Fitting the furniture door. Miele FN 35402 i, FNS 37402 i, FNS 35402 i, FN 37402 i

Add to My manuals
84 Pages

advertisement

Fitting the furniture door. Miele FN 35402 i, FNS 37402 i, FNS 35402 i, FN 37402 i | Manualzz

Installing the appliance

Fitting the furniture door

The furniture door must be at least of

16 mm thick and not exceed 19 mm thick.

The following gap dimensions must be maintained:

– The gap between the furniture door and the unit door above must be at least 3 mm.

– The vertical gap between furniture doors should also be about 3 mm.

The exact dimension will vary depending on the radius of the furniture door edges.

If fitted in a run of units make sure that the top edge of the furniture door is at the same height as neighbouring unit doors.

The furniture door must be fitted correctly and not under tension.

Fitting a door front which is heavier than the maximum permitted could damage the hinges. This can cause subsequent functional problems.

Before fitting furniture doors, ensure that the weight of the door does not exceed the maximum permitted:

Appliance

FN 35402 i

FN 37402 i

FNS 35402 i

FNS 37402 i

26

21

26

Maximum weight of furniture door in kg

21

When fitting large or divided furniture doors an extra fitting kit or set of fixing brackets is required. These are available to order from Miele.

76

Installing the appliance

Tip: Push fitting aids b together with the furniture front up to the height of the adjoining unit furniture doors.

^

A gap of 8 mm is set ex-works between the appliance door and the fixing bracket. Double check this gap and reset it if necessary.

^ Push fitting aids b up to the height of the furniture door: the lower edge X of the fitting aids must be at the same height as the upper edge of the furniture door being fitted (see on the diagram).

^ Undo nuts c and take fixing bracket d off together with fitting aids b

.

77

Installing the appliance

^

Place the furniture door with the outer side downwards on a stable surface.

^ Using a pencil, lightly mark a line down the centre of the inside of the furniture door e

.

^ Hang fixing bracket d with the fitting aids onto the inside of the furniture door. Align the fixing bracket centrally.

^ Attach the fixing bracket securely using at least 6 short chipboard screws f

. (On cassette doors only use 4 screws on the edges). Drill holes in the furniture door if necessary.

^ Pull the fitting aids upwards to remove them g . Turn them around and fit them into the middle slots on the fixing bracket for safe keeping.

^ Fit side cover q to the fixing bracket on the opposite side of the hinge.

^

Turn the furniture door over and attach the handle (if required).

78

^

Open the appliance door.

Installing the appliance

Aligning the door

^ Hang the furniture door onto adjusting bolts h .

^

Loosely attach nuts c on the adjusting bolts.

^

Close the door and check the distance between the door and neighbouring furniture doors. The gaps should be even.

– Side adjustments (X)

^

Slide the furniture door.

– Height adjustment (Y)

^

Use a screwdriver to adjust bolts h

.

A gap of 8 mm is set ex-works between the appliance door and the fixing bracket. This must only be adjusted within its permitted range.

79

Installing the appliance

^ Whilst counterholding adjusting bolts h with a screwdriver, tighten nuts c on the appliance door with ring spanner j .

^

Cover strip k must be completely hidden in the niche, and must not protrude.

^ Drill holes l in the furniture door and fit screws m

. Make sure the two metal edges are aligned (Symbol

II

).

^ Close the appliance door and the furniture door.

Aligning the door

– Depth adjustment (Z)

^

Loosen screws i at the top of the appliance door, and screw n on the fixing bracket at the bottom. By moving the furniture door, create a gap of 2 mm between the furniture door and the housing unit.

80

^

Tighten all screws again.

^

Replace top cover o

, and click it into place.

Installing the appliance

To make sure the appliance is correctly fitted:

– The doors must close properly.

– The doors must not touch the housing unit.

– The seal at the top edge of the handle side must fit properly.

^ To double check place a torch in the appliance and close the door.

Turn the lights out in the room. If you can see any light shining out from the sides double check the installation.

^

Replace side covers p

, making sure you hear them click into place.

81

82

83

FN 35402 i, FN 37402 i, FNS 35402 i, FNS 37402 i en - GB M.-Nr. 09 943 570 / 00

advertisement

Key Features

  • No icing up of food and no need to defrost thanks to Frost free
  • Optimum and maintenance-free LED lighting in compartment
  • Soft-closing doors thanks to SoftClose
  • Freezer compartment can be increased in size with-VarioRoom
  • Rapid and gentle freezing of food - Super freeze

Related manuals