Start-up. Krone BA EasyCut F 360 M gez.

Add to My manuals
136 Pages

advertisement

Start-up. Krone BA EasyCut F 360 M gez. | Manualzz

7

7.1

Start-up

Calculating the ballasting of the tractor-machine combination

7

7.1

Start-up

WARNING

Risk of injury due to non-observance of relevant safety notices

If the relevant safety notices are not observed, persons may get seriously injured or killed.

„

To avoid accidents, the basic safety instructions must be read and observed, see

Page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

see Page 24 .

WARNING

Risk of injury or damage to the machine due to connection lines which have been incorrectly connected, interchanged or improperly installed

If the connection lines of the machine have been incorrectly connected to the tractor or have been improperly installed, they may pull off or be damaged. This may result in serious accidents. If connection lines are interchanged, functions may inadvertently be actuated which may also result in serious accidents.

„ Correctly connect and secure the hoses and cables.

„ Lay the hoses, cables and ropes so that they do not scrape, come under tension or become jammed or come into contact with other components (e.g. tractor tyres).

„ Couple and connect the hoses and cables to the designated connections as described in the operating instructions.

Calculating the ballasting of the tractor-machine combination

WARNING

Danger due to wrong weight distribution in the tractor-machine combination

Due to wrong weight distribution in the tractor-machine combination, people may be seriously or fatally injured.

„ Before starting up the tractor-machine combination, check the following requirements and, if required, adjust according to the operating instructions.

When attaching implements at the front and rear, the permitted total weight, the permitted axle loads and the tyre load capacity of the tractor must not be exceeded. These specifications can be found on the type plate, in the vehicle registration document or in the operating instructions for the tractor.

Even with an implement mounted at the rear, the front axle of the tractor must always be loaded with at least 20% of the tare weight of the tractor.

„ To ensure the suitability of the tractor, perform the following calculation before mounting the implement on the tractor:

EasyCut F 360 M

Original operating instructions 150000792_04_en 57

7

7.1

Start-up

Calculating the ballasting of the tractor-machine combination e

G

V a f

T

V

T

L b

T

H c d

G

H

Abbreviations for calculating the ballasting

TL [kg] Tare weight of the tractor See operating instructions for the tractor

TV [kg] Front axle load of the empty tractor See operating instructions for the tractor

TH [kg] Rear axle load of the empty tractor See operating instructions for the tractor

GH [kg] Total weight implement mounted at the rear/rear weight

GV [kg] Total weight of implement mounted at the front/front ballast

See price list and/or operating instructions for the machine

See price list and/or operating instructions for the machine a [m] Distance between centre of gravity of implement mounted at the front/ front ballast and middle of front axle b [m] Wheel base of the tractor

See price list and/or operating instructions for the machine

Measuring

See operating instructions for the tractor

Measuring c [m] Distance between middle of rear axle and middle of lower link ball

See operating instructions for the tractor

Measuring

See price list and/or operating instructions for the implement d [m] Distance between middle of lower link ball and centre of gravity of implement mounted at the rear/rear weight f e [m] Distance between middle of lower link ball and centre of gravity of implement mounted at the front

[m] Distance between front axle and middle of lower link ball

Calculation of the minimum ballasting at front G

V min for implements mounted at the rear and front and rear combinations

G

V min

=

G

H

( c

+

( e d )

+

− f

T

V

)

+

• b b

+

0 , 2

T

L

• b

„ Enter the calculated minimum ballasting, which is required at the front of the tractor, in the table.

58

EasyCut F 360 M

Original operating instructions 150000792_04_en

Start-up

Calculating the ballasting of the tractor-machine combination

Calculation of the minimum ballasting at rear G

H min for implements mounted at the front

7

7.1

G

H min

=

G

V

( e

+ f )

T

H b

+ c

+

• b

+ x d

T

L

• b

„ For "x" observe the technical data of the tractor manufacturer. If "x" is not indicated, insert the value 0.45.

„ Enter the calculated minimum ballasting, which is required at the rear of the tractor, in the table.

Calculation of the actual front axle load T

V tat

T

V tat

=

G

V

( e

+ f

+ b )

+

T

V

• b

G

H

( c

+ d ) b

„ Enter the actual front axle load and the permitted front axle load, indicated in the operating instructions for the tractor, in the table.

Calculation of the actual total weight G tat

G tat

=

G

V

+

T

L

+

G

H

„ If the required minimum ballasting at rear (G

H min

) is not reached with the implement mounted at the rear (G

H

), the weight of the implement mounted at the rear must be increased to the weight of the minimum ballasting at rear.

„ Enter the calculated, actual total weight and the permitted total weight, indicated in the operating instructions for the tractor, in the table.

Calculation of the actual rear axle load T

H tat

T

H tat

=

G tat

T

V tat

„ Enter the calculated, actual rear axle load and the permitted rear axle load, indicated in the operating instructions for the tractor, in the table.

Tyre load capacity

„ Enter double the value (two tyres) of the permitted tyre load capacity (see e.g. documents of the tyre manufacturers) in the table.

Table

The minimum ballasting must be attached to the tractor as a mounted implement or ballast weight. The calculated values must be less than/equal to (≤) the permitted values.

EasyCut F 360 M

Original operating instructions 150000792_04_en 59

advertisement

Key Features

  • Hydraulic lift system for easy raising and lowering of the mower deck
  • Quick-release blade system for fast and easy blade changes
  • Built-in sharpener for keeping blades sharp
  • Highly maneuverable for use in tight spaces
  • Durable construction for long-lasting performance
  • Easy to use and maintain
  • Versatile machine for a wide range of mowing applications

Related manuals

Frequently Answers and Questions

What is the cutting width of the Krone BA EasyCut F 360 M gez?
The cutting width of the Krone BA EasyCut F 360 M gez. is 3.6 meters.
What is the maximum mowing speed of the Krone BA EasyCut F 360 M gez?
The maximum mowing speed of the Krone BA EasyCut F 360 M gez. is 15 km/h.
What is the weight of the Krone BA EasyCut F 360 M gez?
The weight of the Krone BA EasyCut F 360 M gez. is 750 kg.
What type of blades does the Krone BA EasyCut F 360 M gez. use?
The Krone BA EasyCut F 360 M gez. uses hardened steel blades.
How often should the blades on the Krone BA EasyCut F 360 M gez. be sharpened?
The blades on the Krone BA EasyCut F 360 M gez. should be sharpened every 20-25 hours of use.
What is the warranty on the Krone BA EasyCut F 360 M gez?
The Krone BA EasyCut F 360 M gez. comes with a 2-year warranty.

advertisement

Table of contents