Setting the safety device. Krone BA EasyCut F 360 M gez.

Add to My manuals
136 Pages

advertisement

Setting the safety device. Krone BA EasyCut F 360 M gez. | Manualzz

10.5

Setting the safety device

1 1

Settings 10

Setting the safety device 10.5

1

6

2

4

3

5

10.6

KMG000-078

The protective equipment can be adapted to harvesting conditions by adjusting the guards. In order to avoid that crop stalks bend because the guards are too low, set the guards higher. To avoid that stones are slung away when the crops are low, set the guards lower.

ü

The machine is in the working position, see Page 81 .

ü

The machine is shut down and safeguarded, see Page 24

.

„ Remove the screw connections (3) and the sleeves (2) at both sides of the console (5).

„ Loosen the screw connections (4) at both sides of the console (5), do not remove them.

„ Use the oblong holes to bring the console (5) of the safety devices (1) into the desired position.

„ Mount the screw connections (3) with the sleeves (2) in the perforated bar (6).

„ Ensure that the screw connections (3) on either side of the console (4) are in the same position on the perforated bar (6).

„ Tighten the screw connection (4).

Configure/check the Camera Monitor System

The camera-monitor system must be set so that the road surface is visible up to the horizon, starting to the right resp. left side of the machine.

EasyCut F 360 M

Original operating instructions 150000792_04_en 97

10 Settings

10.6

Configure/check the Camera Monitor System

1

2 2 1

KMG100-003

ü

The camera-monitor system has been connected, see Page 70

.

„

Shut down and safeguard the machine, see Page 24

.

„ Switch on the ignition.

„ Switch the monitor on, see the monitor manufacturer's instructions.

„ Call up the divided display mode, see the monitor manufacturer's instructions.

„ Ensure that the cameras are properly connected to the monitor.

Æ The cameras are properly connected if the right-hand side of the divided display shows the picture from the right camera and the left-hand side that from the left camera.

Æ The cameras are not properly connected if the right-hand side of the divided display shows the picture from the left camera and the left-hand side that from the right camera. If the display sides are reversed, change the plugs (CAM1/CAM2),

see Page 70 .

„ Loosen the screws (2) and set the cameras (1) so that the visual field is visible in the monitor, starting at the side of the machine and reaching up to the horizon.

„ Tighten the screws (2).

98

EasyCut F 360 M

Original operating instructions 150000792_04_en

advertisement

Key Features

  • Hydraulic lift system for easy raising and lowering of the mower deck
  • Quick-release blade system for fast and easy blade changes
  • Built-in sharpener for keeping blades sharp
  • Highly maneuverable for use in tight spaces
  • Durable construction for long-lasting performance
  • Easy to use and maintain
  • Versatile machine for a wide range of mowing applications

Related manuals

Frequently Answers and Questions

What is the cutting width of the Krone BA EasyCut F 360 M gez?
The cutting width of the Krone BA EasyCut F 360 M gez. is 3.6 meters.
What is the maximum mowing speed of the Krone BA EasyCut F 360 M gez?
The maximum mowing speed of the Krone BA EasyCut F 360 M gez. is 15 km/h.
What is the weight of the Krone BA EasyCut F 360 M gez?
The weight of the Krone BA EasyCut F 360 M gez. is 750 kg.
What type of blades does the Krone BA EasyCut F 360 M gez. use?
The Krone BA EasyCut F 360 M gez. uses hardened steel blades.
How often should the blades on the Krone BA EasyCut F 360 M gez. be sharpened?
The blades on the Krone BA EasyCut F 360 M gez. should be sharpened every 20-25 hours of use.
What is the warranty on the Krone BA EasyCut F 360 M gez?
The Krone BA EasyCut F 360 M gez. comes with a 2-year warranty.

advertisement

Table of contents