Chapter 4. Introduction to DigiCell. MSI MS-7125 v3.0

Add to my manuals
120 Pages

advertisement

Chapter  4. Introduction to  DigiCell. MSI MS-7125 v3.0 | Manualzz

BIOS Setup

Chapter 3. BIOS Setup

BIOS Setup

This chapter provides information on the BIOS Setup program and allows you to configure the system for optimum use.

You may need to run the Setup program when:

² An error message appears on the screen during the system booting up, and requests you to run SETUP.

² You want to change the default settings for customized features.

MSI Reminds You...

1. The items under each BIOS category described in this chapter are under c ontinuous update for better s y s tem performanc e.

Therefore, the description may be slightly different from the latest

BIOS and should be held for reference only.

2. While booting up, the BIOS version is shown in the 1st line appearing after the memory counting. It is usually in the format: example: W7125NMS V1.0B32 061704 where:

1st digit refers to BIOS maker as A=AMI(R); W=AWARD(R)

2nd - 5th digit refers to the model number.

6th digit refers to nVIDIA chipset.

7th - 8th digit refers to the customer, MS=all standard customers.

V1.0 refers to the BIOS version.

061704 refers to the date this BIOS is released.

3-1

M S-7125 ATX M ainboard

Entering Setup

Power on the computer and the system will start POST (Power On Self Test) process.

W hen the message below appears on the screen, press <DEL> key to enter Setup.

Press DEL to enter SETUP

If the message disappears before you respond and you still wish to enter Setup, restart the system by turning it OFF and On or pressing the RESET button. You may also restart the system by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys.

Selecting the First Boot Device

You are allowed to select the 1st boot device without entering the BIOS setup utility by pressing <F11>. When the same message as listed above appears on the screen, press <F11> to trigger the boot menu.

The POST messages might pass by too quickly for you to respond in time. If so, restart the system and press <F11> after around 2 or 3 seconds to activate the boot menu similar to the following.

Floppy

IDE-0

CDROM

[Up/Dn] Select

Select First Boot Device

: 1st Floppy

: IBM-DTLA-307038

: ATAPI CD-ROM DRIVE 40X M

[RETURN] Boot [ESC] cancel

The boot menu will list all the bootable devices. Select the one you want to boot from by using arrow keys, then press <Enter>. The system will boot from the selected device. The selection will not make changes to the settings in the BIOS setup utility, so next time when you power on the system, it will still use the original first boot device to boot up.

MSI Reminds You...

The items under each BIOS category described in this chapter are under continuous update for better system performance. Therefore, the description may be slightly different from the latest BIOS and should be held for reference only.

3-2

BIOS Setup

Control Keys

<

>

<

>

<

>

<

>

<Enter>

<Esc>

<+/PU>

<-/PD>

<F5>

<F7>

<F10>

Move to the previous item

Move to the next item

Move to the item in the left hand

Move to the item in the right hand

Select the item

Jumps to the Exit menu or returns to the main menu from a submenu

Increase the numeric value or make changes

Decrease the numeric value or make changes

Previous Values

Load Optimized Defaults

Save all the CMOS changes and exit

Getting Help

After entering the Setup menu, the first menu you will see is the Main Menu.

M ain M enu

The main menu lists the setup functions you can make changes to. You can use the arrow keys (

↑↓ ) to select the item. The on-line description of the highlighted setup function is displayed at the bottom of the screen.

Sub-M enu

If you find a right pointer symbol (as shown in the right view) appears to the left of certain fields that means a sub-menu can be launched from this field. A submenu contains additional options for a field parameter. You can use arrow keys (

↑↓ )

to highlight the field and press <Enter> to call up the sub-menu. Then you can use the control keys to enter values and move from field to field within a sub-menu. If you want to return to the main menu, just press the <Esc >.

General Help <F1>

The BIOS setup program provides a General Help screen. You can call up this screen from any menu by simply pressing <F1>. The Help screen lists the appropriate keys to use and the possible selections for the highlighted item. Press <Esc> to exit the

Help screen.

3-3

M S-7125 ATX M ainboard

The Main Menu

Once you enter Phoenix-Award

®

BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from twelve setup functions and two exit choices. Use arrow keys to select among the items and press

<Enter> to accept or enter the sub-menu.

3-4

Standard CMOS Features

Use this menu for basic system configurations, such as time, date etc.

Advanced BIOS Features

Use this menu to setup the items of AWARD

®

special enhanced features.

Advanced Chipset Features

Use this menu to change the values in the chipset registers and optimize your system ’ s performance.

Integrated Per ipher als

Use this menu to specify your settings for integrated peripherals.

Power M anagement Setup

Use this menu to specify your settings for power management.

PNP/PCI Configurations

This entry appears if your system supports PnP/PCI.

H/W Monitor

Use this menu to specify your settings for hardware.

Cell M enu

Use this menu to specify your settings for CPU/AGP frequency/voltage control and overclocking.

BIOS Setup

Load Optimized Defaults

Use this menu to load the BIOS values for the best system performance, but the system stability may be affected.

BIOS Setting Password

Use this menu to set the password for BIOS.

Save & Exit Setup

Save changes to CMOS and exit setup.

Exit Without Saving

Abandon all changes and exit setup.

3-5

M S-7125 ATX M ainboard

Standard CMOS Features

The items in Standard CMOS Features Menu includes some basic setup items.

Use the arrow keys to highlight the item and then use the <PgUp> or <PgDn> keys to select the value you want in each item.

3-6

Date

This allows you to set the system to the date that you want (usually the current date).

The format is <day><month> <date> <year>.

day Day of the week, from Sun to Sat, determined by

BIOS. Read-only.

mon th date year

The month from Jan. through Dec.

The date from 1 to 31 can be keyed by numeric function keys.

The year can be adjusted by users.

T im e

This allows you to set the system time that you want (usually the current time). The time format is <hour> <minute> <second>.

IDE Primary/Secondary M aster/Slave

Press PgUp/<+> or PgDn/<-> to select [Manual], [None] or [Auto] type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. If your hard disk drive type is not matched or listed, you can use [Manual] to define your own drive type manually.

If you select [Manual], related information is asked to be entered to the following items. Enter the information directly from the keyboard. This information should be provided in the documentation from your hard disk vendor or the system manufacturer.

Access M ode

Capacity

Cylinder

The settings are CHS, LBA, Large, Auto.

The formatted size of the storage device.

Number of cylinders.

BIOS Setup

Head

Pr eco mp

Landing Z one

Sector

Number of heads.

W rite precompensation.

Cylinder location of the landing zone.

Number of sectors.

Drive A

This item allows you to set the type of floppy drive installed. Available options: [None],

[360K, 5.25 in.], [1.2M, 5.25 in.], [720K, 3.5 in.], [1.44M, 3.5 in.], [2.88M, 3.5 in.].

Halt On

The setting determines whether the system will stop if an error is detected at boot.

Available options are:

[All Errors]

[No Errors]

[All, But Keyboard]

[All, But Diskette]

[All, But Disk/Key]

The system stops when any error is detected.

The system doesn ’ t stop for any detected error.

The system doesn ’ t stop for a keyboard error.

The system doesn ’ t stop for a disk error.

The system doesn

’ t stop for either a disk or a keyboard error.

System Information

Press <Enter> to enter the sub-menu and the following screen appears:

CPU Type/BIOS Version/System M emory/Total Memory

The items show the CPU type, BIOS version and memory status of your system (read only).

3-7

M S-7125 ATX M ainboard

Advanced BIOS Features

3-8

Quick Boot

Setting the item to [Enabled] allows the system to boot within 5 seconds since it will skip some check items. Available options: [Enabled], [Disabled].

Boot To OS/2

This allows you to run the OS/2 ® operating system with DRAM larger than 64MB.

W hen you choose [No], you cannot run the OS/2

®

operating system with DRAM larger than 64MB. But it is possible if you choose [Yes].

IOAPIC Function

This field is used to enable or disable the APIC (Advanced Programmable Interrupt

Controller). Due to compliance with PC2001 design guide, the system is able to run in

APIC mode. Enabling APIC mode will expand available IRQ resources for the system.

Settings: [Enabled], [Disabled].

M PS Table Version

This field allows you to select which MPS (Multi-Processor Specification) version to be used for the operating system. You need to select the MPS version supported by your operating system. To find out which version to use, consult the vendor of your operating system. Settings: [1.4], [1.1].

Full Screen LOGO Display

This item enables you to show the company logo on the bootup screen. Settings are:

[Enabled]

[Disabled]

Shows a still image (logo) on the full screen at boot.

Shows the POST messages at boot.

Boot Sequence

Press <Enter> to enter the sub-menu and the following screen appears:

BIOS Setup

1st/2nd/3rd Boot Device

The items allow you to set the sequence of boot devices where BIOS attempts to load the disk operating system.

Boot Other Device

Setting the option to [Enabled] allows the system to try to boot from other device if the system fails to boot from the 1st/2nd/3rd boot device.

Hard Disk Boot Priority

Press <Enter> to enter the sub-menu. Then you may use the arrow keys (

↑↓ ) to select the desired device, then press <+>, <-> or <PageUp>, <PageDown> key to move it up/down in this hard disk boot priority list.

3-9

M S-7125 ATX M ainboard

Advanced Chipset Features

DRAM Configuration

Press <Enter> to enter the sub-menu and the following screen appears:

3-10

Timing M ode

This field has the capacity to automatically detect all of the DRAM timing. If you set this field to [Manual], the following fields will be selectable. The settings are:

[Auto], [Manual].

M emclock index value (M hz)

W hen the Timing Mode is set to [Manual], user can place an artificial memory clock on the system. Please note that memory is prevented from running faster than this frequency. Setting options: [100], [120], [133], [140], [150], [166], [180]

[200].

BIOS Setup

CAS# Latency (Tcl)

W hen the Timing Mode is set to [Manual], the field is adjustable.This controls the CAS latency, which determines the timing delay (in clock cycles) before

SDRAM starts a read command after receiving it. Settings: [Auto], [CL=2.0],

[CL=2.5], [CL=3.0]. [CL=2.0] increases the system performance the most while

[CL=3.0] provides the most stable performance.

Min RAS# Active Time (Tras)

W hen the Timing Mode is set to [Manual], the field is adjustable. This setting determines the time RAS takes to read from and write to a memory cell. Setting options: [Auto], [5T], [6T], [7T], [8T], [9T], [10T], [11T], [12T], [13T], [14T], [15 T].

RAS# to CAS# delay (Trcd)

W hen the Timing Mode is set to [Manual], the field is adjustable. W hen DRAM is refreshed, both rows and columns are addressed separately. This setup item allows you to determine the timing of the transition from RAS (row address strobe) to CAS (column address strobe). The less the clock cycles, the faster the DRAM performance. Setting options: [Auto], [2T], [3T], [4T], [5T], [6T], [7T].

Row Precharge Time (Trp)

W hen the Timing Mode is set to [Manual], the field is adjustable. This item controls the number of cycles for Row Address Strobe (RAS) to be allowed to precharge. If insufficient time is allowed for the RAS to accumulate its charge before DRAM refresh, refreshing may be incomplete and DRAM may fail to retain data. This item applies only when synchronous DRAM is installed in the system. Available settings: [Auto], [2T], [3T], [4T], [5T], [6T], [7T].

Row cycle time (Trc)

W hen the Timing Mode is set to [Manual], the field is adjustable. The row cycle time determines the minimum number of clock cycles a memory row takes to complete a full cycle, from row activation up to the precharging of the active row. Available settings: [Auto], [7T]~[22T].

Row refresh cyc time (Trfc)

W hen the Timing Mode is set to [Manual], the field is adjustable. Auto-refresh

-active to RAS#-active or RAS# auto-refresh. Available settings: [Auto], [9T],

[10T] ~ [24T].

3-11

M S-7125 ATX M ainboard

3-12

Row to Row delay (Trrd)

W hen the Timing Mode is set to [Manual], the field is adjustable. Specifies the active-to-active delay of different banks. Available settings: [Auto], [2T], [3T],

[4T].

Write recover y time (Twr)

W hen the Timing Mode is set to [Manual], the field is adjustable. It specifies the amount of delay (in clock cycles) that must elapse after the completion of a valid write operation, before an active bank can be precharged. This delay is required to guarantee that data in the write buffers can be written to the memory cells before precharge occurs. Available settings: [Auto], [2T], [3T].

Write to Read delay (Twtr)

W hen the Timing Mode is set to [Manual], the field is adjustable. This item controls the W rite Data In to Read Command Delay memory timing. This constitutes the minimum number of clock cycles that must occur between the last valid write operation and the next read command to the same internal bank of the DDR device. Available settings: [Auto], [1T], [2T].

Read to Write delay (Trwt)

W hen the Timing Mode is set to [Manual], the field is adjustable. This is not a

DRAM-specified timing parameter, but must be considered due to routing latencies on the clock forwarded bus. It is counted from the first address bus slot that was not associated with part of the read burst. Available settings: [Auto],

[1T], [2T], [3T], [4T], [5T], [6T].

Refresh period (Tref)

W hen the Timing Mode is set to [Manual], the field is adjustable. Specifies the refresh rate of the DIMM requiring the most frequent refresh. Available settings:

[Auto], [1x1552], [1x2064], [1x2592], [1x3120], [1x3632], [1x4128], [1x4672],

[2x1552], [2x2064], [2x2592], [2x3120], [2x3632], [2x4128], [2x4672], [4x1552],

[4x2064], [4x2592], [4x3120], [4x3632], [4x4128], [4x4672], [128].

User Config mode

This field has the capacity to automatically detect all of the following 4 fields default value.. If you set this field to [Manual], the following fields will be selectable.

The settings are: [Auto], [Manual].

Bottom of 32-bit [ 31:24] IO

When the User Config mode is set to [Manual], the field is adjustable.

This field specifies the memory which could be remapped to another address higher than

00E0. (This item only activities in 64-bit OS) The settings are: [0000~00E0].

1T/ 2T M emory Timing

When the User Config mode is set to [Manual], the field is adjustable. This field controls the SDRAM command rate. Selecting [1T] makes SDRAM signal controller to run at 1T (T=clock cycles) rate. Selecting [2T] makes SDRAM signal controller run at 2T rate. Setting options: [1T], [2T].

BIOS Setup

Read Preamble value

W hen the User Config mode is set to [Manual], the field is adjustable. The time prior to the max-read DQS-return when the DQS receiver should be turned on.

This is specified in units of 0.5ns. The controller needs to know when to enbale its DQS receiver in anticipation of the DRAM DQS driver truning on for a read.

The controller will disable its DQS receiver until the read preamble time and then enable its DQS receiver while the DRAM asserts DQS. Setting options: [2ns], [2.

5ns], [3ns], [3.5ns], [4ns], [4.5ns], [5ns], [5.5ns], [6ns], [6.5ns], [7ns], [7.5ns],

[8ns], [8.5ns], [9ns], [9.5ns].

Async Latency value

When the User Config mode is set to [Manual], the field is adjustable. This field should be loaded with 4-bit value equal to th e maximum asynchronous latency in the DRAM read round-trip loop. Setting options: [2ns], [3ns], [4ns], [5ns],

[6ns], [7ns], [8ns], [9ns], [10ns], [11ns].

S/W memory hole Remapping

This field enables software to remap the physical memory to the address higher than 00E0. (This item only activities in 64-bit OS) Setting options: [Disabled],

[Enabled].

H/W memory hole Remapping

This field enables hardware to remap the physical memory to the address higher than 00E0. (This item only activities in 64-bit OS) Setting options: [Disabled],

[Enabled].

MTRR M apping Mode

This field allows you to control the MTRR mapping Mode. Setting options:

[Discrete], [Continuous].

3-13

M S-7125 ATX M ainboard

Integrated Peripherals

3-14

USB Controller

This setting allows you to enable/disable the onboard USB controller. Selecting

[V1.1+V2.0] enables the system to support both USB 1.1 and 2.0 spec. Setting options: [Disabled], [V1.1], [V1.1+V2.0].

USB KB/Storage Support

Select [Enabled] if you need to use a USB-interfaced keyboard or storage device in the operating system. Setting options: [Enabled], [Disabled].

Onboard LAN Control

This setting controls the onboard LAN controller. Setting options: [Enabled],

[Disabled].

OnBoard LAN Option ROM

This setting is used to enable/disable the onboard LAN Option ROM. Setting options: [Enabled], [Disabled].

OnBoard IEEE1394 Controller

This setting is used to enable/disable the onboard IEEE 1394 controller. Setting options: [Disabled], [Enabled].

OnBoard Sil3114 RAID

This setting controls the onboard Sil3114 RAID chip. Setting options: [Enabled],

[Disabled].

BIOS Setup

Onboard GigaBit LAN

Setting to [Enabled] allows the BIOS to detect the Marvell LAN controller and enable it. Setting options: [Enabled] and [Disabled].

Onboard GigaBit LAN ROM

This setting controls the onboard Marvell LAN Boot ROM. Setting options:

[Enabled], [Disabled].

AC97 Controller

[Auto] allows the mainboard to detect whether an audio device is used. If an audio device is detected, the onboard AC ’ 97 (Audio Codec ’ 97) controller will be enabled; if not, it is disabled. Disable the controller if you want to use other controller cards to connect an audio device. The settings are: [Auto],

[Disabled].

I/O Device Configuration

Press <Enter> to enter the sub-menu and the following screen appears:

Onboard FDC Controller

Select [Enabled] if your system has a floppy disk controller (FDD) installed on the system board and you wish to use it. If you install add-on FDC or the system has no floppy drive, select [Disabled] in this field. The settings are: [Enabled],

[Disabled].

COM Port 1

Select an address and corresponding interrupt for the first serial port. The settings are: [3F8/IRQ4], [2E8/IRQ3], [3E8/IRQ4], [2F8/IRQ3], [Disabled], [Auto].

IR Function Select

This setting allows you to specify the operation mode for serial port 2. Setting options: [IrDA], [ASKIR], [Disable].

[Disable] RS-232C Serial Port

[IrDA] IrDA-compliant Serial Infrared Port

[ASKIR] Amplitude Shift Keyed Infrared Port

3-15

M S-7125 ATX M ainboard

RxD, TxD Active

This setting controls the receiving and transmitting speed of the IR peripheral in use. Setting options: [Hi,Hi], [Hi,Lo], [Lo,Hi], [Lo,Lo].

IR Transmission Delay

This setting determines whether the IR transmission rate will be delayed while converting to receiving mode. Setting options: [Disabled], [Enabled].

UR2 Duplex Mode

This setting controls the operating mode of IR transmission/reception. Setting options: [Full], [Half]. Under [Full] Duplex mode, synchronous, bi-directional transmission/reception is allowed. Under [Half] Duplex mode, only asynchronous, bidirectional transmission/reception is allowed.

Use IR Pins

Please consult your IR peripheral documentation to select the correct setting of the TxD and RxD signals. Setting options: [RxD2/TxD2], [IR-Rx2Tx2].

Parallel Port

There is a built-in parallel port on the on-board Super I/O chipset that provides

Standard, ECP, and EPP features. It has the following options:

[Disabled]

[3BC/IRQ7]

[278/IRQ5]

[378/IRQ7]

Line Printer port 0

Line Printer port 2

Line Printer port 1

Parallel Port M ode

SPP : Standard Parallel Port

EPP : Enhanced Parallel Port

ECP : Extended Capability Port

ECP + EPP: Extended Capability Port + Enhanced Parallel Port

Normal

SPP/EPP/ECP/ECP+EPP

To operate the onboard parallel port as Standard Parallel Port only, choose

[SPP]. To operate the onboard parallel port in the EPP mode simultaneously, choose [EPP]. By choosing [ECP], the onboard parallel port will operate in

ECP mode only. Choosing [ECP + EPP] will allow the onboard parallel port to support both the ECP and EPP modes simultaneously. Choose [Normal] to use Standard Parallel Port + Bi-Directional Mode simultaneously.

3-16

BIOS Setup

EPP M ode Select

The onboard parallel port is EPP Spec. compliant, so after the user chooses the onboard parallel port with the EPP function, the following message will be displayed on the screen: “ EPP Mode Select.

” At this time either [EPP 1.7] spec or [EPP 1.9] spec can be chosen.

ECP Mode Use DMA

The ECP mode has to use the DMA channel, so choose the onboard parallel port with the ECP feature. After selecting it, the following message will appear: “ ECP Mode Use DMA.

” At this time, the user can choose between

DMA channel [3] or [1].

IDE Function Setup

Press <Enter> to enter the sub-menu and the following screen appears:

OnChip IDE Channel 0

The integrated peripheral controller contains an IDE interface with support for two IDE channels. Choose [Enabled] to activate each channel separately.

Settings: [Enabled], [Disabled].

both support Ultra DMA/33, Ultra DMA/66 and Ultra DMA/100 select Auto to enable BIOS support. The settings are: [Auto], [Disabled].

OnChip IDE Channel 1

The integrated peripheral controller contains an IDE interface with support for two IDE channels. Choose [Enabled] to activate each channel separately.

Settings: [Enabled], [Disabled].

IDE DMA Transfer Access

This item is used to enable or disable the DMA transfer function of the IDE

Hard Drive. The settings are: [Enabled], [Disabled].

SATA1/SATA2 & SATA3/SATA4

This item is used to enable or disable onchip SATA controller. The settings are: [Enabled], [Disabled].

3-17

M S-7125 ATX M ainboard

IR Function Select

This setting allows you to specify the operation mode for serial port 2. Setting options: [IrDA], [ASKIR], [Disable].

[Disable] RS-232C Serial Port

[IrDA]

[ASKIR]

IrDA-compliant Serial Infrared Port

Amplitude Shift Keyed Infrared Port

SATA Devices Configuration

Press <Enter> to enter the sub-menu and the following screen appears:

RAID Enabled

This item is used to enable/disable the onchip RAID function. W hen you set to enable and the following fields will be selectabled. Setting options:

[Enabled], [Disabled].

IDE Primary/Secondary Master/Slave RAID

This feature allows users to enable or disable the RAID function for each IDE hard disk drive. Settings: [Enabled], [Disabled].

SATA 1/2/3/4 RAID

This feature allows users to enable or disable the RAID function for each SATA hard disk drive. The settings are: [Enabled], [Disabled].

3-18

Power Management Setup

BIOS Setup

MSI Reminds You...

S3-related functions described in this section are available only when your BIOS supports S3 sleep mode.

ACPI Standby State

This item specifies the power saving modes for ACPI function. If your operating system supports ACPI, such as W indows 98SE, W indows ME, W indows 2000, and

W indows XP, you can choose to enter the Standby mode in S1(POS) or S3(STR) fashion through the setting of this field. Options are:

[S1 (POS)] The S1 sleep mode is a low power state. In this state, no system context is lost (CPU or chipset) and hardware main-

[S3 (STR)] tains all system context.

The S3 sleep mode is a lower power s tate where the in formation of system configuration and open applications/files is saved to main memory that remains powered while most other hardware components turn off to save energy. The information stored in memory will be used to restore the system when a “ wake up ” event occurs.

Video Off M ethod

This determines the manner in which the monitor is blanked.

[V/H SYNC+Blank] This selection will cause the system to turn off the vertical and horizontal synchronization ports and write

[Blank Screen]

[DPMS Support] blanks to the video buffer.

This option only writes blanks to the video buffer.

Initial display power management signalling.

3-19

M S-7125 ATX M ainboard

Power Button Function

This feature sets the function of the power button. Settings are:

[Power Off] The power button functions as normal power off button.

[Suspend] W hen you press the power button, the computer enters the suspend/sleep mode, but if the button is pressed for more than four seconds, the computer is turned off.

Restore On AC Power Loss

This item specifies whether your system will reboot after a power failure or interrupt occurs. Available settings are:

[Off] Always leaves the computer in the power off state.

[On]

[Last State]

Always leaves the computer in the power on state.

Restores the system to the status before power failure or interrupt occurred.

Wake-Up Event Activity

Press <Enter> and the following sub-menu appears.

Resume S3 by PS2/Keyboard, Resume S3 by PS2/M ouse

These fields allow the activity of the PS2 (keyboard and mouse) to wake up the system from S3 sleep state. Settings: [Enabled], [Disabled].

Resume By PCI Device PM E#

W hen set to [Enabled], the feature allows your system to be awakened from the power saving modes through any event on PME (Power Management Event).

Settings: [Enabled], [Disabled].

Resume By RTC Alarm

The field is used to enable or disable the feature of booting up the system on a scheduled time/date. Settings: [Enabled], [Disabled].

Date

The field specifies the date for Resume By RTC Alarm .

Settings: [0]~[31].

HH:MM:SS

The field specifies the time for Resume By RTC Alarm . Format is <hour>

<minute><second>.

3-20

BIOS Setup

PNP/PCI Configurations

This section describes configuring the PCI bus system and PnP (Plug & Play) feature. PCI, or P eripheral C omponent I nterconnect, is a system which allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings.

Primary Graphic

’ s Adapter

This item specifies which graphic card is your primary graphics adapter. Settings:

[First PCIE], [PCI Slot] .

Resource Controlled By

The Award Plug and Play BIOS has the capacity to automatically configure all of the boot and Plug and Play compatible devices. However, this capability means absolutely nothing unless you are using a Plug and Play operating system such as W indows

®

95/98. If you set this field to [Manual], choose specific resources by going into each of the sub menu that follows this field (a sub menu is preceded by a “ } ” ). The settings are: [Auto (ESCD)], [Manual].

IRQ Resources

The items are adjustable only when Resources Controlled By is set to [Manual].

Press <Enter> and you will enter the sub-menu of the items. IRQ Resources list IRQ

3/4/5/7/9/10/11/12/14/15 for users to set each IRQ a type depending on the type of device using the IRQ. Settings are:

[PCI Device]

[Reserved]

For Plug & Play compatible devices designed for PCI bus architecture.

The IRQ will be reserved for further request.

3-21

M S-7125 ATX M ainboard

** PCI Express relative items **

M aximum Payload Size

This item allows you to set the PCI Express Maximum payload size per time . Settings:

[4096], [128], [256], [512], [1024], [2048] .

MSI Reminds You...

IRQ (Interrupt Request) lines are system resources allocated to I/O devices. When an I/O device needs to gain attention of the operating system, it signals this by causing an IRQ to occur. After receiving the signal, when the operating system is ready, the system will interrupt itself and perform the service required by the I/O device.

3-22

BIOS Setup

H/W Monitor

This section shows the status of your CPU, fan, overall system status, etc.

Monitor function is available only if there is hardware monitoring mechanism onboard.

Chassis Intrusion Detect

The field enables or disables the feature of recording the chassis intrusion status and issuing a warning message if the chassis is once opened. To clear the warning message, set the field to [Reset]. The setting of the field will automatically return to

[Enabled] later. Setting options: [Enabled], [Reset], [Disabled].

Smart CPU Fan Target

There are 2 pairs of Temperature/FAN Speed control: System Temperature with

System Fan, and CPU Temperature with CPU Fan. W 83627THF provides the Smart

Fan system which can control the fan speed automatically depending on the current temperature to keep it with in a specific range. Settings: [40 o C/104 o F], [40 o C/104 o F],

[40 o C/104 o F], [Disabled].

PC Health Status

Press <Enter> and the following sub-menu appears.

Current System/CPU Temperature, System Fan/CPU Fan Speed, Vcore,

+12.0V, +3.3V, +5.0V, Battery, +5VSB

These items display the current status of all of the monitored hardware devices/components such as CPU voltage, temperatures and all fans ’ speeds.

3-23

M S-7125 ATX M ainboard

Cell Menu

The items in Cell Menu includes some important settings of CPU, AGP, DRAM and overclocking functions.

MSI Reminds You...

Change these settings only if you are familiar with the chipset.

Current CPU / DDR Clock

These two items show the current clocks of CPU & DDR. Read-only.

High Performance M ode

This field allows you to select the DDR timing setting. Setting options: [Manual],

[Optimized].

Aggressive timing

This item allows you to enable or disable the memory clock. When [Enabled] is selected, the timing delay of memory will be shorten to increase the performance. Setting options: [Enabled], [Disabled].

3-24

BIOS Setup

Dynamic Overclocking

Dynamic Overclocking Technology is the automatic overclocking function, included in the MSI TM ’ s newly developed CoreCell TM Technology. It is designed to detect the load balance of CPU while running programs, and to adjust the best CPU frequency automatically. W hen the motherboard detects CPU is running programs, it will speed up CPU automatically to make the program run smoothly and faster. W hen the CPU is temporarily suspending or staying in the low load balance, it will restore the default settings instead. Usually the Dynamic Overclocking Technology will be powered only when users' PC need to run huge amount of data like 3D games or the video process, and the CPU frequency need to be boosted up to enhance the overall performance.

Setting options:

[Disabled]

[Private]

[Sergeant]

[Captain]

Disable Dynamic Overclocking function.

1st level of overclocking, increasing the CPU frequency by 1%.

2nd level of overclocking, increasing the CPU frequency by 3%.

3rd level of overclocking, also the default value of "Load High

Performance Defaults", increasing the CPU frequency by 5%.

[Colonel]

[General]

4th level of overclocking, increasing the CPU frequency by 7%.

5th level of overclocking, increasing the CPU frequency by 9%.

[Commander] 6th level of overclocking, increasing the CPU frequency by 11%.

MSI Reminds You...

Even though the Dynamic Overclocking Technology is more stable than manual overclocking, basically, it is still risky. We suggest user to make sure that your CPU can afford to overclocking regularly first.

If you find the PC appears to be unstable or reboot incidentally, it's better to disable the Dynamic Overclocking or to lower the level of overclocking options. By the way, if you need to conduct overclocking manually, you also need to disable the D.O.T Ranger first.

Adjust CPU FSB Frequency

This item allows you to select the CPU Front Side Bus clock frequency (in MHz).

Select the number between [200]~[400] for needed frequency.

HT Frequency

This setting specifies the maximum operating frequency of the link ’ s transmitter clock.

Setting options: [1x], [1.5x], [2x], [2.5x], [3x], [4x], [5x].

HT Width

This field allows you to set the HT W idth between CPU & Chip.

mark means Chip to

CPU HT Width. And

mark means CPU to Chip HT W idth. Setting options: [

8

8],

[

16

8], [

8

16], [

16

16].

CPU Spread Spectrum

This setting is used to enable or disable the CPU Spread Spectrum feature. W hen overclocking the CPU, always set it to [Disabled]. Setting options: [Center Spread],

[Disabled].

3-25

M S-7125 ATX M ainboard

SATA Spread Spectrum

This setting is used to enable or disable the SATA Spread Spectrum feature. Setting options: [Disabled], [Down Spread].

PCIE Spread Spectrum

This setting is used to enable or disable the CPU Spread Spectrum feature. W hen overclocking the CPU, always set it to [Disabled]. Setting options: [Disabled], [Down

Spread].

PCIE Clock

The system board designer selects whether the PCIE clock is tightly synchronized with the CPU clock or is asynchronous. Setting options: [100MHz]~[145MHz].

SSE/ SSE2 Instructions

This setting disables/enables the SSE/SSE2 Instructions. The Streaming SIMD Extensions (SSE) were introduced in the Pentium III processor. The SSE extensions consist of a new set of instructions and a new set of registers. These instructions and registers are designed to allow Single-Instruction Multiple-Data (SIMD) computations to be made on single-precision floating-point numbers.

The Streaming SIMD Extensions 2 (SSE2) were introduced in the Pentium 4 and Intel

Xeon processors. They consist of a new set of instructions that operate on the XXM and MXCSR registers and perform SIMD operations on double-precision floatingpoint values and on integer values.Several of these new SSE/SSE2 instructions also operate in the MMX registers. Setting options: [Enabled], [Disabled].

Cool

’ n

Quiet control

This feature is especially designed for AMD Athlon processor, which provides a CPU temperature detecting function to prevent your CPU ’ s from overheating due to the heavy working loading. Setting options: [Disabled], [Enabled].

3-26

BIOS Setup

Adjust CPU Ratio

This item lets you adjust the CPU ratio. Setting to [Startup] enables the CPU running at the fastest speed which is detected by system. Setting options are: [Startup], [x4]~

[x12].

Adjust CPU VID

This item lets you adjust the CPU VID. Setting to [Startup] enables the CPU running at the default VID which is detected by system. Setting options are: [Startup], [0.825V],

[0.850V],[0.875V],~, [1.550V].

CPU Voltage

This feature allows you to trim the voltage of CPU. Setting options are: [By CPU VID],

[Over VID 3.3%], [Over VID 5.0%],[Over VID 8.3%].

M emory Voltage

Adjusting the DDR voltage can increase the DDR speed. Any changes made to this setting may cause a stability issue, so changing the DDR voltage for long-term purpose is NOT recommended . Setting options are: [Auto], [2.50V]~[2.85V].

NF4 Voltage

NV4 voltage is adjustable in the field. Setting options are: [1.50V]~[1.85V].

MSI Reminds You...

The settings shown in different color in CPU Voltage , Memory Voltage and NF4 Voltage help to verify if your setting is proper for your system.

G ray: Default setting.

Yellow: High performance setting.

Red: Not r ecommended setting and the system may be unstable.

Changing CPU VID, CPU Voltage, M emory Voltage and NF4 Voltage may result in the instability of the system; therefore, it is NOT recommended to change the default setting for long-term usage.

3-27

M S-7125 ATX M ainboard

Optimized Defaults

The two options on the main menu allow users to restore all of the BIOS settings to the default Optimized values. The Optimized Defaults are the default values set by the mainboard manufacturer specifically for optimal performance of the mainboard. The Fail-Safe Defaults are the default values set by the BIOS vendor for stable system performance.

W hen you select Load Optimized Defaults, a message as below appears:

Pressing Y loads the default factory settings for optimal system performance.

3-28

BIOS Setup

BIOS Setting Password

W hen you select this function, a message as below will appear on the screen:

Type the password, up to eight characters in length, and press <Enter>. The password typed now will replace any previously set password from CMOS memory.

You will be prompted to confirm the password. Retype the password and press

<Enter>. You may also press <Esc> to abort the selection and not enter a password.

To clear a set password, just press <Enter> when you are prompted to enter the password. A message will show up confirming the password will be disabled. Once the password is disabled, the system will boot and you can enter Setup without entering any password.

W hen a password has been set, you will be prompted to enter it every time you try to enter Setup. This prevents an unauthorized person from changing any part of your system configuration.

3-29

Introduction to DigiCell

Introduction to DigiCell

DigiCell, the most useful and powerful utility that MSI has spent much research and efforts to develop, helps users to monitor and configure all the integrated peripherals of the system, such as audio program, power management, MP3 files management and communication / 802.11g W LAN settings. Moreover, with this unique utility, you will be able to activate the

MSI well-known features, Live Update and Core Center, which makes it easier to update the BIOS/drivers online, and to monitor the system hardware status (CPU/Fan temperature and speed) or to overclock the CPU/ memory.

Once you have your DigiCell installed (locate the setup source file in the setup CD accompanying with your mainboard, path: Utility --> MSI Utility --> MSI DigiCell ), it will have an icon in the system tray, a short cut icon on the desktop, and a short cut path in your “ Start-up ” menu. You may double-click on each icon to enable DigiCell.

short-cut icon in the system tray short-cut path in the start-up menu

(path: Start-->Programs-->MSI-->DigiCell)

4-1

Main

Before using this utility, it is required to have all the integrated peripherals/cards (LAN card, W ireless LAN card, MegaStick... etc.) and all the necessary drivers (onboard

LAN driver, audio driver, CoreCenter, Live Update... etc.) installed correctly.

The icon representing each item will be lit up if it is inserted/installed correctly and properly. Otherwise, the icon will remain gray and user is not able to view the functionality/connection of that item.

4-2

Introduction:

Click on each icon appearing above to enter the sub-menu to make further configuration.

M SI

Click on this button to link to MSI website: http://www.msi.com.tw.

Quick Guide

Click on this button and the quick guide of DigiCell will be displayed for you to review.

H/W Diagnostic

In this sub-menu, it provides the information of each DigiCell button for you to check if the representing peripherals/cards/drivers are correctly installed.

Comm.

In this sub-menu, you can see the configuration details for communication products, including the status, strength, speed and channel of the connection of the Ethernet LAN & W ireless LAN.

Software Access Point

In this sub-menu, you can change your connection mode to different ones, and configure the advanced settings for each mode, such as the authentication encryption... etc.

Introduction to DigiCell

Live Update

You can take advantage of Live Update to detect and update BIOS and drivers online.

Core Center

You can take advantage of Core Center to monitor the health status of your system and to overclock under W indows O S if your sys tem s upports overclocking function.

M EGA STICK

If you have your MEGA STICK connected to your system, this icon will be lit up. Click this blue icon to turn DigiCell into a MP3 player, and then you can load media files from your MEGA STICK or the system, and edit the preferred playlist.

Audio Speaker Setting

In this sub-menu, you can configure and test the multi-channel audio function, speakers, sound effect and environment.

Power on Agent

In this sub-menu, you can configure date, time and auto-executed programs of the power-on, power-off and restarting features.

MSI Reminds You...

Click on back button in every sub-menu and it will bring you back to the main menu.

4-3

4-4

H/W Diagnostic

In the H/W Diagnostic sub-menu, you can see the information, status and note of each DigiCell. You may double check the connection and installation of the item marked as gray.

You may also click on the Mail to MSI button to send your questions or suggestions to MSI ’ s technical support staff.

Introduction to DigiCell

Communication

In the Communication sub-menu, you can see the status of all the LAN / W LAN /

Bluetooth on the screen if the hardware is installed. The first icon indicates the onboard LAN on your system, the second icon indicates the wireless LAN status, and the third one is the information about the bluetooth on your system. Click on each item for details.

This icon indicates the information and connection status of onboard LAN, which is read-only.

The second icon indicates the wireless connection. You may click this icon to configure the advanced settings in the WLAN Card Mode dialogue box

(see the image on p.4-8). Please note that it is only available when the

Software Access Point is set to WLAN Card Mode .

The third icon indicates the connection using bluetooth devices. If your system is connected to the bluetooth device, the icon will light up.

4-5

Software Access Point

In the Software Access Point sub-menu, you can see the communication status on your system and choose the desired software access point mode by clicking on the desired icon, in which the default settings are configured for your usage. The default software access point mode is set to WLAN Car d M ode . For more advanced security settings and channels switching, click on “ Setting ” button to enter its submenu.

4-6

Terminology

Here are the introduction of W LAN / AP communication terminology.

WEP Key

In the wireless network environment, the administrator can set up password

(Network Key) to protect the network from being attacked or unauthorized access. W hen building the network, you can set up 4 sets of W EP keys, which can be 5 characters (10 hex-adecimal digital) or 13 characters (26 hex-adecimal digital) and specify one of them to use.

Ad-hoc M ode

An Ad-hoc network is a local area network or other small network, especially one with wireless or temporary plug-in connections, in which some of the network devices are part of the network only for the duration of a communications session. Users in the network can share files, print to a shared printer, and access the Internet with a shared modem. In this kind of network, new devices can be quickly added; however, users can only communicate with other wireless LAN computers that are in this wireless LAN workgroup, and are within range.

Infrastructure M ode

The difference between Infrastructure network and Ad-hoc network is that the former one includes an Access Point. In an Infrastructure network, the

Access Point can manage the bandwidth to maximize bandwidth utilization.

Additionally, the Access Point enables users on a wireless LAN to access an existing wired network, allowing wireless users to take advantage of the wired networks resources, such as Internet, email, file transfer, and printer sharing. The scale and range of the Infrastructure networking are larger and wider than that of the Ad-hoc networking.

Introduction to DigiCell

Access Point Mode

Click on “ Setting ” button of the Access Point Mode and the following screen will display.

IP Sharing

Click on this icon to enable/disable the IP sharing. The default of this setting is disabled.

Disabled.

Enabled.

Enabling/disabling IP sharing depends on the different situation. For example:

1. If your family and you are getting on Internet at home with multi computers, and your ISP only provides one IP for you, you may need to enable IP Sharing function in order to use this one IP to get on Internet with multi computers simultaneously.

2. If you are getting on Internet in office, usually the LAN card will automatically get the IP this computer uses. In this case you don ’ t have to enable this function.

SSID

Means Service Set Identifier, a unique name shared among all points in a wireless network. It must be identical for all points in the network. Then the card will be able to connect to an access point with the same SSID.

Channel

Specifies the operating radio frequency channel in Infrastructure mode , which should be set to an available one (ex: with less traffic to ensure the stable and better connection).

Associated Client List

This option is to display information of stations that are currently associated to your wireless gateway.

Association Control

This option allows you to control which PC can connect to the wireless LAN. If you

4-7

4-8 enable this feature, only PCs with MAC address located in Association Control List can connect to the wireless LAN.

M AC Addr ess

MAC stands for Media Access Control. A MAC address is the hardware address of a device connected to a network.

Security

This option allows you to enable/disable the authentication function.

Authentication

Open : Communicates the key across the network.

Shared : Devices must have identical W EP settings to communicate.

WLAN Card Mode

Click on “ Setting ” button of the WLAN Card Mode for the WEP status of your APs.

If the AP you are selecting (the highlighted one) is not encrypted ( Disabled shown in the Encryption column), the screen will display as below. You can click “ Connect ” to make connection to that AP, click “ Cancel ” to close this dialogue box, or click

“ Refresh ” button to update the available W LAN connections.

If the network you are selecting is encrypted ( WEP shown in the Encryption column), the screen will display as below. You need to enter the correct W EP key defined by

AP in the specified WEP Key 1~4 fields to make the connection.

Introduction to DigiCell

Live Update

Click on the Live Update icon in the main menu and the Live Update program will be enabled.

The Live Update 3 ™ is a tool used to detect and update your BIOS/ drivers/VGA BIOS/VGA Driver/OSD/Utility online so that you don

’ t need to search for the correct BIOS/driver version throughout the whole Web site. To use the function, you need to install the “ MSI Live

Update 3 ” application. After the installation, the “ MSI Live Update 3 ” icon (as shown on the right) will appear on the screen.

Double click the

MSI Live Update 3

icon, and the following screen will appear:

Six buttons are placed on the left column of the screen. Click the desired button to start the update process.

Live BIOS – Updates the BIOS online.

Live Driver – Updates the drivers online.

Live VGA BIOS – Updates the VGA BIOS online.

Live VGA Driver

Updates the VGA driver online.

Live OSD – Updates the firmware of the OSD products online.

Live Utility – Updates the utilities online.

If the product you purchased does not support any of the functions listed above, a

“ sorry

message is displayed. For more information on the update instructions, insert the companion CD and refer to the “ Live Update Guide ” under the “ Manual ” Tab.

4-9

MEGA STICK

In the MEGA STICK sub-menu, you can configure the settings of MSI MEGA STICK and the media files (*.m3u, *.mp3, *.wav, *.cda, *.wma) on your system.

Basic Function

Here you can edit your own play list with the buttons

“ load

,

“ save

,

“ delete

,

“ shuttle ” , “ repeat ” & “ print ” .

Load To load media files or the playlist of mp3 files (*.m3u) on your system or on your MEGA STICK.

Save To save a loaded playlist of mp3 files (*.m3u) on your system or on your MEGA STICK.

Del ete Click on the media files in the Play List: field and use “ Delete ” button to remove the media file from the play list. You may remove multi media files simultaneously by using “ Ctrl ” to select multi files.

Shuffle To play the media file in the Play List: in a random order.

R epeat To repeat the selected files in the Play List: .

Print This button has 2 functions:

1. To print out the details of current play list through your printer with the following information:

Song title --- Song length --- Singer name

2. To save the details of current play list and save the file in the plain text file format in the \\Program files\MSI\DigiCell\MyMusic.txt

for your reference. The MyMusic.txt

file is with the following information:

Song title --- Song length --- Singer name

4-10

Introduction to DigiCell

There is also a toolbar for you to execute some basic function, like play, stop, pause, previous/next song, song info and volume adjust. There is also a scroll bar on the top for you to forward/rewind .

previous pause next forward/rewind bar stop song ’ s information play

Right-click on the MP3 file and choose

Info

, a MP3 Info dialogue will pop up to show the information of the file, including the title, artist, album, release year and others. You may also add your own comment in the comment field. Then click “ Save ” to save the change, click

“ Cancel ” to discard the change, or click “ Remove ” to remove all this information.

4-11

Non-Unicode programs supported

If you are using an operating system in European languages, and you

’ d like to play the media files in MEGA STICK with East-Asian languages (such as Chinese, Japanese...

etc.), it is possible that the file names display incorrectly.

However, you can ins tall the Supplemental Language Suppor t provided by

Microsoft to solve this problem. You need to have your Microsoft Setup CD prepared in the CD-ROM. The system will start to install the necessary components after the settings are configured here. Follow the steps described below.

1. Go to [Control Panel] and choose [Regional and Languages Options].

2. Go to the [Languages] tab and enable the check box of [Install files for East

Asian languages]. A dialogue box will pop up to remind you the above selection is chosen.

4-12

Introduction to DigiCell

3. Then go to the [Advanced] tab and select the language you want to be supported (the language of the filename in the MegaStick) from the dropdown list in the [Language for non-Unicode programs], then click [Apply]. The system will install the necessary components from your Microsoft Setup CD immediately.

4-13

Core Center (for AMD K8 Processor)

Click on the Core Center icon in the main menu and the Core Center program will be enabled.

Cool

n

Quiet

This utility provides a CPU temperature detection function called Cool ’ n ’ Quiet .

Cool ’ n ’ Quiet is a special feature designed only for AMD

®

Athlon64 processor, and with Cool ’ n ’ Quiet , the system will be capable of detecting the temperature of the

CPU according to the CPU

’ s working loading. When the CPU temperature climbs up to a certain degree, the speed of the system cooling fan will be risen automatically. On the other hand, the speed of the system cooling fan will slow down instantly when the CPU temperature descends to its normal degree.

Here the current system status (including Vcore, 3.3V, +5V and 12V) and the current

PC hardware status (such as the CPU & system temperatures and all fans speeds) are shown on the left and right sides for you to monitor.

W hen you click the red triangles in the left and right sides, two sub-menus will open for users to overclock, overspec or to adjust the thresholds of system to send out the warning messages.

4-14

Introduction to DigiCell

Left-side: Current system status

In the left sub-menu, you can configure the settings of FSB, PCI-E, Memory Voltage and CPU Voltage by clicking the radio button in front of each item and make it available

(the radio button will be lighted as yellow when selected), use the “ + ” and “ ” buttons to adjust, then click “ OK ” to apply the changes. Then you can click “ Save ” to save the desired FSB you just configured. Or you may click “ Default ” to restore the default values.

Right-side: PC hardware status during real time operation

In the right sub-menu, here you can configure the PC hardware status such as CPU

& system temperatures and fan speeds. You may use the scroll bars to adjust each item, then click “ OK ” to apply the changes. The values you set for the temperatures are the maximum thresholds for the system warnings, and the values for fan speeds are the minimum thresholds.

Center-side: Cool

n

Quiet / User mode

Here you may adjust the CPU fan speed. If you choose User mode , you may adjust the CPU fan speed in 8 different modes, from High Speed to Low speed . If you choose Cool

’ n

Quiet , the system will automatically configure an optimal setting for you.

MSI Reminds You...

To ensure that C ool ’ n ’ Quiet function is activated and will be working properly, it is required to double confirm that:

1. Run BIOS Setup, and select Cell Menu . Under Cell

M enu , find Cool

’ n

Quiet

Support , and set this item to “ Enable.

2. Enter Windows, and select

[ S t a r t ] - > [ S e t t i n g s ] - >

[Control Pannel]->[Power

O pt io ns ] . E n t er P ow e r

Options Pr operties tag, a n d s e l e c t M i n i m a l

Power M anagement under Power schemes .

4-15

Audio Speaker Setting

In the Audio Speaker Setting sub-menu, you can configure the multi-channel audio operation, perform speaker test, and choose the environment you prefer while enjoying the music.

You can scroll the bar of each equalizer to regulate the current playing digital sound source. Also you may click on the

“ on

button to enable/disable the equalizer function.

Once the equalizer function is enabled, you can choose several preset equalizers for your preference. You may also right-click anywhere to execute this function.

After you have chosen one equalizer, it will be indicated next to the “ on ” button in yellow.

The Environment setting lets you select the environment you like, such as

Cave or Convert Hall .

4-16

Introduction to DigiCell

Click on the “ Speaker test ” button and the following dialogue box will appear:

In this Speaker Configuration dialogue box, select the audio configuration which is identical to the audio jack on your mainboard. Once the correct audio configuration is selected, click “ Apply ” to save the changes. Then the following screen will appear. In this Speaker Configuration dialogue box, first select the correct item from the Speaker mode drop-down list, and then click on each connected speaker to ensure if Headphone, 2-, 4-, 5.1-, or 7.1- channel audio operation is working properly. If any speaker fails to make sound, then check whether the cable is inserted firmly to the connector, or replace the bad speakers with good ones.

Center

Front Left

Main Side Left

Rear Left

Subwoofer

Front Right

Main Side Right

Rear Right

4-17

Power on Agent

In the Power on Agent sub-menu, you can configure setting of power-on, poweroff and restarting status.

In the screen below, you can set the date, time, start-up programs respectively for power-on, power-off and restarting.

Power On

Here are the available settings for Power On function:

Date

T im e

Use the drop-down list to select the date for power-on.

Use the arrow keys to select the hour/minute/second for power-on, power-off and restarting. Then click “ Apply ” to save the changes. As you click “ Apply ” , the following dialogue will appear to show you the next power-on schedule, and the system will start to count down to restart. Click “ OK ” to restart the computer right away or click “ Later ” to restart your computer later.

MSI Reminds You...

Please note that the new setting will not take effect until you restart your computer.

4-18

Introduction to DigiCell

Power Off / Restart

You may configure the time (in the format hh:mm:ss) for the next power-off / restart.

Start With

Use the button “ +Add ” to add the start-up programs as DigiCell is activated next time. For example, you may like to have Outlook activated or a specified website linked when you get to the office every morning.

Step 1: Click on the Program: field and click “ >> ” button to browse for the path of Outlook or

Internet Explorer.

Step 2: Click on “ OK ” to apply the setting.

add the desired startwith program

Step 3: For specified file or specified website, you may enter the file name with the complete path or the website link in the Parameters: field.

To activate Outlook as DigiCell is enabled next time

To activate a specified website as DigiCell is enabled next time

Of course you may use the button “ -Delete ” to remove the added programs, or you can right-click on the selected program and click Delete .

delete the added program

MSI Reminds You...

You can also enable the Every turn on function, which will enable the specified program(s) and file(s) every time the Digi Cell utility runs.

4-19

Auto Login

Since the Power On function allows the system to power on automatically, you may have to enable this Auto Login function in the following situations:

1. If you are using a computer belonging to a domain in office, and you need to enter your user name & password everytime when you boot up your computer.

2. If there are multi users using the same computer and you ’ d like to power on the computer automatically with one specific user.

Enable Auto Login

Enable this setting if you want to use the Auto Login feature. It supports the following operating systems: W in9X, W indows ME, W indows 2000 & W indows XP.

Default User Name

It is only available for W indows 2000 & W indows XP.

-- If you are using a computer belonging to a domain in office, please enter your login user name in this field.

-- If you are using a computer with multi users (for Windows XP operating system), please enter the user name you

’ d like to auto power-on in this field.

Default Password

It is only available for W indows 2000 & W indows XP.

-- If you are using a computer belonging to a domain in office, please enter your login password in this field.

-- If you are using a computer with multi-users (for Windows XP operating system), please enter the password for the user name you ’ d like to auto power-on in this field.

4-20

nVIDIA RAID Introduction

Chapter 5. nVidia RAID Introduction nVidia RAID Introduction

NVIDIA brings Redundant Array of Independent Disks (RAID) technology

— which is used by the world

’ s leading businesses

— to the common PC desktop. This technology uses multiple drives to either increase total disk space or to offer data protection. For all levels, RAID techniques optimize storage solutions by using multiple disks grouped together and treating them as a s ingle storage resource.

5 - 1

M S-7125 ATX M ainboard

Introduction

System Requirement

Operating System Support

NVRAID supports the following operating systems:

W indows XP Home Edition

W indows XP Professional Edition

W indows 2000 Professional

RAID Arrays

NVRAID supports the following types of RAID arrays described in this section:

RAID 0: RAID 0 defines a disk striping scheme that improves the disk read and write times for many applications.

RAID 1: RAID 1 defines techniques for mirroring data.

RAID 0+1: RAID 0+1 combines the techniques used in RAID 0 and RAID 1 arrays.

Spanning (JBOD): JBOD provides a method for combining drives of different s i z e s into one large disk.

Summary of RAID Configurations

Array

RAID 0

RAID 1

RAID 0+1

JBOD

Uses

Non-critical data requiring high performance.

Small databases or any other small capacity environment requiring fault tolerance.

Critical data requiring high performance.

Advantages

High data throughput.

100% data redundancy.

Combining odd size drives into one big drive

Optimized for both

100% data redundancy and performance.

Allows spare disks.

Combines and uses the capacity of odd size drives.

Drawbacks

No fault tolerance.

Requires 2 drives for the storage space of 1 drive.

Requires 2 drives for the storage space of 1 drive

— the same as

RAID level 1.

Decreases performance because of the difficulty in using drives concurrently or to optimize drives for different uses.

# Hard

Disks multiple

2

4+

Multiple

Fault

Tolerance

None

Yes

Yes

No

MSI Reminds You...

Please note that users cannot install OS, either WinME or Win98, in their SATA hard drive. Under these two OSs, SATA can not support.

5 - 2

nVIDIA RAID Introduction

RAID Configuration

Basic Configuration Instructions

The following are the basic steps for configuring NVRAID:

Non-Bootable RAID Array

1. Choose the hard disks that are to be RAID enabled in the system BIOS.

2. Specify the RAID level, either Mirroring (RAID 1), Striping (RAID 0), Striping and

Mirroring (RAID 0+1), or Spanning (JBOD) and create the desired RAID array.

3. Enter the W indows OS, run the W indows nForce Setup application and install the

RAID software. (Check p.5-9 for details.)

4. Initialize the NVRAID Array Disks.

Bootable RAID Array

1. Choose the hard disks that are to be RAID enabled in the system BIOS.

2. Specify the RAID level, either Mirroring (RAID 1), Striping (RAID 0), Striping and

Mirroring (RAID 0+1), or Spanning (JBOD) and create the desired RAID array.

3. Boot from the W indows CD, use the floppy disk that has the RAID driver to copy

and install the nForce RAID software. (Check p.5-9 for details.)

4. Initialize the NVRAID Array Disks.

Setting Up the NVRAID BIOS

Be sure to enable the IDE RAID or SATA RAID items in RAID Config of Integrated

Peripherals in BIOS before configuring the NVRAID BIOS. After that press F10 to save the configuration and exit. The PC will reboot right away. Then enter the RAID

BIOS Setup by pressing F10 when prompted, and follow the procedures described below to set up the NVRAID BIOS.

NVRAID BIOS setup lets you choose the RAID array type and which hard drives you want to make part of the array.

Entering the RAID BIOS Setup

1. After rebooting your PC, wait until you see the RAID software prompting you to press F10 . The RAID prompt appears as part of the system POST and boot process prior to loading the OS.

2. Press F10 , and the NVIDIA RAID Utility

--- Define a New Array window will appear.

The default RAID Mode is set to Mirroring and Striping Block is set to

O pti mal .

5 - 3

M S-7125 ATX M ainboard

Understanding the “ Define a New Array ” Window

Use the Define a New Array window to

• Select the RAID Mode

Set up the Striping Block

• Specify which disks to use for the RAID Array

Depending on the platform used, the system can have one or more channels. In a typical system there is usually one controller and multiple channels, and each channel has a slave and a master.

The channel/controller/master/slave status of each hard disk is given in the Loc

(location) columns of the Free Disks and Array Disks lists.

In the example above, 1.0.M means the hard drive is attached to Channel 1, Controller

0, and the drive is set to Master. The following is a list of all possible combinations:

Parallel ATA

0.0.M

0.0.S

Channel 0, controller 0, Master

Channel 0, controller 0, Slave

0.1.M

0.1.S

Channel 0, controller 1, Master

Channel 0, controller 1, Slave

Serial ATA

1.0.M

1.1.M

2.0.M

2.1.M

Channel 1, controller 0, Master

Channel 1, controller 1, Master

Channel 2, controller 0, Master

Channel 2, controller 1, Master

MSI Reminds You...

There is no such thing as Slave drive in Serial ATA. All drives are considered to be Master since there is a one to one connection between the drive and the controller.

5 - 4

nVIDIA RAID Introduction

Using the Define a New Array Window

If necessary, press the tab key to move from field to field until the appropriate field is highlighted.

• Selecting the RAID Mode

By default, this is set to [Mirroring]. To change to a different RAID mode, press the down arrow key until the mode that you want appears in the RAID Mode box — either

[Mirroring], [Striping], [Spanning], or [Stripe Mirroring].

• Selecting the Striping Block Size

Striping Block size is given in kilobytes, and affects how data is arranged on the disk. It is recommended to leave this value at the default [Optimal], which is 32KB, but the values can be between [4 KB] and [128 KB].

• Assigning the Disks

The disks that you enabled from the RAID Config BIOS setup page appear in the Free

Disks block. These are the drives that are available for use as RAID array disks.

To designate a free disk to be used as a RAID array disk,

1. Tab to the F ree Disks section. The first disk in the list is selected.

2. Move it from the Free Disks block to the Array Disks block by pressing the right arrow key (-->). The first disk in the list is moved, and the next disk in the list is selected and ready to be moved.

3. Continue pressing the right-arrow key (<-- ) until all the disks that you want to use as RAID array disks appear in the Array Disks block.

It shows that two disks have been assigned as RAID1 array disks in the figure above.

5 - 5

M S-7125 ATX M ainboard

Completing the RAID BIOS Setup

1. After assigning your RAID array disks, press F7. The Clear disk data prompt appears.

2. Press Y if you want to wipe out all the data from the RAID array, otherwise press

N . You must choose Yes if the drives were previously used as RAID drives.

The Array List window appears, where you can review the RAID arrays that you have set up.

3.

Use the arrow keys to select the array that you want to set up, then press Enter.

The Array Detail window appears.

4.

If you want to mark this disk as empty and wipe out all its contents then press C .

5.

At the prompt, press Y to wipe out all the data, otherwise press N .

6. Press Enter again to go back to the previous window and then press Ctrl-X to exit the RAID setup. Now that the RAID setup has been configured from the RAID

BIOS, the next step is to configure and load NVRAID drivers under W indows, as explained in

Installing the NVIDIA RAID Software Under W indows

on p5-9.

5 - 6

nVIDIA RAID Introduction

NVIDIA RAID Utility Installation

Installing the RAID Driver (for bootable RAID Array)

1. After you complete the RAID BIOS setup, boot from the W indows CD, and the

W indows Setup program starts.

2. Press F6 and wait for the W indows Setup screen to appear.

3. Specify the NVIDIA drivers:

(1) Insert the floppy that has the RAID driver, press S, then press Enter. The

W indows Setup screen appears as below:

MSI Reminds You...

Please follow the instruction below to make an nVIDIA RAID driver for yourself.

1. Insert the MSI CD into the CD-ROM drive.

2. Ignore the Setup screen and use

Explorer

to browse the CD.

3. Copy all the c ontents (not inc luding the s ub-folders ) in the

\\nVidia\System\CK804\IDE\WinXP

or \\nVidia\System\CK804\IDE\Win2k to a formatted floppy disk.

4. The driver disk for nVIDIA RAID driver is done.

(2) Select “ NVIDIA RAID CLASS DRIVER ” and then press Enter .

(3) Press S again at the Specify Devices screen, then press Enter.

(4) Select “ NVIDIA NForce Storage Controller ” and then press Enter. The following W indows Setup screen appears listing both drivers:

5 - 7

M S-7125 ATX M ainboard

4. Press Enter to continue with W indows XP Installation. Be sure to leave the floppy disk inserted in the floppy drive until the blue screen portion of W indows XP installation is completed, then take out the floppy.

5. Follow the instructions on how to install W indows XP. During the GUI portion of the install you might be prompted to click Yes to install the RAID driver. Click Yes as many times as needed in order to finish the installation. This will not be an issue with a signed driver.

MSI Reminds You...

Each time you add a new hard drive to a RAID array, the RAID driver will have to be installed under Windows once for that hard drive. After that, the driver will not have to be installed

5 - 8

nVIDIA RAID Introduction

Installing the NVIDIA RAID Software Under Windows

(for Non-bootable RAID Array)

The existing W indows IDE Parallel ATA driver (as well as the Serial ATA driver if SATA is enabled) must be upgraded to use the NVIDIA IDE Parallel ATA driver (as well as the

NV Serial ATA driver if SATA is enabled).

This section describes how to run the setup application and install the RAID software which will upgrade the W indows IDE driver and install the RAID software.

1. Start the nForce Setup program to open the NVIDIA W indows nForce Drivers page.

2. Select the modules that you want to install. Make sure that the

NVIDIA IDE Driver

” is selected.

3. Click Next and then follow the instructions.

4. After the installation is completed, be sure to reboot the PC.

5. After the reboot, initialize the newly created array.

5 - 9

M S-7125 ATX M ainboard

Initializing and Using the Disk Array

The RAID array is now ready to be initialized under W indows.

1. Launch Computer Management by clicking

Start

-->

Settings

-->

Control Panel

--> “ Switch to Classic View ” then open the “ Administrative Tools ” folder and double click on “ Computer Management ” .

2. Click “ Disk Management ” (under the “ Storage ” section). The Initialize and Convert

Disk W izards appears.

3. Click Next . The Select Disks to Initialize window appears. The disks listed depend on how many arrays you have configured.

4. Click Next . The Select Disks to Convert window appears.

5-10

nVIDIA RAID Introduction

5. Check the disk in the list if you want to make the array a dynamic disk, then click

Next . The Completing the Initialize and Convert Disk Wizard window appears.

6. Click Finish . The “ Computer Management ” window appears.

The actual disks listed will depend on your system, and the unallocated partition is the total combined storage of two hard disks. You must format the unallocated disk space in order to use it.

7 .

Format the unallocated disk space. Right click “ Unallocated space ” , select “ New

Partition …” and follow the wizard. After the drive has been formatted, it is ready for use.

5-11

M S-7125 ATX M ainboard

RAID Drives Management

There is an application called NVRAIDMAN which helps you perform the following tasks of nVDIA RAID.

• Viewing RAID Array Configurations

View an array configuration (mirrored, striped, mirror-striped, JBOD, or any supported combination)

• Setting Up a Spare RAID Disk

View free and/or dedicated free disks

• Designate a free disk to a particular array

• Rebuilding a RAID Mirrored Array

• Rebuild a broken mirrored array

• W atch the progress of rebuilding an array

Viewing RAID Array Configurations

To view your RAID configuration from W indows, launch the NVRAID Management utility by clicking Start-->Programs-->NVIDIA Corporation-->RAID Manager-->RAID

M a n a g e r ( t h e d e f a u l t l o c a t i o n o f N v R a i d M a n . e x e i s i n

\\nVidia\System\CK804\IDE\WinXP\raidtool or \\nVidia\System\CK804\ide\win2k\raidtool of the setup CD accompanied with your mainboard).

The RAID configuration information appears in the right-side pane, as shown below.

MSI Reminds You...

The information in the figures in this part may very from what it is shown in your system.

NVRAID M irrored Array

The figure below shows an example of a two hard drive mirrored array using identical 55.90 GB IDE hard drives (ST360015A), where one drive is configured as

Master and the other drive is configured as Slave. The total hard disk space used is

55.90 GB. (1.1 GB = 1,073,741,824 bytes)

5-12

nVIDIA RAID Introduction

NVRAID Striped Array

The figure below shows an example of a two hard drive striped array using identical

55.90 GB IDE hard drives (ST360015A), where one drive is configured as Master and the other drive is configured as Slave. The total disk space used is 111.80 GB.

NVRAID Striped Mirror Array

The figure below shows an example of a four hard drive stripe-mirrored array. The total disk space used is 111.80 GB.

NVRAID Spanning (JBOD) Array

The figure below shows an example of a two hard drive spanning array. The total disk space used is 111.80 GB.

NVRAID Mirrored Array and a Striped Array

The figure below shows an example of a two hard drive mirrored array as well as a two hard drive striped array.

5-13

M S-7125 ATX M ainboard

Setting Up a Spare RAID Disk

You can designate a hard drive to be used as a spare drive for a RAID 1 or RAID 0+1 array2. The spare drive can take over for a failed disk. NVRAID supports two types of spare drives:

• Free Disk

A free disk is a disk that is not part of any RAID array, but can be used by any available RAID 1 or RAID 0+1 array that requires a particular disk when one of its disks crashes or becomes unusable. The process is automatic and doesn

’ t require any user interaction.

For example, if you have a system with four hard disks where one disk is used to boot the OS, two hard drives are set up in a mirrored array, and a fourth hard disk is set up as a free disk, then if one of the mirrored array drives fails, the free disk will be automatically assigned to the mirrored array to be used instead of the failed disk.

• Dedicated Disk

A dedicated free disk is a disk that is assigned to a RAID 1 or RAID 0+1 array and that disk is used by that array only when needed, for example during a system crash where a RAID mirrored drive is broken. The dedicated disk can be used only by the array that it is assigned to and not by any other array, unlike a free disk which can be used by any available RAID 1 or RAID 0+1 array.

Assigning a Free Disk

To mark a disk as free, or not a part of any array,

1.

Enter the system BIOS setup and make sure that the drive that you want to mark as free is RAID enabled.

2.

Enter the RAID BIOS and make sure that the drive is not part of any array (if one exists).

3.

Boot into W indows and run the NVRAIDMAN program. The drive appears under the

Free Disk section. The figure below shows an example of the NVRAIDMAN display if you have a mirror array and one free disk.

5-14

nVIDIA RAID Introduction

Assigning a Dedicated Disk

To mark a disk as dedicated, or reserve it for use by a specific array,

Step 1: Mark the Disk as a Free Disk

1.

Enter the system BIOS setup and make sure that the drive that you want to mark as free is RAID enabled.

2.

Enter the RAID BIOS and make sure that the drive is not part of any array (if one exists).

3.

Boot into W indows and run the NVRAIDMAN program. The drive appears under the

Free Disk section.

Step 2: Dedicate the Free Disk to an Array

W hile running NVRAIDMAN, dedicate the free disk to an array using one of the following two methods:

• Method 1: Select a free disk and then assign it to an array.

• Method 2: Select an array and then assign a free disk to it.

Both methods are equally simple ways of accomplishing the same task.

M ethod 1: Select a free disk and then assign it to an array.

1. Right click one of the available disks under the Free Disk section. The pop-up menu

appears.

2. Select Designate Spare from the menu to launch the Spare Disk Allocation Wizard.

5-15

M S-7125 ATX M ainboard

3. Click Next .

The RAID Array Selection page appears.

4. From the RAID Array Selection page, select one of the arrays from the list.

This is the array to which you want to allocate the dedicated free disk.

5.

Click Next .

The Completing the NVIDIA Spare Disk Allocation page appears.

6.

Click Finish .

As shown in figure below, the ST380023AS drive is now a dedicated free disk in the mirrored array. If a system crash occurs that causes any of the two ST360015A drives to fail, the ST380023AS hard drive will take over and be used in the newly formed mirrored array.

Once a dedicated disk has been assigned to a particular array, it can be removed at any time. To remove the disk, right click on the dedicated disk and select the option to remove it.

5-16

nVIDIA RAID Introduction

M ethod 2: Select an array and then assign a free disk to it.

1.

Right click on the array to which you want to assign a dedicated free disk. The popup menu appears.

2. Select Designate Spare from the menu to launch the Spare Disk Allocation Wizard.

3 . Click Next. The Free Disk Selection page appears.

4. From the Free Disk Selection page, select one of the disks from the list. Please note that there can be more than one disk to choose from.

5-17

M S-7125 ATX M ainboard

5.

Click Next . The Completing the NVIDIA Spare Disk Allocation page appears.

6.

Click Finish .

You have now assigned a dedicated free disk to a mirrored array.

Once a dedicated disk has been assigned to a particular array, it can be removed at any time. To remove the disk, right click on the dedicated disk and select the option to remove it.

5-18

nVIDIA RAID Introduction

Example of Dedicating a Free Disk in a RAID 1 or RAID 0+1 Array

You can also assign a dedicated free disk to a RAID 1 or a RAID 0+1 array, using the same process.

1.

Right-click either the free disk that you want to dedicate to an array, the array type, or the array drives as shown in the figure below. Then click Designate Spare to launch the Spare Disk Allocation W izard.

2.

Click Designate Spare and then follow the instructions in the W izard. The figure below shows an example of a RAID 1 array that has one spare disk dedicated to it.

Once a dedicated disk has been assigned to a particular array, it can be removed at any time. To remove the disk, right click on the dedicated disk and select the option to remove it.

5-19

M S-7125 ATX M ainboard

Rebuilding a RAID Mirrored Array

Rebuilding is the process of recovering data from one hard drive to another. All data is copied from one hard drive to another and then the data is synchronized between the two hard drives. This only applies to RAID 1 array as well as a RAID 0+1 array.

Rebuilding Instructions

After creating a mirrored array, you can rebuild the array using the following steps:

1.

Go to Windows and run the NVRAID Management utility. The figure below shows an example of a system with one mirrored array.

2 . Right-click on Mirroring. The popup menu appears.

3.

From the popup menu, click Rebuild Array . The NVIDIA Rebuild Array W izard appears.

5-20

4 . Click Next. The Disk Selection page appears.

nVIDIA RAID Introduction

5. Select the drive that you want to rebuild by clicking it from the list, then click Next .

The Completing the NVIDIA Rebuild Array page appears.

6.

Click Finish . The array rebuilding starts after a few seconds, and a small pop-up message appears towards the bottom right corner of the screen as shown in the figure below.

During the rebuilding process, the NVRAID Management utility screen shows the status under the System Tasks and Details sections.

5-21

M S-7125 ATX M ainboard

M ore About Rebuilding Arrays

• Rebuilding Occurs in the Background

The rebuilding process is very slow (it can take up to a day) and occurs in the background so as not to affect the performance of the system.

Rebuilding Applies Only to RAID 1 or RAID 0+1 Arrays

Rebuilding an array works only when using RAID1 and/or RAID 0+1. Rebuilding does not apply to RAID 0 and JBOD arrays.

• You Can Use Any Available Free Disk

You can rebuild a mirrored array using any available Free Disk or Dedicated Disk.

For example, the figure below shows a mirrored array using 34.48 GB HD while having two Free Disks each 55.90 GB large.

To use one of these available free disks to rebuild your array, except when prompted to select a disk, choose one of the two available free disks.

5-22

Installation of Drivers and Utility

Chapter 6. Installation of Driver & Utility

Installation of

Drivers & Utility

MSI provides a setup CD along with your mainboard, which contains the required drivers for your system, and many other useful and powerful utility to bring you the best experience for your office professional working and for your home leisure entertainment.

6 - 1

M S-7125 ATX M ainboard

Driver Installation

Click on the Driver tab and the screen below will display. Click on the driver you like to install, and follow the proceeding instructions.

NVIDIA nForce4 System Driver

This driver is only available for W indows 2000 and W indows XP operating system.

Please follow the following step to install the driver correctly.

1. Click on this button to install the NVIDIA nForce4 System Drivers for your W indows

OS. Then the welcome dialogue will display. Click Next to continue.

6 - 2

Installation of Drivers and Utility

2. Then the following screen displays the available components to install. All the components shown here will be selected to be installed by default. Then click

Next .

3. The system will start installing the selected driver components automatically.

4. Then the following screen displays the information for the NVIDIA IDE SW Driver installation. Click Next to continue.

6 - 3

M S-7125 ATX M ainboard

5. Then the following screen displays the installation of NVIDIA IDE SW Driver. Click

Yes to continue.

6. The following screen indicates that the installation is complete. Click Yes to restart your computer or click No to restart it later.

6 - 4

MSI Reminds You...

The installation of NVIDIA Firewall and ForceWare Network Access

Manager. It is a software firewall to protect the softwares from hacking.

However, it is strongly suggested that you do not install this component.

Please follow the instruction below to make a software firewall CD for yourself.

1. Insert the MSI CD into the CD-ROM drive.

2. Ignore the Setup screen and use “ Explorer ” to browse the CD.

3. In the \\nVidia\System\C K804\Ether net\Firew all doubleclicking “ NewworkAccessManagerSetup ” file to install the software.

Installation of Drivers and Utility

Realtek AC97 Audio Driver

1. Click on this button to install the Realtek AC97 Audio Driver. Then the welcome dialogue will display. Click Next to continue. The installation process will launch automatically.

2. The following screen indicates the installation is complete. Click Yes to restart your computer or click No to restart it later.

6 - 5

M S-7125 ATX M ainboard

Utility Installation

Click on the Utility tab and the screen below will display. Click on the utility you like to install, and follow the proceeding instructions.

6 - 6

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents