Entry Delay. PARADOX ESPRIT 728 ULT, 738ULT

7.8

7.9

Entry Delay 1

Decimal Programming

D

Address 050

Default: 45 seconds

Any zone that has not been identified as either Instant Zones, Follow Zones, Entry Delay 2, or 24Hr and Fire Zones will automatically default to Delay 1. You can program the Delay 1 period between 001 and 255 seconds into address 050. If a zone defined as Delay 1 opens in an armed system, the control panel will wait the pre-programmed period of time before generating an alarm. This provides users with the time required to disarm the system when entering the protected area.

[ ENTER ] + Installer code + [0] [5] [0] + 3-digit decimal value (001 to 255) + [ ENTER ]

Entry Delay 2

728 Ultra: Feature Select Programming

D

Address 112; Keys [1] to [10 (0)]


D

Addresses 112 and 114; Keys [1] to [10 (0)], [ STAY ]/[11] and [ FORCE ]/[ AWAY ]/[12] )

Using Feature Select Programming on page 13, select which zones will be defined as Entry Delay 2 Zones. If a zone defined as

Delay 2 opens in an armed system, the control panel will wait for the duration of the Entry Time Delay 2 period (see page 29)

before generating an alarm. This provides users with the time required to disarm the system when entering the protected area.

7.9.1

Entry Time Delay 2


D

Address 051


This applies to all zones defined as Entry Delay 2 (see page 29). You can program the delay between 001 and 255

seconds.


7.10

Partitioning

Feature Select Programming

D

Address 086; Key [8]

Default: Disabled

This feature divides the alarm system into two distinct systems, identified as System A and System B. You can assign each zone to System A, System B, both systems, or neither system. Partitioning works as follows:

• Zones assigned to System A will arm/disarm when the system is System A Armed/Disarmed.

• Zones assigned to System B will arm/disarm when the system is System B Armed/Disarmed.

• Zones assigned to both systems (dual area) will arm when the system is either System A Armed, System B Armed or when both systems are armed and will disarm only when both systems disarm.

• Zones not associated with any system (common area) will arm only when the system is both System A Armed and System B

Armed and will only disarm when at least one of the two systems disarms.

For more information on arming or disarming partitions, see

Arming/Disarming Partitions on page 41. Also see

Code Priority on page 34.

7.10.1

System A/Stay Zones


D

Address 116; Keys [1] to [10 (0)]


D

Addresses 116 and 118; Keys [1] to [10 (0)], [ STAY ]/[11] and [ FORCE ]/

[ AWAY ]/[12] )

Using Feature Select Programming on page 13, select which zones will be assigned to System A, or if the system isn’t

partitioned, which zones will be identified as stay zones. For details on System A zones refer to

Partitioning above. See

Stay Arming on page 41 for more information.

7.10.2

System B Zones


D

Address 120; Keys [1] to [10 (0)]


D

Addresses 120 and 122; Keys [1] to [10 (0)], [ STAY ]/[11] and [ FORCE ]/

[ AWAY ]/[12] )

Using Feature Select Programming on page 13, select which zones will be assigned to System B. For details on

System B zones, refer to Partitioning above.

7.11

Bypass Enabled Zones


D

Address 124; Keys [1] to [10 (0)]


D

Addresses 124 and 126; Keys [1] to [10 (0)], [ STAY ]/[11] and [ FORCE ]/[ AWAY ]/[12] )

Using Feature Select Programming on page 13, select which zones will be defined as bypass enabled. Only zones defined as

bypass enabled can be used for manual zone bypassing (see

Manual Zone Bypassing on page 42) or during Auto Zone

Shutdown (see page 30).

Bypassed zones can automatically be reported to the monitoring station upon arming (738 Ultra only). Please see Ademco

Contact ID (All Codes) on page 19 for more information.

Esprit 728 Ultra & 738 Ultra 29

7.11.1

Auto Zone Shutdown


D

Address 086; Key [ TBL ] or [ TRBL ]

Default: Auto Zone Shutdown Disabled

The control panel will automatically bypass any bypass enabled zones which initiate 5 consecutive alarms in the samearmed period. Therefore, the zone will no longer generate an alarm. After the control panel has bypassed a zone, it will report an event code to the monitoring station if programmed at addresses 448 to 457 (728 Ultra) or 465 (738 Ultra).

The Auto Zone Shutdown counter resets when the system is disarmed.

This feature is also a function of the Report Zone Restore Options on page 24. If this option is set for report zone

restore on bell cut-off, the zone will only be bypassed after the bell or siren has cut off 5 consecutive times in the same armed period. While if the option is set for report zone on zone closure, the zone will be bypassed when the zone has opened and closed 5 consecutive times in one armed period.

Key [ TBL ]/[ TRBL ] OFF: Auto Zone Shutdown Disabled

Key [ TBL ]/[ TRBL ] ON: Auto Zone Shutdown Enabled

[ ENTER ] + Installer code + [0] [8] [6] + [ TBL ]/[ TRBL ] ON/OFF + [ ENTER ]

7.12

EOL Zones (Enabled/Disabled)


D

Address 088; Key [ MEM ]

Default: Enabled (No EOL)

If the system requires the use of 1k

9

end of line resistors on zone input terminals, disable this feature (see Keypad Zone

Connections on page 5 to

Single Zone Input Terminal Connections on page 6).

Key [ MEM ] OFF: Input Zones use EOL Resistors

Key [ MEM ] ON: Input Zones do not use EOL Resistors

[ ENTER ] + Installer code + [0] [8] [8] + [ MEM ] ON/OFF + [ ENTER ]

7.13

Keypad Zone 1 Supervision


D

Address 090; Key [ STAY ]


When using a keypad defined as Keypad Zone 1, enable this feature. When enabled, the control panel will verify the presence of

a keypad and the keypad zone. For more information see Keypad Zone Connections on page 5.

Key [ STAY ] OFF: Keypad Zone 1 Disabled

Key [ STAY ] ON: Keypad Zone 1 Enabled

[ ENTER ] + Installer code + [0] [9] [0] + [ STAY ] ON/OFF + [ ENTER ]

7.14

Keypad Zone 2 Supervision


D

Address 090; Key [ AWAY ]/[ FORCE ]


When using a keypad defined as Keypad Zone 2, enable this feature. When enabled, the control panel will verify for the presence

of a keypad and the keypad zone. For more information see Keypad Zone Connections on page 5.

Key [ AWAY ]/[ FORCE ] OFF: Keypad Zone 2 Disabled

Key [ AWAY ]/[ FORCE ] ON: Keypad Zone 2 Enabled

[ ENTER ] + Installer code + [0] [9] [0] + [ AWAY ]/[ FORCE ] ON/OFF + [ ENTER ]

30 Reference & Installation Manual

Arm/Disarm Related

Features

Part 8: Arm/Disarm and Alarm Options

Figure 29: Arming/Disarming Related Features

Auto Arm Time

Addresses 044 and 045

Timed Auto Arming

Address 086; key [5]

Auto Arming Options


No Movement Auto

Arming


No Movement Time

Address 055

Code Priority

Define which users can

System A/Stay Arm,

System B/Away (Force) Arm or Bypass zones

System A/Stay Arm

Priority

Addresses 062, 064 and

066; all keys

System B/Away Arm

Priority


072; all keys

Bypass Access


078; all keys

One Key Regular Arming


One Key System A/

Stay Arming


Keyswitch Arming

Address 086; keys [2] & [3]

Bell Squawk

Address 086; [ MEM ] key

Exit Delay

Address 049

Alarm Transmission

Delay

Address 059

Bell Cut-Off Time

Address 052

Beep on Exit Delay

Address 088; key [ AWAY ]/[ FORCE ]


8.1

8.2

8.3

Timed Auto Arming


D

Address 086; Key [5]

Default: Timed Auto Arming Disabled

The alarm system will automatically arm itself at a specified time every day. Please note that as with Regular arming, the system will not arm if a zone is open, but will always report a "late to close" to the monitoring station. If this occurs, the system will not arm until the next day. If arming is successful, the arming report codes and a “late to close” are both transmitted to the monitoring station. If arming is unsuccessful, only the “late to close” is sent to the monitoring station. The type of arming is dependent on the

Auto Arming Options (see

Auto Arming Options on page 32). Program the Auto Arm Time as described below:

8.1.1

8.1.2

Auto Arm Time

The control panel will automatically arm itself at the specified time if timed auto arming (see above) is enabled. The time is programmed using the 24-hour clock (i.e. 8:00 p.m. = 20:00). There are two methods of programming the auto arm time as described below.


D

Addresses 044 and 045

Program the Auto Arm Time in hours into address 044 and the Auto Arm Time in minutes into address 045.

[ ENTER ] + Installer code + [0] [4] [4] + 3-digit decimal value (hours) + [0] [4] [5] + 3-digit decimal value (minutes) + [ ENTER ]

Key Access Programming

D

Key [9]

The User 1, Master, or Installer can program the Auto Arm Time using this method.

[ ENTER ] + (Installer, Master or User code 1) + [9] + 2 digits representing hours + 2 digits representing minutes + [ ENTER ]

Auto Arming Options


D

Address 090; Key [2]

Default: Regular Arming

The Auto Arm feature will arm the system as described in Table 11.

Table 11: Auto Arming Options

Key [2]

OFF

OFF

ON

ON

Partitioning Options

OFF Regular Arming

ON Systems A and B Arming

OFF

ON

Stay Arming

System A Arming

[ ENTER ] + Installer code + [0] [9] [0] + [2] ON/OFF+ [ ENTER ]

No Movement Auto Arming


D

Address 086; Key [6]


If the control panel does not detect any movement (zone openings) for a specified period, the panel will arm the system and transmit the event code programmed at address 517. Please note that the type of arming is dependent on the Auto Arming

Options (see section 8.1.2). Program the No Movement Auto Arm Time as described below.

Key [6] OFF: No Movement Auto Arm Disabled

Key [6] ON: No Movement Auto Arm Enabled

[ ENTER ] + Installer code + [0] [8] [6] + [6] ON/OFF + [ ENTER ]

8.2.1

No Movement Auto Arm Time


D

Address 055


000 = disabled; (001 to 255) x 15 minutes

If the No Movement Auto Arming feature (see page 32) is disabled and a time is programmed, the control panel will

transmit the event code programmed at address 517 if no movement is detected during the programmed period.


One-Key Regular Arming


D

Address 088; Key [7]


A user can Regular arm the system by pressing and holding the [0] or [ ARM ] key for 2 seconds.

Key [7] OFF: One Key Regular Arming Disabled

Key [7] ON: One Key Regular Arming Enabled



8.4

8.5

8.6

8.7

8.8

8.9

One-Key Stay/System A Arming


D

Address 088; Key [8]


Press and hold the [ STAY ] key for 2 seconds to Stay arm the system if partitioning is disabled. If the system is partitioned, the control panel will arm System A.

Key [8] OFF: One Key Stay/System A Arming Disabled

Key [8] ON: One Key Stay/System A Arming Enabled


Arming Using a Keyswitch


D

Address 086; Keys [2] and [3]


The user can use a keyswitch to Stay arm or Regular arm/disarm the system. If the system is ready and the button is pressed, the system will arm. Pressing the button again will disarm the system. The keyswitch will not disarm a Stay armed system in alarm.

Refer to

Keypad and Keyswitch Connections on page 4 for installation of a keyswitch.

Table 12: Keyswitch Arming Table

Key [2]

OFF

ON

OFF

ON

Key [3] Function

OFF

OFF

ON

ON

Disabled

Disabled

Full Arming

Stay Arming *

* If partitioning is enabled, the keyswitch will arm System A only.

[ ENTER ] + Installer code + [0] [8] [6] + [2] and [3] ON/OFF + [ ENTER ]

Bell Squawk


D

Address 086; Key [ MEM ]


With this feature enabled, the bell or siren will emit a half-second squawk upon arming and two half-second squawks upon disarming.

Key [ MEM ] OFF: Bell Squawk Disabled

Key [ MEM ] ON: Bell Squawk Enabled

[ ENTER ] + Installer code + [0] [8] [6] + [ MEM ] ON/OFF + [ ENTER ]

Exit Delay


D

Address 049


The exit delay applies to all zones. This option determines how much time the user has to leave the protected area after entering a valid access code and before the system arms. You can program the exit delay from 001 to 255 sec.

[ ENTER ] + Installer code + [0] [4] [9] + 3 digit decimal value (001 to 255) + [ ENTER ]

Beep on Exit Delay


D

Address 088; Key [ AWAY ]/[ FORCE ]


With this feature enabled, the keypad will emit an intermittent beep during the programmed exit delay period (except when Stay arming). The frequency of intermittent beeps increases during the last 10 seconds of the exit delay period. For more information

about the exit delay refer to section 8.7.

Key [ AWAY ]/[ FORCE ] OFF: Beep on Exit Delay Disabled

Key [ AWAY ]/[ FORCE ] ON: Beep on Exit Delay Enabled

[ ENTER ] + Installer code + [0] [8] [8] + [ AWAY ]/[ FORCE ] ON/OFF + [ ENTER ]

Alarm Transmission Delay


D

Address 059


This time limit, set between 5 and 63 seconds, is the delay period before reporting an alarm to the monitoring station after an alarm condition. During this period, disarming the system will cancel all pending alarms and send the restore codes.

Programming 000 to 004 in this address disables this feature (Maximum 30 seconds on UL listed systems).



8.10

Silent Zones and Silent Panics Option


D

Address 086; Key [9]

Default: Generate a Silent Alarm

If the [9] key is on, silent zones or silent panics only transmit a report to the monitoring station. The system will not indicate an alarm and will not have to be disarmed. The control panel can still activate a PGM. If a keypad panic has been defined as audible, the control panel will override this option.

Key [9] OFF: Silent Zones and Silent Panics generate a silent alarm

Key [9] ON: Silent Zones and Silent Panics generate a report only


8.11

Bell Cut-Off Time


D

Address 052

Default: 5 minutes

After an audible alarm, the bell or siren will stop after the programmed time has elapsed.

[ ENTER ] + Installer code + [0] [5] [2] + 3-digit decimal value (001 to 255) minutes + [ ENTER ]

8.12

Code Priority


D

Addresses 062 to 078; [all] keys

In order for a user to arm a partitioned system, to Stay arm, to Force/Away arm or to manually bypass zones, the user must be given code priority. Using the

Feature Select Programming on page 13, identify which arming method each user can use. For

more information on arming/disarming methods please see User/Keypad Functions on page 40. Also refer to the

728 Ultra & 738

Ultra System Programming Guide for additional information.

Partitioning Disabled:

Addresses 062 to 066: Selected keys indicate which user codes can Stay arm.

Addresses 068 to 072: Selected keys indicate which user codes can Force/Away arm.

Addresses 074 to 078: Selected keys indicate which user codes can bypass zones.

Partitioning Enabled:

Addresses 062 to 066: Selected keys indicate which user codes can arm System A.

Addresses 068 to 072: Selected keys indicate which user codes can arm System B.

Addresses 074 to 078: Selected keys indicate which user codes can bypass zones.

8.13

Closing Delinquency Timer


D

Address 061 (Default: Disabled)


D

Address 090; Key [3] (Default: OFF)

At midnight everyday, the 728 Ultra and the 738 Ultra will verify when the system was last armed. If the last time the system was armed is greater than the programmed Closing Delinquency timer, the control panel will transmit a Closing Delinquency event (see

page 23) to the monitoring station. Depending on whether address 090 key

[3] is ON or OFF, the timer can be in days or hours.

The Closing Delinquency timer will be in days if address 090 key [3] is OFF and in hours if address 090 key [3] is ON. Enter 000 to disable the Closing Delinquency timer. Please note that the Closing Delinquency timer and event apply only to System A.

[ ENTER ] + Installer code + [0] [6] [1] + 3-digit decimal value (000 to 255) days/hours + [ ENTER ]

8.14

Restrict Arming on Battery Failure


D

Address 090; Key [4]


If this option is enabled, the control panel will not arm the system if the control panel detects that the backup battery is disconnected, the fuse is blown or the battery voltage drops below 10.5V. The control panel will not arm the system until all battery trouble conditions are rectified.


8.15

Restrict Arming on Tamper Trouble


D

Address 090; Key [5]


If this option is enabled, the control panel will not arm the system if the control panel detects a tamper trouble on one or more zones. The control panel will not arm the system until all tamper trouble conditions are rectified. The trouble can only be cleared by the installer entering programming mode.


This feature will not function if the Tamper Recognition Options (see page 38) are disabled. Only the installer can

clear the “Restrict Arming on Tamper” Trouble.


Part 9: PGMs (Programmable Outputs)

9.1

9.2

We strongly suggest using the Espload software to program the PGM(s).

PGM Types

Streamline - Sections 09

D

Hex Programming - Address 039

The 728 Ultra and 738 Ultra control panels have either one (728 Ultra) or two (738 Ultra) programmable outputs (PGMs). When a

PGM closes, a ground is supplied to activate any device or relay connected to it, providing up to a maximum of 50mA (UL 30mA).

When a PGM opens, the circuit is opened from ground, therefore not providing any power to devices connected to it. To program a PGM you must define the PGM state (normally open or normally closed), the timing (regular or timed) and you must define the type of logic ("OR", "AND", "EQUAL").

To program a PGM for the 728 Ultra, use Table 13 to determine which hex digit to program into address 039, where the first hex

digit programmed corresponds to the PGM. Press the [2 ND ] key for the second digit. For the 738 Ultra, use Table 13 to determine which hex digit to program into address 039, where the first hex digit programmed corresponds to PGM1 and the second hex digit corresponds to PGM2.

Regular N.O./N.C.

A triggered PGM will switch to its opposite state (i.e. closed to open or opened to closed). The PGM will return to its original state once the event(s) that triggered it have terminated.

Timed N.O./N.C.

A triggered PGM will switch to its opposite state (i.e. closed to open or opened to closed). The PGM will remain in its opposite state for the period programmed at address 056 (see

PGM Timer Setting on page 35). If the PGM is triggered again before the

period has elapsed, the PGM will remain in its opposite state and reset the timer.

"OR" Logic

Will trigger a PGM when at least one event occurs from a specific group of events (e.g. key [1] and/or key [2] is pressed on the keypad).

"AND" Logic

The "AND" logic will trigger a PGM when all events, or more, occur from a specific group of events (e.g. Keys [1] and [2] are pressed simultaneously. Note that pressing those two keys in conjunction with any other key will also trigger the PGM).

"EQUAL" Logic

The "EQUAL" logic will trigger a PGM only when the events from a specific group of events occur (e.g. Key [1] and [2] are pressed. Note the PGM will only trigger when pressing keys [1] and [2] simultaneously, if any other key is pressed at the same time (e.g. [1] , [2] and [3] ) the PGM will not trigger).

Table 13: PGM Type Selection

Key

[2 ND ] : OR

[1] : AND

[2] : EQUAL

Reg. N.O.

Key

[8]

[9]

[0]

: OR

: AND

: EQUAL

Reg. N.C.

[4]

[5]

: OR

: AND Timed N.O.

[6] : EQUAL

(For timed PGM, see address 056 in section 9.2.)

[ AWAY / FORCE ] : OR

[ BYP ] : AND

[ MEM ] : EQUAL

Timed N.C.

728 Ultra: [ ENTER ] + Installer code + [0] [3] [9]

+ first digit (see Table 13 above) +

[2 ND ] + [ ENTER ]

738 Ultra: [ ENTER ] + Installer code + [0] [3] [9] + first digit (PGM1) + second digit (PGM2) + [ ENTER ]

PGM Timer Setting


D

Address 056


You can program the PGM Timer from 1 to 127 seconds or from 1 to 127 minutes. The PGM timer applies to both PGMs. To determine the 3-digit decimal value, do the following:

• To program seconds, the required time is respective to the decimal value

1 second = 001, 55 seconds = 055, 127 seconds = 127.

• To program the minutes add the required minutes to 128:

5 minutes: 128 + 5 = 133

127 minutes: 128 +127 = 255



9.3

PGM Options

Streamline - Section 10

D

Hex Programming - Addresses 040 to 043

The PGM options define which sequence of events will trigger the PGM. The PGM options are virtually endless. Therefore, to list

them in a manual would be impractical. Table 14 (below) contains a list of the most commonly used PGM options with the

required 2-digit data for each address. If other options are required, you can fax your requests to Paradox Technical Support, you can visit our website at www.paradox.ca, or the 2-digit data can be derived using the Espload Software as follows:

1. Select Accounts from the Main Menu

2. Select a current Account or create a new one

3. Press the [ PAGE DOWN ] key from the keyboard until page 9 appears

4. Using the arrow keys and space bar select the PGM options, state, logic and type for the PGM

5. Press the [F8] key from the keyboard to view the Hexadecimal Mode. This mode will display the 2-digit data for addresses 039 to 043.

6. Record these numbers and program them into the control panel or use the Espload Software to download the data directly to the control panel.

If you do not have a copy of the Espload Software, you can obtain a free copy from your local Paradox distributor.

State Option

Table 14: Commonly Used PGM Options

PGM1

1st digit add. 039

[5] add. 040

[5] / [2] Timed N.O.

Output enabled for 3 seconds before communication attempt*

Regular N.O. Output enabled when keys [1] and [2] are pressed simultaneously

Regular N.O. Output enabled when system armed

Regular N.O. Output enabled during an alarm

Timed N.O.

Output enabled for 2 minutes upon fail to communicate

Regular N.O. Output enabled after one failed communication attempt

Timed N.O.

Output enabled for 3 seconds after signal received at monitoring station

[2

[2

[2

[1]

ND

ND

[5]

ND

[5]

]

]

]

[5] / [8]

[2] / [9]

[2] / [12]

[2] / [6]

[7] / [0]

[7] / [ BYP ]

[2 add. 042

[2

[2

[2

[2

[2

[2

ND

ND

ND

ND

ND

ND

] / [8]

] / [6]

] / [3]

] / [2]

] / [4]

] / [

ND

MEM

] / [8]

]

[2

[2

[2

[5]

[1]

ND

ND

[5]

ND

[5]

PGM2 (738 Ultra only)

2nd digit add. 039

]

]

] add. 041

[5] / [2]

[5] / [8]

[2] / [9]

[2] / [12]

[2] / [6]

[7] / [0]

[7] / [ BYP ]

[2 add. 043

[2

[2

ND ] / [8]

] / [6]

[2 ND ] / [3]

[2 ] / [2]

[2 ND ] / [4]

ND

[2

ND

ND

] / [

ND

MEM

] / [8]

]


Part 10: Other Options

10.1

Telephone Line Monitoring (TLM)


D

Address 086; Keys [2 ND ] and [1]

Default: TLM Disabled

When enabled, the system verifies the existence of a telephone line every 4 seconds. If the system detects a trouble, the LED will flash ON for 1 second and OFF for 1 second. TLM will activate a trouble when less than 3 volts is detected in four consecutive tests.

Please note that when the dialer detects a telephone ring, the TLM test stops for 1 minute. There are three TLM options, which

are set as indicated in Table 15 below:

Table 15: Telephone Line Monitoring (TLM)

Key

[2 ND ]

OFF

OFF

[1]

OFF

ON

- TLM is disabled (default)

- TLM generates a trouble only

ON

ON

OFF

ON

- generates an alarm if armed

- silent alarm becomes audible

(address 086, key [9] has to be OFF)

1.

OFF/ON: Line test failure will generate a trouble indication; key [0] will illuminate on the keypad (LED keypad only).

2.

ON/OFF: Line test failure will generate a trouble indication and an alarm if the system is armed.

3.

ON/ON: Line test failure will generate a trouble indication and cause a silent zone or a silent panic alarm to switch to audible mode.

[ ENTER ] + Installer code + [0] [8] [6] + [2 ND ] and [1] ON/OFF + [ ENTER ]

10.2

Dialing Options


D

Address 086; Key [7]

Default: Pulse Dialing

You can program the control panel to use the pulse dialing or tone/DTMF dialing format.

Key [7] OFF: Pulse Dialing

Key [7] ON: Tone/DTMF Dialing


10.3

Dialing Pulse Rates


D

Address 086; Key [0]

Default: Pulse Europe 1:2

This selection determines the ratio between "pulse" time and "quiet" time. Select Pulse Europe for a 1:2 ratio and select Pulse

USA for 1:1.5. Must be set to pulse dialing mode, refer to Dialing Options .

Key [0] OFF: Pulse Europe 1:2

Key [0] ON: Pulse USA 1:1.5


10.4

Keypad Panic Options


D

Address 088; Keys [1] to [6]


This feature will generate an alarm when the user presses two specific keys on the keypad simultaneously for 2 seconds as follows:

Key [1] ON = Panic 1 (keys [1] and [3] ) enabled



Keypad panic options:

Key [4] OFF = Panic 1 silent

Key [4] ON = Panic 1 audible


Key [5] ON = Panic 2 audible


Key [6] ON = Panic 3 fire alarm

[ ENTER ] + Installer code + [0] [8] [8] + [1] to [6] ON/OFF + [ ENTER ]


Silent operation:

When using the panic keys, the control panel will emit a single confirmation beep. The control panel will transmit the event codes programmed at addresses 513, 514 and 515. The alarm will latch (no audible alarm) and the light on the keypad will flash until the system is disarmed by a valid user code.

Audible operation:

Audible operation is the same as silent operation, except the alarm output (bell/siren) will activate until the system is disarmed by

a valid user code or until the Bell Cut-Off Time (see page 34) elapses.

Fire operation:

Fire operation is the same as audible operation except that bell/siren output will be pulsed (intermittent ON/OFF).

10.5

Panel Time


D

Key [ MEM ]

To program the current time into the control panel press:

[ ENTER ] + (Installer, Master, or User code 1) + [ MEM ] + 2 digits representing hours (00 to 23) + 2 digits representing minutes (00 to 59)

10.6

Time Correction

Streamline - Section 09

D

Hex Programming - Address 037 (2nd digit)

If you notice a gain or loss in the control panel time, calculate the average gain or loss per day; select the "opposite" amount from the Time Correction table in order to automatically correct the time setting every 24 hours.

Example: The control panel loses 4 minutes per month, representing an average loss of 8 seconds per day. Therefore, program

[2] (plus 8 seconds) as the second digit in address 037 to compensate for the 8-second loss.

Table 16: Time Correction Table

(address 037 2nd digit)

[2 ND ] - No adjustment

[1] - Plus 4 seconds







[8] - Minus 4 seconds



[ STAY ] - Minus 16 seconds

[ AWAY ]/[ FORCE ] - Minus 20 seconds

[ BYP ]

[ MEM ]

[ TBL / TRBL ]

- Minus 24 seconds

- Minus 28 seconds

- Minus 32 seconds

10.7

Tamper/Wire Fault Recognition Options


D

Address 088; Keys [0] and [ STAY ]


If the control panel detects an open or a short on a zone when the system is armed, regardless of the tamper/wire settings it will always generate an alarm and trouble indicator (key [9] ). Alarms will be audible or silent depending on individual zone definitions.

If an open or short occurs on a disarmed system, the control panel will generate an incident depending on the following settings.

Table 17: Tamper Recognition Option

Key [10 (0)] Key [ STAY ]

OFF OFF

OFF

ON

ON

ON

OFF

ON

- Tamper/Wire Fault disabled

- Trouble Indicator enabled

- Silent Alarm enabled

- Audible Alarm enabled

Tamper/Wire disabled

Tamper/wiring failure recognition is disabled. Not permitted on UL listed systems.

Trouble enabled

Tamper/wiring failure will generate a trouble indicator (key [9]

) and a trouble report code (see Tamper Codes on page 22) when

the system is disarmed.

Silent alarm enabled

Tamper/wiring failure will generate a trouble indicator (key [9]

), a trouble report code (see Tamper Codes on page 22) and a silent

alarm (no bells/sirens).

Audible alarm enabled

Tamper/wiring failure will generate a trouble indicator (key [9] ), a trouble report code (see

Tamper Codes on page 22) and an

audible alarm.

When the zone definition is 24Hr, the tamper definition follows the audible/silent alarm definition of the 24Hr zone.


10.8

Tamper Bypass Options


D

Address 090; Key [6]

Default: Generate alarm on bypassed zone tamper

With this option enabled, the control panel will not generate an alarm if a tamper is detected on a bypassed zone while the system is armed. With this option disabled, the control panel will generate an alarm if a tamper is detected on a bypassed zone while the system is armed.

Key [6] OFF: Generates an alarm if a tamper is detected on a bypassed zone

Key [6] ON: Ignores tamper if detected on a bypassed zone


10.9

Installer Test Mode


D

Key [8]

The Test Mode will allow you to perform walk tests where the bell or siren will squawk to indicate opened zones. To enter or exit the control panel Test Mode press:

[ ENTER ] + Installer code + [8] to enable (confirmation beep); press [8] again to disable (rejection beep)

10.10

Exclude Power Failure From Trouble Display


D

Address 090; Key [2 ND ]


Excludes the Power Failure, key [2]

, from the Trouble Display (see Trouble Display Monitoring on page 43).

10.11

Audible Trouble Warning


D

Address 090; Key [9]


Trouble conditions will cause the keypad to emit an intermittent beep. To silence the trouble warning, press the [ TBL ] / [ TRBL ] key.

10.12

Power Down Reset

Performing a power down reset will set the Installer and Master codes to factory default. Values entered at addresses 008 to 043,

062 to 124, 300 to 527 and all user codes will be set to factory defaults. Programmed values at addresses 003 to 007 do not change. To perform a reset, the installer lock must be disabled. To perform a power down reset perform the following:

1. Verify installer lock is disabled (see

Installer Lock on page 11).

2. Remove the battery and AC power from the control panel.

3. Remove all connected wires and devices from the PGM (PGM1 for 738 Ultra) and zone 1 terminals.

4. Short the PGM (PGM1 for 738 Ultra) and zone 1 terminals with a wire.

5. Reconnect the AC and battery power to the control panel.

6. Wait for 10 seconds and remove the wire.

Figure 30: Power Down Reset

1. Remove Power.

2. Remove all connected wires and devices from the PGM

(PGM1 for 738 Ultra) and zone 1 terminals.

3. Short the PGM (PGM1 for 738 Ultra) and zone 1 terminals.

4. Reconnect power.

5. Wait 10 seconds and remove wire.


Part 11: User/Keypad Functions

The innovative Esprit keypads take a new approach to security features and functions. Each numeral from 1 to 10 (728 Ultra) or 12 (738

Ultra) on the LED keypad represents each zone, from 1 to 10 (or 1 to 12) respectively, on the control panel. When using the LED keypad with the 738 Ultra, if the [2 ND ] key flashes, press the [2 ND ] key to view the status of zones 13 to 18 which are represented by keys [1] to [6].

When the zone light is OFF, the status in the protected zone is normal. If the zone light is ON, this means the zone is open. An LCD keypad will display the open zone numbers on the screen.

The light on the keypad will illuminate when the status of all the zones is normal (zones are closed). Therefore, all protected windows and doors must be closed and motion detectors must not detect any movement except those zones that have been bypassed.

Confirmation Beep: an intermittent series of beeps ("beep-beep-beep") indicates a successful keypad entry or system operation.

End/Rejection Beep: one long tone ("beeeeeeep") indicates incorrect keypad entry or unsuccessful system operation.

11.1

Programming Master and User Codes

The Esprit Ultra control panels have one Master code (00) and up to 48 user codes (01 to 48). The default Master code is

474747. The Master code can arm the system using any arming method, create/modify user codes and perform Key Access

Programming (see page 44). The User code 1 can create/modify access codes and perform key access programming. The

access code consists of either 4- or 6-digits and each digit can be any value from 0 to 9.

Do not enter [2 ND ] when programming the Master code as this will invalidate the Master code.

[ ENTER ] + Master or User code 1 + 2-digit code number (00 to 48) + 4 or 6-digit access code + [ ENTER ]

11.2

Regular Arming

This method, commonly used for day-to-day arming, will arm all the zones in the system. To Regular arm, the light must be illuminated, indicating that all zones are closed. All doors and windows must be closed, and there can be no movement in areas monitored by motion detectors. Once the light is on, a valid user access code must be entered. If a mistake is made entering the code or if the light is not on when the code was entered, the keypad will emit a rejection beep.

When the correct user access code is entered, the keypad will emit a confirmation beep and the light will illuminate. The

light will flash and the keypad will beep during the exit delay period (see Beep on Exit Delay on page 33). During the final 10

seconds of the exit delay, the keypad will beep and the light will flash at a faster rate. At the end of the exit delay, the keypad will emit a confirmation beep, the light will extinguish and the light will remain illuminated to indicate that the system is armed.

11.2.1

One-Key Regular Arming

To use this feature, enable the One-Key Regular Arming option (see page 32). When the

light is on, pressing and holding the [0] or [ ARM ] key for 2 seconds will arm all zones in the system. This feature can be used to allow specific individuals like service personnel (i.e. cleaners, maintenance) to arm the system when leaving the protected area, without giving them access to any other control panel operations. The use of a valid access code is still required to

disarm the system. For more information, see Regular Arming on page 40.

11.3

Force/Away Arming

To rapidly arm the system without having to wait for the light, simply press the [ FORCE ]/[ AWAY ] key followed by a valid access code. Once the exit delay expires, any open zones will be considered "deactivated" by the control panel. Therefore, these zones will not generate an alarm. If, while the system is armed, a "deactivated" zone closes, the control panel will change that zone to active status, generating an alarm if the zone is breached.

728 Ultra: If a mistake is made entering the code, the keypad will emit a rejection beep. When the correct user code is entered, the keypad will emit a confirmation beep and the light will illuminate. The light will flash and the keypad will beep during the exit delay period (see

Beep on Exit Delay on page 33). During the final 10 seconds of the exit delay, the keypad will beep and the

light will flash at a faster rate. At the end of the exit delay, the light will extinguish and the light will remain illuminated. If programmed at address 518, the control panel will send a partial arm report code to the monitoring station.

738 Ultra: If a mistake is made entering the code, the keypad will emit a rejection beep. When the correct user code is entered, the keypad will emit a confirmation beep and the light will illuminate. The light will flash and the keypad will beep during the exit delay period (see

Beep on Exit Delay on page 33). For the LED keypad, the

[ AWAY ] key will flash during the exit delay. During the final 10 seconds of the exit delay, the keypad will beep and the light will flash at a faster rate (LED keypad: the [ AWAY ] key will flash at a faster rate). At the end of the exit delay, the light will extinguish and the light will remain illuminated (LED keypad: the [ AWAY ] key will flash). If programmed at address 518, the control panel will send a partial arm report code to the monitoring station.

To use this method, the user must have force arming priority (see

Code Priority on page 34).


11.4

Stay Arming

Stay arming allows the user to remain in the protected area while partially arming the system. This means that the user can stay in and move around the establishment, while certain designated zones are armed. For example, entry/exit points like doors or windows, the basement, or perhaps all the zones on the perimeter of the establishment may be armed when going to sleep at

night, while the other zones remain deactivated. To program which zones will be activated when Stay arming the system, see

System A/Stay Zones on page 29.

Unlike Regular arming, the light does not have to be illuminated. Only doors and windows programmed as stay zones must be closed, and there can be no movement in areas monitored by motion detectors in stay zones. To Stay arm the system, press the

[ STAY ] key followed by a valid access code. If a mistake is made entering the code or if a stay zone is open when entering the code, the keypad will emit a rejection beep.

728 Ultra: After entering the correct user access code, the keypad will emit a confirmation beep, the light will flash and the

[ STAY ] key will illuminate (LED keypad only) during the exit delay period. During the final 10 sec. of the exit delay, the light will flash at a faster rate and the [ STAY ] key will remain illuminated (LED keypad only). At the end of the exit delay, the keypad will the ] key will remain illuminated (LED keypad only).

738 Ultra: After entering the correct user access code, the keypad will emit a confirmation beep, the light will flash and the

[ STAY ] key will flash during the exit delay period (LED keypad only). During the final 10 sec. of the exit delay, the light will flash at a faster rate and the [ STAY ] key will flash at a faster rate (LED keypad only). At the end of the exit delay, the keypad will emit a confirmation beep, the and lights and the [ STAY ] key will flash (LED keypad only).

To use this method, the user must be given Stay arming priority (see Code Priority on page 34).

11.4.1

One-Key Stay Arming

To use this feature, enable the One-Key Stay/System A Arming option (see page 33). When all stay zones are closed,

pressing and holding the [ STAY ] key for 2 seconds will arm only zones programmed as stay zones. For more information, refer to

Stay Arming on page 41.

11.4.2

One-Key Instant Arming

During the Stay arming exit delay (see Stay Arming on page 41), press and hold the

[ STAY ] key for 2 seconds until you hear a single beep. This will switch all entry delay zones to instant zones (see

Instant Zones

,

Entry Delay 1 and Entry

Delay 2 on page 29). Therefore, any entry delay zone that is breached will immediately generate an alarm instead of

waiting a pre-determined period.

11.4.3

Fast Exit

This feature is only available when the system is Stay armed (see Stay Arming on page 41). This feature will allow the

user to exit premises while the system is already armed and keep the system armed. This can be done one of two ways:

• With the system already Stay armed (after the exit delay), press and hold the [ STAY ] key for 2 seconds. The system will switch to exit delay mode ( light flashes), allowing time for the user to exit the premises. At the end of the exit delay period, the system will return to Stay arm mode.

• With the system already Stay armed, press and hold the [0] or [ ARM ] key for 2 seconds. The system will switch to exit delay mode ( light flashes). At the end of the exit delay period, the system will Regular arm the system (see

Regular Arming on page 40).

11.5

Arming/Disarming Partitions

Thanks to the partitioning feature, two distinct systems (A and B) can be created and controlled by the control panel. Partitioning can be used in installations where shared security systems are more practical, such as office/warehouse buildings, or apartment/ condominium complexes. Each zone can be assigned to System A, System B, both systems or given no system assignment.

User access codes can also be programmed to arm/disarm one system or both systems simultaneously (see

Code Priority on page 34). Unlike Regular arming, the

light does not have to be illuminated. All doors and windows pertaining to the desired system must be closed, and there can be no movement in areas monitored by motion detectors in the desired system.

1. If a user is not given any code priorities, the user will never be able to arm or disarm the system when partitioned.

2. If a user is given code priority to one of the two systems, entering the correct access code will arm or disarm the system to which the user was given priority.

3. If a user is given code priority to arm/disarm both systems A & B, it will function as follows:

• If the user enters the correct access code when Systems A and B are disarmed, it will completely arm both systems.

• If the user enters the correct access code when Systems A and B are armed, it will completely disarm both systems.

• When the system is partially armed, (i.e. only System A or only System B is armed) entering the correct access code will arm the other system.

• To arm/disarm each system separately, do the following:

Press [ STAY ] + [ VALID ACCESS CODE ] to arm/disarm System A.

Press [ AWAY ]/[ FORCE ] + [ VALID ACCESS CODE ] to arm/disarm System B.


If a mistake is made entering the code or if a zone in the desired system is open when entering the code, the keypad will emit a rejection beep. When the access code is correctly entered, the keypad will emit a confirmation beep. The keypad can display the status of both systems. For the LED keypad, when System A is armed, the [ STAY ] key and light will remain on. If System B is armed, the [ AWAY ]/[ FORCE ] key and light will remain on. When both systems are armed, all three lights will remain on. The

LCD keypad will directly display the partition status.

11.5.1

One-Key System A Arming

This feature allows the user to arm System A without the use of an access code. To use this feature, enable the One-

Key Stay/System A Arming option (see page 33). When all the zones in System A are closed, press and hold the

[ STAY ] key for 2 seconds to arm System A. This feature can be used to allow specific individuals like service personnel

(i.e. cleaners, maintenance) to arm the system when leaving the protected area, without giving them access to any

other control panel operations. For details on arming System A refer to Arming/Disarming Partitions on page 41.

11.6

System Disarming

The user must enter the protected area through a designated entry/exit point. The keypad will beep during the entry delay reminding the user to disarm the system. Upon entry of a valid access code, the light will extinguish and the keypad will emit a confirmation beep indicating that the system has been disarmed. If an incorrect access code is entered, the keypad will emit a rejection beep. Press the [ CLEAR ] key at any time to clear data and re-enter another access code. If an alarm was generated from a fire or 24Hr zone while the system was armed, entering a valid user code will silence the siren. However, you should then check the zone and eliminate the cause of the alarm. If you are unable to pinpoint the reason for the alarm, call your installer.

11.7

Alarm Memory

If an alarm condition occurs when the system is armed, the [ MEM ] key will turn on. A record of all alarm situations that occur is stored in memory. After disarming the system, pressing once on the [ MEM ] key will display which zones were open during the alarm period by illuminating the corresponding zone indicator(s) or by displaying it on the LCD screen depending on the type of keypad used. Please note that if the [ MEM ] key is pressed again when using LED keypads (636 and 646*) you will enter the event display which can only be decoded with a 642 LCD keypad. To exit the alarm memory display, press the [ CLEAR ] key. If using a

642* LCD keypad press the [ MEM ] key followed by the [ INFO ] key and use the [

S

] and [

T

] keys to scroll through the event list in memory. The alarms will remain in memory until the system is armed and disarmed without generating an alarm.

* Do not use the 646 LED and 642 LCD keypads for UL installations. Both the 646 LED keypad and the 642 LCD keypad are not UL listed.

11.8

Keyswitch or Pushbutton Arming/Disarming

A keyswitch or push button can be used to Stay (see

Stay Arming on page 41) or Regular (see

Regular Arming on page 40) arm/

disarm the system. If the system is ready and the button is pressed, the system will arm. Pressing the button again will disarm the system. If a Stay armed system is in entry delay or if an alarm has been generated while Stay armed, the keyswitch or push button cannot be used to disarm the system (if the keyswitch is programmed to Stay arm/disarm). In this case, only a keypad can disarm the system. In a partitioned system the keyswitch or push button will arm/disarm System A regardless of the System B

status. To enable this feature and set the options (Stay or Regular arming) refer to Arming Using a Keyswitch on page 33.

11.9

Manual Zone Bypassing

When a zone is bypassed it will no longer be monitored by the control panel, and hence, will not generate an alarm. A user may wish to bypass certain zones when, for example, workers are renovating part of the establishment or if a component in the system is damaged. Manual bypass arming instructs the control panel to ignore ("deactivate") specified zones in order to arm the remainder of the system. Verify that the following options are set in the control panel so that a user can manually bypass zones:

• You must first define which zones are Bypass Enabled Zones (see page 29). Zones not identified as Bypass Enabled cannot

be bypassed.

• Only users with the appropriate Code Priority (see page 34) can bypass zones.

• Please note, the control panel cannot bypass fire zones.

To bypass zones, press the [ BYP ] key followed by a valid access code. If the wrong code or a code without bypass priority is entered, the keypad will emit a rejection beep. If the correct code is entered, the [ BYP ] key will flash to indicate that you are now in bypass mode. If there are any currently bypassed zones, their respective zone indicators will turn on. Press the key corresponding to the zone you wish to bypass until their respective zone indicator turns on. If the zone you wish to bypass has not been programmed as bypass enabled, the corresponding zone indicator will never turn on. Press the [ CLEAR ] key to erase the current zone bypass entries and exit the bypass mode. If you have entered the correct bypass entries, press the [ ENTER ] key to accept these entries. The [ BYP ] key will remain on, denoting that zones in the system are currently bypassed, and hence, the next time the system is armed, certain zones will be bypassed. When the system is disarmed, the bypass entries will be erased.

11.10

Bypass Recall

This feature permits users to reinstate the last zone bypass entries saved in memory. When the system is disarmed, the bypass entries will be erased. To recall the previous bypass entries, while in the bypass mode, press the [ BYP ] and [ ENTER ] keys and the


previous bypass status will be re-established. This eliminates the need to re-enter the bypass entries every time the system is armed. If a user is in the process of entering new bypass entries on the keypad, pressing the [ BYP ] key will override new information and reinstate previous bypass entries.

11.11

Keypad Chime Zones (on LED Keypads)

A chimed zone advises you when a zone is opened by creating a rapid intermittent beep tone (beep-beep-beep-beep-beep). Up to six zones plus the local keypad zone can be programmed as chime zones. To turn on the chime zone feature, press and hold the key corresponding to the desired zone ( [1] to [6] ) for three seconds until the intermittent chime beep is heard. This means that the chime feature has been activated. If a continuous beep is heard, this means that the chime beep has been deactivated.

To enable the chime feature on the keypad zone, press and hold the [8] key for three seconds. To mute the keypad's alarm sounder, press and hold the [9] key for three seconds until the intermittent chime beep is heard. This means that the muting feature has been activated. If a continuous beep is heard, this means that the muting feature has been deactivated. If there is more than one keypad in the system, you must program each keypad’s chime zones separately. Keypad chimes must be reprogrammed if the panel suffers a total power loss.

Key [1] [6] : Turns chime ON or OFF in zones numbered 1-6

Key [8] :

Key [9] :

Turns chime ON and OFF for the local keypad zone

Turns the keypad's alarm sounder muting ON or OFF

11.12

Trouble Display Monitoring

Trouble conditions are continuously monitored by the control panel, which recognizes and displays 10 different trouble conditions on the keypad. When a trouble condition occurs, the [ TBL ]/[ TRBL ] key will illuminate and the keypad will emit an intermittent beep

if the Audible Trouble Warning (see page 39) is enabled. Press the

[ TBL ]/[ TRBL ] key to switch to trouble display mode. The [ TBL ]/

[ TRBL ] key will flash and any illuminated keys correspond to a current trouble condition as described below. Press any key to exit the trouble display mode.

11.12.1 No Battery/Low Battery - Key [1]

The control panel conducts a dynamic battery test under load every 60 seconds. The illumination of the [1] key indicates that the back-up battery is disconnected or that the battery should be replaced, as it will not provide adequate back-up current in case of AC loss. If the control panel is currently running on battery power, the illumination of the [1] key indicates that the battery voltage has dropped to 10.5 volts or lower.

11.12.2 Power Failure - Key [2]

The control panel will detect a power loss if a continuous loss of AC (less than or equal to 12.5V) has occurred during the period between two AC power tests (64 to 116 seconds). If a power loss remains present throughout the Power Failure

Report Delay (see page 24), the panel will transmit the report code programmed at address 499 and the

[ TBL ]/[ TRBL ] key will flash rapidly indicating a power failure. The trouble indicator is restored if AC is detected during the dynamic battery test and the panel will then transmit the report code programmed at address 507. You can remove the power failure trouble

indicator from the trouble display by enabling the Exclude Power Failure From Trouble Display option (see page 39).

11.12.3 Bell Disconnected - Key [4]

The illumination of the [4] key indicates that there is no bell or siren connected to the bell output terminals of the panel.

Please note that when connecting a bell or siren to an optional relay output the trouble indicator will always be on. To avoid this, connect a 1k

9

resistor across the bell output. The control panel only recognizes bells or siren connected directly to the bell output of the control panel—not those connected through a relay.

11.12.4 Maximum Bell Current - Key [5]

The bell output is microprocessor controlled and will automatically shut down when the current exceeds 3A. If this occurs, the [5] key will illuminate. After opening the short or reducing the load, the bell current is restored upon the following alarm generation.

This trouble indicator will only appear when the bell is activated (i.e. during an alarm).

11.12.5 Maximum Auxiliary Current - Key [6]

The illumination of the [6] key indicates that the auxiliary current has exceeded 650mA (728 Ultra) or 700mA (738

Ultra). This will cause an automatic shutdown of the auxiliary output. After opening the short or reducing the load, the panel will restore power to the auxiliary output following the dynamic battery test (approximately 60 seconds).

11.12.6 Communicator Report Failure - Key [7]

If the control panel was unsuccessful while attempting to communicate with the monitoring station computer or the

Espload software, the [7] key will illuminate. This trouble is automatically cleared when the [ TBL ]/[ TRBL ] key is pressed and the user has exited from the Trouble Display.


11.12.7 Timer Loss - Key [8]

The illumination of the [8] key indicates that the control panel’s internal clock must be reprogrammed. To reprogram the timer press:

[ ENTER ] + (Installer, Master or User code 1) + [ MEM ] + 2 digits (00 to 23) representing hours + 2 digits (00 to 59) representing minutes + [ ENTER ]

11.12.8 Tamper/Zone Wiring Failure - Key [9]

If the Tamper/Wire Fault Recognition Options (see page 38) are enabled, the

[9] key will illuminate to indicate a short or cut on a zone input. In order to provide line short recognition the zone connections must have EOL resistors (see

Keypad Zone Connections

on page 5 to Single Zone Input Terminal Connections on page 6).

11.12.9 Telephone Line Monitoring - Key [0]

If the Telephone Line Monitoring (TLM) feature (see page 37) is enabled, the

[0] key will illuminate to indicate that the control panel has not detected the presence of a telephone line for 30 seconds.

11.12.10 Fire Loop Trouble - Key [

STAY

]

The illumination of the [ STAY ] key indicates a wiring problem (line open) on zone 3 (or zone 5 with 2-wire smoke and

ATZ for 728 Ultra), if identified as a fire zone (see

24Hr and 4-Wire Smoke Detector Fire Zones

and

2-Wire Smoke

Detector Recognition (Input 3) on page 28).

11.13

Key Access Programming

This method allows for quick programming of features without entering addresses or section numbers. The following features are programmed using the Installer code as well as the Master code and User code 1.

Key

[9]

[ MEM ]

[ BYP ]

[ TBL ] / [ TRBL ]

[ AWAY ] / [ FORCE ]

[ STAY ]

[8]

Features

Auto Arm Time: for details see page 32

Panel Time: for details see page 38.

Manual Test Report: for details see page 24

Call Espload: for details see page 15

Answer Espload: for details see page 15

Cancel Communication: for details see page 15

Installer Test Mode: for details see page 39.


Important Information

This equipment complies with Part 68 of the FCC rules subpart D and CS-

03. Inside the cover of this equipment is a label that contains, among other information, the FCC registration number of this equipment.

Notification to Telephone Company

Upon request, customer shall notify telephone company of particular line to which the connection will be made, and provide the FCC registration number and the ringer equivalence of the protective circuit.

FCC Registration Number: 5A7AL01B728ULT

Ringer Equivalence Number: 0.1B (U.S. & Canada)

USOC Jack: RJ31X (USA), CA31A (CANADA)

Telephone Connection Requirements

Except for telephone company provided ringers, all connections to the telephone network shall be made through standard plugs and telephone company provided jacks, or equivalent, in such a manner as to allow for easy, immediate disconnection of terminal equipment. Standard jacks shall be so arranged that, if plug connected thereto is withdrawn, no interference to operation of equipment at customer's premises which remains connected to telephone network shall occur by reason of such withdrawal.

Incidence of Harm

Should terminal equipment/protective circuitry cause harm to telephone network, telephone company shall, where practicable, notify customer that temporary disconnection of service may be required; however, where prior notice is not practicable, the telephone company may temporarily discontinue service if action is deemed reasonable in circumstances. In case of temporary discontinuance, telephone company shall promptly notify customer and will be given opportunity to correct the situation.

Changes in Telephone Company Equipment or Facilities

The telephone company may make changes in its communication facilities, equipment operations or procedures, where such actions are reasonably required and proper in its business. Should any such changes render customer's terminal equipment incompatible with the telephone company facilities, the customer shall be given adequate notice to effect the modifications to maintain uninterrupted service.

General

This equipment shall not be used on coin telephone lines. Connection to party line service is subject to state tariffs.

Ringer Equivalence Number (REN)

The ren is useful to determine the quantity of devices that you may connect to your telephone line and still have all of those devices ring when your telephone number is called. In most, but not all areas, sum of the ren's of all devices connected to one line should not exceed five (5.0). To be certain of the number of devices that you may connect to your line, you may want to contact your local telephone company.

Equipment Maintenance Facility

If you experience trouble with this telephone equipment, please contact facility indicated below for information on obtaining service or repairs. The telephone company may ask that you disconnect this equipment from network until problem is corrected or until you are sure that the equipment is not malfunctioning.

FCC Part 15, Warnings Information to User

This equipment has been tested and found to comply with the limits for

Class B digital devices, pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and, if not installed and used in accordance with

Warnings

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to equipment intermittently, the user is encouraged to try to correct the interference by one or more of the following measures: (1) re orient or relocate the receiving antenna; (2) increase the separation between the equipment and receiver; (3) connect the equipment to an outlet on a circuit other than the one to which the receiver is connected, or (4) consult the dealer or an experienced radio/tv technician for assistance.

Caution:

Changes or modifications not expressly approved by PARADOX

SECURITY SYSTEMS could void the user's authority to operate the equipment.

Warranty

Paradox Security Systems Ltd. (“Seller”) warrants its products to be free from defects in materials and workmanship under normal use for a period of one year. Except as specifically stated herein, all express or implied warranties whatsoever, statutory or otherwise, including without limitation, any implied warranty of merchantability and fitness for a particular purpose, are expressly excluded. Because Seller does not install or connect the products and because the products may be used in conjunction with products not manufactured by Seller , Seller cannot guarantee the performance of the security system and shall not be responsible for circumstances resulting from the product’s inability to operate.

Seller obligation and liability under this warranty is expressly limited to repairing or replacing, at Seller's option, any product not meeting the specifications.

Returns must include proof of purchase and be within the warranty period.

In no event shall the Seller be liable to the buyer or any other person for any loss or damages whether direct or indirect or consequential or incidental, including without limitation, any damages for lost profits stolen goods, or claims by any other party, caused by defective goods or otherwise arising from the improper, incorrect or otherwise faulty installation or use of the merchandise sold.

Notwithstanding the preceding paragraph, the Seller’s maximum liability will be strictly limited to the purchase price of the defective product. Your use of this product signifies your acceptance of this warranty.

BEWARE: Dealers, installers and/or others selling the product are not authorized to modify this warranty or make additional warranties that are binding on the Seller.

Attachment Limitation Notice

The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company.

The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electrical inspection


authority, or electrician, as appropriate.

The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the Load Numbers of all of the devices does not exceed 100.

Industry Canada certification is only applicable to installation of devices which include transformers approved by the Canadian Standards

Association (CSA).

Requirements and Guidelines for UL Installations

UL has only evaluated the 728ULT for compatibility with the

Ademco model 685, FBI model CP220FB, SUR-GUARD SG-

MLR2-D6 and Silent Knight model 9000.

UL listed in accordance with standard UL1023 (Household Burglar

- Alarm System Units), standard UL985 (Household Fire Warning

Units) and UL1635 (Digital Alarm Communicator System Units).

Look for the UL mark on the product. Only products bearing this mark are UL listed.

Some operational features are not permitted in UL installations. To respect the standards for household applications, the installer should follow these guidelines when configuring the system.

1. All components of the system should be UL listed for the intended application.

2. If the installation is a FIRE ALARM application, refer to NFPA Standard

74 for details on smoke detector locations. There must be at least one

UL-Listed Indoor Fire Alarm Warning Signalling Appliance.

3. For UL/cUL Burglar Applications:

Maximum entry time = UL 45 seconds/cUL 60 seconds

Maximum exit time = UL 60 seconds/cUL 120 seconds

Minimum bell cutoff time = 5 minutes

4. Keypad Models 639, 642 and 646 are not UL/cUL listed. Do not use the

708 or Esprint with a UL installation--they are not UL listed.

5. The upload/download software should not be used on UL listed systems.

6. All outputs are Class 2 or power-limited, except for the battery terminal.

The Class 2 and power-limited fire alarm circuits shall be installed using

CL3, CL3R, CL3P or substitute cable permitted by the National Electrical

Code, ANSI/NFPA 70.

Label: US: 5A7AL01B728ULT

Filing Type: New Filing

Product Identifier: 728ULT

Equipment Code: AL

Network Address Signal Code: E

Country of Origin: CANADA (CAN)

AC Ringer Equivalent Number: 01B

USOC Jacks: RJ31X

Equipment Description: Control panel for residential burglar and fire warning systems

Rechargeable Acid/Lead or Gel Cell Backup Battery: 12Vdc, 4Ah/

7Ah; UL/cUL: 12Vdc, 7Ah only

Transformer: Universal, Model No. UB1640W, 16.5Vac (50-60Hz)

20VA minimum (40VA recommended). Do not connect the transformer to a switch-controlled outlet.

Bell/Siren: UL/cUL Wheelock 46T-12

Aux Power: 450mA (fuseless shutdown at 650mA); UL: 200mA maximum for 24Hr stand-by

Smoke Detector: 2-wire Hochicki model SLR 835BH-2 (see

page 10 for more information)

Warning : For UL installations, the metallic enclosure must be grounded to the cold water pipe or to the grounding rod.

UL/cUL: All outputs are Class 2 or power-limited, except for the battery terminal. The Class 2 or power-limited fire alarm circuits shall be installed using CL3, CL3R, CL3P or substitute cable permitted by the National Electrical Code, ANSI/NFPA 70.

Requirements and Guidelines for AUSTEL Installations

Austel-approved installations: use a transformer approved by the

State Electricity commission, such as "Dyen" PA series 15Vac

22VA. With this transformer, do not exceed the following maximum currents:

- maximum Auxiliary current (including keypads): 300mA

- maximum Bell current: 600mA

Requirements and Guidelines for cUL Installations

When the system controls a fire alarm system, wiring method must correspond to section 32 of the Canadian Electrical Code.

Look for the cUL mark on the product. Only products bearing this mark are cUL listed.738 Ultra is not UL listed.

Rechargeable Acid/Lead or Gel Cell Backup Battery: 12Vdc, 4Ah/

7Ah; UL/cUL: 12Vdc, 7Ah only

Transformer: Universal, Model No. UB1640W, 16.5Vac (50-60Hz)

20VA minimum (40VA recommended). Do not connect the transformer to a switch-controlled outlet.

Bell/Siren: UL/cUL Wheelock 46T-12

Aux Power: 450mA (fuseless shutdown at 650mA); UL: 200mA maximum for 24Hr stand-by

Smoke Detector: 2-wire Hochicki model SLR 835BH-2 (see

page 10 for more information)

© 2003-2005 Paradox Security Systems Ltd. Esprit and Ultra are trademarks or registered trademarks of Paradox Security Systems

Ltd. and its affiliates in Canada, the United States and other countries. All rights reserved. Specifications may change without prior notice. One or more of the following patents may apply:

6215399, 6111256, 5751803, 5721542, 5287111, 5119069,

5077549, 5920259 5886632. Canadian and international patents may also apply.


Index

Numerics

24Hr Zones

........................................................................28

2-Wire smoke detector

Connections

..................................................................10

Recognition

...................................................................28

4-Wire smoke detector connections

......................................10

A

About this manual

.................................................................1

AC Power

............................................................................2

Access Codes

....................................................................11

Access Programming, Key

...................................................44

Account Codes, System

......................................................19

Alarm Codes

......................................................................22

Alarm Memory

....................................................................42

Alarm Relay Ouputs

..............................................................4

Alarm Transmission Delay

...................................................33

Answer Espload

.................................................................15

Answering Machine Override Options Table

..........................14

Anti-Tamper Switch

..............................................................6

Arming

Away

...........................................................................40

Codes

..........................................................................22

Force

...........................................................................40

One-Key. See One-Key

Partitions

......................................................................41

Pushbutton

....................................................................42

Regular

........................................................................40

Stay

............................................................................41

Using a Keyswitch

.....................................................33

, 42

ATZ

...................................................................................27

ATZ Connections

..................................................................7

ATZ Parallel Wiring

...............................................................9

Audible Trouble Warning

.....................................................39

Auto Arm Time

...................................................................32

Auto Arming Options

...........................................................32

Auto Arming Options Table

..................................................32

Auto Test Report

................................................................23

Auto Zone Shutdown

..........................................................30

Automatic Event Buffer Transmission

...................................15

Auxiliary Power Terminals

.....................................................3

Away Arming

......................................................................40

B

Backup Battery

.....................................................................2

Battery Test

.........................................................................3

Battery, Backup

....................................................................2

Beep

Confirmation

..................................................................40

On Exit Delay

.................................................................33

Rejection

......................................................................40

Bell Cut-off Time

.................................................................34

Bell Output

...........................................................................4

Bell Squawk

.......................................................................33

Bypass

Enabled Zones

...............................................................29

Manual Zone

.................................................................42

Recall

..........................................................................42

Tamper, Options

.............................................................39

C

Call Back

........................................................................... 15

Call Espload

....................................................................... 15

Cancel Communication

....................................................... 15

Chime Zones, Keypad

......................................................... 43

Closing Delinquency Timer

.................................................. 34

Code Priority

...................................................................... 34

Commonly Used PGM Options Table

...................................36

Communicator Formats

Ademco Contact ID

All Codes

............................................................... 19

Programmable Codes

................................................ 20

Ademco Express

............................................................ 21

Pager

........................................................................... 21

Standard Pulse Formats

................................................... 21

Communicator Formats Table

........................................19

, 21

Computer Telephone Number

.............................................. 15

Connecting an Anti-Tamper Switch on an LED Keypad

............. 6

Connecting Programmable Outputs

........................................ 4

Contact ID Event Codes Table

............................................. 19

Current Consumption Table

................................................... 3

D

Decimal Programming

......................................................... 13

Delinquency Timer

.............................................................. 34

Dialing Options

................................................................... 37

Dialing Pulse Rates

............................................................ 37

Disarming

Partitions

...................................................................... 41

Pushbutton

.................................................................... 42

System

......................................................................... 42

Using a Keyswitch

........................................................... 42

Disarming Codes

................................................................22

Double Reporting

............................................................... 17

Double Zone Input Connections. See ATZ Connections

Duress Code

...................................................................... 11

E

Earth Ground

....................................................................... 2

Entry Delay 1

..................................................................... 29

Entry Delay 2

..................................................................... 29

EOL Zones

........................................................................ 30

Espload Software

............................................................... 12

Event Reporting

................................................................. 16

Exclude Power Failure from Trouble Display

.......................... 39

Exit Delay

.......................................................................... 33

F

Fast Exit

............................................................................ 41

Feature Select Programming

............................................... 13

Fire Circuit

Standard Installation

........................................................ 10

UL/ULC Installation

......................................................... 10

Fire Zones

......................................................................... 28

Follow Zones

..................................................................... 28

Force Arming

..................................................................... 40

G

Ground

................................................................................ 2


H

Hexa Programming

............................................................. 12

Hexa Streamlined Section Programming

............................... 13

I

Input Connections

For Single Zones. See Single Zone Connections

For Zone Doubling. See ATZ Connections

Installer

Code

........................................................................... 11

Lock

............................................................................ 11

Test Mode

.................................................................... 39

Instant Zones

..................................................................... 28

Intellizone Time Delay

......................................................... 27

Intellizones

........................................................................ 27

K

Key Access Programming

................................................... 44

Keypad

Chime Zones

................................................................. 43

Connections

.................................................................... 4

Function Test

................................................................... 3

Panic Options

................................................................ 37

Zone 1 Supervision

......................................................... 30

Zone 2 Supervision

......................................................... 30

Zone Connections

............................................................. 5

Zone Recognition Table

..................................................... 6

Keyswitch

Arming

................................................................... 33 ,

42

Arming Table

................................................................. 33

Connections

.................................................................... 4

Disarming

..................................................................... 42

L

LED, Status

....................................................................... 11

Location and Mounting

.......................................................... 2

M

Manual Test Report

............................................................ 24

Manual Zone Bypassing

...................................................... 42

Master Code

...................................................................... 11

Lock

............................................................................ 11

Programming

................................................................. 40

Memory, Alarm

................................................................... 42

Monitoring Station Telephone Number 1

............................... 18

Monitoring Station Telephone Number 2

............................... 18

Mounting

............................................................................. 2

N

No Movement Auto Arm Time

.............................................. 32

No Movement Auto Arming

.................................................. 32

O

One-Key

Double Stay Arming

........................................................ 41

Regular Arming

........................................................ 32 ,

40

Stay Arming

............................................................ 33 ,

41

System A Arming

...................................................... 33 ,

42

Other Options

.................................................................... 37

P

Pager

Delay

........................................................................... 21

Format Transmission Options

............................................ 21

Report Event Options

...................................................... 21


Reporting Format

............................................................ 21

Panel

Answer Options

.............................................................. 14

Identifier

....................................................................... 14

Settings for Espload

........................................................ 14

Time

............................................................................ 38

Panic

Codes

.......................................................................... 23

Keypad Options

............................................................. 37

Silent Option

................................................................. 34

Parallel Wiring, ATZ

.............................................................. 9

Partition Arming / Disarming

................................................ 41

Partitioning

........................................................................ 29

PC Password

..................................................................... 14

PGM Options

..................................................................... 36

PGM Timer Setting

............................................................. 35

PGM Type Selection Table

.................................................. 35

PGM Types

AND Logic

.................................................................... 35

EQUAL Logic

................................................................. 35

OR Logic

...................................................................... 35

Regular N.O. / N.C.

......................................................... 35

Timed N.O. / N.C.

........................................................... 35

PGMs, Programming

.......................................................... 35

Power

................................................................................. 2

Power Down Reset

............................................................. 39

Power Failure Report Delay

................................................. 24

Programmable Outputs

Connecting

..................................................................... 4

Programming Master and User Codes

.................................. 40

Programming Methods

Espload Software

........................................................... 12

Keypad


............................................... 13


....................................... 13

Hexa Programming

................................................... 12

Hexa Streamlined Section Programming

........................ 13

Programming PGMs

........................................................... 35

Programming, Key Access

.................................................. 44

Pulse Rates, Dialing

........................................................... 37

Pushbutton Arming / Disarming

............................................ 42

R

Recent Close Delays

.......................................................... 24

Regular Arming

.................................................................. 40

Regular Reporting

.............................................................. 17

Report Code Disarming Options

........................................... 24

Report Zone Restore Options

.............................................. 24

Reporting Disabled

............................................................. 17

Reporting Event Codes

Alarm Codes

................................................................. 22

Arming Codes

................................................................ 22

Disarming Codes

............................................................ 22

Restore Codes

............................................................... 22

Special Codes

............................................................... 23

Tamper Trouble Codes

.................................................... 22

Trouble / Trouble Restore Codes

........................................ 23

Zone Shutdown Codes

..................................................... 22

Reporting Options

Bypass Reporting

........................................................... 19

Double Reporting

............................................................ 17

Regular Reporting

........................................................... 17

Reporting Disabled

......................................................... 17

Split Reporting

............................................................... 17

Reporting Options Table

..................................................... 17

Reset to default

.................................................................. 39

Restore Codes

...................................................................22

Restrict Arming

On Battery Failure

...........................................................34

On Tamper Trouble

.........................................................34

S

Serial Output Connector

......................................................10

Shutdown Codes, Zone

.......................................................22

Silent Panics Option

............................................................34

Silent Zone Options

............................................................34

Silent Zones

.......................................................................27

Single Zone Connections

.......................................................6

Siren Output

.........................................................................4

Smoke detector connections

2-wire

..........................................................................10

4-wire

..........................................................................10

Special Codes

....................................................................23

Specifications

.......................................................................1

Split Reporting

...................................................................17

Squawk, Bell

......................................................................33

Status LED

........................................................................11

Stay Arming

.......................................................................41

System A / Stay Zones

........................................................29

System Account Codes

.......................................................19

System B Zones

.................................................................29

System Disarming

..............................................................42

T

Tamper / Wire Fault Recognition Options

..............................38

Tamper Bypass Options

......................................................39

Tamper Codes

...................................................................22

Tamper Fault Recognition Options

.......................................38

Tamper Recognition Table

...................................................38

Telephone Line Connection

...................................................3

Telephone Line Monitoring (TLM)

.........................................37

Telephone Line Monitoring Table

.........................................37

Telephone Number Special Instructions Table

.................18

, 22

Test

Battery

...........................................................................3

Keypad Function

...............................................................3

Test Report

Auto

............................................................................23

Manual

.........................................................................24

Test Transmission, Timed

...................................................24

Time Correction

..................................................................38

Time Correction Table

.........................................................38

Timed Auto Arming

.............................................................32

Timed Test Transmission

....................................................24

Trouble Codes

...................................................................23

Trouble Display Monitoring

..................................................43

Trouble Restore Codes

.......................................................23

Troubles

Bell Disconnected

...........................................................43

Communicator Report Failure

............................................43

Fire Trouble

...................................................................44

Maximum Auxiliary Current

................................................43

Maximum Bell Current

......................................................43

No Battery / Low Battery

...................................................43

Power Failure

................................................................43

Tamper / Zone Wiring Failure

.............................................44

Telephone Line Monitoring (TLM)

........................................44

Timer Loss

....................................................................44

U

User / Access Code Length

.................................................11

User / Keypad Functions

..................................................... 40

User Code Programming

..................................................... 40

User Codes

........................................................................ 11

W

Wire Fault Recognition Options

............................................ 38

Z

Zone 4

............................................................................... 28

Zone Bypassing, Manually

................................................... 42

Zone Definitions

................................................................. 25

Zone Recognition Table, Keypad

............................................ 6

Zone Shutdown Codes

........................................................ 22

Zone Speed

....................................................................... 27


Notes

For technical support in Canada or the U.S., call 1-800-791-1919 for English or 1-866-912-0600 for French, Monday to Friday, 8:00 a.m. to 8:00 p.m. EST.

For technical support outside Canada and the U.S., call 00-1-450-491-7444, Monday to Friday from 8:00 a.m. to 8:00 p.m. EST.

Please feel free to visit our website at www.paradox.ca.

780 Industriel Blvd., Saint-Eustache (Quebec) J7R 5V3 CANADA

Tel.: (450) 491-7444 Fax: (450) 491-2313 www.paradox.ca

PRINTED IN CANADA - 03/2005 7X8ULT-EI01

Entry Delay. PARADOX ESPRIT 728 ULT, 738ULT 56 Pages

Entry Delay. PARADOX ESPRIT 728 ULT, 738ULT

7.8

7.9

Entry Delay 1

Entry Delay 2

7.9.1

Entry Time Delay 2

7.10

Partitioning

7.10.1

System A/Stay Zones

7.10.2

System B Zones

7.11

Bypass Enabled Zones

7.11.1

Auto Zone Shutdown

7.12

EOL Zones (Enabled/Disabled)

7.13

Keypad Zone 1 Supervision

7.14

Keypad Zone 2 Supervision

Part 8: Arm/Disarm and Alarm Options

8.1

8.2

8.3

Timed Auto Arming

8.1.1

8.1.2

Auto Arm Time

Auto Arming Options

No Movement Auto Arming

8.2.1

No Movement Auto Arm Time

One-Key Regular Arming

8.4

8.5

8.6

8.7

8.8

8.9

One-Key Stay/System A Arming

Arming Using a Keyswitch

Bell Squawk

Exit Delay

Beep on Exit Delay

Alarm Transmission Delay

8.10

Silent Zones and Silent Panics Option

8.11

Bell Cut-Off Time

8.12

Code Priority

8.13

Closing Delinquency Timer

8.14

Restrict Arming on Battery Failure

8.15

Restrict Arming on Tamper Trouble

Part 9: PGMs (Programmable Outputs)

9.1

9.2

PGM Types

PGM Timer Setting

9.3

PGM Options

Part 10: Other Options

10.1

Telephone Line Monitoring (TLM)

10.2

Dialing Options

10.3

Dialing Pulse Rates

10.4

Keypad Panic Options

10.5

Panel Time

10.6