Deviating tightening torques. Krone BA EasyCut F 360 M gez.

Add to My manuals
136 Pages

advertisement

Deviating tightening torques. Krone BA EasyCut F 360 M gez. | Manualzz

11 Maintenance - General Information

11.3

Deviating tightening torques

Thread

M10x1

M12x1.5

G1/4“

M14x1.5

M16x1.5

45

M18x1.5

50

M20x1.5

Locking screw and sight glass with copper ring 1

Bleed valve made of brass

Ventilation/breather filter made of steel

Steel and cast Aluminium

Ventilation/breather filter made of brass

Steel and cast

Maximum tightening torque (Nm) (±10%)

Aluminium

8

14

14

40

45

16

24

30

32

24

30

G1/2“

M22x1.5

M24x1.5

G3/4“

M33x2

G1“

M42x1.5

G1 1/4“

32

35

60

60

80

80

100

100

1  Always replace copper rings.

11.3

Deviating tightening torques

Screws/nuts

Nut for shear protection (rotary hub)

Bearing housing for cutting disc

Bearing housing for mower drum

Tightening torque

300 Nm

55 Nm

55 Nm

11.4

Venting the friction clutch

NOTICE

Interventions in the friction clutch will lead to a loss of guarantee!

Interventions in the friction clutch change the slip torque. Therefore the machine may be damaged considerably.

„ Never intervene in the overload protection.

„ Only use KRONE original spare parts.

Overloading and brief torque peaks limit the torque and transfer it evenly during slipping.

To guarantee the function, friction clutches must be bled before the initial start-up and after a prolonged standstill. To do this, the friction linings must be relieved and the clutch manually rotated.

104

EasyCut F 360 M

Original operating instructions 150000792_04_en

Maintenance - General Information 11

Venting the friction clutch 11.4

The friction clutch is designed with a permanently adjusted turning torque M

R

. The torque is applied to the housing of the friction clutch (2).

Bleeding friction clutch (Walterscheid series K92, K96, K97)

I

1 1

II

1

2

1 1

KM000-899

ü

The machine is in the working position, see Page 81 .

ü

The machine is shut down and safeguarded, see Page 24

.

„ Follow the operating instructions of the universal shaft manufacturer.

„ Remove the universal shaft.

„ Tighten the nuts (1) evenly (I), as a result of which the friction discs are relieved.

ð The friction discs are relieved.

„ Turn the friction clutch (2).

„ Then slacken the nuts (1) again as far as the thread run-out (II).

Bleeding friction clutch (Walterscheid series K90, K94, K92E)

3

1

4

2

KM000-900

ü

The machine is in the working position, see Page 81 .

ü

The machine is shut down and safeguarded, see Page 24

.

„ Follow the operating instructions of the universal shaft manufacturer.

„ Remove the universal shaft.

„ Measure dimension "L" on the compression spring (3) or on the setting screw (1).

„ Loosen the screws (1) or (4), as a result of which the friction discs are relieved.

ð The friction discs are relieved.

„ Turn the friction clutch (2).

„ Set the screws (1) or (4) again to the dimension "L".

EasyCut F 360 M

Original operating instructions 150000792_04_en 105

11 Maintenance - General Information

11.4

Venting the friction clutch

Bleeding the friction clutch (Walterscheid series K90/4T)

2

1

KM000-988

ü

The machine is in the working position, see Page 81 .

ü

The machine is shut down and safeguarded, see Page 24

.

„ Follow the operating instructions of the universal shaft manufacturer.

„ Remove the universal shaft.

„ Loosen the hexagon nuts (1) evenly but do not dismount them.

ð The friction discs are relieved.

„ Turn the friction clutch (2).

„ Tighten the hexagon nuts (1) evenly.

Venting friction clutch (ByPy)

106

KM000-603

ü

The machine is in the working position, see Page 81 .

ü

The machine is shut down and safeguarded, see Page 24

.

„ Follow the operating instructions of the universal shaft manufacturer.

„ Remove the universal shaft.

„ Loosen the cap nuts (1) uniformly but do not remove them.

ð The friction discs are relieved.

„ Turn the friction clutch (2).

„ Screw in the cap nuts (1) completely.

EasyCut F 360 M

Original operating instructions 150000792_04_en

advertisement

Key Features

  • Hydraulic lift system for easy raising and lowering of the mower deck
  • Quick-release blade system for fast and easy blade changes
  • Built-in sharpener for keeping blades sharp
  • Highly maneuverable for use in tight spaces
  • Durable construction for long-lasting performance
  • Easy to use and maintain
  • Versatile machine for a wide range of mowing applications

Related manuals

Frequently Answers and Questions

What is the cutting width of the Krone BA EasyCut F 360 M gez?
The cutting width of the Krone BA EasyCut F 360 M gez. is 3.6 meters.
What is the maximum mowing speed of the Krone BA EasyCut F 360 M gez?
The maximum mowing speed of the Krone BA EasyCut F 360 M gez. is 15 km/h.
What is the weight of the Krone BA EasyCut F 360 M gez?
The weight of the Krone BA EasyCut F 360 M gez. is 750 kg.
What type of blades does the Krone BA EasyCut F 360 M gez. use?
The Krone BA EasyCut F 360 M gez. uses hardened steel blades.
How often should the blades on the Krone BA EasyCut F 360 M gez. be sharpened?
The blades on the Krone BA EasyCut F 360 M gez. should be sharpened every 20-25 hours of use.
What is the warranty on the Krone BA EasyCut F 360 M gez?
The Krone BA EasyCut F 360 M gez. comes with a 2-year warranty.

advertisement

Table of contents