Repairs, maintenance and settings by technicians. Krone BA EasyCut F 360 M gez.

Add to My manuals
136 Pages

advertisement

Repairs, maintenance and settings by technicians. Krone BA EasyCut F 360 M gez. | Manualzz

17 Repairs, maintenance and settings by technicians

17.1

Replacing the shear bolt at the rotary hub

17 Repairs, maintenance and settings by technicians

This chapter describes repair, maintenance and adjustment work on the machine which may be performed by qualified technicians only. The chapter "Personnel qualification of the technicians"

must be read and observed in full, see Page 14

.

WARNING

Risk of injury due to non-observance of relevant safety notices

If the relevant safety notices are not observed, persons may get seriously injured or killed.

„

To avoid accidents, the basic safety instructions must be read and observed, see

Page 13 .

WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„ The safety routines must be read and observed to avoid accidents,

see Page 24 .

WARNING

Risk of injury or damage to the machine due to incorrect repair, maintenance and setting work.

Machines that are not repaired, maintained or set by technicians can exhibit faults caused by a lack of knowledge. As a result, people may be seriously injured or killed.

„ Only an authorised technician may carry out repair, maintenance and setting work at the machine.

„ Observe the qualification of technicians,

see Page 14

.

17.1

Replacing the shear bolt at the rotary hub

NOTICE

Wrong installation position

The machine may be damaged if the installation position of the bearing housings is not observed.

„ Clockwise rotating (RH) cutting discs / mower drums always have right-handed pinion shaft and nut (no groove mark on pinion shaft and nut).

„ Anti-clockwise rotating (LH) cutting discs / mower drums always have left-handed pinion shaft and nut (with groove mark on pinion shaft and nut).

124

EasyCut F 360 M

Original operating instructions 150000792_04_en

Repairs, maintenance and settings by technicians 17

Replacing the shear bolt at the rotary hub 17.1

KM000-049_1

ü

The machine is in the working position, see Page 81 .

ü

The machine is shut down and safeguarded, see Page 24

.

„ Dismount the cutting disc or the mower drum at the rotary hub with the defective shear bolt.

„ Remove the retaining ring (7).

„ Unscrew the screws (8).

„ Dismount the nut (2) by using the special key (10) included with delivery.

„ Dismount the hub (1).

„ Remove the damaged shear pins (3).

„ Check the nut and the hub for damage.

INFO : Replace damaged parts by KRONE original spare parts.

„ Fill the space above the bearing with grease (c).

„ Place the hub on the pinion shaft.

INFO : Observe the position of the shear pins. The slots of the shear pins (3) must be mounted facing each other horizontally , see detail (I).

„ Punch the new shear pins from the outside through the hub (1) and the shaft (4) until the end of the pin reaches the surface of the hub (d).

„ Using the special spanner (10), tighten the nut (2) with a tightening torque of 300 Nm .

„ Fit the screws (8) with detent edged washers.

„ Mount retaining ring (7).

„ Mount the cutting disc (5) or the mower drum (6).

EasyCut F 360 M

Original operating instructions 150000792_04_en 125

advertisement

Key Features

  • Hydraulic lift system for easy raising and lowering of the mower deck
  • Quick-release blade system for fast and easy blade changes
  • Built-in sharpener for keeping blades sharp
  • Highly maneuverable for use in tight spaces
  • Durable construction for long-lasting performance
  • Easy to use and maintain
  • Versatile machine for a wide range of mowing applications

Related manuals

Frequently Answers and Questions

What is the cutting width of the Krone BA EasyCut F 360 M gez?
The cutting width of the Krone BA EasyCut F 360 M gez. is 3.6 meters.
What is the maximum mowing speed of the Krone BA EasyCut F 360 M gez?
The maximum mowing speed of the Krone BA EasyCut F 360 M gez. is 15 km/h.
What is the weight of the Krone BA EasyCut F 360 M gez?
The weight of the Krone BA EasyCut F 360 M gez. is 750 kg.
What type of blades does the Krone BA EasyCut F 360 M gez. use?
The Krone BA EasyCut F 360 M gez. uses hardened steel blades.
How often should the blades on the Krone BA EasyCut F 360 M gez. be sharpened?
The blades on the Krone BA EasyCut F 360 M gez. should be sharpened every 20-25 hours of use.
What is the warranty on the Krone BA EasyCut F 360 M gez?
The Krone BA EasyCut F 360 M gez. comes with a 2-year warranty.

advertisement

Table of contents