Set RS232 Port Baud Rate. BALZER FIELD FLOATER 6 108 Pages
advertisement
WEIGH SYSTEM PROGRAMMING
Host Indicator Programming (Continued)
Set RS232 Port Baud Rate
The following steps will set the output data rate of the RS232 serial port to match that of an external display/reporting device
Step Button Entry Option Display
Set Baud Rate
Select Baud Rate The default selection is 9600 - display will be flashing
Cycle through baud rate selections of 1200,
2400, 4800, 9600, 19200, 38400, 57600, and
115200
Accept your selection
Calibration Menu System
The following options are accessible through the calibration menu system:
Display Function Definition
Calibration Step Code Default is 000 This continues through the main calibration menu There are no user serviceable Calibration Sub menus
Read Only Mode
Radio Enable
Radio Channel
This option is for when multiple host indicators are used with the same scale indicator It is not applicable to this grain cart configuration as it is delivered
Allows the host indicator to communication wirelessly with other compatible equipment and devices
Sets the radio channel when the radio is enabled There are 12 radio channels available
Radio Network ID Sets the radio’s network identification (0-65534) for the radio channel being used
Radio Encryption
Enable and Key
Restore Radio
Defaults
Turning on the radio encryption makes the transmitted signal unable to be decoded without the receiver having the same encryption key (encryption key value range: 0-65534) NOTE: IF YOU FORGET THE ENCRYPTION
KEY VALUE, YOU WILL NOT BE ABLE TO CONNECT A RECEIVING
DEVICE
Default is 0 This leaves the radio settings as they have been programmed
Entering 3 will restore the radio settings to their default values
Unit Switch Enable Allows the changing of weighing units from pounds (lbs) to kilograms (kg) through the main menu
Auto Zero Tracking Automatic adjustment to the scale should the zero reading drift from the set zero of the scale
Graduation Size Set weighing incremental count
Field Floater 6 Grain Cart User Manual 67
advertisement
Related manuals
advertisement
Table of contents
- 5 Company Statements
- 5 Accuracy
- 6 Contact Information
- 9 Safety
- 10 Mandatory Safety Shutdown Procedure
- 12 Vertical Auger Safety
- 13 PTO Operation Safety
- 16 Specifications
- 17 Dimensions
- 20 Pre-Operation Checks
- 22 Jack Storage
- 35 Quick Start Up and Use
- 36 Optional Roll Top Cover
- 36 Closing Roll Top Cover
- 37 Opening Roll Top Cover
- 39 Maintenance
- 40 Daily and Before Start of Season
- 49 Automatic Oiler
- 49 Before Start of Season
- 49 Daily Maintenance Checks
- 49 End of Season/Preparing for Storage
- 50 Auger Drive System
- 53 Troubleshooting
- 54 Steering Not Working Correctly
- 54 Brakes Not Working Properly
- 55 Automatic Oiler Not Working
- 56 Abnormal Auger Vibrations When Unloading
- 57 Upper Vertical Auger “Slams” Open
- 57 Joystick Will Not Work
- 57 Host Indicator Not Working/Error Codes
- 58 Scale Indicator Not Working/Error Codes
- 61 Weigh System Programming
- 62 Using Memory Locations
- 62 Naming a Memory Location
- 63 Storing to a Memory Location
- 64 Remove Weight from Memory Location
- 64 Recall a Memory Location
- 65 Export a Memory Location to USB
- 65 Export All Memory Locations to USB
- 66 Clear a Memory Location
- 66 Host Indicator Programming
- 66 Menu System Selection
- 67 Main Menu System
- 67 Clear All Memory Locations
- 68 Set Time and Date
- 69 Set Display Backlight
- 69 Set Weighing Units
- 69 Adjust Average Rate
- 70 Set Auto Power Off for Host Indicator
- 70 Set Hold Enable for Host Indicator
- 70 Set Print Continuous for Data Output
- 71 Set RS232 Port Baud Rate
- 71 Calibration Menu System
- 72 Set for Read Only Mode
- 72 Set Radio Enable
- 72 Set Radio Channel
- 73 Set Radio Channel Network ID
- 73 Set Radio Channel Encryption Key
- 73 Reset Radio to Default Settings
- 74 Scale Indicator Programming
- 75 Menu System Selection
- 75 Main Menu System
- 75 Set Display Backlight
- 75 Set Weighing Units
- 75 Adjust Average Rate
- 76 Set Auto Power Off for Scale Indicator
- 76 Set Hold Enable for Scale Indicator
- 76 Set RS232 Port Baud Rate
- 76 Calibration Menu System
- 76 Set Radio Enable
- 76 Set Radio Channel
- 76 Set Radio Channel Network ID
- 77 Set Radio Channel Encryption Key
- 77 Reset Radio to Default Settings
- 77 Set for Weigh Unit Changeable in Main Menu
- 77 Set Auto Zero Tracking
- 77 Set Graduation Size
- 79 Notes
- 89 Company Statements
- 89 Accuracy
- 89 To the Purchaser
- 89 Warranty Manufacture
- 90 Liability for Delays
- 90 Contact Information
- 91 Technical Data
- 93 Operation
- 94 Pre-Operation Checks
- 94 Track Break-in
- 94 Track Tension
- 95 Track Alignment
- 96 Maximizing Tread Life
- 97 Maintenance
- 98 Daily
- 98 Track Maintenance
- 99 Periodic Storage
- 99 Long Term Storage
- 100 Adjusting Track Tension
- 101 Adjusting Alignment
- 103 Notes