Commissioning. Krone BA EasyCut F 360 M gez.

Add to My manuals
136 Pages

advertisement

Commissioning. Krone BA EasyCut F 360 M gez. | Manualzz

6

6.1

6

Commissioning

Checklist for initial operation

Commissioning

This chapter describes assembly and adjustment work on the machine which may be carried out by qualified technicians only. Here, the notice “Personnel qualification of technicians” applies,

see Page 14

.

WARNING

Risk of injury or damage to the machine due to faulty initial operation

If the initial operation is carried out incorrectly or incompletely, the machine may present defects. As a result, people may be injured or killed or the machine may be damaged.

„ Initial operation must only be carried out by authorised technicians.

„ Read in full and observe the “Personnel qualification of technicians”,

see Page 14 .

WARNING

Risk of injury due to non-observance of relevant safety notices

If the relevant safety notices are not observed, persons may get seriously injured or killed.

„

To avoid accidents, the basic safety instructions must be read and observed, see

Page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

see Page 24 .

6.1

Checklist for initial operation

ü The supplied operating instructions are in the document storage tube.

ü The machine is mounted according to assembly instructions of the machine.

ü All screws and nuts are checked for tightness, and are tightened to the specified tightening

torques, see Page 101 .

ü The safety devices are mounted and checked for completeness and damage.

ü The machine is fully lubricated,

see Page 122 .

ü

The oil level has been checked for all gearboxes, see Page 110 .

ü The hydraulic system has been checked for leaks.

ü The tractor corresponds to the machine requirements,

see Page 47 .

ü

The axle loads, the minimum counterweight and the total weight have been checked. see

Page 47 .

ü The length of the universal shaft has been checked and adjusted,

see Page 56 .

ü

The blades have been inserted, see Page 114 .

ü The hydraulic system has been vented.

ü The friction clutch has been vented,

see Page 104

.

ü The coupling points have been adapted,

see Page 52

.

ü The clearance between tractor and machine has been checked,

see Page 62

.

50

EasyCut F 360 M

Original operating instructions 150000792_04_en

advertisement

Key Features

  • Hydraulic lift system for easy raising and lowering of the mower deck
  • Quick-release blade system for fast and easy blade changes
  • Built-in sharpener for keeping blades sharp
  • Highly maneuverable for use in tight spaces
  • Durable construction for long-lasting performance
  • Easy to use and maintain
  • Versatile machine for a wide range of mowing applications

Related manuals

Frequently Answers and Questions

What is the cutting width of the Krone BA EasyCut F 360 M gez?
The cutting width of the Krone BA EasyCut F 360 M gez. is 3.6 meters.
What is the maximum mowing speed of the Krone BA EasyCut F 360 M gez?
The maximum mowing speed of the Krone BA EasyCut F 360 M gez. is 15 km/h.
What is the weight of the Krone BA EasyCut F 360 M gez?
The weight of the Krone BA EasyCut F 360 M gez. is 750 kg.
What type of blades does the Krone BA EasyCut F 360 M gez. use?
The Krone BA EasyCut F 360 M gez. uses hardened steel blades.
How often should the blades on the Krone BA EasyCut F 360 M gez. be sharpened?
The blades on the Krone BA EasyCut F 360 M gez. should be sharpened every 20-25 hours of use.
What is the warranty on the Krone BA EasyCut F 360 M gez?
The Krone BA EasyCut F 360 M gez. comes with a 2-year warranty.

advertisement

Table of contents