Optional Roll Top Cover. BALZER FIELD FLOATER 6 108 Pages
advertisement
OPERATION
Grain Cart Weigh System Operation (Continued)
FIGURE 35
Button
Press
Zero Scale without Tare Weight Set
Screen
Display Description
Button
Press
Zero Scale with Tare Weight Set
Screen
Display Description
GROSS
Scale GROSS weight set to zero NET
Showing negative NET weight because NET weight is GROSS weight less TARE weight
When you have filled the grain cart, should you want to unload a specific weight of grain, press the This will set the gross weight as the tare weight and switch the display to NET with zero as the Net weight The displayed net weight will show zero
As you unload the grain cart, the display will show a negative number Stop unloading when the desired amount of grain has been removed from the grain cart ( Figure 36 )
Should you need to set the tare weight again, you will need to press and the at the same time to clear the currently recorded tare weight, then press
Button
Press
to set the new tare weight
FIGURE 36
Set TARE Weight with Full Grain Cart
Screen
Display Description
Weight of grain in cart
Button
Press
GROSS
Clear TARE Weight and Set New TARE Weight
Screen
Display Description
TARE weight cleared and system changing to
GROSS weight
NET
NET
GROSS
NET weight zeroed with above weight set as TARE weight
10,000 lbs of grain unloaded from cart
Remaining weight of grain in cart
GROSS
NET
Weight of grain in cart
NET weight zeroed with above weight set as TARE weight
Optional Roll Top Cover
This Balzer Grain Cart may be equipped with a roll top cover to protect the loaded contents of the grain cart from wind and adverse weather
Closing Roll Top Cover
Remove the crank handle from the crank retainer and hold away from the grain cart body at about a 45 ° angle ( Figure 37 )
Hold the crank handle firmly with both hands and roll the cover until it falls just under the latch plate ( Figure 38 )
Bring the crank arm perpendicular to the ground and parallel to the back of the grain cart to lock the crank arm and cover shaft
( Figure 39 )
32 Field Floater 6 Grain Cart User Manual
advertisement
Related manuals
advertisement
Table of contents
- 5 Company Statements
- 5 Accuracy
- 6 Contact Information
- 9 Safety
- 10 Mandatory Safety Shutdown Procedure
- 12 Vertical Auger Safety
- 13 PTO Operation Safety
- 16 Specifications
- 17 Dimensions
- 20 Pre-Operation Checks
- 22 Jack Storage
- 35 Quick Start Up and Use
- 36 Optional Roll Top Cover
- 36 Closing Roll Top Cover
- 37 Opening Roll Top Cover
- 39 Maintenance
- 40 Daily and Before Start of Season
- 49 Automatic Oiler
- 49 Before Start of Season
- 49 Daily Maintenance Checks
- 49 End of Season/Preparing for Storage
- 50 Auger Drive System
- 53 Troubleshooting
- 54 Steering Not Working Correctly
- 54 Brakes Not Working Properly
- 55 Automatic Oiler Not Working
- 56 Abnormal Auger Vibrations When Unloading
- 57 Upper Vertical Auger “Slams” Open
- 57 Joystick Will Not Work
- 57 Host Indicator Not Working/Error Codes
- 58 Scale Indicator Not Working/Error Codes
- 61 Weigh System Programming
- 62 Using Memory Locations
- 62 Naming a Memory Location
- 63 Storing to a Memory Location
- 64 Remove Weight from Memory Location
- 64 Recall a Memory Location
- 65 Export a Memory Location to USB
- 65 Export All Memory Locations to USB
- 66 Clear a Memory Location
- 66 Host Indicator Programming
- 66 Menu System Selection
- 67 Main Menu System
- 67 Clear All Memory Locations
- 68 Set Time and Date
- 69 Set Display Backlight
- 69 Set Weighing Units
- 69 Adjust Average Rate
- 70 Set Auto Power Off for Host Indicator
- 70 Set Hold Enable for Host Indicator
- 70 Set Print Continuous for Data Output
- 71 Set RS232 Port Baud Rate
- 71 Calibration Menu System
- 72 Set for Read Only Mode
- 72 Set Radio Enable
- 72 Set Radio Channel
- 73 Set Radio Channel Network ID
- 73 Set Radio Channel Encryption Key
- 73 Reset Radio to Default Settings
- 74 Scale Indicator Programming
- 75 Menu System Selection
- 75 Main Menu System
- 75 Set Display Backlight
- 75 Set Weighing Units
- 75 Adjust Average Rate
- 76 Set Auto Power Off for Scale Indicator
- 76 Set Hold Enable for Scale Indicator
- 76 Set RS232 Port Baud Rate
- 76 Calibration Menu System
- 76 Set Radio Enable
- 76 Set Radio Channel
- 76 Set Radio Channel Network ID
- 77 Set Radio Channel Encryption Key
- 77 Reset Radio to Default Settings
- 77 Set for Weigh Unit Changeable in Main Menu
- 77 Set Auto Zero Tracking
- 77 Set Graduation Size
- 79 Notes
- 89 Company Statements
- 89 Accuracy
- 89 To the Purchaser
- 89 Warranty Manufacture
- 90 Liability for Delays
- 90 Contact Information
- 91 Technical Data
- 93 Operation
- 94 Pre-Operation Checks
- 94 Track Break-in
- 94 Track Tension
- 95 Track Alignment
- 96 Maximizing Tread Life
- 97 Maintenance
- 98 Daily
- 98 Track Maintenance
- 99 Periodic Storage
- 99 Long Term Storage
- 100 Adjusting Track Tension
- 101 Adjusting Alignment
- 103 Notes