3.6.2 Reading Light. IEI Technology POC-W24C-ULT3

POC-W24C-ULT3 FHD Medical Panel PC

Step 6: After driver installation is complete, push the barcode reader button to trigger the barcode reader.

Figure 3-13: Barcode Reader Button

WARNING:

Do not stare into beam of the laser light. The human eye can be damaged. Avoid that the laser beam hits reflective surfaces such as mirrors, etc. Any changes at the device are forbidden these could cause a dangerous laser light.

3.6.2 Reading Light

The barcode reader is also equipped with a reading light with 3-level of brightness. Push the reading light button to turn on or to toggle illumination brightness levels.

Figure 3-14: Reading Light

Page 31

POC-W24C-ULT3 FHD Medical Panel PC

3.7 3-in-1 Combo Reader Installation (Optional)

The 3-in-1 combo reader is an optional item for the POC-W24C-ULT3. The combo reader combines fingerprint reader, smart card reader (SCR) and magnetic stripe reader (MSR) into one compact device.

Figure 3-15: 3-in-1 Combo Reader

To install the combo reader to the POC-W24C-ULT3, please follow the steps below.

Step 1: Open the USB port cover on the left panel of the POC-W24C-ULT3.

Figure 3-16: USB Ports on the Left Panel

Step 2: Align the USB connectors on the reader with the two USB connectors on the left panel of the POC-W24C-ULT3.

Step 3: Insert and connect the USB connectors to install the combo reader.

Page 32

POC-W24C-ULT3 FHD Medical Panel PC

Step 4: Secure the combo reader to the system by inserting two retention screws

(M3x5L) into the rear panel of the POC-W24C-ULT3 and tightening them.

Figure 3-17: Combo Reader Installation

Step 5: Install the drivers for these three readers by following the instructions described in Chapter 5 :

ƒ

Section : SCR Driver

ƒ

Section : MSR Driver

ƒ

Section : Fingerprint Reader Driver

3.8 Using RFID Reader (Optional)

The POC-W24C-ULT3 may come with an optional RFID reader pre-installed inside the

bottom left corner of the front panel ( Figure 1-2

). To use the RFID reader, follow the steps below.

Step 1: Install the RFID driver (refer to

Section 5.10

).

Step 2: Locate the IRFR-100.exe file in the following folder of the driver CD:

\Docs\12.Other\POCP-MF-RFID-R10\RFID\D490. Copy the IRFR-100.exe

program to the desktop.

Page 33

POC-W24C-ULT3 FHD Medical Panel PC

Figure 3-18: RFID Program Location

Step 3: Double click the IRFR-100 icon on the desktop.

Figure 3-19: IRFR-100 Icon

Step 4:

The IRFR-100 window appears ( Figure 3-20 ).

Figure 3-20: IRFR Screen

Step 5: Select the Find tags tab and click the Run button to enable the RFID reader

( Figure 3-21 ).

Page 34

POC-W24C-ULT3 FHD Medical Panel PC

Figure 3-21: IRFR – Find Tags

Step 6: Place an RFID card near the RFID reader on the bottom right corner of the

front panel ( Figure 1-2 ) then remove it. The card number will be shown in the

UIDs column ( Figure 3-22 ).

Figure 3-22: IRFR – UIDs

Page 35

POC-W24C-ULT3 FHD Medical Panel PC

NOTE:

Please refer to the IRFR-100 user guide in the driver CD

(IRFR-100_AP_UserGuide.pdf) for detailed instruction on how to use the IRFR-100.

3.9 RS-232/422/485 Serial Port Connection

The bottom panel of the POC-W24C-ULT3 has one DB-9 male connectors for

RS-232/422/485 connection. The serial communication mode selection can be made through the BIOS options. Please refer to

Section 4.3.3.1.1

for detailed information. The

pinouts of the DB-9 connector are listed below.

Pin RS-232 RS-422 RS-485

2 RX

3 TX RXD422+

4 DTR RXD422-

5 GND

6 DSR

7 RTS

8 CTS

9 RI

Table 3-2: RS-232/422/485 Serial Port Pinouts

Page 36