Replacing Pulley. Krone EasyCut F 360 CV, EasyCut F 360 CR, EasyCut F 320 CV

Add to My manuals
122 Pages

advertisement

Replacing Pulley. Krone EasyCut F 360 CV, EasyCut F 360 CR, EasyCut F 320 CV | Manualzz

Pos: 75.33 /Ü berschriften/Ü berschriften 3/P-T/RRiemenschei be tauschen @ 328\mod_1426689351744_78.docx @ 2515676 @ 2 @ 1

Settings

10.4.2 Replacing Pulley

Pos: 75.34 /BA/Sicherheit/7. Gefahr enhinweise alt/Einstell arbeiten / Einstell ungen/Gefahr - Einstell ung en an der Maschi ne @ 0\mod_1196668628056_78.docx @ 10285 @ @ 1

Danger! - Settings on the machine

Effect: Danger to life, injuries or damage to the machine.

• Setting tasks must only be performed when the drive is switched off and the engine is at a standstill! Remove the ignition key!

Pos: 75.35 /BA/Ei nstellungen/M ähwer ke/Z etterdr ehzahl/M ontag e der Keilriemenschei ben EC F 360 CV/CR Bild @ 248\mod_1396527267816_78.docx @ 1930547 @ @ 1

1

3 5

4

6

2

7

3

8

4

EC-519-0

Fig. 46

Pos: 75.36 /BA/Ei nstellungen/M ähwer ke/Z etterdr ehzahl/M ontag e der Keilriemenschei ben EC F 360 CV/CR T ext @ 245\mod_1396009090393_78.docx @ 1916768 @ @ 1

• Push pulleys (1) onto the shaft top and bottom.

Make certain the pulleys are flush with each other.

• Secure pulley with disc (3) and linch pin (4).

• Pull V-belts (5) onto the V-belt pulleys.

• To tension the belt drive, insert blade key (6) into the tensioning device (7) and push it to the front until it engages.

Pos: 75.37 /Ü berschriften/Ü berschriften 3/P-T/RRiemenantri eb spannen @ 328\mod_1426686085413_78.docx @ 2514945 @ 3 @ 1

• Secure tensioning device with linch pin (8).

10.4.3 Tensioning Belt Drive

Pos: 75.38 /BA/Ei nstellungen/M ähwer ke/Z etterdr ehzahl/Ri ementrieb spannen EC F 360 C V/CR Bild @ 248 \mod_1396531120669_78.docx @ 1930925 @ @ 1

4

8

5

2

3

1

6

7

EC-521-0

Fig. 47

Pos: 75.39 /BA/Ei nstellungen/M ähwer ke/Z etterdr ehzahl/Spannen des Riementiebes EC F 360 C V/CR T ext @ 248\mod_1396531113982_78.docx @ 1930716 @ @ 1

When tensioning the V-belts, make certain that the adjustment aid (1) is flush with the upper edge of the tension spring (2).

• Loosen nuts (3) if the adjustment aid is not flush.

• Tension with threaded rod (4), tension spring (2) and lock with nuts (3) so that the adjustment aid is flush with the upper edge of the spring.

• Mount V-belt guard (8).

Pos: 75.40 /Layout Module /---------------Seitenumbr uch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

79

advertisement

Related manuals

advertisement

Table of contents