NOTICE. Shimano EW-EN100, DU-E6100, DU-E6100-CRG, DU-E6110, Shimano-Steps-6100

• Do not use alkaline or acidic cleaning agents for removing rust under any circumstances. If such cleaning agents are used, they may damage the chain and serious injury may result.

• Be sure to follow the instructions provided in the manuals when installing the product. It is recommended that you use SHIMANO genuine parts. Loose nuts or bolts and product damage may cause a sudden accident such as a fall and lead to serious injury.

Handling the battery

• If any liquid leaking from the battery gets into your eyes, immediately wash the affected area thoroughly with clean water such as tap water without rubbing your eyes, and seek medical advice immediately. If this is not done, the battery liquid may damage your eyes.

• Do not recharge the battery in places with high humidity or outdoors. Doing so may result in electric shock.

• Do not insert or remove the plug while it is wet. If this is not observed, electric shocks may result. If there is water leaking out of the plug, dry it thoroughly before inserting it.

• Do not subject this product to extremely low air pressure.

That can result in an explosion of the incorporated battery or the leakage of flammable liquid or gas from it.

Transporting this product by air is not a problem.

• Observe all federal, state and local environmental regulations when disposing of this product, because it incorporates a battery. Disposal of this product into fire or a hot oven, or mechanically crushing or cutting of it, that can result in an explosion of the incorporated battery.

• If the battery does not become fully charged even 2 hours after the designated charging time, immediately unplug the battery from the outlet and contact the place of purchase. Doing otherwise may cause overheating, bursting, or ignition of the battery. Refer to the battery charger user's manual for the designated charging time of the battery.

• Do not use the battery if it has any noticeable scratches or other external damage. Doing so may cause bursting, overheating or problems with operation.

• The operating temperature ranges for the battery are given below. Do not use the battery in temperatures outside these ranges. If the battery is used or stored in temperatures outside these ranges, fire, injury or problems with operation may occur.

1. During discharge: -10°C - 50°C

2. During charging: 0°C - 40°C

CAUTION

Riding precautions

• Observe the instructions in the user's manual for the bicycle, in order to ride safely.

Safety precautions

• Never modify the system. Doing so may cause a system error.

• Periodically check the battery charger and adapter, particularly the cord, plug, and case, for any damage. If the charger or adapter is broken, do not use it until it has been repaired.

• Use the product under the supervision of someone responsible for safety, and only as instructed.

Do not allow anyone (including children) with reduced physical, sensual, or mental capacity, or those without experience or knowledge, to use the product.

• Do not allow children to play near the product.

Handling the battery

• Do not leave the battery in a place exposed to direct sunlight, inside a vehicle on a hot day, or other hot places. This may result in battery leakage.

• If any leaked fluid gets on your skin or clothes, wash it off immediately with clean water. The leaked fluid may damage your skin.

• Keep away from children.

NOTICE

Safety precautions

• If any malfunctions or other problems occur, contact the place of purchase.

• Be sure to attach dummy plugs to any unused E-TUBE ports.

• For installation and adjustment of the product, consult a dealer.

• The components are designed to be fully waterproofed to withstand wet weather riding conditions. However, do not deliberately place them into water.

• Do not clean the bicycle with a high-pressure washer. If water gets into any of the components, operating problems or corrosion may result.

• Do not turn the bicycle upside down. There is a risk of damage to the cycle computer and switch unit.

3

• Handle the product carefully, and avoid subjecting it to any strong shocks.

• Although the bicycle still functions as a normal bicycle even when the battery is removed, the light does not turn on if it is connected to the electric power system. Be aware that using the bicycle under these conditions will be considered non-observance of the road traffic laws in

Germany.

• When charging the battery while it is mounted on the bicycle, be careful of the following:

- When charging, make sure there is no water on the charging port or the charger plug.

- Ensure that the battery is locked into the battery mount before charging.

- Do not remove the battery from the battery mount while charging.

- Do not ride with the charger mounted.

- Close the charging port cap when not charging.

- Stabilize the bicycle to ensure that it does not collapse during charging.

Handling the battery

• When you carry a power-assisted bicycle in a car, remove the battery from the bicycle and place the bicycle on a stable surface in the car.

• Before connecting the battery, make sure that there is no water collecting in the area where the battery will be connected (connector), and that it is not dirty.

• The use of a SHIMANO genuine battery is recommended.

If using a battery from another manufacturer, make sure to carefully read the manual thoroughly before use.

About used batteries

Disposal information for countries outside the European Union

This symbol is only valid within the

European Union. Follow local regulations when disposing of used batteries. If you are not sure, consult the place of purchase or a bicycle dealer.

Connection and communication with PC

A PC linkage device can be used to connect a PC to the bicycle (system or components), and E-TUBE PROJECT can be used to carry out tasks such as customizing single components or the whole system and updating firmware.

4

• PC linkage device: SM-PCE1/SM-PCE02

• E-TUBE PROJECT: PC application

• Firmware: software inside each component

Connection and communication with smartphone or tablet

It is possible to customize single components or the system, and update firmware, using E-TUBE PROJECT for smartphones/tablets after connecting the bicycle (system or components) to a smartphone or tablet via Bluetooth ® LE.

• E-TUBE PROJECT: app for smartphones/tablets

• Firmware: software inside each component

Care and maintenance

• The number found on the battery mount key is necessary when purchasing spare keys. Keep it in a safe place.

• Contact the place of purchase for updates of the product software. The most up-to-date information is available on the SHIMANO website. For details, refer to the

"Connection and communication with devices." section.

• Do not use thinner or other solvents to clean any of the products. As such substances may damage the surfaces.

• You should periodically wash the chainrings in a neutral detergent. In addition, cleaning the chain with neutral detergent and lubricating it can be an effective way of extending the useful life of the chainrings and the chain.

• Use a damp cloth, with the water well wrung out, when cleaning the battery and plastic cover.

• For any questions regarding handling and maintenance, contact the place of purchase.

• Products are not guaranteed against natural wear and deterioration from normal use and aging.

• For maximum performance we highly recommend

SHIMANO lubricants and maintenance products.

Assist

• If the settings are not correct, for instance if the chain tension is too tight, the proper assist force may not be obtained. If this happens, contact the place of purchase.

< DU-E6110 >

• This component is compatible with coaster brakes. If the crank is not installed in the correct position or the chain tension has not been correctly adjusted, contact the place of purchase, as there may not be proper assistance power.