advertisement
Assembly
1
Center panel installation
Locate the Center Left Front Panel (B), Center Right
Front Panel (C), Center Front Panel (D), and set out face down on a scratch-free surface.
Connect the Center Left Front Panel (B), Center
Right Front Panel (C) and Center Front Panel (D) with
Connection Plate (GG).
Tighten Screws (EE) through the pre-drilled holes.
2
Outer panel installation
Insert one Wood Dowel (CC) into each of the pre-drilled holes.
Push the Left Side Panel (E) and Right Side Panel (F) snug to the Center Front Panel (D). Make sure the Wood
Dowels are seated in the pre-drilled holes.
Connect the Left Side Panel (E), Right Side Panel (F). and Center Front Panel (D) with Connection Plate (GG).
Tighten Screws (EE) through the pre-drilled holes.
Hardware Used
Part
EE
GG
Description
Screw
Connection Plate (pre-attached)
Qty
2
2
Hardware Used
Part
CC
EE
GG
Description
Wood Dowel
Screw
Connection Plate (pre-attached)
2
2
Qty
4
GG
GG
EE
D
CC
EE
CC
E
B
C F
7
HAMPTONBAY.COM
Please contact 1-877-527-0313 for further assistance.
Assembly (continued)
3
Base installation
Locate Hearth/Base (A) and set out finished side up on the floor.
Insert one Wood Dowel (CC) into each of the pre-drilled holes.
Using two (2) persons lift and attach the completed front assembly from step 2 to the Hearth/Base (A). Make sure that Wood Dowels (CC) are seated into the pre-drilled holes in the hearth/base.
Using Bolt (AA) and Washer (BB) attach panels through pre-drilled holes in the mounting blocks.
HAND TIGHTEN ONLY.
Hardware Used
Part
AA
BB
CC
Description
Bolt
Washer
Wood Dowel
8
8
Qty
8
4
Center shelf installation
Insert one Wood Dowel (CC) into each of the pre-drilled holes on the top edges of the Assembly from step 3.
Locate Center Shelf (G) and lay finished side up on top of completed assembly.
From the inside, attach Center Shelf (G) using Bolt (AA) and Washer (BB) through the pre-drilled holes in the mounting blocks.
HAND TIGHTEN ONLY.
Hardware Used
Part
AA
BB
CC
Description
Bolt
Washer
Wood Dowel
G
Qty
10
10
9
CC
CC
AA
BB
BB
AA CC
A
5
Upper panel installation
Insert one Wood Dowel (CC) into each of the pre-drilled holes.
Push the Left Upper Side Panel (I) and Right Upper Side Panel (J) snug to the Center Upper Front Panel (H). Make sure the Wood
Dowels are seated in the pre-drilled holes.
Connect the Left Upper Side Panel (I), Right Up per Side Panel (J) and Center Upper Front Panel (H) with Connection Plate (GG).
Tighten Screws (EE) through the pre-drilled holes.
Hardware Used
Part
CC
EE
GG
Description
Bolt
Washer
Connection Plate (pre-attached)
Qty
4
2
2
8
CC
GG
J
H
EE
CC
I
Assembly (continued)
6
Center shelf installation
Insert one Wood Dowel (CC) into each of the pre-drilled holes.
Using two (2) persons lift and attach the completed front assembly from step 5 to the Center Shelf (G) as shown in diagram.
Make sure that Wood Dowels (CC) are seated into the pre-drilled holes in the hearth/base.
Using Bolt (AA) and Washer (BB) attach panels through pre-drilled holes in the mounting blocks. HAND TIGHTEN
ONLY.
Hardware Used
Part
AA
BB
CC
Description
Bolt
Washer
Wood Dowel
4
4
Qty
4
7
Mantel top installation
Insert one Wood Dowel (CC) into each of the pre-drilled holes on the top edges of the Assembly from step 6.
Locate Mantel/Top (K) and lay finished side up on top of completed assembly.
From the inside, attach Mantel/Top (K) using Bolt (AA) and Washer (BB) through the pre-drilled holes in the mounting blocks. HAND TIGHTEN ONLY.
Using Phillips head screwdriver tighten all Bolts alternating top and bottom, left and right.
Hardware Used
Part
AA
BB
CC
Description
Bolt
Washer
Wood Dowel
Qty
6
6
5
K
AA
BB
CC
CC
CC
CC
G
AA
BB
8
Back panel installation
Attach Back Panel (M) and Center Back Panel (L) to the back of the completed assembly from step 7.
Insert screws (EE) through the pre-drilled holes in the Back
Panels to the completed assembly. Hand tighten.
Use a Phillips Head Screwdriver to tighten the bolts that were hand tightened.
Hardware Used
Part
EE
Description
Screw
Qty
37
M
9
EE
EE
L
M
HAMPTONBAY.COM
Please contact 1-877-527-0313 for further assistance.
Assembly (continued)
9
Door installation
Locate Right Front Door (O) and Left Front Door (N), and slide door hinge keyhole into panel hinge bracket.
(Diagram 1)
Use a Phillips Head Screwdriver to tighten screws.
(Diagram 2)
TO ADJUST HINGES:
To adjust door forward or backward change keyhole slot position. (As Shown In Diagram 3a)
To adjust door right or left loosen/tighten screw. (As Shown In Diagram 3b)
To adjust door up or down adjust bracket height.
(As Shown In Diagram 3c)
Attach the Knob (FF) to the Left Front Door (N) and
Right Front Door (O), use the bolts attached through the pre-drilled holes in the doors.
Use a Phillips Head Screwdriver to tighten the bolts.
Hardware Used
Part
FF
Description
Knob
Qty
2
10
Wood shelf installation
Choose desired height of Shelf (P) and place the four Shelf Pin (DD) into same height shelf holes inside side panels.
Insert Wood Shelf (P), allowing Wood Shelf (P) to rest on the Shelf Pin (DD).
Hardware Used
Part
DD
Description
Shelf Pin
Qty
8
P
DD
N
O
FF
10
Assembly (continued)
11
Insert installation
Lift insert carefully into the back of the unit and center in the insert opening. Do not drag insert across
Hearth/Base (A) as it may scratch your unit.
Connect the Insert Support Bar (Q) to the inside Left and Right panels, using the Bolts (AA) and Washers
(BB) through pre-drilled holes.
NOTE: Please read all “electric fireplace insert” instructions prior to installing electric insert in your completed fireplace mantel. Install the insert in your fireplace close to its final position.
NOTE: Use great care to move your completed unit. Move it only short distances, and use two people to move it into its final position.
Hardware Used
Part
AA
BB
Description
Bolt
Washer
Qty
2
2
Completed
Unit
Q
Install
Insert
From
Back
Electric
Fireplace Insert
AA BB
CAUTION: Cold climate installation recommendation: When installing this unit against a non-insulated exterior wall or chase, it is mandatory that the outer walls be insulated to conform to applicable insulation codes.
CAUTION: A 15-Amp, 120-V, 60 Hz circuit with a properly grounded outlet is required. Preferably, the fireplace will be on a dedicated circuit as other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the heater is in operation. The unit comes standard with 6-ft. three-wire cord, exiting from the rear of the fireplace. Avoid using an extension cord. If an extension cord must be used, it must be a minimum 14 AWG, three wire with grounding type plug connector and rated not less than 1875 watts. Do not use an extension cord more than 20 ft. in length.
11
HAMPTONBAY.COM
Please contact 1-877-527-0313 for further assistance.
advertisement
