Locking / releasing stop cocks. Krone BA EasyCut B 970

Add to My manuals
110 Pages

advertisement

Locking / releasing stop cocks. Krone BA EasyCut B 970 | Manualzz

8

8.4

Operation

Locking / releasing stop cocks

WARNING! Crush hazard due to the support jack! Keep hands and feet out of the danger zone of the support jack.

„ Pull the bolts (1), push the front support jack (2) downwards and lock it using the bolts (1).

„ Pull the tension bar (4), swivel the rear support jack (3) downwards and lock it using the tension bar (4).

8.4

Locking / releasing stop cocks

8.5

KMG000-089

Locking

„ Move the stop cocks (1) into position (I).

Releasing

„ Move the stop cocks (1) into position (II).

Lifting/lowering the machine

WARNING

Danger to life, injuries or damage to the machine due to uncontrolled lowering of the machine

When lowering the machine into the working position, people or animals in the swivel range may be seriously injured and the machine may be damaged.

„ Lower the machine only when you are absolutely sure that there are no persons, animals or objects in the swivel range of the machine.

„ Only switch on the PTO shaft when the machine is in the working position.

62

KMG000-045

EasyCut B 970

Original operating instructions 150000711_04_us

Operation

Lifting/lowering the machine

8

8.5

From transport position to headland position

„ Move the toggle switch (2) to the “ up ” position.

„ Actuate the control unit (2-) until both mowers are lowered to the headland position.

Headland positions

ü The mowers are in the headland position.

„ Move the toggle switch (2) to “ down ” position.

Lowering both mowers simultaneously from the headland position to the working position

„ Move the toggle switch (3) to the “ centre ” position.

„ Move the control unit (1+) to the float position until both mowers are lowered to the working position.

„ To mow, move the control unit (1+) to the float position.

Raising both mowers simultaneously from the working position to the headland position

„ Move the toggle switch (3) to the “ centre ” position.

„ Actuate the control unit (1+) until both mowers are raised to the headland position.

Moving right mower from the headland position to the working position

„ Move the toggle switch (3) to the “ left ” position.

„ Actuate the control unit (2-) until the right mower is lowered to the working position.

„ To mow, move the control unit (2-) to the float position.

Moving right mower from the working position to the headland position

„ Move the toggle switch (3) to the “ left ” position.

„ Actuate the control unit (2+) until the right mower is raised to the headland position.

Moving left mower from the headland position to the working position

„ Move the toggle switch (3) to the “ left ” position.

„ Move the control unit (1+) to the float position until the left mower is lowered to the working position.

„ To mow, move the control unit (1+) to the float position.

Moving left mower from the working position to the headland position

„ Move the toggle switch (3) to the “ left ” position.

„ Actuate the control unit (1+) until the left mower is raised to the headland position.

From headland to transport position

ü The PTO drive is switched off.

ü The support jacks have been swivelled into the transport position and locked with the bolts.

„

Move machine to headland position, see Page 63

.

„ Move the toggle switch (2) into " top " position and hold.

„ Actuate the double-action control unit (2+) until the mowers are raised from the headland position to the transport position.

NOTE!

To prevent damaging the machine due to an operating error, switch off the operation panel.

„ To switch off the operation panel, move the toggle switch (2) into the " middle " position.

EasyCut B 970

Original operating instructions 150000711_04_us 63

advertisement

Related manuals

advertisement

Table of contents