Guarantee: U.K. Miele FN 35402 i, FNS 37402 i, FNS 35402 i, FN 37402 i

Add to My manuals
84 Pages


Guarantee: U.K. Miele FN 35402 i, FNS 37402 i, FNS 35402 i, FN 37402 i | Manualzz

After Sales / Guarantee

In the event of a fault which you cannot correct yourself, or if the appliance is under guarantee please contact:

– your Miele Dealer or

– the Miele Service Department.

See end of this booklet for contact details. Please note that telephone calls may be monitored and recorded for training purposes and that a call-out charge will be applied to service visits where the problem could have been resolved as described in this booklet.

When contacting your Dealer or Miele, please quote the model and serial number of your appliance.

This information is given on the data plate inside your appliance.

Guarantee: U.K.

In the U.K. the appliance is guaranteed for 2 years from the date of purchase.

However, you must activate your cover by calling 0845 365 6640 or registering online at

Guarantee: Other countries

For information on the appliance guarantee specific to your country please contact Miele.

See end of this booklet for contact details.


Information for test institutes

All tests must be carried out according to relevant standards and directives .

In addition, the following information provided by the manufacturer must be observed:

– Loading instructions ,

The cool packs (depending on model) must be placed in the appliance in accordance with the loading instructions when determining the standard energy consumption and the storage time in the event of a fault .

– Information contained in the

Operating and installation instructions .


Information for dealers

Demo mode r

The appliance can be demonstrated in the showroom or at exhibitions in "demo mode". In this mode the controls and interior lighting work but the compressor remains switched off.


Place your finger on the

X sensor, and leave it there.

Activating demo mode

^ Switch the appliance off using the

On/Off sensor.

If this does not work, the safety lock is still activated.

The temperature will go out and the mains connection symbol t will appear in the display.

^ At the same time, briefly touch the

On/Off sensor (without letting go of the

X sensor).


Leave your finger on the

X sensor until the r symbol appears in the display.


Then release the

X sensor.

Demo mode is activated and the r symbol lights up in the display.


Information for dealers

Deactivating demo mode

The r symbol is lit up in the display.


Touch the

X or

Y sensor, until

0 appears (this means: demo mode is deactivated).

^ Touch the settings sensor.

All symbols available for selection appear in the display and the

0 symbol flashes.


Touch the sensors for setting the temperature (

X or


), repeatedly until the r symbol flashes.


Touch the OK sensor to confirm your selection.

The selected setting is applied, the r symbol flashes.

^ Touch the OK sensor to confirm your selection.

1 flashes in the display (this means: demo mode is activated), the r symbol lights up.


Touch the settings sensor to leave settings mode.

Otherwise the appliance exits settings mode automatically after approximately one minute.

Demo mode is deactivated, the r symbol goes out.


Electrical connection

Electrical connection U.K.

All electrical work should be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations

(BS 7671 in the UK).

The appliance is supplied with a mains cable and moulded plug ready for connection to an a.c. single phase

220-240 V 50 Hz supply.

Please ensure that the connection data quoted on the data plate match the household mains supply.

Connection should be made via a suitable switched socket which is easily accessible. It must not be located behind the appliance. For extra safety it is advisable to protect the appliance with a suitable residual current device


Do not connect the appliance to the mains electricity supply by an extension lead. Extension leads do not guarantee the required safety of the appliance

(e.g. danger of overheating).

This appliance must not be connected to the inverter of an autonomous power supply, e.g. a solar power system.

When switching the appliance on, a surge in power could trigger the safety cut-out mechanism. This could damage the electronic unit.

The appliance must not be used with so-called energy saving devices. These reduce the energy supply to the appliance which could then become too warm. Using such devices could alter the specification of the product.

If the connection cable has to be replaced, this must be done by a suitably qualified and competent person.

Do not plug other appliances in behind this appliance

Non-rewireable plugs (BS 1363)

The fuse cover must be re-fitted when changing the fuse, and if the fuse cover is lost, the plug must not be used until a suitable replacement is obtained. The colour of the correct replacement cover is that of the coloured insert in the base of the plug, or the colour that is embossed in words in the base of the plug (as applicable to the design of the plug fitted).

Replacement fuses should be ASTA approved to BS 1362 and have the correct rating. Replacement fuses and fuse covers may be purchased from your local electrical supplier.






Key Features

  • No icing up of food and no need to defrost thanks to Frost free
  • Optimum and maintenance-free LED lighting in compartment
  • Soft-closing doors thanks to SoftClose
  • Freezer compartment can be increased in size with-VarioRoom
  • Rapid and gentle freezing of food - Super freeze

Related manuals