USING THE REMOTE CONTROLLER. Panasonic CS-KE24NKU, CS-KE18NKU

10

REMOTE CONTROLLER (CONTINUED)

Temperature Display Selector button

This switches the temperature display between °C and °F.

Time Display Selector button This switches the time display between 24-hour time and 12-hour time.

ACL button (ALL CLEAR) Puts the remote controller into pre-operation status. Always press this button after replacing the batteries.

ADDRESS switch • The address switch changes to prevent mixing of signals from remote controller’s when two air conditioners are installed next to each other.

Normally, the address switch is set to A. For more information, please contact the dealer where you made the purchase.

• Normally, the tabs on the remote controller should not be bent.

NOTE The remote controller sends the temperature signal to the air conditioner regularly at five minute intervals.

If the signal from the remote controller stops for more than 15 minutes due to the loss of the remote controller or other trouble, the air conditioner will switch to the temperature sensor which is built into the indoor unit and control the room temperature. In these cases, the temperature around the remote controller may differ from the temperature detected at the air conditioner’s position.

USING THE REMOTE CONTROLLER

How to Install Batteries

ACL button

1.

Slide the cover in the direction indicated by the arrow and remove it.

2.

Install two AAA alkaline batteries. Make sure the batteries point in the direction marked in the battery compartment.

3.

Use a thin object such as the tip of a pen to press the ACL button.

CAUTION

• The batteries last about six months, depending on how much you use the remote controller. Replace the batteries when the remote controller’s display fails to light, or when the remote controller cannot be used to change the air conditioner’s settings.

• Use two fresh leak-proof type-AAA alkaline batteries.

• In replacing batteries, follow the instructions as mentioned in the sub-section “How to

Install Batteries”.

• If you do not use the remote controller more than 1 month, take out the batteries.

• Dispose of the used batteries at the designated location in compliance with the applicable local ordinances.

Information for Users on Collection and Disposal of Old Equipment and used Batteries

[Information on Disposal in other Countries outside the European Union]

These symbols are only valid in the European

Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved.

USING THE REMOTE CONTROLLER (CONTINUED)

How to Use the Remote

Controller

When using the remote controller, always point the unit’s transmitter head directly at the air conditioner’s receiver.

Air Conditioner

(Indoor unit)

Receiver

(Transmitter head)

Remote Controller

Remote Controller Installation

Position

The remote controller may be operated either from a non-fixed position or from a wall-mounted position. To ensure that the air conditioner operates correctly, do not install the remote controller in the following places:

• In direct sunlight

• Behind a curtain or other places where it is covered

• More than 26 ft (8 m) away from the air conditioner

• In the path of the air conditioner’s airstream

• Where it may become extremely hot or cold

• Where it may be subject to electrical or magnetic noise

• Where there is an obstacle between the remote controller and air conditioner

(since a check signal is sent from the remote controller every 5 minutes)

Mounting the Remote

Controller

Before mounting the remote controller, press the ON/OFF operation button at the mounting location to make sure that the air conditioner operates from that location. The indoor unit should make a beeping sound to indicate that it has received the signal.

Rear Side

Remote Control Holder

Press

Set in place Hole

Mounting Screws

5/32 x 5/8" (4 x 16 mm)

(included)

• To prevent loss of the remote controller, you can connect the remote controller to the holder by passing a string through the remote controller and attachment hole.

To take out the remote controller, pull it forward.

When Holding the Remote

Controller

• When using the remote controller and during air conditioner operation, the transmitter on the remote controller should be pointed towards the receiver on the indoor unit.

• Make sure that there are no objects between the remote controller and receiver which could block the signal.

11