operating the cleaner. Samsung SC20F70HC, VC12F70HNKC

operating the cleaner

POWER CORD

CAUTION

• When removing the plug from the electrical outlet, grasp the plug, not the cord.

ON/OFF SWITCH operating the cleaner _09

POWER CONTROL

Hose Handle (SC20F70H Series)

1. ON/OFF [   ] Button

- Press the ON/OFF button to operate the vacuum cleaner.

Press again to stop the vacuum cleaner.

2. [(-/+)] Button

- Press the MODE button repeatedly to select the correct mode.

(ON) MIN → MAX

3. [   ] Button

- Press the [   ] button to operate the vacuum cleaner quietly.

Don’t cover the handle transmitter when you use a handle control button.

-/+ sender

Handle Control

The cleaner is controlled by radio frequency signals.

HOSE (SC07F70H Series)

1. ON/OFF [   ] Button

- Press the ON/OFF button to operate the vacuum cleaner.

Press again to stop the vacuum cleaner.

2. [(-)], [(+)] Button

- Press the (+) button to increase the vacuum's suction power.

Press the (-) button to decrease the vacuum's suction power.

Don’t cover the handle transmitter when you use a handle control button.

If no button is pressed for 30 minutes while cleaning, the safety device is activated and the power is cut off.

In this case, press the [Power] button on the main unit or unplug and then plug the power cord in again.

- + sender

Handle Control

The cleaner is controlled by radio frequency signals.

HOSE (SC20F70U Series)

1. ON/OFF [   ] Button

- Press the [   ] button to operate the vacuum cleaner. Press again to stop the vacuum cleaner.

2. [SUCTION (-/+)] Button

- Press the [SUCTION (-/+)] button to increase or decrease the suction power. Each time you press the button, you gradually increase the suction power. After the suction power reaches its maximum, the next time you press the button, you return the suction power to its minimum.

3. [BRUSH ON/OFF] Button

- Press the [BRUSH ON/OFF] button to operate the UV Brush.

Press again to stop the UV Brush.

sender

Handle Control

The cleaner is controlled by radio frequency signals.

Don’t cover the handle transmitter when you use a handle control button.

If no button is pressed for 30 minutes while cleaning, the safety device is activated and the power is cut off.

In this case, press the [Power] button on the main unit or unplug and then plug the power cord in again.

10_ operating the cleaner

operating the cleaner

Change the battery

• When the vacuum cleaner does not work, replace the batteries.

If the problem persists, please contact our authorized dealer.

• Use 2 batteries of size AAA.

CAUTION

1. Never disassemble or recharge the batteries.

2. Never heat up the batteries or throw them into a fire.

3. Do not reverse (+), (-) poles.

4. Dispose of the batteries property.

BATTERY TYPE : AAA Size

BODY

Press the power ON/OFF button repeatedly to start and to stop the vacuum cleaner. (OFF → ON → OFF)

If the remote handle control is not working, the cleaner can be operated using the ON/OFF button on the body of the machine.

1





The ON/OFF button toogles the vacuum between the on and off states.

The filter light is illuminated when the dust pack requires checking or emptying.

Before performing this operation, make sure that there is no blockage in the tube, hose or brush.

2 operating the cleaner _11

USING THE UV BRUSH (SC20F70U SERIES)

1. Insert the brush into the hose handle.

• Insert the UV brush securely into the hose handle until you hear a “clicking” sound.

2. Press the [BRUSH ON/OFF] button to start cleaning.

• Press the [BRUSH ON/OFF] button and choose the appropriate suction strength for the cleaner.

• It is advisable to select the (Max) suction strength setting.

• UV sterilization cannot be activated by itself.

3. When you have finished UV cleaning, press the [   ] button.

• Press the [   ] button to stop the cleaner.

- For safety reasons, UV brushing only runs for 30 minutes and then stops operating. To resume the operation, press the [SUCTION (-/+)] button again.

CAUTION

The UV brush, which is inserted into the hose handle (not directly connected to the telescopic pipe), is dedicated for bedclothes.

12_ operating the cleaner

operating the cleaner

USING THE DUST SENSOR (OPTION)

Dust Sensor Operations

• Indicates the amount of sucked in dust so that users can experience the successful operation of the product while cleaning the room.

• Green : When the amount of sucked in dust is small.

• Red : When the amount of sucked in dust is large.

• The dust sensor is automatically turned on when the cleaner runs and turned off when the cleaner is stopped.

• Since the dust sensor runs on battery power, there is no separate switch.

Installing the Batteries

1 2 Check the polarities 3

• If the dust sensor doesn’t work even after cleaning the sensor, replace the batteries with new ones.

AAA type batteries are required.

CAUTION

• Do not disassemble or recharge the used batteries.

• Do not heat the batteries or put them in a fire.

• Check the polarities (+ ,-) before inserting the batteries.

• Put the used batteries into the battery recycle bin.

• When you are not using the product for an extended period of time, separate the batteries.

operating the cleaner _13

Cleaning the dust sensor (Option)

• Since the dust sensor consists of sensitive electronic devices, if water or other liquids enters the sensor, it may cause a problem.

• If you use athe dust sensor without closing the battery compartment cover, pollutants such as dust may accumulate in the compartment and cause a problem. Therefore, be sure to use the product with the compartment cover closed.

• Take care when you use the cleaner because the dust sensor may malfunction or may break due to an impact. Dust Sensor (2 EA)

Installing the Dust Sensor

• Assemble the dust sensor between the air inlet connector on the neck of the brush and the extension pipe. (Recommended)

You can assemble the dust sensor between the extension pipe and the hose.

The assembly position of the dust sensor

14_ operating the cleaner