Specifications. BALZER FIELD FLOATER 6 108 Pages
advertisement
Specifications
FIGURE 4
TECHNICAL DATA
12
Dimensions
Tire Pressure
28L X 26 R3
28LR26 R3
30 5 X 32 R1
30 5 X 32 R3
30 5LR32 R1
30 5LR32 R3
850/50 30 5
900/60 32 R1
See”Dimensions” on Page 12
26 PSI
(180 kPa)
54 PSI
(372 kPa)
33 PSI
(228 kPa)
33 PSI
(228 kPa)
52 PSI
(359 kPa)
52 PSI
(359 kPa)
37 PSI
(256 kPa)
35 PSI
(241 kPa)
Lug Nuts
Brake Type
Torque to 450 FT/LBS
Disc
Hydraulic Operating Pressure Up to 3000 PSI
(20 68 MPa)
Electrical System
Electrical Connection
Maximum Tow Speed
12 VDC
7-Way Receptacle
20 MPH
(32 KPH)
TRACTOR REQUIREMENTS
Tractor Horsepower
1450 Bushel
1700 Bushel
2200 Bushel
250 hp
250 hp
300 hp
PTO Horsepower
Minimum
PTO Speed
200 hp
1000 RPM
Drawbar Max Vertical Load 4,100 lbs (CAT-3)
(1860 kgs)
Drawbar Clevis Pin Diameter
PTO to Drawbar Distance
2”
(5 cm)
16” to 20”
(40 cm to 50 cm)
Drawbar to Ground Height Distance 15” to 22”
(38 cm to 56 cm)
Tractor Hydraulic Flow
PTO
Hydraulic Control Block
10 GPM
(37 8 LPM)
10 GPM
(37 8 LPM)
Tractor Hydraulic Pressure
Tractor Hydraulic Outlets
Electrical Connection
Up to 3,000 PSI
(20 68 MPa)
Min: 1 / Max: 2
7-pin Round
Field Floater 6 Grain Cart User Manual
advertisement
Related manuals
advertisement
Table of contents
- 5 Company Statements
- 5 Accuracy
- 6 Contact Information
- 9 Safety
- 10 Mandatory Safety Shutdown Procedure
- 12 Vertical Auger Safety
- 13 PTO Operation Safety
- 16 Specifications
- 17 Dimensions
- 20 Pre-Operation Checks
- 22 Jack Storage
- 35 Quick Start Up and Use
- 36 Optional Roll Top Cover
- 36 Closing Roll Top Cover
- 37 Opening Roll Top Cover
- 39 Maintenance
- 40 Daily and Before Start of Season
- 49 Automatic Oiler
- 49 Before Start of Season
- 49 Daily Maintenance Checks
- 49 End of Season/Preparing for Storage
- 50 Auger Drive System
- 53 Troubleshooting
- 54 Steering Not Working Correctly
- 54 Brakes Not Working Properly
- 55 Automatic Oiler Not Working
- 56 Abnormal Auger Vibrations When Unloading
- 57 Upper Vertical Auger “Slams” Open
- 57 Joystick Will Not Work
- 57 Host Indicator Not Working/Error Codes
- 58 Scale Indicator Not Working/Error Codes
- 61 Weigh System Programming
- 62 Using Memory Locations
- 62 Naming a Memory Location
- 63 Storing to a Memory Location
- 64 Remove Weight from Memory Location
- 64 Recall a Memory Location
- 65 Export a Memory Location to USB
- 65 Export All Memory Locations to USB
- 66 Clear a Memory Location
- 66 Host Indicator Programming
- 66 Menu System Selection
- 67 Main Menu System
- 67 Clear All Memory Locations
- 68 Set Time and Date
- 69 Set Display Backlight
- 69 Set Weighing Units
- 69 Adjust Average Rate
- 70 Set Auto Power Off for Host Indicator
- 70 Set Hold Enable for Host Indicator
- 70 Set Print Continuous for Data Output
- 71 Set RS232 Port Baud Rate
- 71 Calibration Menu System
- 72 Set for Read Only Mode
- 72 Set Radio Enable
- 72 Set Radio Channel
- 73 Set Radio Channel Network ID
- 73 Set Radio Channel Encryption Key
- 73 Reset Radio to Default Settings
- 74 Scale Indicator Programming
- 75 Menu System Selection
- 75 Main Menu System
- 75 Set Display Backlight
- 75 Set Weighing Units
- 75 Adjust Average Rate
- 76 Set Auto Power Off for Scale Indicator
- 76 Set Hold Enable for Scale Indicator
- 76 Set RS232 Port Baud Rate
- 76 Calibration Menu System
- 76 Set Radio Enable
- 76 Set Radio Channel
- 76 Set Radio Channel Network ID
- 77 Set Radio Channel Encryption Key
- 77 Reset Radio to Default Settings
- 77 Set for Weigh Unit Changeable in Main Menu
- 77 Set Auto Zero Tracking
- 77 Set Graduation Size
- 79 Notes
- 89 Company Statements
- 89 Accuracy
- 89 To the Purchaser
- 89 Warranty Manufacture
- 90 Liability for Delays
- 90 Contact Information
- 91 Technical Data
- 93 Operation
- 94 Pre-Operation Checks
- 94 Track Break-in
- 94 Track Tension
- 95 Track Alignment
- 96 Maximizing Tread Life
- 97 Maintenance
- 98 Daily
- 98 Track Maintenance
- 99 Periodic Storage
- 99 Long Term Storage
- 100 Adjusting Track Tension
- 101 Adjusting Alignment
- 103 Notes