Dangers in connection with certain activities: Working on the machine. Krone BA EasyCut F 360 M gez.

Add to My manuals
136 Pages

advertisement

Dangers in connection with certain activities: Working on the machine. Krone BA EasyCut F 360 M gez. | Manualzz

2

2.4

Safety

Basic safety instructions

Liquids under high pressure

The following liquids are under high pressure:

• Hydraulic oil

Liquids escaping under high pressure may penetrate through the skin and cause severe injuries.

„ Shut down and safeguard the machine and contact qualified specialist workshop upon suspicion of damaged hydraulic system.

„ Never search for leaks with bare hands. Even a very pin-sized hole may lead to serious injuries.

„ When searching for leaks, use suitable aids, e.g. a piece of cardboard to avoid injuries.

„ Keep body and face away from leaks.

„ If liquids penetrate the body, immediately consult a doctor. The liquid must be removed from the body as quickly as possible.

Hot liquids

Persons can suffer burns and/or scalding when hot liquids are drained.

„ Wear personal protective equipment when hot consumables are drained.

„ If necessary, allow liquids and machine parts to cool down before you start repair, maintenance and cleaning work.

Damaged hydraulic hoses

Damaged hydraulic hoses may tear off, burst or cause oil leaks. As a result, the machine may be damaged and people may be seriously injured.

„

Shut down and safeguard the machine, see Page 24

.

„ If it is suspected that hydraulic hoses are damaged, immediately contact a service centre,

see Page 109

.

2.4.19

Hot surfaces

The following components may become hot during operation and may burn people:

• Gearbox

• Cutterbar

„ Maintain an adequate distance from hot surfaces and adjacent components.

„ Leave machine parts to cool down and wear protective gloves.

Dangers in connection with certain activities: Working on the machine

Only perform work when the machine is at standstill

If the machine is not shut down and safeguarded, parts may move unintentionally or the machine may start moving. Thus there is a risk of serious injuries or death.

„ Before carrying out any repair, maintenance and cleaning work on the machine, shutdown and safeguard it,

see Page 24

.

22

EasyCut F 360 M

Original operating instructions 150000792_04_en

Safety

Basic safety instructions

Maintenance and repair work

Improper maintenance and repair work endanger operational safety. Thus there is a risk of accidents, serious injuries or death.

„ Only perform work which is described in this operating instructions. Prior to any work, stop

and safeguard the machine, see Page 24

.

„ All other maintenance and repair work must only be performed by qualified specialist workshop.

2

2.4

Working at or on heights of the machine

There is a risk of falling when working at or on heights of the machine. As a result, accidents may occur and people may be seriously or fatally injured.

„

Prior to any work, stop and safeguard the machine, see Page 24 .

„ Make sure you stand securely.

„ Use a suitable fall protection.

„ Secure the area below the assembly point against falling objects.

Raised machine and machine parts

The raised machine and machine parts may fall or tilt unintentionally. People may be seriously injured or killed, as a result.

„

Do not stay under the raised machine or machine parts which are not safely supported, see

Page 24 .

„ Prior to all work on raised machines or machine parts, lower the machine or machine parts.

„ Before performing any work under raised machines or machine parts, secure the machine or machine parts with rigid safety support or with hydraulic shut-off device or by supporting against lowering.

Danger associated with welding work

Improper welding work will endanger the operational safety of the machine. As a result, accidents may occur and people may be seriously or fatally injured.

„ Never perform welding work on the following components:

• Gearbox

• Components of the hydraulics

• Components of the electronics

• Frame or supporting components

• Running gear

„ Before carrying out welding work on the machine, obtain consent by KRONE customer service and, if required, identify alternatives.

„ Before performing welding work on the machine, park the machine safely and disconnect it from the tractor.

„ Welding work must only be performed by experienced qualified personnel.

„ Attach the earthing of the welding device near the welding points.

„ Caution when performing welding work near electric and hydraulic parts, plastic parts and pressure accumulators. The parts may be damaged, endanger people or cause accidents.

EasyCut F 360 M

Original operating instructions 150000792_04_en 23

advertisement

Key Features

  • Hydraulic lift system for easy raising and lowering of the mower deck
  • Quick-release blade system for fast and easy blade changes
  • Built-in sharpener for keeping blades sharp
  • Highly maneuverable for use in tight spaces
  • Durable construction for long-lasting performance
  • Easy to use and maintain
  • Versatile machine for a wide range of mowing applications

Related manuals

Frequently Answers and Questions

What is the cutting width of the Krone BA EasyCut F 360 M gez?
The cutting width of the Krone BA EasyCut F 360 M gez. is 3.6 meters.
What is the maximum mowing speed of the Krone BA EasyCut F 360 M gez?
The maximum mowing speed of the Krone BA EasyCut F 360 M gez. is 15 km/h.
What is the weight of the Krone BA EasyCut F 360 M gez?
The weight of the Krone BA EasyCut F 360 M gez. is 750 kg.
What type of blades does the Krone BA EasyCut F 360 M gez. use?
The Krone BA EasyCut F 360 M gez. uses hardened steel blades.
How often should the blades on the Krone BA EasyCut F 360 M gez. be sharpened?
The blades on the Krone BA EasyCut F 360 M gez. should be sharpened every 20-25 hours of use.
What is the warranty on the Krone BA EasyCut F 360 M gez?
The Krone BA EasyCut F 360 M gez. comes with a 2-year warranty.

advertisement

Table of contents