Preparing the wine conditioning unit. Miele 11329860, KWT 6722 iS

Add to My manuals
92 Pages

advertisement

Preparing the wine conditioning unit. Miele 11329860, KWT 6722 iS | Manualzz

*INSTALLATION*

Installation

All fitting instructions given are for a right-hand hinged appliance. If you have converted the appliance to lefthand hinging, you will need to adapt these instructions accordingly.

Preparing the wine conditioning unit

 Unscrew the transport safety devices   from both sides on the back of the wine conditioning unit and remove them upwards.

 Feed the power cord through to the electrical socket.

 Risk of fire due to short circuit.

When pushing the wine conditioning unit into its niche, make sure that the power cord does not get trapped.

Never operate a wine conditioning unit with a faulty power cord.

73

*INSTALLATION*

Installation

 Slide the filler panel   supplied from the front into the holders on the wine conditioning unit as shown.

 Push the wine conditioning unit two thirds of the way into the building-in niche.

 If the wine conditioning unit is lefthinged, allow for the position of the lug (see illustration above).

 Turn the front adjustable feet all the way in using the wrench   supplied.

 If the wine conditioning unit is righthinged, allow for the position of the lug (see illustration above).

74

*INSTALLATION*

Installation

 Unscrew the transport safety device   from the front of the wine conditioning unit, if you have not already done so.

Tip: Keep this device in a safe place for refitting should the appliance need to be moved in the future.

With 5/8" (16 mm) thick housing unit walls only:

 Remove the top cover   .

5

6

 Clip the spacers   and   supplied on the right-hand side of the hinges.

 Open the appliance door.

 Screw the supplied fixing bracket   loosely with the screws   supplied into the top left of the wine conditioning unit (1st and 3rd hole from the left). Do not tighten the screws so that you can adjust the position of the bracket   later on.

75

*INSTALLATION*

Installation

 Fit the stopper   supplied onto the fixing bracket   also supplied.

 Screw the supplied fixing bracket   loosely with the screws   supplied into the bottom of the appliance. Do not tighten the screws   so that you can adjust the position of this part.

 Push the wine conditioning unit two thirds of the way into the building-in niche.

 Carefully remove the protective foil from the supplied sealing strip   .

 Stick the sealing strip   onto the side of the appliance on which the door will open, flush with the front.

1. Position the sealing strip   flush with the lower edge of the top fixing bracket.

2. Stick it down along its entire length.

 If necessary, insert the locking pins supplied for limiting the door opening into the hinges from above (see “Adjusting the hinges”).

76

*INSTALLATION*

Installation

Installing the wine conditioning unit

If the wine conditioning unit is pushed too far into the building-in niche, the appliance door will not close properly. This can cause ice to build up and condensate to accumulate, and cause the appliance to malfunction. These issues can all lead to increased energy consumption.

Push the wine conditioning unit into the niche, making sure a gap of

1 5/8" (42 mm) is maintained all round between the appliance and the front of the housing unit side walls.

 Push the wine conditioning unit into the niche until the fixing brackets at the top and bottom touch the front edge of the housing unit side wall.

– With 5/8" (16 mm) thick housing unit walls:

The spacers should touch the front edge of the housing unit side wall at the top and bottom.

– With 3/4" (19 mm) thick housing unit walls:

The front edges of the top and bottom hinges should be flush with the front edge of the housing unit side wall.

 Check again that securing brackets at the top and bottom are flush with the front edge of the housing unit side wall.

This ensures a distance of

1 5/8" (42 mm) to the front edges of the housing unit side walls all the way round.

 Close the appliance door and align the wine conditioning unit with adjacent cabinetry.

 Align the height of the wine conditioning unit as necessary on both sides with the adjacent cabinetry by altering the adjustable feet using the wrench supplied.

77

*INSTALLATION*

Installation

1.

 Push the fixing brackets   and   against the housing unit wall.

4.

2.

 Push the hinged side of the appliance to the housing unit wall.

 To secure the wine conditioning unit to the housing unit, screw the supplied particle board screws   through the hinge plates at the top and bottom (1. + 2.).

3 .

 Now secure the wine conditioning unit to the other side of the housing unit by screwing the supplied particle

78

*INSTALLATION*

Installation board screws   and   through the hinge plates at the top and bottom (3.

+ 4.).

For additional stability of the wine conditioning unit in the housing unit, push the stabilizing rods supplied in underneath the appliance between it and the floor of the housing unit:

 Now tighten screws   and   .

1 8

1 8

17

 Snap off any protruding ends from securing brackets   and   . They are no longer required and can be disposed of in the household garbage.

17

 Then secure the handle   to one of the stabilizing rods   .

1 8

16

 Fit the cover   to the top fixing bracket.

 Fit the cover   supplied to the bottom fixing bracket.

 Use the handle to push the stabilizing rod   into the guide as far as it will go. Remove the handle   and fit it to the other stabilizing rod supplied and push this into its guide as far as it will go.

Tip: Important! Keep the handle   somewhere safe in case you ever need to fit the wine conditioning unit into new cabinetry.

79

*INSTALLATION*

Installation

 Check that the wine conditioning unit is standing securely in the building-in niche and that the appliance door closes properly.

Installing the custom door panel

If installed in a run of units, make sure that the top edge of the custom door panel is at the same height as adjoining unit doors.

The door panel must be installed level, and not under tension.

Please use the screws for the custom door panel as well as the gap cover included in the accessories supplied.

 Open the appliance door.

 Measure the distance X between the top edge of the housing unit wall above and the middle of the vertical slots in the mounting frame.

 Place the custom door panel on a firm surface, with the external side facing downwards (place on a blanket or similar to avoid it becoming scratched).

X

Y

 Remove the covers   from the top and bottom of the appliance door.

 Mark the distance X on the inner side of the custom door panel.

 Similarly, locate and mark the vertical midpoint Y on the custom door panel.

80

*INSTALLATION*

Installation

 Unscrew the nuts   and remove the mounting frame   from the appliance door.

X

Y

 Open the appliance door and hang the custom door panel from its mounting frame   onto the threaded bolts   from above.

 Position the mounting frame   on the custom door panel according to the markings and screw it tightly using the two screws   supplied.

81

*INSTALLATION*

Installation

 Screw the nuts   loosely onto the threaded bolts   . Do not tighten the nuts yet.

 Close the appliance door carefully and check the distance between the door and adjoining unit doors. The distance should be the same.

 Align the sides of the appliance door

X and the height Y using the threaded bolts.

82

*INSTALLATION*

 Close the appliance door again and check the distance between the door and adjoining unit doors.

 Now screw on the top nuts   . The appliance door is now secured.

Installation

 Secure the custom door panel to the appliance door at the bottom using the screws   supplied.

 Resecure the custom door panel at the top using the screws   supplied.

 Carefully move the seal   on the appliance door to one side and secure the custom door panel to the appliance door at 3 points on both sides using the screws   supplied.

83

*INSTALLATION*

Installation

 Replace the covers   at the top and bottom on the appliance door.

The following confirms that the appliance is correctly installed:

– The appliance door closes properly.

– The door does not touch the cabinet.

– The seal on the top corner of the handle side is firmly seated.

 To double check place a torch in the appliance and close the door.

Turn the lights out in the room. If you can see any light shining out from the sides double check the installation.

 Insert the gap cover   supplied into the gap between the custom door panel and the appliance door.

84

advertisement

Key Features

  • Built-in Compressor wine cooler 80 bottle(s) Number of temperature zones: 2 Black
  • Number of shelves: 8 Number of doors: 1
  • Wine cooler net capacity: 254 L
  • 32 dB
  • 176 kWh
  • Interior light Temperature alarm

Related manuals

Download PDF

advertisement

Table of contents