Danger zones. Krone BA EasyCut F 360 M gez.

Add to My manuals
136 Pages

advertisement

Danger zones. Krone BA EasyCut F 360 M gez. | Manualzz

2

2.4

Safety

Basic safety instructions

Technical limit values

If the technical limit values of the machine are not observed, the machine may be damaged. As a result, accidents may occur and people may be seriously or fatally injured. With regard to safety, it is especially important to observe the following technical limit values:

• maximum permitted operating pressure of the hydraulics

• maximum permitted drive speed

• maximum permitted axle loads of the tractor

• maximum permitted transport height and width

„

Comply with limit values, see Page 47 .

2.4.10

Danger zones

If the machine is switched on, its surrounding can present a danger zone.

Avoid entering the danger zone of the machine by observing the minimum safety distance.

If the safety distance is not observed, people may be seriously injured or killed.

„ Do not switch on the drives and engine if the minimum safety distance has not been observed.

„ If people fail to observe the minimum safety distance, switch off the drives.

„ Switch the machine off in shunting and field mode.

The safety distance is:

For machine in shunting and field mode

In front of the machine

Behind the machine

On either side of the machine

30 m

5 m

3 m

For machine switched on without driving motion

In front of the machine 3 m

Behind the machine 5 m

On either side of the machine 3 m

The safety distances specified here are minimum distances in terms of intended use. If necessary, these safety distances must be increased according to the operating and ambient conditions.

„ Before working in front of and behind the tractor and in the danger zone of the machine:

Shut down and secure the machine, see Page 24 . This also applies to brief inspection

work.

„ Consider the information in all relevant operating instructions:

• the operating instructions of the tractor

• the operating instructions of the machine

• the operating instructions of universal shaft

Danger zone universal shaft

People may be caught, pulled in and seriously injured by the universal shaft.

„ Observe operating instructions of universal shaft.

„ Ensure sufficient overlap of section tube and universal shaft guards.

„ Make sure that the universal shaft guards are mounted and that they are fully functional.

16

EasyCut F 360 M

Original operating instructions 150000792_04_en

Safety

Basic safety instructions

„ Allow the universal shaft locks to engage. There must be no areas of the locking device on the PTO shaft fork which could cause catching or entrapment (e.g. by annular design, protective collar around the locking pin).

„ Attach chains to prevent the universal shaft guards from rotating with the shaft.

„ Make sure that there is no one in the danger zone of PTO shaft and universal shaft.

„ Ensure that the selected speed and direction of rotation of the PTO shaft of the tractor match the permitted speed and direction of rotation of the machine.

„ Switch off the PTO shaft when the angles between the universal shaft and the PTO shaft are too large. The machine may be damaged. Parts may be hurled up and cause injury to people.

2

2.4

Danger zone PTO shaft

People may be caught, pulled in and seriously injured by the PTO shaft and the driven components.

Before switching on the PTO shaft:

„ Ensure that all protective devices are mounted and brought into protective position.

„ Make sure that there is no one in the danger zone of PTO shaft and universal shaft.

„ Switch off drives if they are not needed.

Danger zone between tractor and machine

People standing between the tractor and machine may be seriously injured or killed if the tractor rolls away or by carelessness or machine movements:

„ Before carrying out any work between the tractor and the machine: Always turn off and

secure the machine, see Page 24

. This also applies to brief inspection work.

„ If the lifting device must be actuated, instruct all people to keep away from the range of movement of the lifting device.

Danger zone ejected objects

Crops and foreign bodies may be forcefully flung out and injure or kill people.

„ Before starting the machine, instruct all people to leave the danger zone of the machine.

„ If people are in the danger zone of the machine, immediately switch off drives and diesel engine.

Danger zone when drive is switched on

When the drive is switched on, there is a danger to life caused by rotating machine parts.

Ensure that there are no persons in the danger zone of the machine.

„ Before starting the machine, instruct all people to leave the danger zone of the machine.

„ In case of dangerous situations, immediately switch off drives and instruct people to leave the danger zone.

Danger zone due to trailing machine parts

If machine parts are trailing, people may be seriously injured or killed.

EasyCut F 360 M

Original operating instructions 150000792_04_en 17

advertisement

Key Features

  • Hydraulic lift system for easy raising and lowering of the mower deck
  • Quick-release blade system for fast and easy blade changes
  • Built-in sharpener for keeping blades sharp
  • Highly maneuverable for use in tight spaces
  • Durable construction for long-lasting performance
  • Easy to use and maintain
  • Versatile machine for a wide range of mowing applications

Related manuals

Frequently Answers and Questions

What is the cutting width of the Krone BA EasyCut F 360 M gez?
The cutting width of the Krone BA EasyCut F 360 M gez. is 3.6 meters.
What is the maximum mowing speed of the Krone BA EasyCut F 360 M gez?
The maximum mowing speed of the Krone BA EasyCut F 360 M gez. is 15 km/h.
What is the weight of the Krone BA EasyCut F 360 M gez?
The weight of the Krone BA EasyCut F 360 M gez. is 750 kg.
What type of blades does the Krone BA EasyCut F 360 M gez. use?
The Krone BA EasyCut F 360 M gez. uses hardened steel blades.
How often should the blades on the Krone BA EasyCut F 360 M gez. be sharpened?
The blades on the Krone BA EasyCut F 360 M gez. should be sharpened every 20-25 hours of use.
What is the warranty on the Krone BA EasyCut F 360 M gez?
The Krone BA EasyCut F 360 M gez. comes with a 2-year warranty.

advertisement

Table of contents