Carrying out oil level check and oil and filter element changes safely. Krone BA EasyCut F 360 M gez.

Add to My manuals
136 Pages

advertisement

Carrying out oil level check and oil and filter element changes safely. Krone BA EasyCut F 360 M gez. | Manualzz

2.5.3

2.6

Safety

Safety labels on the machine

In order to safely support the machine or machine parts:

„ To support, only use suitable and sufficiently dimensioned materials that do not break or yield.

„ Bricks and hollow blocks are not suitable for safely supporting the machine and machine parts. Therefore they must not be used.

„ Car jacks are also not suitable for safely supporting the machine and machine parts. They must not be used, as well.

2

2.6

Carrying out oil level check and oil and filter element changes safely

WARNING

Carrying out oil level check and oil and filter element changes safely

If oil level check and oil and filter element changes are not carried out safely, the operational safety of the machine may be impaired. This may result in accidents.

„ Carry out oil level check and oil and filter element changes safely.

To carry out oil level check, oil and filter element changes safely:

„ Lower raised machine parts or secure them against falling,

see Page 24 .

„

Shut down and safeguard the machine, see Page 24

.

„ Observe the intervals for oil level check, oil and filter element changes,

see Page 99 .

„ Use only the oil grades and quantities specified in the consumables table,

see Page 48

.

„ Clean the area around the parts (for example gearbox, high-pressure filter) and make sure that no foreign objects get into the parts or the hydraulic system.

„ Check existing seal rings for damage and replace them, if necessary.

„ Collect leaking or waste oil in a container designated for the purpose and dispose of it

properly, see Page 20 .

Safety labels on the machine

Every safety label is provided with an order number and can be ordered directly from the authorised KRONE dealer. Immediately replace missing, damaged and unrecognisable safety labels.

When attaching safety labels, the contact surface on the machine must be clean and free of dirt, oil and grease to ensure optimum adhesion of the labels.

EasyCut F 360 M

Original operating instructions 150000792_04_en 25

2

2.6

Safety

Safety labels on the machine

Position and meaning of safety labels

For the “pushed” version

KM000-748

27 021 592 0

5

6

7

1

1 2

3 4

1

1

7

26

EasyCut F 360 M

Original operating instructions 150000792_04_en

Safety

Safety labels on the machine

2

2.6

1.

Ord. no. 939 576 0 (4x)

2.

Ord. no. 939 106 3 (1x) a)

Danger due to rotating machine parts

When the machine has been switched off, there is risk of injury due to coasting machine parts.

„ Do not touch any moving parts of the machine.

„ Wait until the machine parts have come to a standstill.

b)

Danger from objects being flung out

When the machine is running, there is a risk of injury as objects may be flung out uncontrollably.

„ Before starting up, move the guards into their protective position.

c)

Danger from objects being flung out

When the machine is running, there is a risk of injury as objects may be flung out uncontrollably.

„ When the machine is running, keep your distance.

Danger to life when exceeding the maximum permitted

PTO speed

When exceeding the permissible PTO speed, machine parts may be destroyed or ejected.

As a result, people may be seriously or fatally injured.

„ Observe the permissible PTO speed.

3.

Ord. no. 939 101 4 (1x)

Danger when exceeding the maximum permissible PTO speed or the maximum permissible operating pressure

When exceeding the permissible PTO speed, machine parts may be destroyed or ejected.

If the maximum permissible operating pressure is exceeded, hydraulic parts may be damaged.

As a result, people may be seriously or fatally injured.

„ Observe the permissible PTO speed.

„ Observe the permitted operating pressure.

EasyCut F 360 M

Original operating instructions 150000792_04_en 27

2

2.6

Safety

Safety labels on the machine

4.

Ord. no. 27 002 459 0 (1x)

Danger due to machine parts unintentionally folding down or swivelling out

Risk of injury for road users due to machine parts unintentionally folding down or swivelling out.

„ Whenever transporting the machine or driving on roads, ensure that the stop cock is closed.

5.

Ord. no. 939 471 1 (1x)

Danger due to incorrect operation and lack of knowledge

Incorrect operation and lack of knowledge of the machine as well as incorrect behaviour in hazardous situations is risking the life of the operator and third parties.

„ Before starting up the machine, read and follow the operating instructions and safety instructions.

6.

Ord. no. 27 021 592 0 (1x)

Danger if the regulating valves of the tractor are not locked

There is a risk of accidents if the regulating valves of the tractor are not locked.

„ To prevent functions from being triggered accidentally, the regulating valves of the tractor must be in neutral position and locked during road transport journeys.

7.

Ord. no. 942 196 1 (2x)

Danger due to crushing or shearing

Risk of injury due to crushing or shearing points on moving machine parts.

„ While parts are moving, never reach into areas where there is a risk of being crushed.

28

EasyCut F 360 M

Original operating instructions 150000792_04_en

Safety

Safety labels on the machine

2

2.6

EasyCut F 360 M

Original operating instructions 150000792_04_en 29

2

2.6

Safety

Safety labels on the machine

For the “trailed” version

1

1

2

2

3

4

5

2

2

KM000-480

27 021 592 0

8

6

9 7

6

30

EasyCut F 360 M

Original operating instructions 150000792_04_en

Safety

Safety labels on the machine

2

2.6

1.

Ord. no. 942 459 0 (2x)

2.

Ord. no. 939 576 0 (4x)

3.

Ord. no. 939 106 3 (1x)

Danger due to crushing or shearing

Risk of injury due to crushing or shearing points on moving machine parts.

„ While parts are moving, never reach into areas where there is a risk of being crushed.

a)

Danger due to rotating machine parts

When the machine has been switched off, there is risk of injury due to coasting machine parts.

„ Do not touch any moving parts of the machine.

„ Wait until the machine parts have come to a standstill.

b)

Danger from objects being flung out

When the machine is running, there is a risk of injury as objects may be flung out uncontrollably.

„ Before starting up, move the guards into their protective position.

c)

Danger from objects being flung out

When the machine is running, there is a risk of injury as objects may be flung out uncontrollably.

„ When the machine is running, keep your distance.

Danger to life when exceeding the maximum permitted

PTO speed

When exceeding the permissible PTO speed, machine parts may be destroyed or ejected.

As a result, people may be seriously or fatally injured.

„ Observe the permissible PTO speed.

4.

Ord. no. 939 101 4 (1x)

EasyCut F 360 M

Original operating instructions 150000792_04_en

Danger when exceeding the maximum permissible PTO speed or the maximum permissible operating pressure

When exceeding the permissible PTO speed, machine parts may be destroyed or ejected.

If the maximum permissible operating pressure is exceeded, hydraulic parts may be damaged.

As a result, people may be seriously or fatally injured.

„ Observe the permissible PTO speed.

„ Observe the permitted operating pressure.

31

2

2.6

Safety

Safety labels on the machine

5.

Ord. no. 27 002 459 0 (1x)

Danger due to machine parts unintentionally folding down or swivelling out

Risk of injury for road users due to machine parts unintentionally folding down or swivelling out.

„ Whenever transporting the machine or driving on roads, ensure that the stop cock is closed.

6.

Ord. no. 942 196 1 (2x)

Danger due to crushing or shearing

Risk of injury due to crushing or shearing points on moving machine parts.

„ While parts are moving, never reach into areas where there is a risk of being crushed.

7.

Ord. no. 939 529 0 (2x)

8.

Ord. no. 939 471 1 (1x)

Danger due to high-pressure liquid

The pressure accumulator is under gas and oil pressure.

There is a risk of injury if the pressure accumulator is not removed or repaired properly.

„ Observe the notices in the operating instructions before removing and repairing the pressure accumulator.

„ The pressure accumulator may only be removed and repaired by a specialist workshop.

Danger due to incorrect operation and lack of knowledge

Incorrect operation and lack of knowledge of the machine as well as incorrect behaviour in hazardous situations is risking the life of the operator and third parties.

„ Before starting up the machine, read and follow the operating instructions and safety instructions.

32

EasyCut F 360 M

Original operating instructions 150000792_04_en

advertisement

Key Features

  • Hydraulic lift system for easy raising and lowering of the mower deck
  • Quick-release blade system for fast and easy blade changes
  • Built-in sharpener for keeping blades sharp
  • Highly maneuverable for use in tight spaces
  • Durable construction for long-lasting performance
  • Easy to use and maintain
  • Versatile machine for a wide range of mowing applications

Related manuals

Frequently Answers and Questions

What is the cutting width of the Krone BA EasyCut F 360 M gez?
The cutting width of the Krone BA EasyCut F 360 M gez. is 3.6 meters.
What is the maximum mowing speed of the Krone BA EasyCut F 360 M gez?
The maximum mowing speed of the Krone BA EasyCut F 360 M gez. is 15 km/h.
What is the weight of the Krone BA EasyCut F 360 M gez?
The weight of the Krone BA EasyCut F 360 M gez. is 750 kg.
What type of blades does the Krone BA EasyCut F 360 M gez. use?
The Krone BA EasyCut F 360 M gez. uses hardened steel blades.
How often should the blades on the Krone BA EasyCut F 360 M gez. be sharpened?
The blades on the Krone BA EasyCut F 360 M gez. should be sharpened every 20-25 hours of use.
What is the warranty on the Krone BA EasyCut F 360 M gez?
The Krone BA EasyCut F 360 M gez. comes with a 2-year warranty.

advertisement

Table of contents