Dubbing/Editing. Sony DCR-TRV460E, DCR-TRV461E
Advertisement
Advertisement
Dubbing/Editing
Connecting to a VCR or TV
A/V jack
You can record the picture from a VCR or TV to a tape or a “Memory Stick” inserted into
your camcorder (p. 88). You can also create a
copy of the picture recorded on your
camcorder on other recording device (p. 87).
Connect your camcorder to a TV or VCR as shown in the following illustration.
Connecting with an i.LINK cable i.LINK cable (optional) i.LINK jack
DV Interface
S VIDEO jack
Yellow
A/V connecting cable
(supplied)
Signal flow
* Pictures can be reproduced more faithfully by using an S video cable (optional). When there is an S video jack on the device to be connected, connect the S video plug to that jack instead of using the yellow video plug. The audio will not be output when you connect with the S video plug alone.
b Notes
• Use the A/V connecting cable to connect your camcorder to other devices. Before connecting, make sure the [DISPLAY] setting in the
(STANDARD SET) menu is set to [LCD PANEL]
(the default setting) (p. 81).
• When you are connecting your camcorder to monaural device, connect the yellow plug of the A/
V connecting cable to the video jack, and the red
(right channel) or the white (left channel) plug to the audio jack on the VCR or the TV.
White
Red
VCRs or TVs
To use an i.LINK cable for connection
Use an i.LINK cable (optional) to connect your camcorder to other device via the DV
Interface. The video and sound signals are transmitted digitally, producing high quality pictures. Note that you cannot record the picture
and sound separately. For details, see page 119.
86 Dubbing/Editing
Dubbing to another tape
You can copy and edit the picture played back on your camcorder to other recording devices (such as VCRs).
1
Connect your VCR to your camcorder
as a recording device (p. 86).
2
Prepare your VCR for recording.
• Insert a cassette for recording.
• If your VCR has an input selector, set it to the input mode.
3
Prepare your camcorder for playback.
• Insert the recorded cassette.
• Slide the POWER switch to select the
PLAY/EDIT mode.
4
Start the playback on your camcorder, and record it on the VCR.
Refer to the operating instructions supplied with your VCR for details.
5
When the dubbing is finished, stop your camcorder and the VCR.
b Notes
• When your camcorder is connected to the VCR via the DV Interface, you cannot record the title, indicators and words entered on the index screen of the “Memory Stick.”
• When dubbing using the A/V connecting cable, press DSPL/BATT INFO to hide indicators such as
time code (p. 54). Otherwise, they will be recorded
on the tape.
• To record the date/time and camera settings data,
have them displayed on screen (p. 54).
• Pictures edited with Picture effect ([PICT. EFFECT]
p. 68), Digital effect (p. 41, 48), or Playback zoom
(p. 53) cannot be output via the DV Interface.
• When connected using the i.LINK cable, the recorded picture becomes rough when a picture is paused on your camcorder while recording to a
VCR.
• When you dub the tape recorded on other devices in the Hi8 /standard 8 mm system via the
DV Interface, the picture may fluctuate. This is not a malfunction. Digital signals are output as image signals from the DV Interface during playback.
Dubbing/Editing 87
Recording pictures from a VCR or TV
You can record and edit pictures or TV programs from a VCR or TV on a tape or a
“Memory Stick” inserted in your camcorder.
You can also record a scene as a still image on a “Memory Stick.”
Insert a cassette or a “Memory Stick” for recording in your camcorder.
b Notes
• Your camcorder can only record from a PAL source.
For example, French video or TV programs
(SECAM) cannot be recorded correctly. See page 114 for details on TV color systems.
• If you use a 21-pin adaptor to input PAL source, you need a dual direction 21-pin adaptor (optional).
Recording movies
1
Connect your TV or VCR to your
2
If you are recording from a VCR, insert a cassette.
3
Slide the POWER switch to select the
PLAY/EDIT mode.
4
Operate your camcorder to record movies.
When recording on a tape
1 Touch .
2 Touch [ REC CTRL] with an icon.
If the item is not displayed on the screen, touch / . If you cannot find it, touch [MENU], and select it from the
3 Touch [REC PAUSE].
When recording on a “Memory
Stick”
1 Touch .
2 Touch [MENU].
3 Select the (EDIT/PLAY) menu, then [ REC CTRL] with an icon.
5
Start playing the cassette on your
VCR, or select a TV program.
The picture played on the connected device appears on the LCD screen of your camcorder.
6
Touch [REC START] at the point you want to start recording.
7
Stop recording.
When recording on a tape
Touch (stop) or [REC PAUSE].
When recording on a “Memory
Stick”
Touch [REC STOP].
8
Touch , z Tips
• The indicator appears when you connect your camcorder and other devices via an i.LINK cable.
(This indicator may also appear on your TV.)
• When recording movies on a “Memory Stick,” you can skip step 4 and press REC START/STOP in step 6.
• To enable smooth transition, we recommend that you do not mix pictures recorded in the Hi8 / standard 8 mm system on other devices with the
Digital8 system on a tape.
88 Dubbing/Editing
Recording still images
1
Perform steps 1 to 3 in “Recording movies” (p. 88).
2
Play the video, or receive the TV program you want to record.
The pictures on the VCR or TV appear on the screen of your camcorder.
3
Press PHOTO lightly at the scene you want to record. Check the image and press it fully.
The image is not recorded unless you press
PHOTO fully. Release it if you do not want to record the scene, and select other scene as described above.
Dubbing pictures from a tape to a
“Memory Stick”
You can record movies (with sound recorded in monaural) or still images on a “Memory
Stick.”
Make sure you have a recorded tape in the
Digital8 system and a “Memory Stick” inserted into your camcorder.
1
Slide the POWER switch to select the
PLAY/EDIT mode.
2
Search and record the scene you want to record.
When recording a still image
1
Touch (play) to playback the tape.
2 Press PHOTO lightly at the scene you want to record. Check the image and press it fully.
60min
101
FINE 20
CAPTURE
P-MENU
When recording a movie
1 Touch .
2 Touch [MENU].
3 Select the (EDIT/PLAY) menu, then [ REC CTRL] with an icon.
4 Touch (play) to playback the tape.
0:00:00:00 REC CTRL
REC
START
2min
5 Touch [REC START] at the point you want to start recording.
6 Touch [REC STOP] at the point you want to stop recording.
7 Touch (stop) to stop tape playback.
, continued
Dubbing/Editing 89
8 Touch , b Notes
• The Data code and titles recorded on the tape cannot be recorded on the “Memory Stick.” The time and date the picture is recorded on the “Memory Stick” will be recorded.
• The sound is recorded in 32kHz monaural.
• While recording images from a tape as still images, they are recorded in the [FRAME] mode automatically, even if you select [FIELD] in the
• If you record pictures recorded in different recording systems (Digital8 , and Hi8 /standard 8 mm on other devices), transitional scenes between recording systems may be incorrectly recorded on the “Memory Stick.” z Tips
• You can also record a movie by pressing REC
START/STOP during tape playback.
• For the recording time of movies, see page 26.
Dubbing still images from a “Memory
Stick” to a tape
You can record still images on a tape.
Make sure you have the “Memory Stick” with the images and a tape inserted into your camcorder.
1
Slide the POWER switch to select the
PLAY/EDIT mode.
2
Search for the point where you want to start dubbing by touching
(rewind) or (fast forward), then
3
Touch .
4
Touch / to select the image you want to dub.
5
Touch .
6
Touch [ REC CTRL] with an icon.
If the item is not displayed on the screen, touch / . If you cannot find it, touch
[MENU], and select it from the
(EDIT/PLAY) menu.
7
Touch [REC PAUSE].
8
Touch [REC START].
The selected image is dubbed to the tape.
9
Touch (stop) or [REC PAUSE] when you want to stop recording.
To dub other still images, select images by touching / , then repeat steps 7 to
9.
90 Dubbing/Editing
10
Touch , b Notes
• You cannot dub the index screen.
• You may not be able to dub images modified on your computer or recorded with other camcorders on your camcorder.
• You cannot dub MPEG movies on the tape.
Dubbing selected scenes from a tape
– Digital program editing
You can select up to 20 scenes (programs) and record them in the desired order to other recording device such as VCRs or to a
“Memory Stick” inserted in your camcorder.
When you are recording on a “Memory
Stick,” skip steps 1 and 2 and start from
“Recording the selected scenes as programs”
b Note
• The Digital program editing does not work with tapes recorded on other devices in the Hi8 / standard 8 mm system.
Delete unwanted scene
Change the order
Results of editing
Step 1 : Preparing your camcorder and VCR for operation
Follow the steps below when you are performing a digital program edit for the first time to a tape in a VCR. You can skip this setting if you have set up the VCR by the following procedure before.
b Note
• You cannot perform the Digital program editing on a VCR that does not support [IR SETUP] codes.
, continued
Dubbing/Editing 91
1
Connect your VCR to the camcorder
as a recording device (p. 86).
You can use either the A/V connecting cable or the i.LINK cable to make the connection. The dubbing procedure is easier with the i.LINK connection.
2
Prepare your VCR.
• Insert a cassette for recording.
• Set the input selector to input mode if your
VCR has one.
3
Prepare your camcorder (playing device).
• Insert a cassette for editing.
• Slide the POWER switch to select the
PLAY/EDIT mode.
4
Touch .
5
Touch [MENU].
60min 0:00:00:00
MEMORY SET
STILL SET
MOVIE SET
ALL ERASE
OK
6
Touch / to select (EDIT/
PLAY), then touch .
60min 0:00:00:00
D. EFFECT
PICT. EFFECT
VAR. SPD PB
REC CTRL
PROG. EDIT
REC CTRL OK
7
Touch / to select [PROG.
EDIT], then touch .
PROG. EDIT 0:00:00:00
END
Select the media.
OTHER
DEVICE
MEMORY
STICK
8
Touch [OTHER DEVICE].
PROG. EDIT
MARK
IN
START
EDIT
SET
0:00:00:00
UNDO
TOTAL
SCENE
0:00:00:00
0
END
9
Touch [EDIT SET].
PROG. EDIT
EDIT SET
1/2
CON–
TROL
CUT–
IN
0:00:00:00
END
ADJ
TEST
CUT–
OUT
10
Touch [CONTROL].
PROG. EDIT
CONTROL IR
0:00:00:00
IR i. LINK
11
Select [IR] or [i.LINK].
When connecting with an A/V connecting cable
Touch [IR], then . Follow the procedure
described in “To set the [IR SETUP] code”
When connecting with an i.LINK cable
Touch [i.LINK], then
2 : Adjusting the synchronization of the
92 Dubbing/Editing
To set the [IR SETUP] code
When you connect with an A/V connecting cable, you need to check the [IR SETUP] code signal to see if your VCR can be operated by your camcorder (infrared ray emitter).
Infrared ray emitter
Remote sensor
VCR
A/V connecting cable (supplied)
1 Touch , then [IR SETUP].
2 Select the [IR SETUP] code of your VCR with / , then touch .
For the [IR SETUP] code of your VCR,
refer to “[IR SETUP] code list” (p. 93).
When there is more than one code listed for the manufacturer of your VCR, try each code and find the most appropriate one.
3 Touch [PAUSEMODE].
4 Select the mode to cancel recording pause on your VCR, then touch .
Refer to the operating instructions supplied with your VCR for details on operation.
5 Point the infrared ray emitter of your camcorder towards the remote sensor on your VCR, from about 30 cm (12 in.) away, with no obstructions.
6 Insert a cassette into your VCR, and set the VCR to recording pause.
7 Touch [IR TEST].
8 Touch [EXEC] .
The recording starts on your VCR when the setting is correct. [Completed.] appears when the [IR SETUP] code test is finished.
Go on to “Step 2 : Adjusting the synchronization of the VCR” (p. 94).
When recording fails to start, select another
[IR SETUP] code and try again.
[IR SETUP] code list
The following [IR SETUP] codes are recorded on your camcorder by default. (It is set at “3” as the default setting.)
[IR SETUP] code Manufacturing company
Sony
Aiwa
Akai
Alba
Amstrad
Baird
Blaupunkt
Bush
CGM
Clatronic
Daewoo
Ferguson
Fisher
Funai
Goldstar
Goodmans
Grundig
Hitachi
ITT/Nokia Instant
JVC
Kendo
Loewe
Luxor
Mark
Matsui
Mitsubishi
Nokia
Nokia Oceanic
Nordmende
Okano
Orion
Panasonic
Philips
Phonola
26, 84
9, 83
42, 56
36
11, 12, 15, 21
47
16, 47, 84
89
26*
47, 58*, 60
28, 29
36, 89
89
76
60, 62, 63
58*, 70
16, 78
83, 84, 86
83, 84
1, 2, 3, 4, 5, 6
47, 53, 54
50, 62, 74
73
73
30, 36
11, 83
74
36, 47, 83
73
26
76, 83
73
80
47
, continued
Dubbing/Editing 93
Manufacturing company
Roadstar
SABA
Salora
Samsung
Sanyo
Schneider
SEG
Seleco
Sharp
Siemens
Tandberg
Telefunken
Thomson
Thorn
Toshiba
Universum
W.W. House
Watoson
* TV/VCR component
[IR SETUP] code
47
21, 76, 91
89
22, 32, 52, 93, 94
36
10, 83, 84
73
47, 74
89
10, 36
26
91, 92
76, 100
36, 47
40, 93
47, 70, 84, 92
47
58, 83
Step 2 : Adjusting the synchronization of the VCR
Follow the steps below when you are performing digital program edit for the first time to a tape in a VCR. You can skip this setting if you have set up your VCR before using the following procedure.
You can adjust the synchronization of your camcorder and the VCR to avoid not recording the starting scene.
1
Remove the cassette from your camcorder. Prepare a pen and paper to take notes.
2
Set the VCR to recording pause mode.
Skip this step if you have selected [i.LINK]
b Note
• Run the tape for about 10 seconds before pausing. The starting scenes may not get recorded when you start recording from the beginning of the tape.
3
Touch , then [ADJ TEST].
PROG. EDIT
ADJ TEST
0:00:00:00
Set the recording device in rec. pause mode.
EXEC CANCEL
4
Touch [EXEC].
A picture (about 50 seconds long) with 5
[IN] and [OUT] indicators each for adjusting synchronization is recorded.
94 Dubbing/Editing
[Completed.] appears when the recording is finished.
PROG. EDIT
ADJ TEST
Completed.
0:00:00:00
10
Touch / to select the average number value for [CUT-OUT], then touch .
The calculated stop position for recording is set.
11
Touch [END] twice.
5
Rewind the tape on your VCR, then play back in slow mode.
5 opening numbers for each [IN] and closing numbers for each [OUT] appear.
6
Take a note of the opening number value of each [CUT-IN] and the closing number value of each [CUT-OUT], then calculate the average number value for each [CUT-IN] and [CUT-
OUT].
7
Touch [CUT-IN].
0:00:00:00 PROG. EDIT
CUT–IN
0
-60~+240
8
Touch / to select the average number value for [CUT-IN], then touch .
The calculated start position for recording is set.
9
Touch [CUT-OUT].
0:00:00:00 PROG. EDIT
CUT–OUT
0
-60~+240
Recording the selected scenes as programs
When you are performing a digital program edit for the first time to a tape in a VCR, go through the procedures described in Steps 1
and 2 (p. 91 to p. 94) beforehand.
b Note
• You cannot dub the title or display indicators.
However, you can dub the title which has already been recorded on a tape.
1
Prepare a cassette or a “Memory
Stick.”
Insert a tape to be played back into the camcorder.
When you are recording on a tape, insert a cassette for recording into your VCR.
When you are recording on a “Memory
Stick,” insert a “Memory Stick” into your camcorder.
2
Touch .
3
Touch [MENU].
60min 0:00:00:00
MEMORY SET
STILL SET
MOVIE SET
ALL ERASE
OK
, continued
Dubbing/Editing 95
4
Touch / to select (EDIT/
PLAY), then touch .
60min 0:00:00:00
D. EFFECT
PICT. EFFECT
VAR. SPD PB
REC CTRL
PROG. EDIT
REC CTRL
OK
5
Touch / to select [PROG.
EDIT], then touch .
PROG. EDIT 0:00:00:00
END
Select the media.
OTHER
DEVICE
MEMORY
STICK
6
Touch the desired item.
When you are recording on a tape in the VCR
Touch [OTHER DEVICE].
PROG. EDIT
MARK
IN
START
EDIT
SET
0:00:00:00
UNDO
TOTAL
SCENE
0:00:00:00
0
END
When you are recording on a
“Memory Stick”
1 Touch [MEMORY STICK].
PROG. EDIT
MARK
IN
START
0:00:00:00
IMAGE
SIZE
UNDO
2min
TOTAL
SCENE
0:00:00
0
END
2 Touch [IMAGE SIZE] repeatedly to select the desired image size.
7
Search for the beginning of the first scene that you want to dub on your camcorder, then pause playback.
You can adjust the position with
(frame).
/
8
Touch [MARK IN].
The starting point of the first program is set, and the upper part of the program mark changes to light blue.
[IMAGE SIZE] appears when recording on a “Memory Stick.”
PROG. EDIT
MARK
OUT
START
EDIT
SET
0:00:00:00
UNDO
TOTAL
SCENE
0:00:00:00
0
END
9
Search for the end of the first scene that you want to record on your camcorder, then pause playback.
You can adjust the position with
(frame).
/
10
Touch [MARK OUT].
The ending point of the first program is set, and the lower part of the program mark changes to light blue.
PROG. EDIT
MARK
IN
START
EDIT
SET
0:00:00:00
UNDO
TOTAL
SCENE
0:00:00:12
1
END
11
Repeat steps 7 to 10 and create programs.
12
Set your VCR to recording pause.
Skip this step if your camcorder is connected via an i.LINK cable or recording on a “Memory Stick.”
96 Dubbing/Editing
13
Touch [START].
START
CANCEL
ENGAGE
REC PAUSE
0:00:00:00
EXEC
TOTAL
SCENE
0:00:00:25
3
14
Touch [EXEC].
A search for the beginning of the first program starts, then the recording starts.
[SEARCH] appears during the search and
[EDITING] appears during editing.
–x1 0:00:00:00 SEARCH
SCENE 1/3
CANCEL END
When a program is recorded, the program mark changes from orange to light blue.
When all programs have been recorded, the program editing operation stops automatically.
To cancel recording, touch [CANCEL].
To end Digital program editing
Touch [END].
To save a program without using it to record
Touch [CANCEL] in step 13.
The program is stored in memory until the cassette is ejected.
To erase programs
1
Follow steps 1 to 6 in “Recording the selected scenes as programs” (p. 95),
then touch [UNDO].
2 Touch [DEL 1MARK] to delete the last set program. Or, touch [ALL ERASE] to delete all the programs.
3 Touch [EXEC] .
The programs are deleted.
To cancel this operation, touch [CANCEL].
b Notes
• You cannot set the starting point or ending point on a blank section of the tape. If there is a blank section in the picture set as a program, the total time may not appear correctly.
• When you cannot operate the device correctly using an i.LINK cable connection, select [IR] in step 11 on
p. 92, and set the [IR SETUP] code.
Dubbing/Editing 97
Deleting recorded pictures
You can delete all or selected pictures stored on a “Memory Stick.”
1
Slide the POWER switch repeatedly to select the PLAY/EDIT mode.
2
Touch .
60min
101–0001
2 / 10 101
MEMORY PLAY
P-MENU
3
Touch / to select a picture you want to delete.
4
Touch .
DELETE
101–0001
2 / 10
Delete this image?
101
YES NO
To delete pictures on the index screen
You can easily search for the picture to be deleted by displaying 6 pictures at once.
1 Slide the POWER switch to select the
PLAY/EDIT mode.
2 Touch .
3 Touch .
4 Touch .
5 Touch [ DELETE].
6 Touch the picture you want to delete.
appears on the image to be deleted.
To display the next or the previous 6 pictures, touch / .
7 Touch .
8 Touch [YES] .
The selected pictures are deleted.
To cancel deletion, touch [NO].
b Notes
• Pictures cannot be deleted when the write-protect tab of the “Memory Stick” is set to the write-protect
position (p. 116), or when the selected picture is
• The pictures cannot be restored once they are deleted. Make sure you check the pictures before deleting them.
5
Touch [YES].
The selected picture is deleted.
To cancel deletion, touch [NO].
To delete all pictures at once
Select the (MEMORY SET) menu, then touch [
98 Dubbing/Editing
Marking recorded images with specific
5
Touch [PROTECT].
PROTECT
protection/Print mark
Make sure the write-protect tab on the
“Memory Stick” is not set to the write-protect position.
Preventing accidental erasure –
Image protection
101–0002
2/ 10 101
6
Touch the image that you want to protect.
PROTECT
appears on the selected image.
You can select and mark images to prevent accidental erasure.
1
Slide the POWER switch to select the
PLAY/EDIT mode.
2
Touch .
3
Touch .
END
101–0002
2/ 10 101 OK
7
Touch .
8
Touch [END].
To cancel image protection
Follow steps 1 to 5, then touch the image to cancel image protection.
disappears from the image.
Selecting still images for printing
– Print mark
101–0002
2/ 10 101 SET
4
Touch .
SET
PRO–
TECT
PR I NT
MARK
DELETE
PB
FOLDER
END
You can mark images that you want to print out while viewing them on your camcorder.
(You cannot specify the number of printouts.)
The DPOF (Digital Print Order Format) standard is used to select images for printing on your camcorder.
1
Slide the POWER switch to select the
PLAY/EDIT mode.
2
Touch .
, continued
Dubbing/Editing 99
3
Touch .
END
101–0002
2/ 10 101 SET
4
Touch .
SET
PRO–
TECT
PR I NT
MARK
DELETE
PB
FOLDER
END
5
Touch [PRINT MARK].
PRINT MARK
101–0002
2/ 10 101
6
Touch the image that you want to print out later.
PRINT MARK
appears on the selected image.
101–0002
2/ 10 101 OK
7
Touch .
8
Touch [END].
To cancel the Print mark
Follow steps 1 to 5, then touch the image to cancel the Print mark.
disappears from the image.
100 Dubbing/Editing b Note
• Do not mark images on your camcorder if the
“Memory Stick” already has some images with the
Print mark put on other devices. This may change the information of the images with the Print mark put on the other device.
Printing recorded images (PictBridge compliant printer)
You can easily print still images recorded on your camcorder by using a PictBridge compliant printer, even if you do not have a computer. Just set the connection in the menu setting screen of your camcorder, then connect your camcorder and printer using the
USB cable.
z Tip
• PictBridge is an industry standard established by the
Camera & Imaging Products Association (CIPA).
You can print still images without using a computer by connecting a printer directly to a digital video camera or digital still camera, regardless of model manufacturer.
Insert the “Memory Stick” on which still images are stored into your camcorder, set the paper in the printer, and turn on the power.
Connecting your camcorder to the printer
b Note
• Connect the supplied AC Adaptor to the wall outlet for the power supply.
1
Slide the POWER switch repeatedly to select the PLAY/EDIT mode.
2
Select .
3
Touch [MENU].
4
Select (STANDARD SET), then
[USB-PLY/EDT] by touching / and .
5
Select [PictBridge], then touch .
6
Touch .
7
Connect the USB jack (p. 127) of your
camcorder to a printer using the supplied USB cable.
The location of the USB jack of the printer differs depending on the model. Refer to the operating instructions supplied with your printer for details on operation.
8
Select (PICT. APPLI), then
[PRINT] by touching / and .
When connection between your camcorder and printer is complete, appears on the screen.
101–0001
1 / 10 101
END
PictBridge indication
SET EXEC
One of the images stored on the “Memory
Stick” will be displayed.
b Notes
• We cannot guarantee the operation of models that are not PictBridge compatible.
• You cannot connect your camcorder to the printer if
[USB-PLY/EDT] in the menu settings is not set to
[PictBridge]. Follow the instructions shown on the screen.
, continued
Dubbing/Editing 101
Printing
1
Select the image to be printed by touching
(next image).
(previous image)/
2
Touch , then [COPIES].
3
Select the number of copies to be printed by touching / , then touch .
You can set a maximum of 20 copies of one image to be printed.
4
Touch [END].
To print the date on the image
1 Touch ,
2 Select [DATE] or [DAY&TIME] and
.
The default setting is [OFF].
5
Touch [EXEC].
A confirmation screen appears.
101-0001
Print this?
COPIES 1
DATE/TIME OFF
1 / 10 101
YES NO
To print another image
Repeat steps 1 to 6.
To stop printing
Touch [CANCEL] while printing.
To finish printing
Touch [END] and disconnect the USB cable from your camcorder and printer.
b Notes
• Do not attempt the following operations when is on the screen. The operations may not be performed properly.
– Slide the POWER switch to select other power modes.
– Disconnecting the USB cable from your camcorder or printer.
– Removing the “Memory Stick” from your camcorder.
• If the printer stops working, disconnect the USB cable and restart the operation from the beginning.
• Some printer models may not support the date printing function. Refer to the operating instructions of your printer for details.
• We cannot guarantee the printing of images recorded with a device other than your camcorder.
6
Touch [YES].
When printing is finished, [Printing...] disappears and the image selection screen appears again.
1 / 10 101
101-0001
Printing...
Keep USB cable connected.
CANCEL
102 Dubbing/Editing

Public link updated
The public link to your chat has been updated.
Advertisement