Mounting and Adjusting the Relief Springs. Krone EasyCut F 360 CV, EasyCut F 360 CR, EasyCut F 320 CV

Add to My manuals
122 Pages

advertisement

Mounting and Adjusting the Relief Springs. Krone EasyCut F 360 CV, EasyCut F 360 CR, EasyCut F 320 CV | Manualzz

Start-up

Pos: 67.13 /Ü berschriften/Ü berschriften 2/A-E/AAnbau und Ei nstellung der Entlastungsfedern ÜS @ 89\mod_1321958243040_78.docx @ 756797 @ 2 @ 1

7.3

Pos: 67.14 /Ü berschriften/Ü berschriften 3/F-J/GGeschobene Ausführung @ 245\mod_1395916281296_78.docx @ 1914218 @ 3 @ 1

Mounting and Adjusting the Relief Springs

7.3.1 Pushed Design

Pos: 67.15 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Einstell ung der Entl astungsfeder n EC F 360 geschoben Bil d @ 245\mod_1395912760848_78.docx @ 1913825 @ @ 1

1

III

2

EC-516-0

Fig. 22

Pos: 67.16 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Di e Entlastungsfedern mä hwer kseitig einhängen EC F 360 CV Text @ 248\mod_1396512479701_78.docx @ 1929305 @ @ 1

• Hinge relief springs (1) on mowing unit side into the third hole (III) of the perforated bar (2).

Pos: 67.17 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Anbau und Ei nstellung der Entlastungsfedern EC F 360 g eschoben Bild @ 245\mod_1395909859855_78.docx @ 1913618 @ @ 1

2

2

1

3

3

EC-487-0

Fig. 23 with tension jack

Pos: 67.18 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Einführungstext mi t/ohne Spannschloss EC F 360 @ 248 \mod_1396514148084_78.docx @ 1929909 @ @ 1 without tension jack

The relief springs can be hinged with tension jack (1) or without tension jack on the clevis of the top link (2).

A finer adjustment of the ground pressure is possible if the tension jack is used.

A coarser adjustment of the ground pressure is possible if the tension jack is not used.

Pos: 67.19 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

56

Pos: 67.20 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Anbau mit Spanschl oss EC F 360 geschoben Bild @ 250 \mod_1396948815816_78.docx @ 1936768 @ @ 1

Start-up

5

2

4

1

3

EC-513-0

Fig. 24

Pos: 67.21 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Anbau mit Spannschl oss EC F 360 geschoben T ext @ 244\mod_1395763346385_78.docx @ 1908838 @ @ 1

Fitting with tension jack

• Mount tension jack (1) with connecting link (3) on the clevis of top link (2).

• Hinge relief springs on both sides with the same length.

• Set the tension jack to a maximum value of a = 230 mm.

• Raise mowing unit, switch off tractor engine, remove the ignition key and carry it with you.

• Fasten the chain (4) as short as possible with connecting link (5) on the tension jack (1).

• Lower mowing unit into mowing position.

Pos: 67.22 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Ü berschüssige Kette abtrennen EC F 360 CV Text @ 245\mod_1395912585351_78.docx @ 1913766 @ @ 1

• Separate surplus chain and fasten it at a suitable point.

Pos: 67.23 /BA/Inbetri ebnahme/EasyCut/Hinweis Entlastungsfeder n einstell en 35° @ 245 \mod_1395914748947_78.docx @ 1914099 @ @ 1

Note

In mowing position, the inclination of the relief spring chain should be approx. 35° in mowing position.

Pos: 67.24 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Anbau ohne Spanschloss EC F 360 geschoben Bil d @ 250\mod_1396949119980_78.docx @ 1936797 @ @ 1

2

4

3

EC-514-0

Fig. 25

Pos: 67.25 /BA/Erstinbetriebnahme/EasyC ut/F 360 C V/CR/Anbau ohne Spannschloss EC F 360 geschoben T ext @ 248 \mod_1396514300230_78.docx @ 1929938 @ @ 1

Fitting without tension jack

• Raise mowing unit, switch off tractor engine, remove the ignition key and carry it with you.

• Fasten the chain (4) as short as possible with connecting link (3) on the tension jack clevis

(2).

• Lower mowing unit into mowing position.

Pos: 67.26 /BA/Inbetri ebnahme/EasyCut/Hinweis Entlastungsfeder n einstell en 35° @ 245 \mod_1395914748947_78.docx @ 1914099 @ @ 1

Pos: 67.27 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Note

In mowing position, the inclination of the relief spring chain should be approx. 35° in mowing position.

57

advertisement

Related manuals

advertisement

Table of contents