Using the Remote Control. Sony KV-32HS500
Advertisement
Advertisement
Using the Remote Control
Overview
This chapter describes how to set up, program, and use the TV’s remote control.
Topic
Programming the Remote Control
Page
Inserting Batteries
1 Remove the battery cover from the remote control.
2 Insert two size AA (R6) batteries (supplied) by matching the e and E terminals on the batteries to the diagram inside the battery compartment.
3 Replace the battery cover.
1 2
✍
Remove the batteries to avoid damage from possible battery leakage whenever you anticipate that the remote control will not be used for an extended period. Handle the remote control with care. Avoid dropping it, getting it wet, placing it in direct sunlight, near a heater, or where the humidity is high.
39
Button Descriptions
Outside Panel
1
2
3
4
5
6
7
8
9 q;
Button
1 MUTING
MUTING
VCR/DVD SAT/CABLE
POWER
TV
TV/VIDEO
FUNCTION
VCR/DVD SAT/CABLE TV
PIC MODE ANT SLEEP DISPLAY
1
4
7
JUMP
8
0
2
5
3
6
9
ENTER
FLIP OPEN
DRC MODE FREEZE FAVORITES MTS/SAP qa qs qd qf qg
VOL MENU CH wa
MEMORY STICK
CODE SET AV 1 2 3 DVD RM -Y186 ws wd qh qj qk ql w;
2 TV/VIDEO
3 PIC MODE
4 ANT
5 JUMP
6 DRC MODE
7
8 VOL +/-
9
TV
0 CODE SET qa POWER
Buttons qs FUNCTION
Buttons
Description
Press to mute the sound. Press again or press VOL+ to restore the sound.
Press repeatedly to cycle through the video equipment connected to the TV’s video inputs.
Press repeatedly to cycle through the available video picture modes: Vivid, Standard, Movie, Pro . Also available
in the Video Menu. For details, see “Selecting Video
Press to switch between the sources connected to the
TV’s VHF/UHF and AUX inputs.
Press to jump back and forth between two channels.
The TV alternates between the current channel and the last channel that was selected.
Press repeatedly to cycle through the available highresolution picture modes: Interlaced, Progressive,
CineMotion . Also available in the Video Menu. For
details, see “Selecting Video Options” on pages 62-63.
Press to turn on and off Twin View. For details, see
Press to adjust the volume.
Move the joystick Vv B b to move the on-screen cursor. To select an item, press the center of the joystick ( ).
Press to program the remote control to operate non-
Sony video equipment. For details, see “Programming the Remote Control” on page 43.
VCR/DVD: Press to turn on and off the VCR or DVD player.
SAT/CABLE: Press to turn on and off the satellite receiver or cable box.
TV: Press to turn on and off the TV.
The indicator lights up momentarily when pressed to show which equipment the remote control is operating:
VCR/DVD: Press to have the remote control operate the
VCR or DVD player.
SAT/CABLE: Press to have the remote control operate the satellite receiver or cable box.
TV: Press to have the remote control operate the TV.
40
Button qd DISPLAY qf qg
SLEEP
0 - 9
ENTER
Description
Press once to display the current channel number and current time and channel label (if set). Press again to turn Display off.
Press repeatedly until the TV displays the time in minutes (15, 30, 45, 60, or 90) that you want the TV to remain on before shutting off automatically. To cancel press until Sleep Off appears. While the Sleep feature is set, press once to display the remaining time.
Press 0 - 9 to select a channel; the channel changes after
3 seconds. Press ENTER to change channels immediately.
qh qj qk ql w;
FAVORITES
MTS/SAP
FREEZE
MENU
Press to display the Favorite Channels list. For details,
Press repeatedly to cycle through the Multi-channel
TV Sound (MTS) options: Stereo, Auto SAP (Second
Audio Program), and Mono .
Also available in the
Audio Menu. For details, see “Using the Audio Menu” on page 64.
Press to freeze the picture. Press again to restore the
picture. For details, see page 50.
Press repeatedly to step through the Audio Effect options. Also available in the Audio Menu. For details,
Press to display the Menu. Press again to exit from the
Menu. For details, see “Using the Menus” on page 61.
wa CH +/Press to scan through channels. To scan quickly through channels, press and hold down either CH button.
ws MEMORY STICK Press to display the Memory Stick Menu. For details,
see “Using the Memory Stick Picture Viewer” on page 51.
wd
AV 1 2 3 DVD
Use the A/V slide switch to control connected video equipment. You can program one video source for
each switch position. For details, see “Programming the Remote Control” on page 43.
41
wf wg wh wj wk wl
Inside Panel
MUTING
VCR/DVD SAT/CABLE POWER
TV
TV/VIDEO VCR/DVD
TV/VCR
DISPLAY
FUNCTION
SAT/CABLE
TV
GUIDE
SYSTEM
OFF
REC
DISC MENU
DVD TITLE MENU
RESET
PIC MODE SLEEP
DRC MODE
FREEZE FAVORITES
MTS/SAP
VOL
MENU CH
CODE SET
MEMORY STICK
AV 1 2 3 DVD
RM -Y186
TV
MUTING
VCR/DVD SAT/CABLE
POWER
TV
TV/VIDEO
FUNCTION
VCR/DVD SAT/CABLE TV
TV/VCR DISPLAY GUIDE
SYSTEM
OFF
REC
DISC MENU DVD TITLE MENU
RESET PIC MODE SLEEP e; ea es ed ef eg eh
To access the inside panel, open the outside cover as shown.
Button wf TV/VIDEO wg TV/VCR wh DISPLAY wj DISC MENU wk DVD TITLE wl RESET e; FUNCTION
Buttons ea SYSTEM OFF es GUIDE ed Transport
Buttons ef MENU eg SLEEP eh PIC MODE
Description
Press repeatedly to cycle through the video equipment connected to the TV’s video inputs.
Press to change the VHF/UHF output of the VCR.
Press once to display the current channel number and current time and channel label (if set). Press again to turn Display off.
Press to display the DVD Menu.
Press to display the DVD Title.
Press to reset the settings to the factory defaults. See
pages 62 and 64. Also used to clear Favorite Channels
The indicator lights up momentarily when pressed to show which equipment the remote control is operating:
VCR/DVD: Press to have the remote control operate the
VCR or DVD player.
SAT/CABLE: Press to have the remote control operate the satellite receiver or cable box.
TV: Press to have the remote control operate the TV.
Press to turn off all Sony brand audio/video equipment at once. (May not function with older Sony equipment.)
Press to display the program guide of your satellite program provider.
m Rewind
N Play z Record (press together with N ) x Stop
M Fast forward
X Pause
Press to display the DVD setup menu.
Press repeatedly until the TV displays the time in minutes (15, 30, 45, 60, or 90) that you want the TV to remain on before shutting off automatically. To cancel press until Sleep Off appears. While the Sleep feature is set, press once to display the remaining time.
Press repeatedly to cycle through the available video picture modes: Vivid, Standard, Movie, Pro . Also available in
the Video Menu. For details, see “Selecting Video
42
Programming the Remote Control
The remote control is preset to operate Sony brand video equipment.
Sony Equipment
Beta, Ed Beta VCRs
8 mm VCR
VHS VCR
DVD player
Switch Position on
Remote Control
AV1
AV2
AV3
DVD
Programmable Code
Number
303
302
301
751
If you have video equipment other than Sony brand that you want to control with the TV’s remote control, use the following procedure to program the remote control.
✍
The equipment must have infrared (IR) remote capability in order to be used with the remote control.
z
❑ If more than one code number is listed, try entering them one by one until you come to the correct code for your equipment.
❑ If you enter a new code number, the code number you previously entered at that setting is erased.
❑ In some cases, you may not be able to operate your equipment with the supplied remote control. In such cases, use the equipment’s own remote control unit.
❑ Whenever you remove the batteries to replace them, the code numbers may revert to the factory setting and must be reset.
1
Turn to the list of “Manufacturer’s Codes” on page 44, and find
the three-digit code number for the manufacturer of your equipment. (If more than one code number is listed, use the number listed first.)
2 Set the A/V slide switch to 1, 2, 3 , or DVD .
3 Press CODE SET.
4 Press the FUNCTION button for the type of equipment you want to control with the TV’s remote control ( VCR/DVD FUNCTION or SAT/CABLE
FUNCTION ).
5 Enter the three-digit manufacturer’s code number.
6 Press ENTER .
✍
You must do step 6 within 10 seconds of step 5, or you must redo steps 3 through 6.
7 To check if the code number works, aim the TV’s remote control at the equipment and press the POWER button that corresponds with that equipment. If it responds, you are done. If not, try using another code listed for that manufacturer.
43
Manufacturer’s Codes
VCRs
Manufacturer Code
Sony
Admiral
(M. Ward)
Aiwa
Audio
Dynamic
301, 302, 303
327
338, 344
314, 337
Broksonic
Canon
Citizen
Craig
319, 317
309, 308
332
302, 332
Criterion 315
Curtis Mathes 304, 338, 309
Daewoo
DBX
Dimensia
341, 312, 309
314, 336, 337
304
Emerson 319, 320, 316,
317, 318, 341
Fisher
Funai
General
Electric
Go Video
Goldstar
Hitachi
330, 335
338
329, 304, 309
322, 339, 340
332
306, 304, 305,
338
Instant Replay 309, 308
JC Penney 309, 305, 304,
330, 314, 336,
337
JVC
Kenwood
LXI (Sears)
Magnavox
Marantz
Marta
314, 336, 337,
345, 346, 347
314, 336, 332,
337
332, 305, 330,
335, 338
308, 309, 310
314, 336, 337
332
Memorex
Minolta
Mitsubishi/
MGA
Multitech
NEC
Olympic
Optimus
309, 335
305, 304
323, 324, 325,
326
325, 338, 321
314, 336, 337
309, 308
327
44
Manufacturer
Orion
Panasonic
Pentax
Philco
Philips
Pioneer
Quasar
RCA/
PROSCAN
Realistic
Sansui
Samsung
Sanyo
Scott
Sharp
Signature
2000 (M.
Ward)
SV2000
Sylvania
Symphonic
Tashiro
Tatung
Teac
Technics
Toshiba
Wards
Yamaha
Zenith
338
308, 309, 338,
310
338
332
314, 336, 337
314, 336, 338,
337
309, 308
312, 311
327, 328, 335,
331, 332
314, 330, 336,
337
331
Laserdisc Players
Manufacturer
Sony
Panasonic
Pioneer
Code
701
704, 710
702
Code
317
308, 309, 306,
307
305, 304
308, 309
308, 309, 310
308
308, 309, 306
304, 305, 308,
309, 311, 312,
313, 310, 329
309, 330, 328,
335, 324, 338
314
322, 313, 321
330, 335
312, 313, 321,
335, 323, 324,
325, 326
327, 328
338, 327
DVD Players
Manufacturer Code
Sony
General
Electric
Hitachi
JVC
Magnavox
Mitsubishi
Oritron
Panasonic
751
755
Philips
Pioneer
757
752
RCA/Proscan 755
Samsung 758
Toshiba 754
Zenith 760
758
756
757
761
759
753
Cable Boxes
Manufacturer Code
Sony 230
Hamlin/Regal 222, 223, 224,
Jerrold/G. I.
225, 226
201, 202, 203,
204, 205, 206,
Oak
Panasonic
207, 208, 218
227, 228, 229
219, 220, 221
Pioneer
Scientific
Atlanta
Tocom
Zenith
214, 215
209, 210, 211
216, 217
212, 213
Satellite Receivers
Manufacturer Code
Sony 801
Dish Network 810
Echostar 810
General
Electric
Hitachi
802
805
Hughes
Mitsubishi
Panasonic
RCA/
PROSCAN
Toshiba
804
809
803
802, 808
806, 807

Public link updated
The public link to your chat has been updated.
Advertisement