tools and maintenance filter. Samsung SC20F70HC, VC12F70HNKC

tools and maintenance filter

USING ACCESSORY

Pipe

• Adjust the length of the telescopic pipe by sliding the length control button located in the center of the telescopic pipe back and forth.

• To check for blockages, separate the telescopic pipe and adjust to shorten. This allows for easier removal of waste clogging the tube.

Accessory (Option)

• Pull out the button, to use the dusting brush.

• To use the crevice tool, push the accessory on to the end of the hose handle in the opposite direction.

tools and maintenance filter _15

Accessories (SC20F70U Series)

• Push the accessory onto the end of the hose handle.

• Pull out the dusting brush to use the crevice tool.

• Push the accessory onto the end of the pipe.

• Pull out the dusting brush to use the crevice tool.

Accessory (Option)

• Furniture brush for desk, Furniture and Floor.

16_ tools and maintenance filter


MAINTAIN FLOOR TOOLS

2-Step Brush

Carpet Cleaning

• Adjust the inlet lever according to the floor surface.

• Remove waste matter completely if the inlet is blocked.

Power Pet Plus Brush (Option)

1 2

Floor Cleaning

3

For improved pickup of pet hair and fibre on carpets.

4 5 6

Frequent vacuuming of hair or pet fur may cause a falling-off of the rotation due to matters tangled around the drum. In this case, clean the drum with care.

1. Push the Open button of the transparent screen cover to separate the cover.

2. Remove the brushbar from the transparent screen.

3. Remove waste matter such as dust and hair tangled around the brushbar using scissors.

4. Remove dust inside the brush housing using a dry duster or crevice tool.

5. Insert brushbar into rotating belt and assemble.

6. Click the transparent screen cover back into place to reassemble.

Parquet Master Brush (Option)

• Vacuum dust in wide area at once.

• Remove waste matter completely if the inlet is blocked.


Mini turbo brush (Option)

- To replace brushroll

1. If a clog is present or debris is visible, unscrew the two screws on the back of the Mini turbo brush to remove the faceplate and clear any obstructions.

2. Inspect condition of brushroll.

Replace brushroll if brushes are worn down.

To remove brushroll, pull up and out of end slots in nozzle housing.

Insert ends of brushroll into same slots to replace.

Inspect belt to ensure that it is in good condition.

If belt is broken or cracked, replace belt according to To Replace

Belt instructions.

3. Using at MAX.

Press the MAX button to operate the vacuum at maximum intake.

- To replace belt

1. Remove bottom plate.

See figure in To Replace Brushroll instructions.

2. Loop one end of new belt around shaft of pulley.

3. Loop other end of belt around designated area for it on brushroll.

Insert brushroll into slots in nozzle housing.

See figure in To Replace Brushroll instructions.

4. Fit Mini turbo brush back together as described in To Replace

Brushroll instructions.



To remove dust from the dust bin of the UV brush (Option)

When you notice that the dust bin is filled, use the [Dust Removal] button to empty the dust bin.

1. To remove dust from the dust bin, move the [Dust Removal] button to the “Open” position.

- While the cleaner is operating (suction), use the [Dust Removal] button for this purpose.

2. When done, move the [Dust Removal] button to the “Close” position.

- When the [Dust Removal] button is in the “Open” position, the suction power of the cleaner is reduced.

Cleaning the UV brush (Cleaning the drum) (Option)

Human and pet hair often becomes tangled in the drum, causing a reduction in the rotary power of the the drum. To prevent this, clean the drum on a regular basis. Before the operations make sure that UV brush is off.

1. Push the [Open Transparent Cover] button inward to remove the cover.

2. Use the crevice tool to remove impurities such as dust and hair from around the drum.

3. When done, push the [Open Transparent Cover] button outward to close the cover.


CLEANING THE DUST SENSOR (OPTION)

If the green light is not lit while cleaning

• Check if the hose, extension pipe or the air inlet is clogged and clean it if necessary.

• Empty the dust bin of the cleaner or clean the filters.

If the red light does not light up when cleaning a dusty location

• Clean the sensors (2EA) in the dust sensor block with a dry cloth.

CAUTION

Take care when you clean the sensors in the dust sensor block so that the sensors are not damaged.

EMPTYING THE DUST BIN

1 2 3

Once dust reaches the dust full mark, empty the dust bin.

4

Take the dust bin out by lifing the handle

5

Push the button aside.

6

Click

Throw the dust away in the bin.

Close the dust bin cover.

Before use, push the dust bin into the main body of the vacuum cleaner until you hear the “click” sound.



CLEAN THE GRILLE

1 2 3


4

Turn the grille and take out it.

5

Brush away the dust.

Insert the grille back into the dust bin and turn the grille.



CLEAN THE DUST BIN WITH WATER

1 2 3


4

Turn the grille and take out it.

5

Push the button.

6

Separate the dust bin from body.

Clean the dust bin and body with water.

Leave the dust bin and body in the shade until completely dry.

You may rinse the dust bin with cold water.



CLEANING THE DUST FILTER

When to clean the dust filter

• If the dust filter is very dirty outside or clogged with fine dust, then clean it.

• The lamp will turn red when suction is reduced. If the light comes on after emptying the dust bin, cleaning the grill, please check the dust filter.

When suction is noticeably reduced or vacuum cleaner abnormally overheats, please clean the dust filter.


CLEANING THE DUST FILTER

1 2 3

Take the dust bin out by lifing the handle.

4

Pull the dust bin cover to open.

5

Remove the filter from the dust bin.

6

Shake the filter over a garabage can to remove loose dust, then wash the filter with water.

7

Let the filter dry in the shade for more than 12 hours.

Put the filter into the dust bin.

8


To close the dust bin cover, filter should be assembled.

After the take the dust bin in main body, close the cover dust when you hear the " click" sound.

Make sure the filter is completely dry before putting it back into the vacuum cleaner. Allow 12 hours for it to dry.

Do not use wet filter.

If dust filter is damaged or deformed please replace it.


CLEANING THE OUTLET FILTER

1 2 3

Take the dust bin out by lifing the handle.

4

Pull out the HEPA filter.

5

Separate the filter and holder by pulling.

6

Throw away the dirty filter.

Assemble the new filter in holder.

Assemble the filter and holder in main body.

• When suction is noticeably reduced continuously or vacuum cleaner abnormally overheats, please clean the outlet filter. Note. Do not wash HEPA filter.

If cleaning does not resolve the problem Please replace blocked out filter.

• Replacement filters are available at your local Samsung distributor.


tools and maintenance filter. Samsung SC20F70HC, VC12F70HNKC

tools and maintenance filter

tools and maintenance filter