Product Overview. TKH Security Solutions XSNet C4108 SW (EOL), XSNet C4108 SW, XSNet C4104 SW (EOL), XSNet C4104 SW
Add to My manuals206 Pages
advertisement
XSNet C4104W/C4108W
Product Overview
Hardened Managed Ethernet Switch
Front View
Package Contents
When you unpack the product package, you shall find the items listed below. Please inspect the contents, and report any apparent damage or missing items immediately to your authorized reseller.
The Hardened Managed Ethernet Switch
User’s
RS232
10
XSNet C4104W/C4108W
Product Highlights
Basic Features
Complies with EN50121-4 environmental requirements for railway applications.
Meets NEMA TS2 Environmental requirements such as temperature, shock, and vibration for traffic control equipment.
Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity for industrial environment.
Manageable via SNMP, Web-based, Telnet, and RS-232 console port.
Supports Command Line Interface in RS-232 console.
Supports 802.3/802.3u/802.3ab/802.3z/802.3x. Auto-negotiation:
10/100/1000Mbps, full/half-duplex. Auto MDI/MDIX.
The C4104SW is equipped with 2x 100Base-FX SFP slots.
The C4108SW is equipped with 2x 1000Base-FX SFP slots.
Supports 8192 MAC addresses. Provides 2M bits memory buffer.
Alarms for power and port link failure by relay output.
Power Supply: Redundant DC Terminal Block power inputs or 12VDC
DC JACK with 100-240VAC external power supply.
Operating voltage and Max. current consumption: 0.92A @ 12VDC,
0.46A @ 24VDC, 0.23A @ 48VDC. Power consumption: 11W Max.
-40°C to 75°C (-40°F to 167°F) operating temperature range. Tested for functional operation @ -40°C to 85°C (-40°F to 185°F).
Supports DIN-Rail and Panel Mounting installation.
<Note> Press reset button more than 10 seconds to restart Managed Switch and reset Managed Switch password to factory default (no password required on default setting).
Management Support
VLAN
Port-based
IEEE802.1Q tagged VLAN
TRUNKING
Port
IEEE802.3ad Link Aggregation Control Protocol
PORT-SECURITY
Per-port programmable MAC address locking
Up to 24 Static Secure MAC addresses per port
IEEE802.1x Port-based Network Access Control
11
XSNet C4104W/C4108W
PORT-MIRRORING
Port-mirroring
QOS
(IEEE802.1p Quality of Service)
4 priority queues
INTERNETWORKING PROTOCOLS
Bridging:
IEEE802.1s Multiple Spanning Tree
IEEE802.1w Rapid Spanning Tree
IEEE802.1D Spanning Tree compatible
IEEE802.1Q – GVRP
IEEE802.1p – GMRP
Ring
Chain
IP
IGMP Snooping
Rate
NTP
NETWORK MANAGEMENT METHODS
Console port access via RS-232 cable (CLI, Command Line Interface)
Telnet remote access
agent:
MIB-2 (RFC1213)
Bridge MIB (RFC1493)
RMON MIB (RFC2819) – statistics, history, alarm and events
VLAN MIB (IEEE802.1Q/RFC2674)
Private MIB
Web
TFTP software-upgrade capability
12
XSNet C4104W/C4108W
Front Panel Display
POWER
This LED comes on when the switch is properly connected to power and turned on.
Port Status LEDs
The LEDs are located on the front panel, displaying status for each respective port. Please refer to the following table for more details.
13
XSNet C4104W/C4108W
Power 1
Power 2
Power 3
Steady Power on
10/100Base-TX, 100Base SFP
LINK/ACT
Steady A valid network connection established
Flashing
Transmitting or receiving data
ACT stands for ACTIVITY
100 Steady Connection at 100Mbps speed
1000Base SFP
LINK/ACT
Steady A valid network connection established
Flashing
Transmitting or receiving data
ACT stands for ACTIVITY
1000 Steady Connection at 1000Mbps speed
Physical Ports
The Hardened Managed Ethernet Switch provides:
Number of ports
10/100Base-TX 100Base-FX/BX
100Base SFP
Gigabit:
1000Base SFP
8 0 2
4 2 0
CONNECTIVITY
RJ-45 connectors on TX ports
Duplex LC connector on SFP 100Base-FX/BX fiber transceiver
Duplex LC connector on SFP 1000Base-SX/LX/BX fiber transceiver
MODE SELECTION
10Base-T full-duplex mode
10Base-T half-duplex mode
100Base-TX full-duplex mode
100Base-TX half-duplex mode
100Base-FX full-duplex mode
1000Base-SX/LX full-duplex mode
Auto-negotiating mode
14
XSNet C4104W/C4108W
Switch Management
Web-based browser interface
The switch also boasts a point-and-click browser-based interface that lets user access full switch configuration and functionality from a
Netscape or Internet Explorer browser.
Administration console via RS-232 serial port (CLI)
The switch provides an onboard serial port, which allows the switch to be configured via a directly connected terminal.
External SNMP-based network management application
The switch can also be configured via SNMP.
15
advertisement
Related manuals
advertisement
Table of contents
- 1 Manual
- 1 Quick Start Guide
- 1 This quick start guide describes how to install and use the Hardened Managed Ethernet Switch. This is the switch of choice for harsh environments constrained by space.
- 1 Physical Description
- 1 The Port Status LEDs and Power Inputs
- 2 Functional Description
- 3 Console Configuration
- 5 Web Configuration
- 7 Preface
- 8 Table of Contents
- 10 Product Overview
- 10 Hardened Managed Ethernet Switch
- 10 Package Contents
- 11 Product Highlights
- 11 Basic Features
- 11 Management Support
- 11 VLAN
- 11 TRUNKING
- 11 PORT-SECURITY
- 12 PORT-MIRRORING
- 12 QOS (IEEE802.1p Quality of Service)
- 12 INTERNETWORKING PROTOCOLS
- 12 NETWORK MANAGEMENT METHODS
- 13 Front Panel Display
- 13 This LED comes on when the switch is properly connected to power and turned on.
- 13 The LEDs are located on the front panel, displaying status for each respective port. Please refer to the following table for more details.
- 14 Physical Ports
- 14 CONNECTIVITY
- 14 MODE SELECTION
- 15 Switch Management
- 15 Web-based browser interface
- 15 Administration console via RS-232 serial port (CLI)
- 15 External SNMP-based network management application
- 16 Installation
- 16 Selecting a Site for the Switch
- 17 Connecting to Power
- 17 12VDC DC Jack
- 17 Redundant DC Terminal Block Power Inputs
- 17 Alarms for Power Failure
- 18 Connecting to Your Network
- 18 Cable Type & Length
- 20 Cabling
- 21 Switch Management
- 21 Management Access Overview
- 21 Administration Console (CLI)
- 22 Direct Access
- 22 [DEFAULT PARAMETERS]
- 22 Web Management
- 23 SNMP-Based Network Management
- 23 Protocols
- 23 VIRTUAL TERMINAL PROTOCOLS, SUCH AS TELNET
- 23 A virtual terminal protocol is a software program, such as Telnet, that allows you to establish a management session from a Macintosh, a PC, or a UNIX workstation. Because Telnet runs over TCP/IP, you must have at least one IP address configured on the switch before you can establish access to it with a virtual terminal protocol.
- 23 SIMPLE NETWORK MANAGEMENT PROTOCOL (SNMP)
- 23 SNMP is the standard management protocol for multivendor IP networks. SNMP supports transaction-based queries that allow the protocol to format messages and to transmit information between reporting devices and data-collection programs. SNMP runs on top of the User Datagram Protocol (UDP), offering a connectionless-mode service.
- 24 Management Architecture
- 25 SNMP & RMON Management
- 25 Overview
- 25 - The RMON probe is an intelligent device or software agent that continually collects statistics about a LAN segment or VLAN. The RMON probe transfers the collected data to a management workstation on request or when a pre-defined threshold is reached.
- 25 - The management workstation collects the statistics that the RMON probe gathers. The workstation can reside on the same network as the probe, or it can have an in-band or out-of-band connection to the probe.
- 26 SNMP Agent and MIB-2 (RFC 1213)
- 26 - Retrieving MIB counters from various layers of software modules according to the SNMP GET/GET NEXT frame messages.
- 26 - Setting MIB variables according to the SNMP SET frame message.
- 26 - Generating an SNMP TRAP frame message to the Network Management Station if the threshold of a certain MIB counter is reached or if other trap conditions (such as the following) are met:
- 26 WARM START
- 26 COLD START
- 26 LINK UP
- 26 LINK DOWN
- 26 AUTHENTICATION FAILURE
- 26 RISING ALARM
- 26 FALLING ALARM
- 26 TOPOLOGY ALARM
- 26 RMON MIB (RFC 2819) and Bridge MIB (RFC 1493)
- 27 RMON Groups Supported
- 27 - RMON Statistics Group – maintains utilization and error statistics for the switch port being monitored.
- 27 - RMON History Group – gathers and stores periodic statistical samples from the previous Statistics Group.
- 27 - RMON Alarm Group – allows a network administrator to define alarm thresholds for any MIB variable. An alarm can be associated with Low Threshold, High Threshold, or both. A trigger can trigger an alarm when the value of a specific MIB variable exceeds a threshold, falls below a threshold, or exceeds or falls below a threshold.
- 27 - RMON Event Group – allows a network administrator to define actions based on alarms. SNMP Traps are generated when RMON Alarms are triggered. The action taken in the Network Management Station depends on the specific network management application.
- 27 Bridge Groups Supported
- 27 - The dot1dBase Group – a mandatory group that contains the objects applicable to all types of bridges.
- 27 - The dot1dStp Group – contains objects that denote the bridge’s state with respect to the Spanning Tree Protocol. If a node does not implement the Spanning Tree Protocol, this group will not be implemented. This group is applicable to any transparent only, source route, or SRT bridge that implements the Spanning Tree Protocol.
- 27 - The dot1dTp Group – contains objects that describe the entity’s transparent bridging status. This group is applicable to transparent operation only and SRT bridges.
- 27 - The dot1dStatic Group – contains objects that describe the entity’s destination-address filtering status. This group is applicable to any type of bridge which performs destination-address filtering.
- 28 Web-Based Browser Management
- 28 Logging on to the switch
- 29 SWITCH IP ADDRESS
- 29 LOGIN
- 29 Enter the factory default login ID: root.
- 29 PASSWORD
- 29 Enter the factory default password (no password).
- 30 Understanding the Browser Interface
- 30 SYSTEM
- 30 System Information, System Name/Password, IP Address, ARP Table, Route Table, Save Configuration, Firmware Upgrade, Alarm Setting, Reboot, Logout
- 30 PORT
- 30 Configuration, Port Status, Rate Control, RMON Statistics, Per Port Vlan Activities, Port Security
- 30 SWITCHING
- 30 Bridging, Static MAC Entry, Port Mirroring
- 31 TRUNKING
- 31 Port Trunking, LACP Trunking
- 31 STP / RING
- 31 VLAN
- 31 VLAN Mode Setting, 802.1Q VLAN Setting, 802.1Q Port Setting, Port Based VLAN
- 31 QOS
- 31 Global Configuration, 802.1p Priority, DSCP
- 31 SNMP
- 31 802.1X
- 31 OTHER PROTOCOLS
- 32 System
- 32 System Information
- 36 ARP Table
- 37 Route Table
- 44 Alarm Setting
- 47 Port
- 53 Switching
- 56 Trunking
- 58 STP / Ring
- 68 Chain Setting
- 69 VLAN
- 76 QoS
- 79 SNMP
- 84 802.1x
- 87 Port Authentication
- 88 Other Protocols
- 98 Command Line Console Management
- 98 Administration Console
- 99 Exec Mode (View Mode)
- 103 Privileged Exec Mode (Enable Mode)
- 108 Configure Mode (Configure Terminal Mode)
- 112 User Interface Configuration
- 112 Http Server, Http Secure-Server, Telnet, SSH
- 114 System
- 114 System Information, System Name/Password, IP Address, ARP Table, Route Table, Save Configuration, Firmware Upgrade, Alarm Setting, Reboot, Logout
- 125 Port
- 125 Configuration, Port Status, Rate Control, RMON Statistics, Per Port Vlan Activities, Port Security
- 132 Switching
- 132 Bridging, Static MAC Entry, Port Mirroring
- 137 Trunking
- 137 Port Trunking, LACP Trunking
- 142 STP / Ring
- 142 Global Configuration, RSTP Port Setting, MSTP Properties, MSTP Instance Setting, MSTP Port Setting, Ring Setting, Chain Setting
- 156 Chain Setting
- 158 VLAN
- 158 VLAN Mode Setting, 802.1Q VLAN Setting, 802.1Q Port Setting, Port Based VLAN
- 164 QoS
- 167 SNMP
- 174 802.1x
- 179 Other Protocols
- 197 Specifications
- 197 LED Indicators
- 197 Operating
- 197 Temperature
- 199 Appendix A
- 200 Appendix B