ASSEMBLY. Brinly-Hardy BS36BH, BS-26BH, BS-36BH, BS26BH

ASSEMBLY

Figure 1.

INSTALL HOPPER SUPPORT

TO THE HOPPER

1a. Install six 1/4 x 1-3/4 in. hex bolts (4), and 1/4 in. thrust washer (3) through top of hopper (2) and through support frame (1), as shown.

1b. Secure bottom of bolt with 1/4 in. locknut (5). To avoid damage to plastic, do not overtighten hardware.

3

Flat Washer (Nylon), 1/4”

Qty. 6

5

Lock Nut, Nylon, 1/4””

Qty. 6

4

Bolt Hex, 1/4”x1-3/4”

Qty. 6

Figure 2.

ATTACH TOW TUBE

2a. Attach Tow Tube (28) to the Hopper

Support (1)1b. Secure using two

5/16”x2-3/4” Hex Bolts (27) and two

5/16”-18 Hex Nuts (26).

5

4

3

1

1

26

28

2

27

27

Bolt Hex, 5/16”x2-1/4”

Qty. 2

26

Hex Nut 5/16”

Qty. 2

L-1884E

7.

ASSEMBLY

Figure 3.

ASSEMBLY FAN TO TRANSMISSION

3a. Slide the Fan Driver (24) and Fan (25) on to the shaft of the Transmission

Assembly (21) until both reach the Pin

Spring (23)

Note: This is for pre-assembly only. Final adjustment of the fan is made later.

25

24

23

24

Fan Driver

Qty. 1

21

8.

L-1884E

ASSEMBLY

Figure 4.

INSTALL TRANSMISSION & AXLE

4a. Maneuver the transmission assembly (21) shaft into the center hole of the Hopper

Assembly (2). Ensure that the slot of the transmission brace rests on top of the two tow tube hex nuts previously installed in

Figure 2, as shown.

Note: Failure to install the transmission bracket correctly may void the warranty.

4b. Insert Axle (6) through both

Hopper Support (1) square openings and through center of transmission assembly (21), as shown.

Note: The axle needs to be installed as shown in order to engage the transmission assembly.

4c. Rotate the axle to line up the hole with the hole in Transmission assembly hub and insert

Hairpin Cotter (40)

4d. Secure the transmission brace by attaching two 5/16” Flat

Washers (32) and two Nylon

Lock Nuts (15), then tighten.

6

1

21

BACK

2

Axle only goes on one way

A

1

Insert Hairpin Cotter

(40)

A

Install Axle - “A” is equal lengths on both sides.

15

Lock Nut, Nylon 5/16”

Qty. 2

32

Flat Washer 5/16”

Qty. 2

32

15

40

Hairpin Cotter

Qty. 1

L-1884E

9.

ASSEMBLY

Figure 5-1. INSTALL WHEELS (METAL)

Note: The unit will be shiped with one of two types of wheels. Determine whether the wheels have metal or composite (plastic) rims. If the rim is metal, proceed to step

5a. If the rim is plastic, proceed to step

5c.

5a. Attach each Wheel (9) to the Axle (6) using hardware in the following order:

• One Axle Bearing (7)

• One or two Flat Washer 5/8” (8) - use one or two as needed.

• One Metal-Rimmed Wheel (9)

• One Flat Washer 5/8” (8)

• One Snapping E-Ring (10)

5b . Secure Axle to the right wheel by inserting Hairpin Cotter (22) through the wheel hub and axle. Proceed to step 6a.

Note: The axle may need to be turned in order to line up the hole in the axle with the hole through the wheel hub.

Apply grease to axle and wheel bearings

9 1

8

6

RIGHT

WHEEL

22

10 8 RIGHT

WHEEL

7

7

Add or delete Flat

Washer (8) to reduce Axle side to side movement.

22

1

9

8

9

LEFT

WHEEL

8 10

1

10 8 8 7

6

LEFT

WHEEL

9

22

Hairpin Cotter

Qty. 1

6

7 8 8 10

15

Axle Bearing

Qty. 2

8

Flat Washer 5/8”

Qty. 6

10

Snap Ring E-Type

Qty. 2

10.

L-1884E

Figure 5-2. INSTALL COMPOSITE WHEELS (PLASTIC)

5c.Attach each Wheel (9) to the Axle (6) using hardware in the following order:

• One Axle Bearing (7)

• One Flat Washer 5/8” (8)

• One Spacer (42)

• One or two Flat Washer 5/8” (8) - use 1 or two as needed.

• One Composite Wheel (9)

• One Flat Washer 5/8” (8)

• One Snapping E-Ring (10)

5d. Secure Axle to the left wheel by inserting Hairpin Cotter (22) through the wheel hub and axle.

Note: The axle may need to be turned in order to line up the hole in the axle with the hole through the wheel hub.

Apply grease to axle and wheel bearings

42

1

6

8

RIGHT WHEEL

10

1

8 RIGHT

WHEEL

9

42

7

7

Add or delete Flat

Washer (8) to reduce Axle side to side movement.

8

9

8 10

42

LEFT

WHEEL

22

10 8

1

22

42

6

7 8

8 7

6

LEFT WHEEL

9

42

Spacer

Qty. 2

8 10

15

Axle Bearing

Qty. 2

22

Hairpin Cotter

Qty. 1

8

Flat Washer 5/8”

Qty. 6

10

Snap Ring E-Type

Qty. 2

L-1884E

11.

Figure 6.

FAN ADJUSTMENT

6a. Adjust fan upwards on shaft as close as possible to the bottom of the hopper without touching during operation.

Note: The fan and fan driver normally rests on the spring pin, but may be adjusted upward approximately 1/8 of and inch.

ASSEMBLY

If neccesary, adjust fan upwards on shaft as close as possible to the bottom of the hopper without touching during operation.

12.

L-1884E

ASSEMBLY

Figure 7.

INSTALL AGITATOR

7a. Place O-Ring (20) over transmission shaft. Slide down to hopper bottom to create seal.

7b. Slide Agitator Spring (20) over transmission shaft.

7c. Insert Cotter Pin (18) through hole at top of transmission shaft. Flair ends to keep in place, as shown.

18

Cotter Pin, 1/8”x1”

Qty. 1

19

Agitator Spring

Qty. 1

19

20

18

19

18

20

O-Ring 3/8”

Qty. 1

20

L-1884E

13.

Figure 8.

INSTALL CLEVIS

8a. Attach the upper and lower Clevis (17) halves to the Tow Tube (28). Secure with two 5/16”x2” Carriage Bolts (14) and two

5/16” Nylon Hex Nuts (15), as shown.

8b. Insert 1/2”X2-1/2” Hitch Pin in to Clevis and secure using Hairpin Cotter (16), as shown.

ASSEMBLY

13

Hitch Pin 1/2” x2-1/2”

Qty. 1

16

Hairpin Cotter 1/8”

Qty. 1

14

Carriage Bolt 5/16”x2”

Qty. 2

14

28

15

Nylon Lock Nut 5/16”

Qty. 2

13

17

16

15

14.

L-1884E

ASSEMBLY

Figure 9.

ASSEMBLE GAGE PLATE

9a. Insert Stop Handle (31) through slot opening at the top of the Gauge Plate

(11).

9b. Insert the ‘S’ shaped end of Link Rod

(12) through the upper hole of the

Flow Control Handle (31).

9c. Assemble Flow Control (31) to Gage

Plate (11) as shown, using hardware provided:

• One 5/16”x2-3/4” Hex Bolt (36)

• Two 5/16” Flat Washers (32)

• One Latch Spacer (35)

• Two Special Washers (33)

• One Spring (34)

• One 5/1/6” Hex Nut (15)

Note: See graphic inset below for hardware orientation.

9d. Attach Handle Stop (30) and Knob

(29) as shown, using hardware provided:

• One 5/16”x3/4” Carriage Bolt (41

• One Crvd Washer. (39).

9e. Slide Flat Grip (37) on end of Flow control Handle (31).

15

Hex Nut 5/16”

Qty. 1

31

32

Washer 5/16”

Qty. 2

12

41

39

12

15

32

31

32

12

34 32 34

Washer Special

Qty. 2

31

37

11

30

34

33

35

12

32

36

29

11

15

35

Spacer, Latch

Qty. 1

33 35 35 34

Spring

Qty. 1

36

5/16”x2-1/4” Hex Bolt

Qty. 1

39

Washer Crvd

Qty. 1

29

Knob 4-Prong

Qty. 1

L-1884E

15.

ASSEMBLY

Figure 10a. ATTACH GAGE PLATE TO SPREADER

10a. Rotate assembled Gage

Plate (11) approximately 90° clockwise and insert formed end of the of the Link Rod

(12) in to the hole provide on the Hopper (10) control plate, as shown.

10b. Rotate Gage Plate counterclockwise until the handle is oriented upward and the bottom of the Gage Plate is over the Tow Tube (28).

10

12

11

16.

L-1884E

ASSEMBLY

Figure 10b. ATTACH GAGE PLATE TO SPREADER

10c. Attach the Gage Plate to the Tow

Tube (28) as shown, using hardware provided: Do tighten the hex nuts until after calibrating the gage plate.

• Two 5/16”x2-3/4” Hex Bolt (36)

• four 5/16” Flat Washers (32).

• Four Pivot Bushings (38).

• Two 5/1/6” Hex Nuts (15).

Note: See graphic inset below for hardware orientation.

32

28

32

15 38 36

32

15

38

32

38

28

32

32

36

32

Washer, 5/16”

Qty. 4

38

Bushing, Pivot

Qty. 4

15

Hex Nut 5/16”

Qty. 2

36

5/16”x2-3/4” Hex Bolt

Qty. 2

L-1884E

17.