Installation. TKH Security Solutions XSNet C4108 SW (EOL), XSNet C4108 SW, XSNet C4104 SW (EOL), XSNet C4104 SW

XSNet C4104W/C4108W

Installation

This chapter gives step-by-step instructions about how to install the switch:

Selecting a Site for the Switch

As with any electric device, you should place the switch where it will not be subjected to extreme temperatures, humidity, or electromagnetic interference. Specifically, the site you select should meet the following requirements:

-The ambient temperature should be between -40°C to 75°C (-40°F to

167°F).

-The relative humidity should be less than 95 percent, non-condensing.

-Surrounding electrical devices should not exceed the electromagnetic field

(RFC) standards.

-Make sure that the switch receives adequate ventilation. Do not block the ventilation holes on each side of the switch.

16

XSNet C4104W/C4108W

Connecting to Power

Redundant DC Terminal Block Power Inputs or 12VDC DC

Jack:

12VDC DC Jack

Step 1: Connect the supplied AC to DC power adapter to the receptacle on the topside of the switch.

Step 2: Connect the power cord to the AC to DC power adapter and attach the plug into a standard AC outlet with the appropriate AC voltage.

Redundant DC Terminal Block Power Inputs

There are two pairs of power inputs for use with redundant power sources. You only need to have one power input connected to run the switch.

Step 1: Connect the DC power cord to the plug-able terminal block on the switch, and then plug it into a standard DC outlet.

Step 2: Disconnect the power cord if you want to shut down the switch.

Top View

Alarms for Power Failure

Step 1: There are two pins on the terminal block used for power failure detection. It provides the normally closed output when the power

17

XSNet C4104W/C4108W source is active. Use this as a dry contact application to send a signal for power failure detection.

Power Input Assignment

Power2

Power1

＋

－

＋

－

12-48VDC

Power Ground

12-48VDC

Power Ground

Terminal

Block

Earth Ground

Relay Output Rating 1A @ 24VDC

Relay Alarm Assignment

FAULT

*Warning signal disable for following:

The relay contact closes if Power1 and Power2 are both failed but Power3 on.

The relay contact closes if Power3 is failed but

Power1 and Power2 are both on.

Special note:

The relay output is normal open position when there is no power to the switch. Please do not connect any power source to this terminal to prevent shorting your power supply.

Connecting to Your Network

Cable Type & Length

It is necessary to follow the cable specifications below when connecting the switch to your network. Use appropriate cables that meet your speed and cabling requirements.

Cable Specifications

18

XSNet C4104W/C4108W

Speed Connector Port

Speed

Half/Full

Duplex

Cable Max.

Distance

UTP/STP

100 m

Cat. 3, 4, 5

100 m 100Base-TX RJ-45 100/200

Mbps UTP/STP

Cat. 5

1000Base-T RJ-45 2000

UTP/STP

Cat. 5

SFP

100 m

100Base-FX

100Base-FX

100Base-BX

100Base-BX

1000Base-SX

1000Base-LX

1000Base-BX

Duplex LC

Duplex LC

Duplex LC

Duplex LC

Duplex LC

Duplex LC

Duplex LC

200 Mbps MMF

(62.5

μ m)

2 km

200 Mbps SMF (10 μ m) 20, 40, 75,

100 km

200 Mbps MMF

(62.5

μ m)

2, 5 km

200 Mbps SMF (10 μ m) 20, 40 km

2000 Mbps MMF

(62.5

μ m)

550 m

2 km

2000 Mbps SMF (9 μ m) 10, 40, 60 km

2000 Mbps SMF (9 μ m) 70

19

XSNet C4104W/C4108W

Cabling

Step 1: First, ensure the power of the switch and end devices are turned off.

<Note> Always ensure that the power is off before any installation.

Step 2: Prepare cable with corresponding connectors for each type of port in use.

Step 3: Consult Cable Specifications Table on previous page for cabling requirements based on connectors and speed.

Step 4: Connect one end of the cable to the switch and the other end to a desired device.

Step 5: Once the connections between two end devices are made successfully, turn on the power and the switch is operational.

20