<b>Call In Absence Indicator </b>. Motorola Profile, ENHANCED CELLULAR TELEPHONE

Users_Book Page 9 Wednesday, July 23, 1997 11:25 AM

Basic Operation

Call In Absence Indicator

If your phone is on and an incoming call is unanswered,

CALL is displayed for 16 seconds. The display and keypad backlight will then extinguish to conserve the battery level.

Pressing any key but CLR or END redisplays CALL to inform you of the call attempt. You must press CLR or END to cancel the message and clear the display.

NOTE Unless you have subscribed to Calling Line ID, the phone will not display or retrieve the phone number of the calling party.

Signal Strength Meter

The Signal Strength Meter (SSM) indicates the relative strength of the signal received by your phone. The SSM is displayed as shown below. The alone represents the lowest strength, with each additional representing a stronger signal.

Weak Signal Strong Signal

The SSM appears every time you turn your phone on. After the display blanks out (after about 16 seconds), the SSM will “strobe” to indicate that the phone is on. To redisplay the SSM press any key.

To best utilize the SSM, you should familiarize yourself with the relative signal strength levels and their associated call placement and call-in-progress qualities.

Any messages, such as Loc d , appearing in the display as a result of activation of a feature will take priority over

SSM. You will not see the SSM displayed in these cases.

9


Basic Operation

Volume Meter

The Volume Meter represents the current volume setting and is displayed whenever you adjust the earpiece or ringer volume. The volume level is displayed as a bar graph following the letter u at the left side of the display. The u alone represents the lowest volume setting, with each additional bar representing a higher volume setting.

Lowest Volume Highest Volume

Adjusting Earpiece Volume

Press and hold and hold

to raise the volume level. Press

to lower the volume.

Adjusting Ringer Volume

2. Press and hold and hold

to raise the volume level. Press

to lower the volume.

Low Battery Warning

Low battery power is indicated by a short dual-tone alert repeated periodically, and the displayed message Lo bAt . As the battery approaches discharge, the unit will automatically turn itself off.

10


Basic Operation

Battery Voltage Meter

Press , 4 .

The Battery Voltage Meter (BVM) represents the current voltage level of the battery being used. You can use this to estimate the amount of battery capacity remaining. The

BVM is displayed as a bar graph following the letter b at the left side of the display. Note that three battery symbols

( ) are also provided to indicate the relative battery level whenever the display backlighting is on.

Low Battery Charged Battery

NOTE Variables such as temperature, battery age, and charging conditions may affect battery voltage.

11


Storing Numbers in Memory

About Memory

Your phone provides a numeric memory in which to store frequently called phone numbers. The memory will accept entries designated by location numbers 01, 02, etc. Calls are placed from within memory by pressing SND when the number is displayed. Each memory location accepts up to

16 phone number digits.

The next two sections describe how to store numbers in memory and how to place calls from memory. Before setting up your memory, we suggest you read the rest of these sections to become familiar with the ways in which you will access and use it.

Storing a Phone Number

1. Enter the phone number you wish to store (up to 16 digits).

3. Enter a two-digit location number (e.g.,

0 etc.).

0

4. The location entered is displayed to confirm storage.

NOTE If FULL displays, refer to “Memory Protect

Feature” on page 13.

12



Storing an Area Code and Prefix

(Postscripting)

1. Enter the area code and prefix you wish to store.

3. Enter a two-digit location number (e.g., ,

0 etc.).

4. The location entered is displayed to confirm storage.

NOTE If FULL displays, refer to “Memory Protect

Feature” below.

Storing an area code and prefix for a frequently called location (such as an office) offers a convenient means of

“postscripting” the four-digit extension of the party you wish to call.

To place a call using postscripting, see “Recalling Area

Code and Prefix (Postscripting)” on page 17.

Memory Protect Feature

The directory has an automatic memory protect feature which prevents the accidental overwriting and loss of previously stored numbers in memory. If you attempt to store an entry to a currently occupied memory location, the location number and FULL will display. The display will then alternate between the previously stored number and ChAngE?

.

If you wish to save to that location, thus overwriting and

If you wish to store the entry in an alternate location, press

END , and the alternate location number.

13



Deleting a Memory Entry

1. Press and hold CLR , then press STO , and enter the two-digit location number you wish to delete.

2. The phone will display FULL , flash the number in memory, followed by ChAngE?

.

3. Press STO to delete, or press END to exit without deleting the entry.

Changing a Memory Entry

1. Press RCL and the two-digit location number so that the number to be changed is displayed.

2. Repeatedly press CLR to “back out” each of the digits displayed (all the digits, or just the ones you wish to change).

3. Enter the new digits.

4. Press STO and the same two-digit location number.

5. The location number and FULL will display. The display will then alternate between the currently stored number and ChAngE?

.

6. Press STO to save the newly entered number in this memory location, overwriting the currently stored number.

14


Placing Calls From Memory

About Recalling from Memory

Phone numbers stored in memory can be recalled in either of the following two ways:

• By entering a two-digit location number

• By scrolling using the Memory Location Numbers

Using any of these methods, once a phone number is displayed, you may place a call to that number by pressing

SND .

NOTE You may also scroll through the memory locations while in a call (for instance, if you want to look up a phone number to pass along to the other party). When finished, press END . This will cancel scrolling, but will not end your current call.

Placing Calls by Entering Two-Digit

Number

2. Enter the desired two-digit location number. The display shows the location number, then the last 10 digits of the stored phone number. Press RCL again to view the complete number.

3. Press SND to place a call to the number stored at the two-digit memory location.

15


Placing Calls From Memory

Placing Calls by Scrolling

This method allows you to review your memory locations by memory number, beginning with the location of your choice. This is useful when searching for a specific number in memory when you are not certain of its location.

1. Press RCL , then the two-digit memory location number where you wish to begin your review. (For example, to scroll from the beginning, press RCL ,

0

2. The location number and digits stored will appear in the display. An apostrophe (‘) following the location number confirms that you have enabled memory scrolling.

3. Press to scroll forward thru the memory locations.

Press to scroll backwards.

4. At any time while scrolling, you may press place a call to the displayed number.

SND to

NOTE Memory Scrolling may also be performed during a call. Pressing END while scrolling during a call extinguishes the apostrophe (‘) and cancels scrolling, but does not terminate the call.

16


Advanced Memory Dialing Features

Last Number Redial

This feature automatically remembers the last phone number entered from the keypad or recalled from memory,

Recalling Last Number Called

number called.

Recalling Area Code and Prefix

(Postscripting)

1. Recall two-digit location number where an area code and prefix is stored.

2. Add additional digits as needed.

You can append additional digits to recalled numbers by if you often place calls to the same area code and prefix.

Turbo Dial Feature

Once numbers have been stored in Memory Locations 02 through 09, calls can be placed from these numbers by pressing and holding the associated key for approximately one second. A call will be placed to the phone number stored in that memory location, but the number will not be

NOTE Memory Location 01 is reserved for Priority

Calling (if the Priority Call feature is enabled; refer to “Selecting and Deselecting Features” on page 31 ).

17

398A57-QUARK pgs 4/5/0 11:45 AM Page 9


Priority Call

Press 1 and hold to automatically place a call to the priority number stored in location 01.

When Priority Call is activated on your cellular phone you can use this feature to call an important number you have stored in memory location 1 even if the phone is locked.

At any time if you dial 911 or an emergency number previously stored by your cellular service provider, the display will read " d ." If the unit is locked and you press and hold the 1 or enter an emergency number, the phone will still display

" Locked " but will place the emergency call.

If you have stored an alternate non-emergency number in memory location 01, such as your home phone number, and press and hold 1 the phone will display

" Prior ."

Please keep in mind:

• Your emergency or priority number must be stored in memory location 01 to be able to place a call when the unit is locked. Be careful not to overwrite the number stored in this location.

18

• Some cellular systems have their own emergency numbers and do not allow access to numbers such as

911. Check with your cellular service provider for details about emergency calling in your area.

Super Speed Dial Feature

1. Enter the memory location number.

2. Press SND . The number will not appear in the display.

All memory locations are equipped with the Super Speed

Dial feature. Once information is stored in these locations, the Super Speed Dial feature allows you to place a call without pressing RCL .

NOTE The sequence local operator.

0 , SND will place a call to the



Scratch Pad Memory

The scratch pad permits entry of numbers from the keypad during conversation.

If your party gives you another number to call, simply enter this from the keypad. If you make an error, press CLR to erase the last digit entered, or hold entry.

CLR to erase the entire

Advise your party that they will hear tones as you enter the number. To call the scratch pad number at the end of an ongoing conversation, press END , SND .

Two-Part Tone Dialing

Your phone provides the standard Dual Tone Multi-

Frequency (DTMF) signals typically used to access alternate long distance services, signal pagers, answering machines, etc. Generally, these services use a two-part procedure: First, a call is placed from memory or by using the keypad to a central telephone number. Then, you either receive a secondary dial tone, or are prompted to enter additional digits, such as a pager number, calling card number, etc.

To tone dial from the keypad, make the initial call, either from memory or by using the keypad. When prompted, enter additional tone digits using the keypad. The tones are automatically sent as you press the keys. Do not press

SND .

To tone dial from memory, make the initial call, either from memory or by using the keypad. When prompted, recall from memory (using RCL , location number) the number you wish to send as DTMF digits. Press RCL , SND .

Repeat these steps as required to send additional groups of numbers.

19



Memory Linking

The Memory Linking feature provides improved convenience when dialing constant number sequences, such as when accessing paging systems, retrieving voice mail, etc. It allows multiple number groups (e.g., main number, PIN, and account number) to be stored in a single memory location, each group separated by a pause ( o ).

Pauses are created by pressing FCN , SND . You may then place a call using this memory location, and sequentially transmit each number group (by pressing RCL , SND ) at the appropriate system prompt.

Example of Memory Linking

In the following example, a Memory Linked number is created to access information for a bank account. The number consists of the bank’s telephone number (123-

4567), a PIN number (888) and # sign, and an account number (22) and # sign, as shown below.

NOTE A maximum of 16 digits can be stored in a memory location. A pause counts as one digit. If your

Memory Linked number requires more than 16 digits, you can store part of the number in one memory location (e.g., the main access number) and the remainder in another memory location.

Bank's Phone Number Pause PIN # Sign

Pause

Account

Number

# Sign

20



To construct the Memory Linked number, perform the following steps.

Instruction and Key Sequence Display

1 Enter the bank’s telephone number —

1

7 or recall it from memory location xx —

RCL , x, x

1234567

2 Create a pause — FCN , SND

1

234567 o

3 Enter the PIN number and # sign —

8

345

67o888C

4 Create another pause — FCN , SND

456

7o888Co

5 Enter the account number and # sign—

2

7o8

88Co22c

6 To store the number, press STO the two-digit location number.

and

Now that the Memory Linked number has been created and stored in memory, you may place the call as follows.

1. Press RCL , 2-digit location number, and SND . (Your phone will send the bank’s phone number, and then wait at the first pause.)

2. When the system answers and prompts you for your

PIN number, simply press

PIN number and # sign.

RCL , SND to transmit your

3. When the system prompts you for your account number, press RCL , SND again to transmit your account number and # sign.

NOTE If the PIN code feature is activated (see “PIN Code

Operation” on page 29), the PIN code will automatically

21


Advanced Memory Dialing Features be sent after the first pause by pressing SND . Do not add your PIN code to the linked sequence.

NOTE If you have divided your Memory Linked number into two memory locations (e.g., 03 and 04), place the initial call by pressing RCL , 0 , 3 , . the system answers and prompts you, press RCL , 0 , 4 ,

RCL , SND

to send the first number group (up to the pause).

Press RCL , SND to send each remaining number group stored in location 04.

NOTE Some electronic systems require that DTMF tones be sent for several seconds by pressing and holding a key.

These signals, known as Long Tone DTMF, cannot be transmitted using Memory Linking. If Long Tone DTMF signals are required, you must send them manually .

22


Special Call Features

Display Own Phone Number

2. Your phone number will be displayed.

3. When you have finished viewing, press CLR .

Microphone Muting

To mute microphone

While in a call, press FCN , 6

To disable mute

.

This feature allows you to confer privately with others in the car during a call. It will disable the microphone and display M<UtE . The mute feature is canceled when you end your call .

Automatic Answer

This feature allows you to answer calls without pressing

SND . When your phone receives a call, it will ring twice and then the In Use indicator will illuminate to let you know that the call has been automatically answered and is live. Simply lift the phone to your ear and begin the conversation.

To enable/disable the Automatic Answer feature, refer to

“Selecting and Deselecting Features” on page 31.

One Minute Beep

This feature allows your phone to emit an audible tone

(“beep”) ten seconds before the end of each minute during calls.

To enable/disable the One Minute Beep feature, refer to


23



Multiple Key Answer

This feature allows the user to answer an incoming call by pressing SND , either volume button, or any other digit key after the first ring has been completed.

To enable/disable the Multiple Key Answer feature, refer to


Hands Free Operation

When using a vehicular accessory you can carry on conversations in Hands Free mode. Hands Free mode allows your cellular phone to operate like an office speakerphone. A microphone picks up your voice, while the called party’s voice is heard through an external speaker. Your entire conversation can be carried on without having to take your hands off the wheel. See the

DHFA instructions (supplied with DHFA option) for details.

Distinctive Ringer

This feature allows you to select from any of 9 ringer styles to help you distinguish your phone’s ringer from those of other phones. To select a ringer style:

2. Scroll through the menu (using or ) until ringEr and StYLE 1-9 alternate in the display.

3. Press STO . A brief sample of the ringer style currently selected will be heard, and the display will show

SELECt , then 1 9 .

4. Press 1 thru 9 , or use or to scroll through the ringer styles. A brief sample of the ringer style will be heard as you make each selection, and the display will show the number of the selected ringer style.

5. When you hear the ringer style you wish to select, press STO

1-9 SEt .

. The display will display ringEr and

6. Press END to exit the Feature Menu.

24



Multiple Language Display

This feature allows you to select in which language

(English, French, Spanish, and Portuguese) your phone will display messages and prompts. To select a language:

2. Scroll through the menu (using or ) until

SELEct and LAnguAg alternate in the display.

displayed (for example, EngLiSh ).

4. Press or to scroll through the languages

( EngLiSh , ESPAnoL , FrAnc, Portug ).

5. With the language you wish to select displayed, press

STO . SELEct and LAnguAg will alternate in the display in the language you have selected.

Extended Talk Time

The Extended Talk Time feature is useful when operating your phone in strong signal areas (i.e., not in fringe areas of cellular coverage). When enabled, this feature minimizes the signaling communications between your phone and the cellular system, thus substantially extending your battery’s charge and providing you with extra talk time.

To enable/disable the Extended Talk Time feature, refer to


25


Special System Features

About Special System Features

Some Cellular Service Providers offer enhanced features for your cellular phone. Contact your Cellular Service

Provider to see if these features are available in your area, and to receive any necessary support in using them (such as assignment of a PIN code).

NOTE If these features are not supported by your Cellular

Service Provider, selecting them will have no effect.

Calling Line ID

Your Profile phone features Calling Line ID, which allows the phone number of the calling party to be displayed in the handset (when receiving a call).

The Calling Line ID numbers are stored in the message center (a special memory in your phone), which can store up to 20 phone numbers.

NOTE You must subscribe with your Cellular Service

Provider for the Calling Line ID service.

Receiving Calls with Calling Line ID

When receiving a call that includes Calling Line ID information, the phone number of the calling party will appear in the display, letting you know who the calling party is before you answer the call. Press SND to answer the call. (Note that if you should miss the call, CALL will remain in the display.

NOTE Not all calls include the Calling Line ID information. If you receive a call that does not include this information, PriuAtE or no Id will be displayed.

Each time you receive a call that includes Calling Line ID information, the information is stored as a message(s) in the message center. Messages are stored with the most recent message in location #1 and the oldest message in the highest occupied location in the message center. When a new message is received and the message center is full,

26


Special System Features the oldest message is deleted, the rest of the messages are shifted down one location, and the new message is stored in location #1.

Recalling/Viewing Calling Line ID Messages

1. Press RCL and release, then press RCL again and hold until one of the following messages appears in the display:

HH nEQW ( HH is the number of new messages)

OO nEQW (when there are no new messages) no M<ESgS (when there are no old or new messages)

2. Scroll through the messages in the message center by pressing to move forward and to move backward.

3. Press END to exit the message center.

As you scroll through the messages, each Calling Line ID message will be labeled with either HH nEQW (new message) or HH Cid (old message), where HH is the message center location number. As you view each message, the display will cycle through the Calling Line ID information (as shown in the following example) until you scroll to the next message or place a call to the displayed number.

Example 18475551212

Placing a Call to a Calling Line ID Number

After recalling the desired Calling Line ID number (the number appearing in the display), press SND to place a call to this number.

27



Storing a Calling Line ID Number in Memory

With a Calling Line ID message displayed, press STO and select a memory location (as described in “Storing a Phone Number” on page 12). The Calling Line ID number will be stored in the selected location.

Deleting an Individual Message

1. While in the message center, scroll through the messages using and until the message you wish to delete is displayed.

2. Press and hold CLR until dELEtEd appears in the display.

After deleting a message, the message center will be automatically renumbered. For example, if message #5 is deleted, messages #6 through #20 will be moved up one to become #5 through #19.

Deleting All Messages

1. While in the message center, press and hold CLR until

ErASE and ALL?

alternate in the display. (The display will briefly show dELEtEd before ErASE and ALL?

appear.)

2. Release CLR , then press CLR again to confirm erasing all of the messages. M<SgS ErASEd will appear in the display.

Other Messaging Services

In addition to the Calling Line ID feature, some cellular systems allow other types of messages to be sent to your cellular phone.

One such service is Voice Mail Notification. This service provides a notification message to the your cellular phone each time a new message is recorded in the Voice Mail system.

Voice mail notification messages are stored in the same message center that stores your Calling Line ID numbers.

Contact your Cellular Service Provider for more information and availability of these messaging services.

28



VOX Operation

Voice Operated Transmission (VOX) is a method of conserving battery power by activating the phone’s transmitter only while talking. In this manner, your battery’s charge can be extended.

To enable/disable the VOX feature, refer to “Selecting and

Deselecting Features” on page 31.

Reminder Beeps

If your phone has Calling Line ID or Voice Mail Notification services, the Reminder Beeps feature is an audible notification to alert the user that they have received a message. It will beep every 2 minutes until the new messages have been read.

To enable/disable the Reminder Beeps feature, refer to


PIN Code Operation

Overview

Your Cellular Service Provider may require a Personal

Identification Number (PIN) when placing outbound calls.

This PIN assures the cellular system that the person placing the call is an authorized user.

If PIN operation is required in your system, you must enable PIN Code operation as described in “Selecting and

Deselecting Features” on page 31.

Placing a Call using PIN Operation

1. Enter the number you wish to call, or recall the number from memory.

3. Wait for the system prompt (usually a “Beep Beep”).

4. Enter your PIN Code number (provided by your

Cellular Service Provider).

29



NOTE Your phone is designed with a “shortcut” method for dialing the PIN Code number. Simply store your PIN

Code number (supplied by your Cellular Service Provider) in memory location 07 (as described in “Storing a Phone

Number” on page 12). Then, you may simply press SND after hearing the system prompt (for example, some systems use a double tone) when placing calls; your phone will automatically send the PIN Code number stored in memory location 07. Using this shortcut method, you will not have to enter your PIN Code number each time you place a call.

A maximum of 7 digits are allowed. (Remember – Do not store any other number in memory location 07 once you have stored your PIN number.)

30


Using the Feature Menu

About the Feature Menu

The Feature Menu allows you to review and select/deselect most of your phone’s features through the keypad and display. The table below shows all features available through the menu and the pages where detailed information is found.

Note that telephones ship from the factory with default settings whereby most features are in the canceled (or OFF) position.

NOTE There are additional features that may be available with your phone that are not accessed through the feature menu. These features are described throughout this manual.

Selecting and Deselecting Features

1. Press FCN , 1 to enter the Feature Menu.

2. Scroll the menu by pressing or until the desired feature is displayed.

STO to turn 3. Press CLR to turn the feature off, press the feature on.

4. Press END to exit the Feature Menu.

EXAMPLE To activate Automatic Answer, press FCN , 1 and scroll using or until Auto and AnSrOFF alternate in the display .

Press STO to activate this feature. The display will then alternate between Auto and AnSr_On .

Press END to exit the menu .

31



Alternate in

Display

(as shipped from factory)

Feature

OnEM<in and tM<rOFF indiu tM<rOFF ringEr

StYLE 1-9

Auto and

AnSrOFF

M< kEY and and

and

AnSrOFF

Auto and

LockOFF

One Minute Beep

Phone emits a tone ten seconds before the end of each minute during a call.

Automatic Display Timer

Displays the accumulated time in minutes and seconds during and after a call.

Distinctive Ringer

Allows you to select from 9 ringer styles to distinguish your phone’s ringer from other phones.

Automatic Answer

Automatic answer allows phone to answer calls automatically, without pressing

SND .

Multiple Key Answer

Allows you to answer an incoming call by pressing any key.

Auto Lock

Locks phone each time phone is turned off.

Page

23

37

24

23

24

39

32



Alternate in

Display


Feature Page

E M < r g C Y and u o H and

E H t E n d

O F F and

Priority Call

When enabled, you may use

1 to place a one button call to a priority number stored in Memory Location 01, even when the phone is locked.

VOX mode

Conserves battery power by causing phone to transmit only while talking.

Extended Talk Time

18

29

25 r E M < i n d and

S E L E c t and

Reminder Beeps

When enabled, audible beeps alert user that one or more messages have been received (available in some models).

Language Select

Allows you to select English,

French, Spanish or

Portuguese text for prompts appearing in the display.

29

25

33



Alternate in

Display


Feature

Pin and inActiu

Page

PIN Code Operation

When used in a Cellular

System supporting this feature, requires a Personal

Identification Number to be dialed when placing outbound calls (to provide additional system security).

29

34



Status Review

1. Press FCN

2. Scroll thru the messages by pressing or to view the features that you have changed from the factory default settings.

3. Press END to exit the feature status review.

Feature status review allows you to scroll thru the list of features that you have changed from the factory default settings (shown in previous table). If no features have been changed from the factory settings, S t d will be displayed.

Alternate in

Display

(if changed from factory defaults)

Description

P i n and A c t i u E PIN Code operation is enabled r E M < i n d and Reminder Beeps is disabled

M < S g O F F

O n E M < i n and t M < r O n

One Minute Beep is enabled

A u t o and L o c k O n Auto Lock is enabled

E M < r g C Y and

C A L L O F F u o H and O n

E H t E n d and t A L k O n

VOX mode is enabled

Extended Talk Time is enabled

A u t o and A n S r O n Automatic Answer is enabled

M < k E Y and

A n S r O n

Multiple Key Answer enabled i n d i u and t M < r O n r i n g E r and

S t Y L E 1 - 9

Automatic Display Timer is enabled

Distinctive Ringer is available

35

CallTimers Page 36 Wednesday, August 27, 1997 6:33 AM

Call Timers

About Timers

Call timers provide a useful means of monitoring the air-time spent in conversation. Your phone is equipped with three timers, resettable, individual, and cumulative. These timers operate in the background and can be displayed at any time.

Each timer begins counting as a cellular channel is assigned, or when the phone rings to signal an incoming call. If an incoming call is not answered, the timers revert to their previous values.

Individual Call Timer

To Display

This timer accumulates the air-time of a call in minutes and seconds. It automatically resets before a new call is placed and when the phone is turned off.

Resettable Call Timer

To Display

Press , , , rESEtbL alternates in display.

To Reset

CLR

This timer accumulates the air-time of all calls in minutes from the point at which it is reset. This resettable timer is generally used to track monthly air-time usage and is set in conjunction with the monthly billing cycle.

Cumulative Call Timer

To Display

Press , , , , CUM<UL alternates in display.

This non-resettable timer accumulates the phone’s total airtime in minutes, starting with the initial factory setting.

36

Black spot 45.0

°

169.71 LPI


Call Timers

Automatic Display Timer

This feature allows your phone to display (in minutes and seconds) the accumulated time during and after each call.

To enable/disable the Automatic Display Timer feature, refer to “Selecting and Deselecting Features” on page 31.

37


Security Features

About Security Codes

Your phone offers several forms of security features against unauthorized use. Activating these features requires either your three-digit unlock code, or the six-digit security code.

The factory programmed unlock code is 123 and the factory programmed security code is 000000.

NOTE It is common for the unlock code to be the last 3 digits of your phone number when it is programmed by your Service Provider.

Electronic Lock

To Lock

1. Press FCN , and hold 5 .

2.

Loc ?

will display.

3. Press STO to lock your phone, or press END

4.

to exit without locking your phone.

Loc d will display and the green indicator will light steadily.

NOTE You must press and hold 5 until Loc d appears in the display. This is a safety feature to prevent you from accidentally locking your phone.

To Unlock

Enter your three-digit unlock code. If you make an error, press CLR and start again.

The electronic lock prevents use of the phone by disabling both incoming and outgoing calls.

If a call is received while your phone is locked, the phone will ring and you must enter the unlock code before the call can be answered.

38



Displaying the Unlock Code

2. Enter your six-digit security code.

3. Press RCL . The phone will display LocCodE and your three-digit unlock code.

Changing the Unlock Code


3. Enter the new desired three-digit unlock code.

ChAngEd to and the new unlock code will display to confirm storage.

Automatic Lock

This feature automatically locks your phone each time you turn your phone off. When locked, your phone still rings while receiving an incoming call, but you cannot answer the call until you have entered the unlock code.

To enable/disable the Automatic Lock feature, refer to


Setting Outgoing Call Restrictions


3. Enter the number of the service level (1 or 4) you wish to use.

4. Press STO . The phone will display SEruicE LEuEL and the number selected.

Your phone can be set to restrict call placement (as when lending the phone to another person). Using the six-digit security code, you may select one of the following two levels of restriction.

39



Description Display

No restrictions. (Standard setting) LEuEL 4

Phone will place calls only from memory locations 1 thru

10 ( RCL , 0 1 - 1 0 , SND ). If locations 1-10 are cleared, no outgoing calls can be made. No keypad dialing. No directory storage. No Turbo

Dial or Super Speed Dial features.

LEuEL 1

To change the phone to unrestricted operation, use the procedure above and enter service level 4.

40


Cellular System Information

Cellular System Overview

There are generally two types of cellular systems serving any metropolitan area. One of these will most likely be operated by the telephone company that provides telephone service to your community, generally referred to as a wireline carrier. The other cellular service provider is a radio common carrier, referred to as a non-wireline carrier.

Your Cellular Service Operator will provide information concerning specific features, procedures, and coverage in your particular area.

Service Area

The area within which the phone operates is defined by your cellular service provider. Since this is a radio system, no exact boundaries (as on a map) can be drawn. The red

NS (No Service) flashes if you are beyond range of a service area. There may be locations within your area, such as tunnels and underground parking facilities, where the unit may act as if it were beyond range.

Weak Signal Alert

If you are called in a location the system determines is inadequate for high quality service, you may hear series of beeps to inform you of the call attempt. The caller will receive the recorded “Not In Service” message. CALL will appear in the display, and the green on indicator will flash quickly. If this occurs, you must press CLR before the phone will operate. Most systems do not impose air-time charges for such call attempts.

NOTE This indicator is controlled through the initial programming of your phone. Refer to the Programming

Guide for more details.

41



Switchhook and Advanced System

Services

During a call, pressing SND performs a switchhook function used to access enhanced Cellular System features such as call waiting and conference calls. For the functioning of these features with SND , consult your

Cellular Service Provider.

Roaming

The term “Roaming” applies to the use of cellular telephones within systems other than those designated as their “Home” systems. RM (Roam) lights whenever the phone comes within range of a visited system. As your phone begins to roam, it seeks service according to the conditions you have selected (see “Reviewing / Changing

Scanning Mode” on page 44).

Contact your system operator, or that of the visited system, for information on dialing and billing procedures.

To use alternate long distance services when roaming, be certain to dial the appropriate area code and local number to access the alternate carrier in the visited area. Then use the tone dialing sequence described on page 19. If you selected Two-System Operation (see “Two-System

Operation” on page 43), enter RCL , to verify the currently active number. This is especially important if your two home systems have different area codes, or if RM is flashing within your home service area.

42



Two-System Operation

Your cellular telephone is equipped with a feature that allows you to maintain two telephone numbers from two different system operators. Both are designated as your

‘home system’ but are accessed separately. At the time your phone was programmed, you elected whether to enable this feature and which two systems would be treated as your home systems.

While you may switch from one system to the other, only one of the two can be active at any given time. Calls are placed and received through the active system only.

To switch from one system to the other:

2. The display will blank to confirm the switch and the newly activated number will appear.

3. When you have finished viewing, press CLR .

If you have two phone numbers programmed into your phone, each time the phone is turned on, it displays a message indicating which home system type and phone number is currently active. Possible messages are as follows:

System Type and Phone Number

Non-wireline (A type) with phone number 1

Non-wireline (A type) with phone number 2

Wireline (B type) with phone number 1

Wireline (B type) with phone number 2

Display

A1

A2 b1 b2

If a call is placed to the inactive phone number, the caller will receive the “Not in Service” message.

43


Programming Scanning Modes

Overview

The characteristics that determine the way your phone operates in the Cellular System are determined by the

Scanning Mode programmed for your phone.

Reviewing / Changing Scanning Mode

Typically, the scanning mode for your phone is programmed by your Service Provider. However, you may review the current scanning mode and (if desired) change it by following these procedures.

To Review Scanning Mode

1. Press RCL , . The display will show the current active system choice.

2. Press END to exit without changing selections.

To Change Scanning Modes

1. Press RCL , . The display will show the current active system choice.

2. Repeatedly press or to cycle through the scanning modes.

3. When the desired scan setting appears in the display,

4. Press END to exit to normal operation.

NOTE Constant flashing of RM, or a steadily lit NS while within your home service area may indicate an unintentional choice has been made. If this occurs, review the System Type to see if the unit is operating in Standard

Mode, or if an alternate selection has been made.

44



Scanning Modes

The following table lists the scanning modes available for your phone.

Scanning Mode

Standard Mode

Your phone first seeks a home type system, then a non-home type.

If home system is non-wireline (type A)

If home system is wireline (type B)

Invert Preference Mode

Your phone first seeks a non-home type system.

(Select this mode if in a fringe area of your home system or in certain roaming situations.)

Display

Std Ab

Std bA

SCAn bA

If home system is non-wireline (type A)

Flashing RM = call on B system

Flashing IU= call on home system

If home system is wireline (type B)

Flashing RM = call on A system

Flashing IU= call on home system

Home Only Mode

Phone will not operate outside its home system.

Scan A Mode

Phone will operate only within nonwireline (A) systems.

Scan B Mode

Phone will operate only within wireline

(B) systems.

SCAn Ab

HOM<E

SCAn A

SCAn b

45



Scanning Mode

Enhanced Preferred Scanning Mode

Phone will scan for home or programmed preferred SIDs first. This choice requires entry of up to 60 System ID numbers for those systems in which you wish to operate. Contact your Cellular Service

Provider for SID information.

Display

P SCAn

If you have selected two system operation, the phone seeks cellular service according to the system type mode selected for each phone number.

NOTE In order to program Preferred SIDs to be used in

P SCAn mode, press 7 , , , , (spells

SYSID) , then press FCN , FCN and enter the appropriate

5-digit SID number (from your Cellular Service Provider), then press STO . Now press or to cycle through the system type choices ( HOM<E , rOAM< , or inhibit ).

With the desired system type displayed, press STO to select that choice. To program another Preferred SID, press

and repeat the above process, or press END to exit

Preferred SIDs programming.

46


Troubleshooting

Before Calling For Service

Is the phone locked?

See Electronic Lock, page 38.

Is NS (No Service) lit?

See “Start-up Status Indicators” on page 5.

Have you charged the battery?

Refer to “Prepare the Battery for Initial Use” on page 1 for charging instructions.

Have you programmed a unique operating mode?

Constant flashing of RM while in your home service area may indicate that an incompatible System Type has been selected. Refer to “Reviewing / Changing Scanning Mode” on page 44.

Is the phone operating with non-standard settings?

You may have inadvertently selected improper operating characteristics. See Feature Menu, page 31.

Have you selected the wrong home system?

If your phone is programmed for Two-System Operation

(see page 43), press telephone number.

RCL , to display the active

Are new Profile accessories not working with older Profile phones?

Because of increased charging capabilities designed into your new Profile phone, some accessories that plug into the data connector will not fit older versions of Profile phones.

NOTE Older versions of Profile charging accessories that plug into the data connector may not charge new

47


Reference

Regulations and Precautions

The U.S. Federal Communications Commission and the

Canadian Department of Communications regulate cellular radiotelephone service in their respective countries. It is important for you, the Profile phone user, to observe the applicable regulations when operating your phone in either country. In addition to these U. S. and

Canadian federal regulations, you may also be bound by certain state, provincial, territorial, and local rules and regulations, as well as by your cellular carrier’s tariff (the rates, terms, and conditions of its service). If you wish to use your phone in both the U.S. and Canada, please consult with your system operator.

Furthermore, you should remember that your Profile phone is a radiotelephone system (i.e., it combines both wireline technology, as used in your home or office telephone system, and radio technology), and that the scope of regulations and precautions is therefore broader than the scope of regulations and precautions relating to wireline-only telephone usage.

Some of the major points of consideration are set out below. Please note, however, that this “Rules, Regulations, and Precautions” section does not constitute legal advice, and is intended merely for general information purposes. If you have any specific questions, please contact your

Cellular Carrier (System Operator).

License - If your home system is in the U.S., you do not require a separate license to operate your Profile phone; obtaining a cellular telephone access number is sufficient to register you as a user. If your home system is in Canada, a separate license is required. Your carrier will assist you in the licensing process. If you wish to use your Profile phone in both the U.S. and Canada, please contact your Cellular

Carrier (System Operator). Your base should operate in only one location.

48


Reference

Denial of Service A cellular carrier may deny service temporarily or terminate service for violation of any governmental regulations or of its tariff.

Driving - Your Profile phone is considered a cellular telephone. Some jurisdictions prohibit your using a cellular telephone while driving a vehicle. Even if your jurisdiction does not have such a law, we strongly suggest that, for safety reasons, the driver use extreme caution when operating the Profile phone while the vehicle is in motion (see “Driving” on page vii).

Consumer Responsibilities - Remember that the wireline and radio regulations with respect to harassing calls, false distress calls, obscene language, etc., apply to cellular phone usage.

Privacy - As a telephone user, you have come to assume a certain standard of privacy when you place or receive a telephone call via traditional wireline systems. However, because Profile phones utilize radio transmissions to effect calls, the same standard cannot always be assured. While it is unlawful for any unauthorized person to divulge or use any information obtained from intercepting or ‘listening in on’ conversations intended for others, you should not assume that your conversation is completely secure. Commercially available scanning equipment can permit a third party to monitor the radio channels used for Profile phone calls.

Interference - No person shall interfere with or cause interference to any radio communication or signal.

Equipment Modifications - The U.S. Federal

Communications Commission has type-approved the model of Profile phone which you have purchased, and both have allocated a specific frequency range for cellular service. No changes or adjustments are to be made to your

Profile phone.

49


Reference

Message Glossary

A1 System “A” phone number 1

A2 System “A” phone number 2

Auto AnSrOFF Automatic Answer feature disabled

Auto AnSr On Automatic Answer feature enabled

Auto LockOFF Automatic Lock feature disabled

Auto Lock On Automatic Lock feature enabled b1 b2

System “B” phone number 1

System “B” phone number 2 b

CUMUL

ChAngE?

Cid dELEtEd

EngLiSh

ErASE ALL

ESPAnoL

FrAnc

Battery Meter

Precedes Cumulative Timer display (also used to display key)

Memory Protect is activated to prevent accidental overwriting of a memory location

Calling Line ID number answered

(p/o Messaging Services)

Message in message stack deleted (p/o Messaging Services)

English message prompts selected

All messages in message stack deleted (p/o Messaging Services)

Spanish message prompts selected

French message prompts selected

50


Reference

FULL

HOME inuALid LocAtn Memory location chosen for storage of phone number is invalid

LEUEL 1 Call Restriction selected

LEUEL 4

All memory locations are full or requested block is unavailable

System Type Selection — Home

Mode

Lo bAt

LocCodE

Loc d

No Restrictions (standard setting)

Low Battery

3-digit Unlock Code is displayed

Unit is locked

M kEY AnSrOFF Multiple Key Answer is disabled

M kEY AnSr On Multiple Key Answer is enabled

MSgS ErASEd All messages in Message Center erased

MUtE nEW

Pin ActiuE

Microphone muted

New message(s) received (p/o

Messaging Services)

PIN Code feature enabled

Pin inActiu PIN Code feature disabled ior Priority Call enabled

Portug Portuguese message prompts selected

P SCAn rESEtbL rEdiAL

System Type Selection —

Preferred SID Mode

Precedes Resettable Call Timer

Display

Automatic Redial

51


Reference rEMind MSgOFF Reminder Beeps feature disabled rEMind MSg On Reminder Beeps feature enabled ringEr StyLE Select from 9 ringer styles

SCAn A System Type Selection (scan nonwireline “A” only)

SCAn Ab

SCAn b

System Type Selection (scan “A” type first, then “B”)

System Type Selection (scan wireline “B” only)

SCAn bA System Type Selection (System

Type Selection (scan “B” type first, then “A”)

SELECt Ringer style chosen

SELEct LAnguAg Select language chosen

SEt

Std

Ringer style choice confirmed

Snd to rEdiAL Indicates Cellular System is busy and unable to place call

Standard setting

Std Ab System Type Selection (nonwireline standard mode)

Std bA totAL

V uOH OFF uOH On

System Type Selection (wireline standard mode)

Number of messages in message stack (p/o Messaging Services)

Volume Meter

VOX Mode feature disabled

VOX Mode feature enabled

52


Reference

Index

A

About Special System Features . . . . . . . . . . . . . 26

Advanced System Services . . . . . . . . . . . . . . . . 43

Antenna Care . . . . . . . . . . . . . . . . . . . . . . . . . . vi

Antenna, extending . . . . . . . . . . . . . . . . . . . . . . 4

Automatic Answer . . . . . . . . . . . . . . . . . . . . . . 23

Automatic Display Timer . . . . . . . . . . . . . . . . . 37

Automatic Lock . . . . . . . . . . . . . . . . . . . . . . . . 39

Automatic Redialing. . . . . . . . . . . . . . . . . . . . . . 7

B

Battery Voltage Meter . . . . . . . . . . . . . . . . . . . . . 1

C

Call Attempts, unsuccessful . . . . . . . . . . . . . . . . 7

Call, ending. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Call, placing . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Call, receiving . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Calling Line ID Feature . . . . . . . . . . . . . . . . . . 27

Cellular Operation Safety Information . . . . . . . . vi

Changing the Unlock Code . . . . . . . . . . . . . . . 39

Cumulative Call Timer . . . . . . . . . . . . . . . . . . . 36

D

Deleting All Messages . . . . . . . . . . . . . . . . . . . 28

Deleting an Individual Message . . . . . . . . . . . . 28

Deselecting Features . . . . . . . . . . . . . . . . . . . . 31

Display own phone number . . . . . . . . . . . . . . . 23

Displaying the Unlock Code. . . . . . . . . . . . . . . 39

Distinctive Ringer . . . . . . . . . . . . . . . . . . . . . . 24

Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

E

Earpiece . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Earpiece Volume . . . . . . . . . . . . . . . . . . . . . . . 10

Electronic Lock . . . . . . . . . . . . . . . . . . . . . . . . 38

Ending a Call. . . . . . . . . . . . . . . . . . . . . . . . . . . 8

53


Reference

F

Feature Menu . . . . . . . . . . . . . . . . . . . . . . . . . 31

Function Keys . . . . . . . . . . . . . . . . . . . . . . . . . . xi

H

Hands Free Operation.. . . . . . . . . . . . . . . . . . . 24

Headset Jack. . . . . . . . . . . . . . . . . . . . . . . . . . . xi

I

Illuminated Keypad . . . . . . . . . . . . . . . . . . . . . . 5

Individual Call Timer . . . . . . . . . . . . . . . . . . . . 36

L

Last Number Recall . . . . . . . . . . . . . . . . . . . . . 17

Last Number Redial . . . . . . . . . . . . . . . . . . . . . 17

Low Battery Warning . . . . . . . . . . . . . . . . . . . . 10

M

Memory Entry, changing . . . . . . . . . . . . . . . . . 14

Memory Entry, deleting . . . . . . . . . . . . . . . . . . 14

Memory Linking . . . . . . . . . . . . . . . . . . . . . . . 20

Messages, recalling/viewing . . . . . . . . . . . . . . . 27

Messaging Services . . . . . . . . . . . . . . . . . . . . . 28

Microphone Muting . . . . . . . . . . . . . . . . . . . . . 23

Mouthpiece . . . . . . . . . . . . . . . . . . . . . . . . . . . xi

Multiple Key Answer . . . . . . . . . . . . . . . . . . . . 24

Multiple Languages . . . . . . . . . . . . . . . . . . . . . 25

N

Number Display . . . . . . . . . . . . . . . . . . . . . . . . x

Numeric Keypad . . . . . . . . . . . . . . . . . . . . . . . . xi

O

One Minute Beep . . . . . . . . . . . . . . . . . . . . . . 23

P

Patent Information . . . . . . . . . . . . . . . . . . . . . . 62

Placing a Call . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Placing Call to Calling Line ID Number . . . . . . 27

Postscripting . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Priority Call . . . . . . . . . . . . . . . . . . . . . . . . 18

54


Reference

R

Recalling from Memory . . . . . . . . . . . . . . . . . . 15

Receiving a Call . . . . . . . . . . . . . . . . . . . . . . . . 8

Receiving Calls with Calling Line ID. . . . . . . . . 26

Reminder Beeps . . . . . . . . . . . . . . . . . . . . . . . 30

Resettable Call Timer. . . . . . . . . . . . . . . . . . . . 37

Retractable Antenna . . . . . . . . . . . . . . . . . . . . . . x

Review Scanning Modes . . . . . . . . . . . . . . . . . 45

Review System Types . . . . . . . . . . . . . . . . . . . . 45

Ringer Volume. . . . . . . . . . . . . . . . . . . . . . . . . 10

Roaming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

S

Scratch Pad Memory . . . . . . . . . . . . . . . . . . . . 19

Scrolling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Security Codes . . . . . . . . . . . . . . . . . . . . . . . . 38

Selecting Features . . . . . . . . . . . . . . . . . . . . . . 31

Service Area . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Setting Outgoing Call Restrictions. . . . . . . . . . . 39

Signal Strength Meter . . . . . . . . . . . . . . . . . . . . . 9

Start-up Messages . . . . . . . . . . . . . . . . . . . . . . . 4

Start-up Self Tests . . . . . . . . . . . . . . . . . . . . . . . . 4

Start-up Status Indicators . . . . . . . . . . . . . . . . . . 5

Status Indicators. . . . . . . . . . . . . . . . . . . . . . . . . x

Status Review . . . . . . . . . . . . . . . . . . . . . . . . . 35

Storing Calling Line ID Number in Memory . . . 28

Storing Numbers . . . . . . . . . . . . . . . . . . . . . . . 12

Super Speed Dial Feature . . . . . . . . . . . . . . . . . 18

Switchhook . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

T

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 47

Turbo Dial Feature . . . . . . . . . . . . . . . . . . . . . . 17

Two-Part Tone Dialing . . . . . . . . . . . . . . . . . . . 19

Two-System Operation . . . . . . . . . . . . . . . . . . . 43

55


Reference

V

Volume Meter . . . . . . . . . . . . . . . . . . . . . . . . . 10

VOX Operation . . . . . . . . . . . . . . . . . . . . . . . . 29

W

Weak Signal Alert . . . . . . . . . . . . . . . . . . . . . . 41

56


Reference

The U.S. Food and Drug Administrationís Center for

Devices and Radiological Health Consumer

Update on Mobile Phones

FDA has been receiving inquiries about the safety of mobile phones, including cellular phones and PCS phones. The following summarizes what is known--and what remains unknown-about whether these products can pose a hazard to health, and what can be done to minimize any potential risk. This information may be used to respond to questions.

Why the concern?

Mobile phones emit low levels of radiofrequency energy (i.e., radiofrequency radiation) in the microwave range while being used. They also emit very low levels of radiofrequency energy (RF), considered non-significant, when in the stand-by mode. It is well known that high levels of RF can produce biological damage through heating effects (this is how your microwave oven is able to cook food). However, it is not known whether, to what extent, or through what mechanism, lower levels of RF might cause adverse health effects as well. Although some research has been done to address these questions, no clear picture of the biological effects of this type of radiation has emerged to date. Thus, the available science does not allow us to conclude that mobile phones are absolutely safe, or that they are unsafe. However, the available scientific evidence does not demonstrate any adverse health effects associated with the use of mobile phones.

What kinds of phones are in question?

Questions have been raised about hand-held mobile phones, the kind that have a built-in antenna that is positioned close to the user's head during normal telephone conversation. These types of mobile phones are of concern because of the short distance between the phone's antenna--the primary source of the RF--and the person's head. The exposure to RF from mobile phones in which the antenna is located at greater distances from the user

(on the outside of a car, for example) is drastically lower than that from hand-held phones, because a person's RF exposure decreases rapidly with distance from the source. The safety of so-called "cordless phones," which have a base unit connected to the telephone wiring in a house and which operate at far lower power levels and frequencies, has not been questioned.

How much evidence is there that hand-held mobile phones might be harmful?

Briefly, there is not enough evidence to know for sure, either way; however, research efforts are on-going. The existing scientific evidence is conflicting and many of the studies that have been done to date have suffered from flaws in their research methods. Animal experiments investigating the effects of RF exposures characteristic of mobile phones have yielded

57


Reference conflicting results. A few animal studies, however, have suggested that low levels of RF could accelerate the development of cancer in laboratory animals. In one study, mice genetically altered to be predisposed to developing one type of cancer developed more than twice as many such cancers when they were exposed to RF energy compared to controls. There is much uncertainty among scientists about whether results obtained from animal studies apply to the use of mobile phones. First, it is uncertain how to apply the results obtained in rats and mice to humans. Second, many of the studies that showed increased tumor development used animals that had already been treated with cancer-causing chemicals, and other studies exposed the animals to the RF virtually continuously-up to 22 hours per day.

For the past five years in the United States, the mobile phone industry has supported research into the safety of mobile phones. This research has resulted in two findings in particular that merit additional study:

1. In a hospital-based, case-control study, researchers looked for an association between mobile phone use and either glioma (a type of brain cancer) or acoustic neuroma (a benign tumor of the nerve sheath). No statistically significant association was found between mobile phone use and acoustic neuroma. There was also no association between mobile phone use and gliomas when all types of types of gliomas were considered together. It should be noted that the average length of mobile phone exposure in this study was less than three years.

When 20 types of glioma were considered separately, however, an association was found between mobile phone use and one rare type of glioma, neuroepithelliomatous tumors. It is possible with multiple comparisons of the same sample that this association occurred by chance. Moreover, the risk did not increase with how often the mobile phone was used, or the length of the calls. In fact, the risk actually decreased with cumulative hours of mobile phone use. Most cancer causing agents increase risk with increased exposure. An ongoing study of brain cancers by the National Cancer Institute is expected to bear on the accuracy and repeatability of these results.

2. Researchers conducted a large battery of laboratory tests to assess the effects of exposure to mobile phone RF on genetic material. These included tests for several kinds of abnormalities, including mutations, chromosomal aberrations, DNA strand breaks, and structural changes in the genetic material of blood cells called lymphocytes. None of the tests showed any effect of the RF except for the micronucleus assay, which detects structural effects on the genetic material. The cells in this assay showed changes after exposure to simulated cell phone radiation, but only after 24 hours of exposure.

58


Reference

It is possible that exposing the test cells to radiation for this long resulted in heating. Since this assay is known to be sensitive to heating, heat alone could have caused the abnormalities to occur. The data already in the literature on the response of the micronucleus assay to RF are conflicting.

Thus, follow-up research is necessary.

FDA is currently working with government, industry, and academic groups to ensure the proper follow-up to these industryfunded research findings. Collaboration with the Cellular

Telecommunications Industry Association (CTIA) in particular is expected to lead to FDA providing research recommendations and scientific oversight of new CTIA-funded research based on such recommendations.

Two other studies of interest have been reported recently in the literature:

1. Two groups of 18 people were exposed to simulated mobile phone signals under laboratory conditions while they performed cognitive function tests. There were no changes in the subjects' ability to recall words, numbers, or pictures, or in their spatial memory, but they were able to make choices more quickly in one visual test when they were exposed to simulated mobile phone signals. This was the only change noted among more than 20 variables compared.

2. In a study of 209 brain tumor cases and 425 matched controls, there was no increased risk of brain tumors associated with mobile phone use. When tumors did exist in certain locations, however, they were more likely to be on the side of the head where the mobile phone was used. Because this occurred in only a small number of cases, the increased likelihood was too small to be statistically significant.

In summary, we do not have enough information at this point to assure the public that there are, or are not, any low incident health problems associated with use of mobile phones. FDA continues to work with all parties, including other federal agencies and industry, to assure that research is undertaken to provide the necessary answers to the outstanding questions about the safety of mobile phones.

What is known about cases of human cancer that have been reported in users of hand-held mobile phones?

Some people who have used mobile phones have been diagnosed with brain cancer. But it is important to understand that this type of cancer also occurs among people who have not used mobile phones. In fact, brain cancer occurs in the U.S.

population at a rate of about 6 new cases per 100,000 people each year. At that rate, assuming 80 million users of mobile phones (a number increasing at a rate of about 1 million per

59


Reference month), about 4800 cases of brain cancer would be expected each year among those 80 million people, whether or not they used their phones. Thus it is not possible to tell whether any individual's cancer arose because of the phone, or whether it would have happened anyway. A key question is whether the risk of getting a particular form of cancer is greater among people who use mobile phones than among the rest of the population. One way to answer that question is to compare the usage of mobile phones among people with brain cancer with the use of mobile phones among appropriately matched people without brain cancer. This is called a case-control study.

The current case-control study of brain cancers by the National

Cancer Institute, as well as the follow-up research to be sponsored by industry, will begin to generate this type of information.

What is FDA's role concerning the safety of mobile phones?

Under the law, FDA does not review the safety of radiationemitting consumer products such as mobile phones before marketing, as it does with new drugs or medical devices.

However, the agency has authority to take action if mobile phones are shown to emit radiation at a level that is hazardous to the user. In such a case, FDA could require the manufacturers of mobile phones to notify users of the health hazard and to repair, replace or recall the phones so that the hazard no longer exists.

Although the existing scientific data do not justify FDA regulatory actions at this time, FDA has urged the mobile phone industry to take a number of steps to assure public safety. The agency has recommended that the industry:

• support needed research into possible biological effects of RF of the type emitted by mobile phones;

• design mobile phones in a way that minimizes any RF exposure to the user that is not necessary for device function; and

• cooperate in providing mobile phone users with the best possible information on what is known about possible effects of mobile phone use on human health.

At the same time, FDA belongs to an interagency working group of the federal agencies that have responsibility for different aspects of mobile phone safety to ensure a coordinated effort at the federal level. These agencies are:

• National Institute for Occupational Safety and Health

• Environmental Protection Agency

• Federal Communications Commission

• Occupational Health and Safety Administration

• National Telecommunications and Information

Administration

The National Institutes of Health also participates in this group.

60


Reference

In the absence of conclusive information about any possible risk, what can concerned individuals do?

If there is a risk from these products--and at this point we do not know that there is--it is probably very small. But if people are concerned about avoiding even potential risks, there are simple steps they can take to do so. For example, time is a key factor in how much exposure a person receives. Those persons who spend long periods of time on their hand-held mobile phones could consider holding lengthy conversations on conventional phones and reserving the hand-held models for shorter conversations or for situations when other types of phones are not available.

People who must conduct extended conversations in their cars every day could switch to a type of mobile phone that places more distance between their bodies and the source of the RF, since the exposure level drops off dramatically with distance.

For example, they could switch to

• a mobile phone in which the antenna is located outside the vehicle,

• a hand-held phone with a built-in antenna connected to a different antenna mounted on the outside of the car or built into a separate package, or

• a headset with a remote antenna to a mobile phone carried at the waist.

Again, the scientific data do not demonstrate that mobile phones are harmful. But if people are concerned about the radiofrequency energy from these products, taking the simple precautions outlined above can reduce any possible risk.

Where can I find additional information?

For additional information, see the following websites:

Federal Communications Commission (FCC) RF Safety

Program (select "Information on Human Exposure to RF Fields from Cellular and PCS Radio Transmitters"): http://www.fcc.gov/oet/rfsafety

World Health Organization (WHO) International Commission

on Non-Ionizing Radiation Protection (select Qs & As): http://www.who.int/emf

United Kingdom, National Radiological Protection Board: http://www.nrpb.org.uk

Cellular Telecommunications Industry Association (CTIA): http://www.wow-com.com

U.S. Food and Drug Administration (FDA) Center for Devices

and Radiological Health: http://www.fda.gov/cdrh/consumer/

61


Reference

62

Patent Information

This phone may be manufactured under one or more of the following U.S. Patents.

4794489

4797929

4797947

4798975

4802236

4803726

4809356

4811377

4811404

4817157

4827507

4829543

4831647

4843621

4845772

4851966

4852090

4860336

4860341

4868576

5691947

5692046

5692101

5696497

5696821

5699070

5699389

5699408

5701130

5701244

5701589

5703470

5703539

5703909

5706019

5706313

5708445

5710862

5710987

5711001

5649309

5656914

5656917

5657418

5659601

5660945

5661433

5664973

5666429

5668871

5670912

5673001

5673003

5673287

5674326

5675591

5675702

5678201

5678221

5678227

5680063

5684384

5738954

5739792

5740525

5742894

5745116

5745566

5745848

5747970

5748727

5754141

5754455

5754583

5754645

5754956

5758271

5760714

5761300

5761610

5764100

5764111

4918732

4922178

4941203

4942570

4945570

4956854

4959851

4963812

4964121

4970475

5715520

5715524

5717307

5722052

5724004

5726983

5729221

5732350

5737327

5737685

4870686

4872196

4873683

4876552

4876656

4876740

4879533

4885553

4887050

4890199

4896124

4896361

4897873

4903326

4903327

4904549

4904992

4905288

4905301

4912602

4916262

4918431

5020091

5020092

5020093

5023580

5023866

5023911

5025387

5027388

5028083

5028859

5029233

5036532

5038253

5040127

5042071

5045824

5053924

5055800

5055802

5055803

4972355

4972432

4972455

4975808

4977589

4977616

4979207

4984219

4984290

4989230

4992753

4996529

5008925

5010309

5010570

5014294

5014346

5017856

5018188

5020076

5764730

5764743

5766794

5771182

5771471

5777521

5777856

5784368

5784419

5784585

5787128

5787577

5793315

5793866

5796822

5797101

5798716

5799011

5799256

5801513

5801567

5802111

4291475

4302845

4312074

4365221

4369516

4369520

4369522

4374370

4378603

4390963

4398265

4400584

4400585

4434461

4455534

4486624

4491972

4523155

4546329

4574243

4581602

4581749

4585957

4593155

4594657

4602218

4605987

4616314

4617520

4628529

4629829

4633141

4636593

4636741

4648125

4649543

4654655

4680787

4704588

4711361

4715063

4717884

4730195

4731813

4736277

4737976

4741018

4742562

4761621

4764737

4775998

4791527

5630213

5630215

5631538

5633484

5633786

5634202

5640690

5642368

5646576

5649306

5841851

5842122

5844943

5846094

5848072

5848152

5848356

5848718

5850440

5854549

5854785

5854972

5856763

5856766

5857148

5857192

5859522

5859567

5859890

5861853

5812093

5812542

5812590

5814798

5815507

5815570

5815804

5815805

5815807

5815820

5821820

5822726

5826224

5831826

5832080

5832388

5835006

5835535

5835785

5838202

5057762

5058136

5059885

5060264

5063340

5065408

5067139

5070310

5077757

5077790

5081674

5083304

5805992

5807012

5808585

5808586

5809020

5809419

5809421

5809430

5809433

5809544

5160898

5162144

5163159

5164652

5166596

5166642

5168522

5170173

5170485

5170492

5175729

5175759

5864799

5865487

5867063

5867127

5867140

5867510

5870670

5872744

5127100

5128834

5133010

5134717

5140286

5140635

5142551

5142696

5144533

5146620

5148471

5148473

5150075

5150359

5150384

5151643

5152006

5152007

5153590

5157693

5862460

5862493

5087004

5093632

5095503

5107487

5109400

5111162

5113400

5113436

5117073

5117441

5117449

5117450

5121047

5121288

5121412

5122480

5122722

5124889

5127040

5127042

5936972

5939939

5175874

5182749

5185566

5185790

5187640

5187809

5192924

5193223

5195106

5195108

5198887

5200655

5201069

5203009

5203012

5203013

5203021

5204977

5905956

5907418

5907615

5909102

5910944

5912648

5920549

5920550

5923007

5924044

5925835

5925942

5926119

5926503

5926751

5930268

5930288

5930299

5933330

5936516

5877633

5878075

5878209

5878336

5878353

5880637

5880646

5881377

5889737

5889768

5889859

5892410

5893036

5894597

5896054

5896261

5898933

5900829

5901347

5901357

5903825

5903852

5222104

5222251

5230007

5230093

5233506

5233633

5235492

5237257

5237570

5239127

5241545

5241548

5241592

5241688

5242767

5243355

5247544

5247565

5249302

5251331

5255292

5205751

5210793

5211581

5212815

5212826

5214675

5214774

5216389

5220290

5220936

5222078

5257414

5259005

5940452

5940746

5943027

5945852

5945964

5946395

5949020

5950131

5950139

5953413

5954817

5955700

5955999

5956626

5963848

5963876

5964858

5966101

5966667

5966671

5969545

5974042

5977916

5980268

5982881

5983082

5987012

5988577


6009552

6011699

6011784

6011959

6011961

6012634

6014376

6014552

6016312

6016422

5260170

5260988

5261119

5262710

5263052

5263055

5265271

5267230

5276588

5276707

5276913

5995050

5996178

5999115

5999821

5999832

6002922

6002937

6005498

6006104

6008636

6009168

6009309

6009325

6009336

5325405

5325429

5327578

5327642

5331123

5333153

5336984

5338909

5343213

5349588

5351245

5359696

5361400

5363071

5276915

5278832

5278994

5280630

5280637

5280644

5285443

5287013

5287553

5287555

5287556

5289505

5297142

5299232

5301365

5308716

5321705

5321737

5321847

5323421

5430416

5432017

5434947

5436802

5438684

5442680

5444764

5446763

5446766

5448763

5448770

5448771

5453997

5457744

5459640

5459774

5461643

5463351

5463406

5463628

5463646

5402448

5404580

5404582

5406146

5406562

5408693

5410275

5410741

5414711

5420759

5424689

5428362

5428820

5428836

D337332

D338012

D338887

D339127

D339335

D339336

D339337

D339564

D339578

D339581

D339582

D340709

D340710

D340711

5463674

5463688

5463694

5465409

5465412

5469177

5471671

D324024

D324388

D325028

D325029

D325032

D325583

D325915

D327061

D327062

D328302

D332261

D332785

D334746

D288683

D289156

D292578

D292920

D295627

D295973

D295975

D296187

D297734

D297735

D297736

D299136

D299137

D299232

D300742

D300827

D301473

D301476

D301883

D302015

D303656

5365549

5366826

5367538

5367558

5371791

5373101

5375143

6018584

6018651

6018671

6021332

D284759

D285439

D288432

D316417

D316859

D320780

D322783

5375258

5379324

5381114

5384825

5392000

5392023

5392331

5396654

5401927

5402447

D304189

D305427

D305717

D306015

D306163

D306293

D306299

D306441

D306583

D306594

D307271

D309301

D309451

D314173

D315330

D315346

D315543

D315559

D315565

D315907

5588041

5589796

5590177

5594778

5594951

5598129

5598431

5600341

5604050

5604468

5604787

5606332

5606560

5606730

5613229

5613863

5615233

5615259

5615260

5621763

5621766

5625316

5625683

5628001

5628057

5628089

5629979

5630159

5630210

D369359

D369797

5561437

5561852

5565881

5566224

5568548

5570453

5572223

5572224

5574976

5577267

5577268

5583520

5584054

5586146

D370016

D370463

D370672

D372237

D372481

D372703

D372896

D372919

D373585

D373764

D374013

D374014

D374227

D374424

D374872

D375732

D375733

D375734

D375932

D375935

D375952

D376127

D377792

D377934

D348880

D349273

D349701

D350113

D350348

D350349

D350350

D351375

D351840

D352497

D352503

D352946

D353131

D353361

D353587

D353588

D353591

D354055

D354062

D355181

D355895

D356084

D356309

D357224

D357249

D357457

D357680

D357681

D358148

D359052

D359734

5542103

5542106

5542116

5544250

5546275

5546380

5551078

5551627

D348427

D348470

D348665

D348666

D348668

D348674

D359735

D359959

D360398

D360632

D361070

D361763

D362840

D362852

D365094

D365817

D366872

D367640

D368479

D368696

D369162

5553137

5553376

5554996

5555550

5557743

5559471

5559522

5559806

5561436

D344271

D344444

D344511

D344512

D344945

D345977

D346785

D346786

D346798

D348071

D348250

5475752

5477192

5485506

5485513

5486843

5487184

5488649

5490177

5491739

5493198

D340906

D341589

D342248

D342663

D342729

D342730

D342741

D343173

D343615

D343616

D343834

D343835

D343836

D344087

5519303

5519346

5519506

5519777

5524276

5526398

5528666

5530399

5530922

5533119

5535258

5535434

5539360

5542016

5493700

5493714

5495206

5495208

5497126

5497382

5497383

5499273

5499394

5499397

5502437

5504494

5504812

5506490

5508709

5509048

5510693

5511235

5513078

5513996

Reference

D383748

D383749

D383759

D384080

D384662

D384951

D384952

D385271

D385283

D385555

D385873

D385874

D385875

D385877

D385888

D386175

D386494

D386757

D387054

D387055

D387199

D387346

D388078

D388079

D388080

D388081

D388082

D388424

D388429

D388430

D388775

D378366

D378911

D379558

D379624

D379981

D379982

D380468

D380751

D381021

D381664

D382537

D382538

D382872

D383115

D388783

D388793

D389157

D389476

D389478

D389488

D389641

D390221

D390222

D390509

D391567

D391955

D391966

D393470

D394256

D394423

D394425

D394433

D394438

D394439

D395301

D395302

D395431

D395642

D401554

D401929

D403265

D404397

D405080

D405782

D405801

D406098

D406191

D406586

D406695

D406812

D407063

D407685

D407708

D408401

D408402

D408418

D408783

D408815

D409186

D410459

D410460

D410929

D411165

D411196

D411202

D411204

D411507

D411535

D411843

D395875

D396472

D397337

D397689

D397694

D398926

D400161

D400165

D400204

D400209

D400496

D400526

D400527

D400874

D411844

D412000

D412487

D412709

D413893

D413898

D414159

D415122

D415499

D416226

D417224

D417449

D419155

D419290

D419565

PAT02250

63


Turn On / Turn Off

Place Call

Clear Entry

Automatic Redial

Receive Call

End Call

Lock Telephone

Quick Reference Card

Turn On and Off

PWR

Placing / Receiving Calls

Enter number, SND

Hold

CLR

CLR to clear all digits. Press and release

to clear one digit.

At system busy signal, attempt.

SND before ending call

SND

END

Locking / Unlocking

FCN , 5 (hold 5 until Loc?

appears, then

Unlock Telephone

Store Number

Recall Number

Emergency Dialing

Recall Last Number Called

Individual Call Timer

Resettable Call Timer

Enter three-digit unlock code.

If you make an error, END and enter again.

Memory Dialing

Phone number, STO , two digit location number.

Press RCL , then two digit location number.

Store emergency number in location 01. Hold to dial, even on locked unit.

RCL

1

Call Timers

RCL , ,

RCL , , ,

Cumulative Call Timer

Adjust Volume

RCL , , , ,

Volume Adjustments

Earpiece — press lower.

to raise. Press

Ringer — FCN described above.

and use and

Additional Features

Battery Voltage Meter

Display Own Phone Number

Mute

Access Feature Menu

RCL ,

While in a call,

6 .

FCN ,

FCN , 1

6

to

as

. To unmute, FCN ,


RBRC

SM

RBRC

Ni-Cd

THIS PACKAGE MAY CONTAIN A NICKEL CADMIUM BATTERY

WHICH MUST BE RECYCLED OR DISPOSED OF PROPERLY.

• Refer to the battery label for battery type.

• Recycling facilities may not be available in all areas.

• For additional information regarding disposal or recycling, call 1-800-331-6456 (in U.S.A.).

Pan American Cellular Subscriber Group

600 North U.S. Highway 45

Libertyville, Illinois 60048

1-800-331-6456 (in U.S.A.)

1-800-461-4575 (in Canada)

Please visit us at: www.mot.com

,

, , E•P, Turbo Dial, Super Speed Dial,

Ultra Saver, IntelliCharge, THE Cellular Connection, and

Performance Matched are registered trademarks of

Motorola, Inc.



1997 Motorola, Inc.

Printed in U.S.A.

68P09398A57-B

4/00 -SGS

No results