- Computers & electronics
- Computer components
- System components
- Motherboards
- IEI Integration
- POC-W24C-ULT3
- User manual
B.1.1 General Safety Precautions. IEI Technology POC-W24C-ULT3 160 Pages
B.1.1 General Safety Precautions. IEI Technology POC-W24C-ULT3
advertisement
POC-W24C-ULT3 FHD Medical Panel PC
WARNING:
The precautions outlined in this chapter should be strictly followed.
Failure to follow these precautions may result in permanent damage to the POC-W24C-ULT3.
B.1 Safety Precautions
Please follow the safety precautions outlined in the sections that follow:
B.1.1 General Safety Precautions
Please ensure the following safety precautions are adhered to at all times.
To prevent the risk of electric shock, make sure power cord is unplugged from wall socket.
To fully disengage the power to the unit, please disconnect the power cord from the ac outlet. Refer servicing to qualified service personnel. The AC outlet shall be readily available and accessible.
Users must not allow SIP/SOPs and the patient to come into contact at the same time.
Grounding reliability can only be achieved when the equipment is connected to an equivalent receptacle marked “Hospital Only” or “Hospital
Grade”.
Follow the electrostatic precautions outlined below whenever the
POC-W24C-ULT3 is opened.
Make sure the power is turned off and the power cord is disconnected whenever the POC-W24C-ULT3 is being installed, moved or modified.
Do not apply voltage levels that exceed the specified voltage range .
Doing so may cause fire and/or an electrical shock. Use a power cord that matches the voltage of the power outlet, which has been approved and complies with the safety standard of your particular country.
Page 132
advertisement
Related manuals
advertisement
Table of contents
- 16 1 INTRODUCTION
- 20 1.4.1 Backlit Touch Buttons
- 28 2 UNPACKING
- 34 3 INSTALLATION
- 40 3.5.1 Using VoIP Handset
- 44 3.6.1 Barcode Reader Installation
- 46 3.6.2 Reading Light
- 52 3.10.1 AT Power Mode
- 52 3.10.2 ATX Power Mode
- 53 3.11.1 Wall Mounting
- 56 3.11.2 Arm Mounting
- 58 3.11.3 Stand Mounting
- 60 4 BIOS SETUP
- 61 4.1.1 Starting Setup
- 61 4.1.2 Using Setup
- 62 4.1.3 Getting Help
- 62 4.1.4 BIOS Menu Bar
- 65 4.3.1 Trusted Computing
- 66 4.3.2 ACPI Settings
- 67 4.3.3 F81866 Super IO Configuration
- 70 4.3.4 F81866 H/W Monitor
- 71 4.3.5 RTC Wake Settings
- 72 4.3.6 Serial Port Console Redirection
- 76 4.3.7 CPU Configuration
- 78 4.3.8 SATA Configuration
- 80 4.3.9 USB Configuration
- 81 4.3.10 IEI Feature
- 82 4.4.1 System Agent (SA) Configuration
- 86 4.4.2 PCH-IO Configuration
- 94 5 DRIVER INSTALLATION
- 107 5.11.1 SCR Driver
- 111 5.11.2 MSR Driver
- 114 5.11.3 Fingerprint Reader Driver
- 118 6 SYSTEM MAINTENANCE
- 125 7 INTERFACE CONNECTORS
- 128 7.2.1 Audio Connector (AUDIO_OUT1)
- 128 7.2.2 Audio Out Connector (AMP_OUT1)
- 128 7.2.3 Battery Connector (BAT1)
- 129 7.2.4 Debug Connector (DBG_PORT1)
- 129 7.2.5 Inverter Connector (INVERTER1)
- 129 7.2.6 LVDS Connector (LVDS1)
- 130 7.2.7 MCU Connector (HOTKEY_CN1)
- 131 7.2.8 MCU Flash Connector (JP8)
- 131 7.2.9 MCU Flash SPI ROM Connector (MCU_SPI1)
- 131 7.2.10 Microphone Connector (DMIC1)
- 132 7.2.11 Power Button Connector (PWR_BTN1)
- 132 7.2.12 Power LED Connector (PW_LED1)
- 132 7.2.13 RS-232 Serial Port Connector (COM2)
- 133 7.2.14 SATA Connectors (SATA1 & SATA2)
- 133 7.2.15 SPI Flash Connector (JSPI1)
- 133 7.2.16 TPM Connector (TPM1)
- 134 7.2.17 USB Connector (BT_USB1)
- 134 7.2.18 USB Connector (CAM_USB1)
- 135 7.2.19 USB Connector (RFID_USB1)
- 135 7.2.20 USB Connector (TOUCH_USB1)
- 136 7.3.1 GbE Connectors (LAN1 & LAN2)
- 136 7.3.2 HDMI Output Connector (HDMI_OUT1)
- 137 7.3.3 Power Connector (PWR1)
- 137 7.3.4 RS-232/422/485 DB-9 Serial Port (COM1)
- 137 7.3.5 USB 2.0 Connectors (USB20_CN1)
- 138 7.3.6 USB 3.0 Connectors (USB_CON1)
- 138 7.3.7 USB 3.0 Connectors (USB_CON2)
- 139 7.4.1 Flash Descriptor Security Override Jumper (ME_FLASH1)
- 139 7.4.2 LVDS Panel Voltage Selection Jumper (J_VLVDS1)
- 140 7.4.3 LVDS Panel Resolution Selection Jumper (SW1)
- 140 7.4.4 PCIe Mini/mSATA Mode Selection (MSATA_CN1)
- 141 A REGULATORY COMPLIANCE
- 146 B SAFETY PRECAUTIONS
- 147 B.1.1 General Safety Precautions
- 148 B.1.2 Anti-static Precautions
- 149 B.1.3 Product Disposal
- 150 B.1.4 Classification
- 151 B.2.1 Maintenance and Cleaning
- 151 B.2.2 Cleaning Tools
- 152 C BIOS MENU OPTIONS
- 155 D WATCHDOG TIMER
- 158 E HAZARDOUS MATERIALS DISCLOSURE