Mounting relief springs. Krone BA EasyCut F 360 M gez.

Add to My manuals
136 Pages

advertisement

Mounting relief springs. Krone BA EasyCut F 360 M gez. | Manualzz

7

7.7

Start-up

Mounting relief springs

7.7

KM000-254

Secure the top link on the A-frame or on the upper coupling point of the machine such that the raised machine is aligned as parallel as possible to the ground.

ü The machine is mounted on the tractor.

„ Raise the machine via the front hydraulics,

see Page 82 .

„

Shut down and safeguard the machine, see Page 24

.

„ Ensure that the machine is parallel to the ground.

Æ Continue connecting when the machine is raised and parallel to the ground.

Æ If parallelism deviates too much:

„ Lower the machine to the ground,

see Page 81 .

„

Shut down and safeguard the machine, see Page 24

.

„ Relocate the top link in the hole pattern on the A-frame.

„ Raise the machine via the front hydraulics,

see Page 82 .

„ Ensure that the machine is parallel to the ground.

„ Repeat this process until the machine is raised parallel to the ground.

Mounting relief springs

For the “pushed” version

64

KM000-356

With turnbuckle Without turnbuckle

The relief springs (1) can be attached to the top link fork (3) with or without turnbuckles (2).

If turnbuckles (I) are used, the turnbuckles (2) are attached between the supporting chains (4) of the relief springs and the top link fork (3).

If no turnbuckles (II) are used, the supporting chains (4) of the relief springs are attached directly to the top link fork (3).

EasyCut F 360 M

Original operating instructions 150000792_04_en

Start-up

Mounting relief springs

The ground pressure of the mower can be adjusted via the perforated bar, via the length of the supporting chain and, if using the turnbuckle, via the turnbuckle.

7

7.7

1

II

2

KMG100-004

„ Hook the relief springs (1) on the machine side into the second borehole (II) in the perforated bar (2).

Attaching the relief springs with a turnbuckle

KM000-357

„ Lift the machine into the transport position via the front hydraulics,

see Page 82

.

„

Shut down and safeguard the machine, see Page 24

.

„ Mount the turnbuckle (1) with the connecting link (2) on the top link fork (3).

„ Set the turnbuckle (1) to a maximum dimension X=230 mm .

„ Attach the chain (4) to the turnbuckle (1) using the connecting link (5). In doing so, hook in the chains as short as possible and the same on both sides.

„ Remove excess chain links or attach in a suitable position.

„ Lower the machine into the working position via the front hydraulics.

NOTICE

The relief springs are optimally adjusted when the inclination of the supporting chains is approximately 35° in the working position.

EasyCut F 360 M

Original operating instructions 150000792_04_en 65

7

7.7

Start-up

Mounting relief springs

Attaching the relief springs without a turnbuckle

„ Lift the machine into the transport position via the front hydraulics,

see Page 82

.

„

Shut down and safeguard the machine, see Page 24

.

„ Attach the chain (4) to the top link fork (2) using the connecting link (5). In doing so, hook in the chains as short as possible and the same on both sides.

„ Lower the machine into the working position via the front hydraulics.

NOTICE

The relief springs are optimally adjusted when the inclination of the supporting chains is approximately 35° in the working position.

Checking internal chains for overstretching

66

KM000-359

With turnbuckle (I) Without turnbuckle (II)

The relief springs (1) are prevented from overstretching by internal chains (2). To protect the relief springs from overstretching, the internal chains (2) must not tension in the working position.

Checking internal chains

„ Lower the machine into the working position via the front hydraulics.

„

Shut down and safeguard the machine, see Page 24

.

„ Visually check that the chains (2) do not tension.

ð If the chains (2) are sagging, everything is correct (III).

ð If the chains (2) are tensioned (IV), the chains (3) of the relief springs must be hooked into the next-longer chain link.

EasyCut F 360 M

Original operating instructions 150000792_04_en

advertisement

Key Features

  • Hydraulic lift system for easy raising and lowering of the mower deck
  • Quick-release blade system for fast and easy blade changes
  • Built-in sharpener for keeping blades sharp
  • Highly maneuverable for use in tight spaces
  • Durable construction for long-lasting performance
  • Easy to use and maintain
  • Versatile machine for a wide range of mowing applications

Related manuals

Frequently Answers and Questions

What is the cutting width of the Krone BA EasyCut F 360 M gez?
The cutting width of the Krone BA EasyCut F 360 M gez. is 3.6 meters.
What is the maximum mowing speed of the Krone BA EasyCut F 360 M gez?
The maximum mowing speed of the Krone BA EasyCut F 360 M gez. is 15 km/h.
What is the weight of the Krone BA EasyCut F 360 M gez?
The weight of the Krone BA EasyCut F 360 M gez. is 750 kg.
What type of blades does the Krone BA EasyCut F 360 M gez. use?
The Krone BA EasyCut F 360 M gez. uses hardened steel blades.
How often should the blades on the Krone BA EasyCut F 360 M gez. be sharpened?
The blades on the Krone BA EasyCut F 360 M gez. should be sharpened every 20-25 hours of use.
What is the warranty on the Krone BA EasyCut F 360 M gez?
The Krone BA EasyCut F 360 M gez. comes with a 2-year warranty.

advertisement

Table of contents