs)
With the front or rear brake reservoir positioned horizontally, the brake fluid must always be above the lower level line.
A. Rear Brake Reservoir
B. Lower Level Line
A. Front Brake Reservoir
B. Lower Level Line
•
If the brake fluid in the front or rear brake reservoir is below the lower level line, check for fluid leaks in the brake line and fill the reservoir to the upper level line (The step inside the front and rear brake reservoirs indicate the upper level.).
103 j
A. Front Brake Reservoir
B. Upper Level Line
A. Rear Brake Reservoir
B. Upper Level Line
WARNING
Mixing brands and types of brake fluid can reduce the brake system’s effectiveness and cause an accident resulting in injury or death. Do not mix two brands of brake fluid. Change the brake fluid in the brake line completely if the brake fluid must be refilled but the type and brand of the brake fluid that is already in the reservoir are unidentified.
j
104
Brake Pad Wear Inspection
Inspect the brake pads for wear in accordance with the Periodic Maintenance Chart. If the thickness of any pad in any (front or rear) brake caliper is less than 1 mm (0.04 in.), have both pads in the caliper replaced as a set. Pad replacement should be done by an authorized Kawasaki dealer.
Usable Brake Pad Range
Steering
The steering should always be kept adjusted so that the handlebar will turn freely but not have excessive play.
A. Lining Thickness
B. 1 mm (0.04 in.)
Steering Inspection
•
To check the steering adjustment, raise the front wheel off the ground using a jack (special tool:
57001-1238) and attachment (special tool: 57001
-1608).
•
Push the handlebar lightly to either side. If the handlebar continues moving under its own momentum, the steering is not too tight.
•
Squatting in front of the motorcycle, grasp the lower ends of the front fork at the axle, and push and rock the front fork back and forth as shown in the figure. If play is felt, the steering is too loose and needs to be adjusted.
105
Steering Adjustment
•
Raise the front wheel off the ground using a jack
(special tool: 57001-1238) and attachment (special tool: 57001-1608).
•
•
Unlock the clamp of the number plate.
Remove the bolt.
•
Clear the projections and remove the number plate.
j
A. Clamp
B. Bolt
C. Projections
D. Number Plate
A. Push and Rock
j
106
•
Remove the handlebar (see Handlebar section).
•
Loosen the left and right front fork clamp bolts (upper).
•
Remove the steering stem head nut, and raise the steering stem head.
•
Turn the steering stem nut with a stem nut wrench
(special tool: 57001-1100) to obtain the proper adjustment.
A. Front Fork Clamp Bolts (Upper)
B. Steering Stem Head Nut
C. Steering Stem Head
A. Steering Stem Nut
B. Stem Nut Wrench (Special Tool: 57001-1100)
•
Install the steering stem head to the original position.
•
Apply the specified torques to the steering stem head nut and front fork clamp bolts (upper).
Tightening Torque
Steering Stem Head Nut:
98 N·m (10 kgf·m, 72 ft·lb)
Front Fork Clamp Bolts (Upper):
20 N·m (2.0 kgf·m, 15 ft·lb)
NOTE
○
Tighten the two clamp bolts alternately two times to ensure even tightening torque.
•
Install the handlebar (see Handlebar section), and check the steering again and readjust it if necessary.
•
Check the front brake for the proper brake effect, or no brake drag.
•
Install the removed parts.
107
Front Suspension
Front Fork Inspection
NOTICE
Sticking muds or dusts on the sliding surface of the front fork could damage to the oil seal, leading to an oil leak. Clean the sliding surface after each ride.
•
Holding the brake lever, pump the front fork back and forth manually to check for smooth operation.
•
Visually inspect the front fork for oil leakage, scoring or scratches on the outer surface of the inner tube.
•
If necessary, repair or replace by an authorized
Kawasaki dealer.
j
j
108
A. Inner Tube
WARNING
Oil leakage from the dust seal decreases the air pressure in the front fork, which can cause loss of control and an accident resulting in serious injury or death. If the seal begins to leak, replace it and any other worn or damaged parts to prevent air loss.
NOTICE
If the inner tube is badly bent or creased, replace it. Excessive bending, followed by subsequent straightening, can weaken the inner tube.
Front Fork Adjustment
Any of the following front fork adjustments can be made to tune the front suspension to the rider’s weight and the condition of the track.
Basically, there are five adjustments you can make to the front fork.
•
Air Pressure
Air pressure adjustment changes the fork spring characteristic.
Adjustable range of air pressure: 220 kPa (2.2
kgf/cm², 32 psi) to 280 kPa (2.8 kgf/cm², 41 psi).
220 kPa (2.2 kgf/cm², 32 psi) is the softest setting.
240 kPa (2.4 kgf/cm², 35 psi) is standard setting.
280 kPa (2.8 kgf/cm², 41 psi) is hardest setting.
NOTE
○
Air pressure is affected by changes of ambient temperature and atmospheric pressure. Be sure to check the air pressure before each ride.
•
Rebound Damping Adjustment
This adjustment affects how quickly the fork rebounds. Depending on the model, the fork rebound damping adjuster has at least 20 positions. The fully seated position (adjuster turned fully clockwise) is the hardest setting. Turning the adjuster 9 clicks counterclockwise from the fully seated position is the standard setting, turning it counterclockwise 20 or more clicks (depending on the model) is the softest setting.
•
Compression Damping Adjustment
This adjustment affects how quickly the fork compresses. Depending on the model, the fork compression damping adjuster has at least 22 positions.
The fully seated position (adjuster turned fully clockwise) is the hardest setting. Turning the adjuster 11 clicks counterclockwise from the fully seated position is the standard setting, turning it counterclockwise 22 or more clicks (depending on the model) is the softest setting.
•
Fork Oil Level Adjustment
The fork oil level affects only the final 100 mm (4 in.) of fork travel. A higher oil level will make the fork rebound more quickly. A lower oil level will make the fork rebound more slowly.
•
Fork Height
Steering is greatly affected by the fork height (how much the outer fork tubes protrude above the steering stem head). The less the fork tube protrudes, the lighter the front end becomes and the greater the tendency for understeering and washout due to weight biasing. Increasing the amount of fork tube protrusion has opposite effects. Be sure that the front tire does not touch the fender when the fork is fully compressed. Make this adjustment in 10 mm
(0.4 in.) steps.
109
WARNING
Improper fork leg adjustment can cause poor handling and loss of stability, which could lead to an accident. Always adjust the fork legs height on the left and right side to the same setting.
Air Pressure Adjustment
Before riding, adjust the air pressure to the specific value.
•
Remove the number plate (see Steering section).
•
Place the motorcycle on a stand so that the front wheel is off the ground the forks are fully extended.
•
Remove the air valve plug from the front fork top plug, and install the air valve adapter (Part/No.
57001-0725).
NOTE
○
When using the air valve adapter (Part/No. 57001
-0725), make sure that there is no dust or foreign material on the threads and O-ring.
○
When using the air valve adapter (Part/No. 57001
-0725), apply grease to the O-ring.
○
When the handlebar clamps are in the front position in the steering stem head, the air valve adapter (Part/No.
57001-0725) cannot be installed.
j
j
110
A. Air Valve Adapter (Part/No. 57001-0725)
•
Adjust the air pressure in each fork leg within the specified range below.
Air Pressure
Air Pressure
(Standard setting) 240 kPa (2.4 kgf/cm², 35 psi)
Adjustable Range 220
∼ 280 kPa (2.2
∼ 41 psi)
∼ 2.8
NOTE
○
Do not use the side stand during air pressure adjustment.
WARNING
When riding and transporting the motorcycle, make sure that the air pressure is within the adjustable range. If used outside the adjustable range, running stability can decrease and cause an accident resulting in serious injury or death.
Be sure to remove the air valve adapter before riding. If the air valve adapter is damaged by a stone during riding, air leakage can cause loss of control and an accident resulting in serious injury or death.
NOTICE
Do not pressurize the fork to more than 500 kPa (5.0 kgf/cm², 73 psi) or the fork may be damaged.
•
After air pressure adjustment, remove the air valve adapter (Part/No. 57001-0725).
NOTE
○
Do not ride with the air valve adapter (Part/No.
57001-0725) attached to the motorcycle.
○
Always cap the air valve adapter (Part/No. 57001
-0725) during storage.
•
Tighten the air valve plug to the specified torque.
Tightening Torque
Air Valve Plug:
0.2 N·m (0.020 kgf·m, 1.8 in·lb)
NOTICE
Be sure to install the air valve plug to prevent dust from entering.
•
Rebound Damping Adjustment
Clean the bottom of the fork tubes.
•
To adjust the rebound damping, turn the adjuster on each cylinder valve with a standard tip screwdriver. Adjust the rebound damping to suit your preference under certain conditions.
NOTICE
Do not force the rebound damping adjuster beyond the fully seated position, or the adjusting mechanism may be damaged.
111
Rebound Damping Adjuster Settings
A. Seated Position (Adjuster Turned Fully
Clockwise)
B. Softer (Counterclockwise)
C. Harder (Clockwise)
D. Standard Setting
*: Number of turns counterclockwise usable range
-20 clicks or more.
Standard Rebound Damping Adjuster Setting
9 clicks *
* Counterclockwise from the fully seated position j
A. Rebound Damping Adjuster
j
112
Compression Damping Adjustment
•
To adjust the compression damping, turn the adjuster on each front fork cylinder valve with a standard tip screwdriver. Adjust the compression damping to suit your preference and riding conditions.
NOTICE
Do not force the compression damping adjuster beyond the fully seated position, or the adjusting mechanism may be damaged.
Compression Damping Adjuster Settings
A. Compression Damping Adjuster
A. Seated Position (Adjuster Turned Fully
Clockwise)
B. Softer (Counterclockwise)
C. Harder (Clockwise)
D. Standard Setting
*: Number of turns counterclockwise usable range
-22 clicks or more.
Standard Compression Damping Adjuster
Setting
11 clicks *
* Counterclockwise from the fully seated position
Front Fork Oil Change
•
Thoroughly clean the fork before disassembly.
NOTICE
Be careful not to scratch the inner tube and not to damage the dust seal.
Avoid scratching or damaging the inner tube or the dust seal. Use a mild detergent and sponge out dirt with plenty of water.
•
Place the motorcycle on a stand so that front wheel is in the air.
•
Unscrew the front axle nut, and then loosen the left front axle clamp bolts.
113
•
Remove the brake caliper from the fork leg, and rest the caliper on some kind of stand so that it does not dangle.
•
Insert a wood wedge between the disc brake pads.
This prevents them from being moved out of their proper position, if the brake lever is squeezed accidentally.
•
Remove the brake hose clamps and both fork protectors.
j
A. Front Axle Nut
B. Left Front Axle Clamp Bolts (Loosen)
A. Brake Caliper
B. Brake Caliper Mounting Bolts
C. Brake Hose Clamps
D. Brake Hose Clamp Mounting Bolts
E. Fork Protector
F. Fork Protector Mounting Bolts
•
Loosen the right front axle clamp bolts.
•
Remove the axle, and pull out the wheel. Take off the collar from each side of the front hub.
j
114
NOTICE
Do not lay the wheel on the ground with the disc facing down. This can damage or warp the disc. Place blocks under the wheel so the disc does not touch the ground.
A. Air Valve Plug
•
Loosen the front fork clamp bolts (upper).
A. Right Front Axle Clamp Bolts (Loosen)
B. Front Axle
C. Collar
D. Fork Protector
•
•
Remove the number plate (see Steering section).
Remove the air valve plug.
•
Bleed air by pushing down the air valve.
NOTE
○
Do not compress the inner tube.
A. Front Fork Clamp Bolts (Upper)
NOTE
○
Set the rebound and compression damping to the softest settings before disassembly to minimize damping forces that can hinder disassembly.
Record the setting before turning the adjuster.
•
Loosen the front fork top plug with the top plug wrench, 49 mm (special tool: 57001-1653).
NOTE
○
Do not remove the top plug.
•
Loosen the front fork clamp bolts (lower).
115 j
A. Front Fork Clamp Bolts (Lower)
A. Front Fork Top Plug
B. Top Plug Wrench, 49 mm (Special Tool:
57001-1653)
j
116
•
Remove the front fork by pulling down while twisting it.
•
Using the top plug wrench, 49 mm (special tool:
57001-1653), remove the fork top plug from the outer tube and slowly slide down the outer tube.
A. Pull down by twisting.
B. Front Fork A. Top Plug Wrench, 49 mm (Special Tool:
57001-1653)
B. Front Fork Top Plug
C. Outer Tube
D. Slide down
•
Place a drain pan under the front fork and drain fork oil.
NOTE
○
Pump the fork tube several times to discharge the fork oil.
A. Fork Oil
117
•
Raise the outer tube and temporarily install the fork top plug to the outer tube using the top plug wrench, 49 mm (special tool: 57001-1653).
j
A. Front Fork Top Plug
B. Outer Tube
C. Top Plug Wrench, 49 mm (Special Tool:
57001-1653)
•
Protect the axle holder with a thick rag and secure it with a vise.
WARNING
Clamping the axle holder too tight can damage it which will affect riding stability.
Do not clamp the axle holder too tight.
j
118
NOTE
○
Protect the axle holder with a soft jaw or heavy cloth when using a vise.
•
Loosen the rebound adjuster assembly completely.
NOTE
○
When removing the rebound adjuster assembly, do not use an impact wrench.
•
Compress the outer tube by hand and remove the rebound adjuster assembly from the axle holder part so that the locknut appears about 20 ∼ 30 mm
(0.79
∼ 0.12 in.).
•
Hold the locknut with a wrench and remove the rebound adjuster assembly.
A. Locknut
B. Wrench
C. Rebound Adjuster Assembly
A. Axle Holder Part
B. Rebound Adjuster Assembly
•
Remove the push rod.
119
•
Remove the fork leg from the vise.
•
Remove the front fork top plug with the top plug wrench (special tool: 57001-1653).
j
A. Push Rod
NOTICE
Removing the locknut and pushing the piston rod thread into the cylinder unit will damage the oil seal. Do not remove the locknut from the piston rod.
A. Front Fork Top Plug
B. Outer Tube
C. Top Plug Wrench, 49 mm (Special Tool:
57001-1653)
•
Remove the cylinder unit from the outer tube.
NOTICE
Disassembling the cylinder unit can cause internal damage. Do not disassemble the cylinder unit.
j
120
•
Secure the top plug wrench, 49 mm (special tool:
57001-1653) with a vise and hold the fork cylinder unit with the top plug wrench.
•
Loosen the base valve assembly completely with the top plug wrench, 21 mm (special tool: 57001
-1787).
A. Cylinder Unit
B. Outer Tube
C. Piston Rod
A. Top Plug Wrench, 49 mm (Special Tool:
57001-1653)
B. Fork Cylinder Unit
C. Base Valve Assembly
D. Top Plug Wrench, 21 mm (Special Tool:
57001-1787)
•
Remove the base valve assembly from the cylinder unit.
121
NOTICE
Disassembling the base valve assembly can cause internal damage. Do not disassemble the base valve assembly.
•
Drain the fork oil from the cylinder unit by pumping the piston rod several times.
j
A. Base Valve Assembly
B. Cylinder Unit
NOTE
○
Slowly compress the piston rod until it stops so that the base valve assembly can be removed easily.
A. Fork Oil
B. Cylinder Unit
j
122
•
Hold the front fork at the inverted position for more than 20 minutes to allow the fork oil to fully drain.
•
Clean the threads of cylinder unit and base valve assembly.
A. Threads
•
Replace the O-rings on the base valve assembly and cylinder unit with new ones.
•
Apply specified fork oil to the O-rings on the base valve assembly.
123 j
A. O-rings
•
With the piston rod fully compressed, pour the specified amount of fork oil.
NOTE
○
Put a hand over the two oil holes to prevent oil leak.
A. Fork Oil
B. Oil Holes
C. Cylinder Unit
Recommended Fork Oil
KHL15-11 (1 L): P/No. 44091-0020
KHL15-11 (4 L): P/No. 44091-0021
Fork Oil Amount (Cylinder Unit)
343 mL (11.6 US oz.)
j
124
•
Pump the piston rod slowly several times to expel air.
•
Secure the piston rod in the fully compressed position.
A. Compressed Position
•
Gently install the base valve assembly to the cylinder unit.
A. Base Valve Assembly
B. Cylinder Unit
NOTE
○
Put a hand over the two oil holes to prevent oil leak.
•
Screw in the base valve assembly in the cylinder unit when the piston rod extends.
NOTE
○
When it is hard to screw in the base valve assembly, pull down the piston rod a little.
•
Hold the top plug wrench, 49 mm (special tool:
57001-1653) with a vise.
•
Holding the cylinder unit with the top plug wrench,
21 mm (special tool: 57001-1787), torque the base valve assembly to the specified torque.
125
NOTE
○
Check if the locknut is completely screwed on to the piston rod.
•
Protect the piston rod end with a heavy cloth to prevent fork damage.
•
Discharge the extra oil off the cylinder unit by pumping the piston rod to full stroke.
NOTICE
Be careful not to bend or damage the piston rod when the piston rod is stroked. Service carefully because oil flows out from the oil hole of the cylinder unit.
j
A. Top Plug Wrench, 49 mm (Special Tool:
57001-1653)
B. Cylinder Unit
C. Base Valve Assembly
D. Top Plug Wrench, 21 mm (Special Tool:
57001-1787)
Tightening Torque
Base Valve Assembly:
30 N·m (3.1 kgf·m, 22 ft·lb)
A. Piston Rod End
B. Heavy Cloth
C. Pump the Piston.
j
126
NOTE
○
Check the piston rod sliding surface for damage.
○
Apply fork oil to the piston rod sliding surface.
•
Drain the extra oil from the cylinder unit oil holes.
•
With the cylinder unit in a horizontal position, slide the piston rod by hand to be sure it is operating smoothly.
A. Oil Holes
A. Slide the Piston Rod.
B. Piston Rod
NOTICE
Be careful not to bend or damage the piston rod when the piston rod is stroked.
•
Make sure about 16 mm (0.63 in.) of push rod thread is exposed from the locknut.
127
•
Completely wipe off the fork oil from the cylinder unit.
•
Insert the cylinder unit to the outer tube.
j
A. 16 mm (0.63 in.)
B. Locknut A. Cylinder Unit
B. Outer Tube
C. Piston Rod
j
128
•
Temporarily tighten the fork top plug by using the top plug wrench, 49 mm (special tool:
57001-1653).
WARNING
Clamping the axle holder too tight can damage it which will affect riding stability.
Do not clamp the axle holder too tight.
•
Insert the push rod into the piston rod.
A. Front Fork Top Plug
B. Outer Tube
C. Top Plug Wrench, 49 mm (Special Tool:
57001-1653)
•
Clamp the axle holder with a vise.
NOTE
○
Protect the axle holder with a soft jaw or heavy cloth when using a vise.
A. Push Rod
•
Replace the O-ring and gasket on the rebound adjuster assembly with new ones and apply specified fork oil to the O-ring.
•
Slowly turn the rebound adjuster assembly clockwise until resistance is felt and check the clearance between the locknut and rebound adjuster assembly for more than 1 mm (0.04 in.).
129
•
With the outer tube compressed by hand, remove the top plug wrench, 49 mm (special tool: 57001
-1653).
•
Apply a non-permanent locking agent to the threads of rebound adjuster assembly.
•
Tighten the rebound adjuster assembly to the specified torque.
j
A. Rebound Adjuster Assembly
B. O-ring
C. Gasket
D. Locknut
E. More Than 1 mm (0.04 in.)
•
Turn the locknut counterclockwise until it contacts the rebound adjuster assembly.
•
Secure the locknut using a wrench, and tighten the rebound adjuster assembly to the specified torque.
Tightening Torque
Adjuster Assembly Locknut:
28 N·m (2.9 kgf·m, 21 ft·lb)
A. Rebound Adjuster Assembly
Tightening Torque
Rebound Adjuster Assembly:
55 N·m (5.6 kgf·m, 41 ft·lb)
•
Remove the fork leg from the vise.
j
130
•
Using the top plug wrench, 49 mm (special tool:
57001-1653), remove the fork top plug from the outer tube and slowly slide down the outer tube.
•
Pour the specified amount of fork oil into the outer tube.
A. Outer Tube
B. Fork Oil
NOTICE
Be sure the oil amount is the same in both fork legs.
Recommended Fork Oil
KHL15-11 (1 L): P/No. 44091-0020
KHL15-11 (4 L): P/No. 44091-0021
Standard Fork Oil Amount
Fork oil amount 235 mL (7.95 US oz.)
∼ 265 mL (6.42
∼ 8.96
•
Raise the outer tube and temporarily install the fork top plug to the outer tube using the top plug wrench, 49 mm (special tool: 57001-1653).
•
Install the air valve adapter (Part/No.
57001
-0725).
NOTE
○
When using the air valve adapter (Part/No. 57001
-0725), make sure that there is no dust or foreign material on the threads and O-ring.
○
When using the air valve adapter (Part/No. 57001
-0725), apply grease to the O-ring.
A. Air Valve Adapter (Part/No. 57001-0725)
•
Adjust the air pressure in each fork leg within the specified range below.
Air Pressure
Air Pressure
(Standard setting) 240 kPa (2.4 kgf/cm², 35 psi)
Adjustable Range 220
∼ 280 kPa (2.2
∼ 41 psi)
∼ 2.8
131
NOTE
○
During air pressure adjustment, be careful that the lower end of the front fork does not contact the ground surface.
NOTICE
Do not pressurize the fork to more than 500 kPa (5.0 kgf/cm², 73 psi) or the fork may be damaged.
•
Remove the air valve adapter (Part/No. 57001
-0725).
NOTE
○
Do not ride with the air valve adapter (Part/No.
57001-0725) attached to the motorcycle.
○
Always cap the air valve adapter (Part/No. 57001
-0725) during storage.
•
Install the front forks to the motorcycle.
•
Tighten the front fork clamp bolts (lower) to the specified torque.
Tightening Torque
Front Fork Clamp Bolts (Lower):
20 N·m (2.0 kgf·m, 15 ft·lb) j
j
132
•
Tighten the front fork top plug using the top plug wrench, 49 mm (special tool: 57001-1653) to the specified torque.
A. Front Fork Top Plug
B. Outer Tube
C. Top Plug Wrench, 49 mm (Special Tool:
57001-1653)
Tightening Torque
Front Fork Top Plug:
45 N·m (4.6 kgf·m, 33 ft·lb)
NOTE
○
The fork top plug torque is specified to 45 N·m (4.6
kgf·m, 33 ft·lb) however, when you use the top plug wrench, 49 mm (special tool: 57001-1653), reduce the torque to 90% of the specified value
[41 N·m (4.2 kgf·m, 30 ft·lb)] due to the distance between the center of the square hole, where the torque wrench is fitted, and that of the octagonal hole of the wrench.
○
This torque value [41 N·m (4.2 kgf·m, 30 ft·lb)] is applicable when you use a torque wrench whose length gives leverage of approximately 310 mm between the grip point to the center of the coupling square.
•
Tighten the front fork clamp (upper) bolts to the specified torque.
Tightening Torque
Front Fork Clamp Bolts (Upper):
20 N·m (2.0 kgf·m, 15 ft·lb)
A. Top Plug Wrench
B. Distance
•
Install the brake caliper to the fork leg, and tighten the brake caliper bolts to the specified torque.
Tightening Torque
Brake Caliper Bolts:
25 N·m (2.5 kgf·m, 18 ft·lb)
133
•
Take out wood wedge between the disc brake pads.
•
Apply high-temperature grease to the oil seals of the wheel.
•
Install the collars on the left and right side of the hub.
•
Put the front wheel assembly between the fork legs, and insert the front brake disc into the front brake pads.
•
Insert the front axle from the right side of the motorcycle.
•
Tighten the front axle nut to the specified torque.
Tightening Torque
Front Axle Nut:
78 N·m (8.0 kgf·m, 58 ft·lb)
•
Tighten the left front axle clamp bolts to the specified torque.
Tightening Torque
Left Front Axle Clamp Bolts:
20 N·m (2.0 kgf·m, 15 ft·lb) j
j
134
NOTE
○
Do not apply the front brake during this process to stop the motorcycle from rolling forward. Put a block in front of the wheel to stop it from moving.
A. Collars
B. Caps
C. Axle
D. Right Front Axle Clamp Bolts
E. Axle Nut
F. Left Front Axle Clamp Bolts
G. Oil Seal
NOTE
○
Tighten the two clamp bolts alternately two times to ensure even tightening torque.
•
•
Remove the jack and attachment.
Install the parts removed.
•
Before tightening the clamp bolts on the right fork leg, pump the forks up and down 4 or 5 times to allow the right fork leg to find a neutral position on the front axle.
A. Pump up and down
B. Block
•
Tighten the right axle clamp bolts to the specified torque.
Tightening Torque
Right Front Axle Clamp Bolts:
20 N·m (2.0 kgf·m, 15 ft·lb)
NOTE
○
Tighten the two clamp bolts alternately two times to ensure even tightening torque.
•
Check the front brake for good braking power and no brake drag.
WARNING
After servicing, it takes several applications of the brake lever before the brake pads contact the disc, which could result in increased stopping distance and cause an accident resulting in injury or death. Do not attempt to ride the motorcycle until a firm brake lever is obtained by pumping the lever until the pads are against the disc.
•
Adjust the air pressure (see Air Pressure Adjustment).
•
Adjust the compression and rebound damping force adjusters.
WARNING
Improper fork leg adjustment can cause poor handling and loss of stability, which could lead to an accident. Always adjust the fork legs on the left and right side to the same setting.
•
Tighten the air valve plug to the specified torque.
135
Tightening Torque
Air Valve Plug:
0.2 N·m (0.020 kgf·m, 1.8 in·lb)
NOTICE
Be sure to install the air valve plug to prevent dust from entering.
Fork Height Adjustment
Steering is greatly affected by the fork height (how much the outer fork tubes protrude above the upper fork clamp). The less the fork tube protrudes, the lighter the front end becomes and the greater the tendency for understeering and washout due to weight biasing. Increasing the amount of fork tube protrusion has opposite effects.
Be sure that the front tire does not touch the fender when the fork is fully compressed. Make this adjustment in 10 mm (0.39 in.) steps.
NOTICE
The right and left fork tubes must be adjusted evenly.
j
j
136
A. Standard Fork Height
Standard Fork Height
5 mm (0.2 in.)*
* below the surface of the top plug
NOTE
○
Tighten the two clamp bolts alternately two times to ensure even tightening torque.
Rear Suspension (UNI-TRAK ® )
This motorcycle’s rear suspension system is called
“UNI-TRAK ® ” and consists of a rear shock absorber unit, a swingarm, two lever rods and a lever.
The operating characteristics of the UNI-TRAK ® suspension are similar to those of the front fork.
However, a linkage system is used to achieve progressive springing characteristics.
Rear Shock Absorber Inspection
NOTICE
Sticking muds or dusts on the sliding surface of the rear shock absorber could damage to the oil seal, leading to an oil leak. Clean the sliding surface after each ride.
•
Pump the seat down and up by 4 or 5 times, and inspect the smooth stroke.
•
If it does not smoothly or noise is found, inspect the oil leak and rear shock absorber mounting.
•
Visually inspect the rear shock absorber for oil leakage.
•
If necessary, repair or replace by an authorized
Kawasaki dealer.
Rear Shock Absorber Adjustment
The spring preload of the shock absorber can be adjusted or the spring can be replaced with an optional one to suit various riding conditions. In addition, the damping force can be adjusted easily, making it unnecessary to change the oil viscosity.
Rebound Damping Adjustment
To adjust the rear shock absorber rebound damping, turn the rebound damping adjuster at the bottom of the rear shock absorber with a standard tip screwdriver.
137
Rebound Damping Adjuster Settings j
A. Rebound Damping Adjuster
If the damping feels too soft or too stiff, adjust it in accordance with the following table.
A. Seated Position (Adjuster Turned Fully
Clockwise)
B. Softer (Counterclockwise)
C. Harder (Clockwise)
D. Standard Setting
*: Number of turns counterclockwise usable range
33 clicks or more.
Standard Rebound Damping Adjuster Setting
19 clicks*
*: Counterclockwise from the fully seated position
NOTICE
Do not force the rebound damping force adjuster beyond the fully seated position, or the adjusting mechanism may be damaged.
j
138
NOTE
○
Adjustment of the rebound damping adjuster for the rear suspension will slightly affect the compression damping force. Always make any damping adjustments in small steps and test their effects before using them in competition.
Compression Damping Adjustment (Gas
Reservoir)
There are two adjustments you can make to the rear shock absorber gas reservoir.
To adjust the high speed compression damping, turn the high speed compression damping adjuster.
To adjust the low speed compression damping, turn the low speed compression damping adjuster with a standard tip screwdriver.
If the damping feels too soft or too stiff, adjust it in accordance with the following table.
A. Compression Damping Adjuster for High Speed
B. Compression Damping Adjuster for Low Speed
If the damping feels too soft or too stiff, adjust it in accordance with the following table.
High Speed Compression Damping Adjuster
Settings
139
Low Speed Compression Damping Adjuster
Settings j
A. Seated Position (Adjuster Turned Fully
Clockwise)
B. Softer (Counterclockwise)
C. Harder (Clockwise)
D. Standard Setting
*: Number of turns counterclockwise usable range 2 turns or more.
Standard High Speed Compression Damping
Adjuster Setting
1 3/4 turn out*
*: Counterclockwise from the fully seated position
A. Seated Position (Adjuster Turned Fully
Clockwise)
B. Softer (Counterclockwise)
C. Harder (Clockwise)
D. Standard Setting
*: Number of turns counterclockwise usable range
22 clicks or more.
Standard Low Speed Compression Damping
Adjuster Setting
8 clicks*
*: Counterclockwise from the fully seated position
j
140
NOTICE
Do not force the compression damping force adjuster beyond the fully seated position, or the adjusting mechanism may be damaged.
NOTE
○
Adjustment of the compression damping adjuster for the rear suspension will slightly affect the rebound damping force. Always make any damping adjustments in small steps and test their effects before using them in competition.
Spring Preload Adjustment
•
Remove the rear frame with air cleaner housing
(see Throttle Body Assy section).
NOTICE
If the clamp is not removed from the air cleaner housing, the rear shock absorber spring may be damaged.
•
Raise the rear wheel off the ground using a jack
(special tool: 57001-1238) and attachment (special tool: 57001-1608).
•
Using the hook wrenches (special tools: 57001
-1101 (qt. 2)), loosen the locknut on the rear shock absorber.
A. Spring Preload Adjusting Nut
B. Locknut
C. Hook Wrenches (Special Tools: 57001-1101 (qt.
2))
•
Using the hook wrench (special tool: 57001-1101), turn the spring preload adjusting nut as required.
Turning the adjusting nut down increases the spring preload.
141
Rear Shock Absorber Spring Adjustable Range
K = 52 N/mm
(K = 5.3 kgf/mm)
126.5
∼ 138.5 mm
(4.980
∼ 5.453 in.)
K = 54 N/mm*
(K = 5.5 kgf/mm)
K = 56 N/mm
(K = 5.7 kgf/mm)
126.5
∼ 138.5 mm
(4.980
∼ 5.453 in.)
126.5
∼ 138.5 mm
(4.980
∼ 5.453 in.)
*: Standard j
A. Hook Wrench (Special Tool: 57001-1101)
B. Spring Preload Adjusting Nut
•
The standard adjusting nut position from the center of the upper rear shock absorber pivot point is
127.5 mm (5.020 in.).
•
The adjustable range is as shown in the table below.
A. Adjusting Nut Position
B. Center of Upper Rear Shock Absorber Pivot
C. Spring End
•
Tighten the locknut securely.
•
After making the adjustment, move the spring up and down to make sure that it is properly seated.
•
Install the rear frame with air cleaner housing (see
Throttle Body Assy section).
j
142
•
Install the muffler (see Exhaust System section).
•
Install the removed parts.
Optional Rear Shock Absorber Springs
Various rear shock absorber springs are available to achieve suitable rear shock absorber action in accordance with the rider’s weight and track condition.
A harder spring stiffens the shock absorber action and accelerates the rebound damping.
A softer spring softens the shock absorber action and slows down the rebound damping.
WARNING
Improper removal or installation of the rear shock absorber spring may cause the spring and/or related parts to be ejected at high velocity. Always wear eye and face protection when working on the rear shock absorber.
Removal and installation of the rear shock absorber spring should be performed by an authorized Kawasaki dealer.
Wheels
Tire Air Pressure
Tire air pressure affects traction, handling, and tire life. Adjust the tire air pressure to suit track conditions and rider preference, but keep it close within the recommended range.
•
To check the tire air pressure, remove the air valve cap, and make sure to tighten the cap securely after checking the tire pressure.
•
Reduce the tire air pressure to increase the tire tread surface on the ground when riding on a wet, muddy, sandy or slippery track.
•
Increase the tire air pressure to prevent damage or punctures (though the tires will skid more easily) when riding on a pebbly or hard track.
Tire Air Pressure Adjustable Range
80 ∼ 100 kPa (0.8
∼ 1.0 kgf/cm², 12 ∼ 14 psi)
NOTE
○
Tire air pressure should be checked when the tires are cold, before you ride the motorcycle.
Spokes and Rims
The spokes on both wheels must all be securely and evenly tightened and not be allowed to loosen.
Unevenly tightened or loose spokes will cause the rim to warp, the nipples and spokes to fatigue more quickly, and the spokes to break.
143
Bead Protector
There is a bead protector nut on the both wheels.
The bead protector nut prevents the tire and tube from slipping on the rim and damaging the valve stem. Valve stem damage may cause the tube to leak, necessitating tube replacement. In order to keep the tire and tube in position on the rim, inspect the bead protector nut before riding and tighten it if necessary. Tighten the valve stem nut finger tight only.
j
A. Spoke Wrench
A. Bead Protector Nut
Rim Runout
Set up a dial gauge on the side of the rim and rotate the wheel to measure its axial runout. The difference between the highest and lowest readings is the amount of runout.
j
144
•
Set up the dial gauge on the inner circumference of the rim and rotate the wheel to measure its radial runout. The difference between the highest and lowest readings is the amount of runout.
•
A certain amount of rim warpage (runout) can be corrected by recentering the rim, that is, by loosening some spokes and tightening other to change the position of certain portions of the rim. If the rim is badly bent, however, it should be replaced.
NOTE
○
The welding spot of the rim may show excessive runout. Disregard this when measuring rim runout.
Rim Runout
Rim Runout Maximum Limit
Axial
*TIR 2.0 mm (0.08 in.)
Radial
*: Total Indicator Reading
A. Axial Rim Runout Measurement
A. Rim
B. Axial Runout
C. Radial Runout
A. Radial Rim Runout Measurement
145
Hoses Inspection
Check the brake and fuel hoses for cracks or deterioration, and the connections for looseness in accordance with the Periodic Maintenance Chart.
•
Inspect the brake hose and fittings for deterioration, cracks and signs of leakage by bending or twisting the hoses.
•
If damaged, replace the hoses.
j
A. Leak
B. Cracks
C. Bulges
•
Check that the hose are securely connected and bolts are tightened correctly.
j
146
Tightening Torques of Nuts and Bolts
Location of nuts and bolts
Before the first ride of each day of operation, check the tightness of the nuts and bolts shown below. Check also that all cotter pins are in place and in good condition.
1. Front Fork Clamp Bolts
2. Handlebar Clamp Bolts
3. Rear Frame Mounting Bolts
4. Rear Shock Absorber Nuts
5. Spoke Nipples
6. Front Axle Clamp Bolts
7. Front Brake Disc Mounting Bolts
8. Front Axle Nut
9. Front Caliper Mounting Bolts
10. Swingarm Pivot Shaft Nut
11. Rear Sprocket Nuts
147 j
1. Steering Stem Head Nut
2. Front Master Cylinder Clamp Bolts
3. Steering Stem Nut
4. Handlebar Holder Nuts
5. Rear Master Cylinder Mounting Bolts
6. Rear Brake Disc Mounting Bolts
7. Rear Axle Nut
8. Rocker Arm Pivot Nut
9. Tie-Rod Mounting Nuts
10. Brake Pedal Bolt
j
148
Torque table
Tighten all nuts and bolts to the proper torque using an accurate torque wrench. An insufficiently tightened nut or bolt may become damaged or fall out, possibly resulting in damage to the motorcycle and injury to the rider. An overtightened nut or bolt may become damaged, broken, or fall out.
Fastener
Front Axle Clamp Bolts
N·m
20 kgf·m
2.0
ft·lb
15
Remarks
AL
Front Axle Nut
Rear Axle Nut
Spoke Nipples
Rear Sprocket Nuts
Brake Pedal Bolt
Front Brake Disc Mounting Bolts
Front Caliper Mounting Bolts
Front Master Cylinder Clamp Bolts
Rear Brake Disc Mounting Bolts
Rear Master Cylinder Mounting Bolts
Front Fork Clamp Bolts (Lower)
Front Fork Clamp Bolts (Upper)
Rear Shock Absorber Nut (Lower)
Rear Shock Absorber Nut (Upper)
Rocker Arm Pivot Nut
Swingarm Pivot Shaft Nut
Tie-Rod Mounting Nuts
Handlebar Clamp Bolts
25
8.8
23
9.8
20
78
108
2.2
34
25
9.8
59
98
59
20
34
39
25
2.5
0.90
2.3
1.0
2.0
8.0
11.0
0.22
3.5
2.5
1.0
2.0
3.5
4.0
6.0
10
6.0
2.5
58
79.7
19 in·lb
25
18
87 in·lb
18
78 in·lb
17
87 in·lb
15
44
72
44
15
25
29
18
R
G, L
L
S
L
R
R
R
AL
AL
AL
R
R
Fastener
Handlebar Holder Nuts
Steering Stem Head Nut
Steering Stem Nut
Rear Frame Mounting Bolts
N·m
34
98
4.9
34
149 kgf·m
3.5
10
0.50
3.5
ft·lb
25
72
43 in·lb
25
AL: Tighten the two clamp bolts alternately two times to ensure even tightening torque.
G: Apply grease.
L: Apply a non-permanent locking agent.
R: Replacement Parts
S: Follow the specified tightening sequence.
Remarks
R j
j
150
Cleaning Your Motorcycle
General Precautions
Frequent and proper care of your Kawasaki motorcycle will enhance its appearance, optimize overall performance, and extend its useful life. Covering your motorcycle with a high quality, breathable motorcycle cover will help protect its finish from harmful
UV rays, pollutants, and reduce the amount of dust reaching its surfaces.
WARNING
Build-up of debris or flammable material in and around the vehicle chassis, engine, and exhaust can cause mechanical problems and increase the risk of fire. When operating the vehicle in conditions that allow debris or flammable material to collect in and around the vehicle, inspect the engine, electrical component and exhaust areas frequently.
If debris or flammable materials have collected, park the vehicle outside and stop the engine. Allow the engine to cool, then remove any collected debris. Do not park or store the vehicle in an enclosed space prior to inspecting for build-up of debris or flammable materials.
•
Be sure the engine and exhaust are cool before washing.
•
Avoid applying degreaser to seals, brake pads, and tires.
•
Avoid all harsh chemicals, solvents, detergents, and household cleaning products such as ammonia-based window cleaners.
•
Gasoline, brake fluid, and coolant will damage the finish of painted and plastic surfaces: wash them off immediately.
•
Avoid wire brushes, steel wool, and all other abrasive pads or brushes.
•
Use care when washing the plastic parts as they can easily be scratched.
•
Avoid using pressure washers; water can penetrate seals and electrical components and damage your motorcycle.
•
Avoid spraying water in delicate areas such as in air intakes, throttle body assy, brake components, electrical components, muffler outlets, and fuel tank openings.
Washing Your Motorcycle
•
Rinse your bike with cold water from a garden hose to remove any loose dirt.
•
Mix a mild neutral detergent (designed for motorcycles or automobiles) and water in a bucket. Use a soft cloth or sponge to wash your motorcycle. If needed, use a mild degreaser to remove any oil or grease which build up.
•
After washing, rinse your motorcycle thoroughly with clean water to remove any residue (residue from the detergent can damage parts of your motorcycle).
•
Use a soft cloth to dry your motorcycle. As you dry, inspect your motorcycle for chips and scratches.
Do not let the water air dry as this can damage the painted surfaces.
•
Start the engine and let it idle for several minutes.
The heat from the engine will help dry moist areas.
•
Carefully ride your motorcycle at a slow speed and apply the brakes several times. This helps the brakes dry and restores its normal operating performance.
•
Lubricate the drive chain to prevent rusting.
NOTE
○
After riding in an area where the roads are salted or near the ocean, immediately wash your motorcycle with cold water. Do not use warm water as it accelerates the chemical reaction of the salt. After drying, apply a corrosion protection spray on all metal and chrome surfaces to prevent corrosion.
Semi-gloss Finish
To clean the semi-gloss finish:
•
When washing the motorcycle, always use a mild neutral detergent and water.
•
The semi-gloss finish effect may be lost when it is excessively rubbed.
•
If any doubt, consult an authorized Kawasaki dealer.
151
Painted Surfaces
After washing your motorcycle, coat painted surfaces, both metal and plastic, with a commercially available motorcycle/automotive wax. Wax should be applied once every three months or as conditions require. Avoid surfaces with “satin” or “flat” finishes.
Always use non-abrasive products and apply them according to the instructions on the container.
Plastic Parts
After washing use a soft cloth to gently dry plastic parts. When dry, treat the non-painted plastic parts with an approved plastic cleaner/polisher product.
NOTICE
Plastic parts may deteriorate and break if they come in contact with chemical substances or household cleaning products such as gasoline, brake fluid, window cleaners, thread-locking agents, or other harsh chemicals. If a plastic part comes in contact with any harsh chemical substance, wash it off immediately with water and a mild neutral detergent, and then inspect for damage.
Avoid using abrasive pads or brushes to clean plastic parts, as they will damage the part’s finish.
j
j
152
Chrome and Aluminum
Chrome and uncoated aluminum parts can be treated with a chrome/aluminum polish.
Coated aluminum should be washed with a mild neutral detergent and finished with a spray polish. Aluminum wheels, both painted and unpainted can be cleaned with special non-acid based wheel spray cleaners.
Leather, Vinyl, and Rubber
If your motorcycle has leather accessories, special care must be taken. Use a leather cleaner/treatment to clean and care for leather accessories. Washing leather parts with detergent and water will damage them, shortening their life.
Vinyl parts should be washed with the rest of the motorcycle, then treated with a vinyl treatment.
The sidewalls of tires and other rubber components should be treated with a rubber protectant to help prolong their useful life.
WARNING
Rubber protectants can be slippery and, if used on the tread area, cause loss of traction resulting in accident causing injury or death.
Do not apply rubber protectant to any tread area.
Lubrication
Lubricate the areas shown in the illustrations of this section with either motor oil or regular grease, after each race and whenever the vehicle has been operated under wet or rainy conditions, especially after using a high-pressure spray washer. Before lubricating a part, clean off any rust with rust remover and wipe off any grease, oil, dirt, or grime.
General Lubrication
Apply motor oil to the following pivots:
•
Clutch Lever
•
Front Brake Lever
•
•
Rear Brake Pedal
Rear Master Cylinder Joint Pin
•
Kick Pedal
•
Footpeg
•
Shift Pedal
153 j
j
154
Apply an aerosol cable lubricant with a pressure lubricator on all cables:
•
Clutch Cable
•
Throttle Cable
Cable Lubrication
•
Apply grease to the following points:
•
Clutch Inner Cable Upper End
Throttle Inner Cable Upper End
A. Upper End
Drive Chain Lubrication
Lubricate the drive chain after riding through rain or on wet track, or any time that the chain appears dry with a high quality lubricant for drive chains.
•
Apply oil to the sides of the rollers so that it will penetrate to the rollers and bushings.
•
Wipe off any excess oil.
155
DFI Self-Diagnosis
This motorcycle equips the DFI trouble self
-diagnosis system. Trouble diagnosis can be conducted as the following procedures.
Self-diagnosis Outline
The self-diagnosis has two modes and can be switched to another mode by grounding the self-diagnosis terminal.
User Mode
The ECU connected orange FI warning indicator light goes on when DFI system and ignition system and ignition system parts are faulty. In case of serious troubles, the ECU stops the injection/ignition operation.
j
j
156
Dealer Mode
The orange FI warning indicator light emits service code(s) to show the problem(s) which the DFI system, and ignition system has at the moment of diagnosis.
Self-diagnosis Procedures
•
Disconnect the capacitor lead connector.
A. Orange Launch Control Mode/FI Warning
Indicator Light
A. Capacitor Lead Connector
•
Connect the power supply harness (optional part:
26011-0246) to the capacitor lead connector of the main harness.
•
Connect the power supply harness (optional part:
26011-0246) to the 12 V battery as shown in the figure.
•
Connect the O/Y lead (red cap) to the positive (+) terminal first.
157
NOTE
○
Use a fully charged battery when conducting self
-diagnosis. Otherwise, the light blinks very slowly or doesn’t blink.
○
Keep the self-diagnosis terminal grounded during self-diagnosis.
•
Disconnect the self-diagnosis connector (Y lead).
j
A. Power Supply Harness (Optional Part:
26011-0246)
B. Capacitor Lead Connector
C. 12 V Battery
A. Self-diagnosis Connector (Y Lead)
j
158
•
To enter the self-diagnosis dealer mode, ground the self-diagnosis terminal for more than 2 seconds, and then keep it grounded continuously.
•
Count the blinks of the orange light to read the service code. Keep the lead ground until you finish reading the service code.
A. Orange Launch Control Mode/FI Warning
Indicator Light
B. Self-diagnosis Terminal
159
How to Read Service Codes
•
Service codes are shown by a series of long and short blinks of the orange FI warning indicator light as shown below.
•
Read 10th digit and unit digit as the orange FI warning indicator light blinks.
•
When there are a number of problems, all the service codes can be stored and the display will begin starting from the lowest number service codes in the numerical order. Then after completing all codes, the display is repeated until the self-diagnosis terminal is open.
•
If there is no problem, no code and unlight.
•
For example, if two problems occurred in the order of 21, 12, the service codes are displayed from the lowest number in the order listed.
(12 → 21) → (12 → 21) → ··· (repeated) j
•
If the problem is with the following parts, the ECU cannot memorize these problems, the orange FI warning indicator light doesn’t go on, and no service codes can be displayed.
ECU Power Source Wiring and Ground Wiring (see Service Manual)
j
21
25
13
14
31
160
NOTE
○
Even if the battery or the ECU are disconnected, or the problem is solved, all service codes remain in the
ECU.
Service Code Table
Service
Code
Orange FI Warning
Indicator Light
Problems
11 Throttle sensor malfunction, wiring open or short
12 Intake air pressure sensor malfunction, wiring open or short
Intake air temperature sensor malfunction, wiring open or short
Water temperature sensor malfunction, wiring open or short
Crankshaft sensor malfunction, wiring open or short
Gear position switch malfunction, wiring open or short
Vehicle-down sensor malfunction, wiring open or short
41 Fuel injector malfunction, wiring open or short
Service
Code
46
51
Orange FI Warning
Indicator Light
161
Problems
Fuel pump malfunction, wiring open or short
Ignition coil malfunction, wiring open or short
NOTE
○
The ECU may be involved in these problems. If all the parts and circuits checked out good, be sure to check the ECU for ground and power supply. If the ground and power supply are checked good, replace the ECU
(see Service Manual).
○
When no service code is displayed, the electrical parts of the DFI system has no fault, and the mechanical parts of the DFI system and the engine are suspect.
j
advertisement
Key Features
- Powerful engine for exceptional performance
- Advanced suspension system for optimal handling
- Lightweight and high-performance design for racing and sporting use