Replacing the Paper Roll. Sharp XE-A307, XEA307


Add to my manuals
146 Pages

advertisement

Replacing the Paper Roll. Sharp XE-A307, XEA307 | Manualzz

Replacing the Paper Roll

Recording paper specifications

Be sure to use paper rolls specified by SHARP.

The use of any other paper rolls than specified could cause paper jamming, resulting in register malfunction.

Paper specification

Paper width:

Max. outside diameter: 80 mm

Quality:

57.5 ± 0.5 mm

High quality (0.06 to 0.08 mm thickness)

• Be sure to set a paper roll prior to using your machine, otherwise it may cause a malfunction.

Install the paper roll in the printer. Be careful then to set the roll and cut the paper end correctly.

(How to set the paper roll) (How to cut the paper end)

To the printer

To the printer

Incorrect Correct Correct Incorrect

Installing Paper Rolls

The register can print redeipts and journals. For the printer, you must install the paper rolls (receipt and journal paper rolls) provided with the register.

Print roller arm 1.

Remove the printer cover.

2.

Lift up the print roller arm of the receipt side.

3.

Set a paper roll in the paper roll cradle of the receipt side as per the diagram.

Paper positioning guides

4.

Feed the end of the paper along with the paper positioning guides as per the diagram.

5.

While holding down the paper, slowly close the print roller arm of the receipt side, and push down the arm until you hear a click locking the arm.

NOTE

If the print roller arm is not securely locked, printing is not done right. If this problem occurs, open the arm, and close the arm instructed above.

135

6.

Cut off the excess paper.

Print roller arm

7.

Lift up the print roller arm of the journal side.

8.

Set a paper roll in the paper roll cradle of the journal side as per the diagram.

9.

While holding down the paper, slowly close the print roller arm of the journal side, and push down the arm until you hear a click locking the arm.

Paper holding plate

Spool

Paper positioning guides

10.

Remove the paper holding plate from the spool.

Insert the end of the paper into the slit in the spool. (Press the journal paper feed key to feed more paper if required.)

Wind the paper two or three turns around the spool shaft.

136

11.

Mount the paper holding plate onto the take-up spool.

Set the spool on the bearing, and press the journal paper feed key to take up excess slack in the paper.

12.

Replace the printer cover.

13.

Press the receipt paper feed key to make sure the paper end comes out of the printer cover and clean paper appears.

NOTE

If the paper end does not come out, open the printer cover, and pass the paper end between the paper cutter and the paper guide of the printer cover, and replace the printer cover.

137

Replacing the paper roll

When colored dye appears on the edges of the paper roll, it is time to replace the paper roll.

Use paper of 57.5 ± 0.5 mm in width. To prevent jamming be sure to use paper specified by SHARP.

Replacing the receipt paper roll:

1.

Confirm that the REG mode has been selected.

2.

Remove the printer cover.

3.

Lift up the print roller arm of the receipt side.

4.

Remove the paper roll from the paper roll cradle of the receipt side.

NOTE

Do not pull the paper through the printer.

5.

Install a new paper roll correctly by following the steps in “Installing Paper Rolls”.

Replacing the journal paper roll:

1.

Confirm that the REG mode has been selected.

2.

Remove the printer cover.

3.

Press the journal paper feed key to advance the journal paper until its printed part is out of the way.

4.

Cut the paper and remove the take-up spool from the bearing.

NOTE

Do not pull the paper through the printer.

5.

Lift up the print roller arm of the journal side.

6.

Remove the paper roll from the paper roll cradle of the journal side.

7.

Remove the paper holding plate of the take-up spool.

8.

Remove the printed journal roll from the take-up spool.

9.

Install a new paper roll correctly by following the steps in “Installing Paper Rolls”.

Removing a Paper Jam

CAUTION: The paper cutter is mounted on the printer cover. Be careful not to cut yourself. Never touch the printer head immediately after printing, as the head may still be hot.

1.

Remove the printer cover.

2.

Lift up the print roller arm.

3.

Remove the paper jam. Check for and remove any shreds of paper that may remain in the printer.

4.

Reset the paper roll correctly by following the steps in “Installing Paper Rolls”.

138

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement

Table of contents