- Computers & electronics
- Computer components
- System components
- Motherboards
- IEI Integration
- POC-W24C-ULT3
- User manual
3 INSTALLATION. IEI Technology POC-W24C-ULT3 160 Pages
3 INSTALLATION. IEI Technology POC-W24C-ULT3
advertisement
POC-W24C-ULT3 FHD Medical Panel PC
Chapter
3
3
Installation
Page 19
3.1 Anti-static Precautions
POC-W24C-ULT3 FHD Medical Panel PC
WARNING:
Failure to take ESD precautions during the maintenance of the
POC-W24C-ULT3 may result in permanent damage to the
POC-W24C-ULT3 and severe injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components, including the POC-W24C-ULT3. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the POC-W24C-ULT3 is accessed internally, or any other electrical component is handled, the following anti-static precautions are strictly adhered to.
Wear an anti-static wristband : Wearing a simple anti-static wristband can help to prevent ESD from damaging the board.
Self-grounding : Before handling the board, touch any grounded conducting material. During the time the board is handled, frequently touch any conducting materials that are connected to the ground.
Use an anti-static pad : When configuring the POC-W24C-ULT3, place it on an anti-static pad. This reduces the possibility of ESD damaging the
POC-W24C-ULT3.
Only handle the edges of the PCB : When handling the PCB, hold the PCB by the edges.
3.2 Installation Precautions
When installing the medical panel PC, please follow the precautions listed below:
Manufacturer authorization : Do not modify this equipment without authorization of manufacturer.
Certified Engineers : Only certified engineers should install and modify the hardware settings.
Power turned off : When installing the medical panel PC, make sure the power is off. Failing to turn off the power may cause severe injury to the body and/or damage to the system.
Page 20
POC-W24C-ULT3 FHD Medical Panel PC
Anti-static Discharge : If a user open the rear panel of the medical panel PC, to configure the jumpers or plug in added peripheral devices, ground themselves first and wear an anti-static wristband.
3.3 Installation and Configuration Steps
The following installation steps must be followed.
Step 1: Unpack the medical panel PC.
Step 2: Install an HDD.
Step 3: Install necessary accessories (handset, handle or combo reader).
Step 4: Configure the system.
Step 5: Connect peripheral devices to the medical panel PC.
Step 6: Mount the medical panel PC.
Step 0:
3.4 HDD Installation
To install the HDD into the system, please follow the steps below:
Step 1: Remove the twelve retention screws from the back cover (
).
Figure 3-1: Back Cover Retention Screws
Page 21
POC-W24C-ULT3 FHD Medical Panel PC
Step 2: Remove the back cover.
Step 3: Remove the six HDD bracket retention screws (
) and lift the HDD bracket off the panel PC.
Figure 3-2: HDD Bracket Retention Screws
Step 4: Place the HDD into the HDD bracket, aligning the four retention screw holes in the both sides of the HDD bracket with the retention screw holes on the sides of
Step 5: Insert four retention screws (M3*5) into the bracket (
).
Page 22
POC-W24C-ULT3 FHD Medical Panel PC
Figure 3-3: HDD Installation
Step 6: Connect the SATA cable from the POC-W24C-ULT3 to the rear of the HDD
(
).
Step 7: Replace the HDD bracket by securing the six retention screws previously
Step 8: Replace the back cover. Step 0:
3.5 Handset Installation (Optional)
An optional phone handset can be installed on the side of the POC-W24C-ULT3 to make
VoIP calls. To install the handset and the holder, please follow the instruction below.
Step 1: Locate the two retention screw holes for installing the handset holder on the rear
Page 23
POC-W24C-ULT3 FHD Medical Panel PC
Step 2: Secure the handset holder with the POC-W24C-ULT3 by two retention screws
(M3*8, flat head).
Figure 3-4: Handset Holder Retention Screws
Step 3: Plug the handset cord into a USB connector on the bottom panel.
Step 4: Place the handset in the holder.
Figure 3-5: Handset Installation
Page 24
advertisement
Related manuals
advertisement
Table of contents
- 16 1 INTRODUCTION
- 20 1.4.1 Backlit Touch Buttons
- 28 2 UNPACKING
- 34 3 INSTALLATION
- 40 3.5.1 Using VoIP Handset
- 44 3.6.1 Barcode Reader Installation
- 46 3.6.2 Reading Light
- 52 3.10.1 AT Power Mode
- 52 3.10.2 ATX Power Mode
- 53 3.11.1 Wall Mounting
- 56 3.11.2 Arm Mounting
- 58 3.11.3 Stand Mounting
- 60 4 BIOS SETUP
- 61 4.1.1 Starting Setup
- 61 4.1.2 Using Setup
- 62 4.1.3 Getting Help
- 62 4.1.4 BIOS Menu Bar
- 65 4.3.1 Trusted Computing
- 66 4.3.2 ACPI Settings
- 67 4.3.3 F81866 Super IO Configuration
- 70 4.3.4 F81866 H/W Monitor
- 71 4.3.5 RTC Wake Settings
- 72 4.3.6 Serial Port Console Redirection
- 76 4.3.7 CPU Configuration
- 78 4.3.8 SATA Configuration
- 80 4.3.9 USB Configuration
- 81 4.3.10 IEI Feature
- 82 4.4.1 System Agent (SA) Configuration
- 86 4.4.2 PCH-IO Configuration
- 94 5 DRIVER INSTALLATION
- 107 5.11.1 SCR Driver
- 111 5.11.2 MSR Driver
- 114 5.11.3 Fingerprint Reader Driver
- 118 6 SYSTEM MAINTENANCE
- 125 7 INTERFACE CONNECTORS
- 128 7.2.1 Audio Connector (AUDIO_OUT1)
- 128 7.2.2 Audio Out Connector (AMP_OUT1)
- 128 7.2.3 Battery Connector (BAT1)
- 129 7.2.4 Debug Connector (DBG_PORT1)
- 129 7.2.5 Inverter Connector (INVERTER1)
- 129 7.2.6 LVDS Connector (LVDS1)
- 130 7.2.7 MCU Connector (HOTKEY_CN1)
- 131 7.2.8 MCU Flash Connector (JP8)
- 131 7.2.9 MCU Flash SPI ROM Connector (MCU_SPI1)
- 131 7.2.10 Microphone Connector (DMIC1)
- 132 7.2.11 Power Button Connector (PWR_BTN1)
- 132 7.2.12 Power LED Connector (PW_LED1)
- 132 7.2.13 RS-232 Serial Port Connector (COM2)
- 133 7.2.14 SATA Connectors (SATA1 & SATA2)
- 133 7.2.15 SPI Flash Connector (JSPI1)
- 133 7.2.16 TPM Connector (TPM1)
- 134 7.2.17 USB Connector (BT_USB1)
- 134 7.2.18 USB Connector (CAM_USB1)
- 135 7.2.19 USB Connector (RFID_USB1)
- 135 7.2.20 USB Connector (TOUCH_USB1)
- 136 7.3.1 GbE Connectors (LAN1 & LAN2)
- 136 7.3.2 HDMI Output Connector (HDMI_OUT1)
- 137 7.3.3 Power Connector (PWR1)
- 137 7.3.4 RS-232/422/485 DB-9 Serial Port (COM1)
- 137 7.3.5 USB 2.0 Connectors (USB20_CN1)
- 138 7.3.6 USB 3.0 Connectors (USB_CON1)
- 138 7.3.7 USB 3.0 Connectors (USB_CON2)
- 139 7.4.1 Flash Descriptor Security Override Jumper (ME_FLASH1)
- 139 7.4.2 LVDS Panel Voltage Selection Jumper (J_VLVDS1)
- 140 7.4.3 LVDS Panel Resolution Selection Jumper (SW1)
- 140 7.4.4 PCIe Mini/mSATA Mode Selection (MSATA_CN1)
- 141 A REGULATORY COMPLIANCE
- 146 B SAFETY PRECAUTIONS
- 147 B.1.1 General Safety Precautions
- 148 B.1.2 Anti-static Precautions
- 149 B.1.3 Product Disposal
- 150 B.1.4 Classification
- 151 B.2.1 Maintenance and Cleaning
- 151 B.2.2 Cleaning Tools
- 152 C BIOS MENU OPTIONS
- 155 D WATCHDOG TIMER
- 158 E HAZARDOUS MATERIALS DISCLOSURE