About your projector. Panasonic PT-FRQ60BU7, PT-FRQ60WU7

Add to my manuals
221 Pages

advertisement

About your projector. Panasonic PT-FRQ60BU7, PT-FRQ60WU7 | Manualzz

Chapter 1   Preparation — About your projector

About your projector

Remote control

Front Top

3

4

1

2

5

6

11

4

12

13

Bottom

7

8

9

10

14

15

16

17

18

19

20

21 23

22

1 Power < v

/ b

> button

( v

: Standby, b

: Power on)

Sets the projector to the state where the projector is turned off (standby mode) when the <MAIN POWER> switch on the projector is set to <ON> and in projection mode.

Sets the projector to projection mode when the power is switched off (standby mode).

2 Remote control indicator

Blinks if any button in the remote control is pressed.

3 <MENU> button/<RETURN> button/<ENTER> button/ asqw buttons

Used to navigate through the menu screen. ( x

page 63) asqw

buttons are also used to enter the password in

[SECURITY] or enter characters.

4 <VOL-> button/<VOL+> button

Adjusts the volume of audio output. ( x

page 57)

5 <DEFAULT> button

Resets the content of the sub-menu to the factory default.

( x

page 64)

6 Input selection buttons ( <HDMI 1>, <HDMI 2>, <DIGITAL

LINK>, <COMPUTER>)

Switches the input signal to project. ( x

page 52)

7 Number (<0> - <9>) buttons

Used for entering an ID number or a password in a multiple projector environment.

8 <ON SCREEN> button

Switches the on-screen display function on (display) or off (hide).

( x

page 57)

9 <ID ALL> button

Used to simultaneously control all the projectors with a single remote control in a multiple projector environment. ( x

page 31)

10 <ECO> button

Displays the setting screen relating to ECO management.

( x

pages 60, 106)

11 <AUTO SETUP> button

Automatically adjusts the image display position and signal level while projecting the image.

[PROGRESS] is displayed while in automatic adjustment.

( x

page 57)

12 <FUNCTION> button

Assigns a frequently used operation as a shortcut button.

( x

page 59)

13 <CEC> button

Displays the HDMI-CEC operation screen. ( x

page 125)

14 <TEST PATTERN> button

Displays the test pattern. ( x

page 59)

15 <ID SET> button

Sets the ID number of the remote control in a multiple projector environment. ( x

page 31)

16 <GEOMETRY> button

Used to correct the distortion of the projected image. ( x

pages

58, 78)

17 <FREEZE> button

Used when pausing the image and turning off the audio.

( x

page 57)

18 <STATUS> button

Displays the projector information.

19 <SHUTTER> button

Used when temporarily turning off the image and audio.

( x

page 56)

20 <MUTE> button

Used when temporarily turning off the audio. ( x

page 56)

21 <ASPECT> button

Switches the aspect ratio of the image. ( x

page 59)

22 Remote control signal transmitter

23 (Not available with this projector)

ENGLISH - 27

Chapter 1   Preparation — About your projector

Attention f

Do not drop the remote control.

f

Avoid contact with liquids or moisture.

f

Do not attempt to modify or disassemble the remote control.

f

Observe the following instructions that are indicated on the caution label at the back of the remote control: g

Do not use old battery with new one.

g

Do not use batteries other than the type specified.

g

Be sure the batteries are inserted properly.

For other instructions, read the instructions related to batteries that are described in “Read this first!”.

Caution label at the back of the remote control

Note f

When operating the remote control by directly pointing at the remote control signal receiver of the projector, operate the remote control within a distance approximately 30 m (98'5") from the remote control signal receiver. The remote control can control at angles of up to ±30° vertically and horizontally, but the effective control range may be reduced.

f

If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not operate properly.

f

The signal will be reflected off the screen. However, the operating range may be limited from light reflection loss due to the screen material.

f

If the remote control signal receiver directly receives strong light, such as fluorescent light, the remote control may not operate properly. Use it in a place distant from the light source.

f

The power indicator <ON (G)/STANDBY (R)> will blink if the projector receives a remote control signal.

Projector body

Front

1 2 3 4 5 6

Side

11 8 8 8

7

Rear

8

9

7

9 10

12

13 14 15

16 17

28 - ENGLISH

Top

Chapter 1   Preparation — About your projector

Bottom

8 18

Projection direction

1 Remote control signal receiver (front)

2 Power indicator <ON (G)/STANDBY (R)>

Indicates the status of the power.

3 Light source indicator <LIGHT>

Indicates the status of the light source.

4 Temperature indicator <TEMP>

Indicates the internal temperature status.

5 Projection lens

6 Lens shift lever

Adjusts the projection position.

7 Adjustable feet

Adjusts the projection angle.

8 Intake vent

9 Exhaust vent

10 Remote control signal receiver (rear)

Attention f

Do not block the intake and exhaust vents of the projector.

r

Control panel

1

11 Focus ring

Adjusts the focus.

12 Zoom ring

Adjusts the zoom.

13 Control panel ( x

page 29)

14 Connecting terminals ( x

page 30)

15 Security slot

This security slot is compatible with the Kensington security cables.

16 <MAIN POWER> switch

Turns on/off the main power.

17 <AC IN> terminal

Connect the supplied power cord.

18 Burglar hook port

Attaches a burglar prevention cable, etc.

3

2

1 Power < v

/ b

> button

( v

: Standby, b

: Power on)

Sets the projector to the state where the projector is turned off (standby mode) when the <MAIN POWER> switch on the projector is set to <ON> and in projection mode.

Sets the projector to projection mode when the power is switched off (standby mode).

2 <MENU> button/<RETURN> button/<ENTER> button/ asqw buttons

Used to navigate through the menu screen.

Also used to enter a password in the [SECURITY] menu or enter characters.

3 <INPUT SELECT> button

Switches the input signal to project. ( x

page 53)

ENGLISH - 29

Chapter 1   Preparation — About your projector r

Connecting terminals

1 2 3 4 5 6 7 8 9

1 <AUDIO IN> terminal

This is a terminal to input audio signal.

2 <AUDIO OUT> terminal

This is a terminal to output the audio signal input to the projector.

3 <COMPUTER IN> terminal

This is a terminal to input the RGB signal or YC

B

C

R

/YP

B

P

R

signal.

4 <MONITOR OUT> terminal

This terminal can output the RGB signal or YC

B

C

R

/YP

B

P

R

signal input from the <COMPUTER IN> terminal to an external device.

5 <HDMI IN 1> terminal/<HDMI IN 2> terminal

This is a terminal to input the HDMI signal.

6 <SERIAL IN> terminal

This is the RS-232C compatible terminal to externally control the projector by connecting a computer.

7 <USB (DC OUT)> terminal

This is a terminal to connect the USB memory when using the data cloning function or firmware update function. ( x

pages 179,

185)

This is also the terminal to connect the optional Wireless Module

(Model No.: AJ-WM50 Series) when the projector is connected via wireless LAN. ( x

page 151)

This terminal is also used for power supply.

(DC 5 V, maximum 2 A)

8 <DIGITAL LINK/LAN> terminal

This is a terminal to connect a device that transmits image signal or audio signal via the LAN terminal. Also, this is the LAN terminal to connect to the network.

9 <LAN> terminal

This is the LAN terminal to connect to the network.

Attention f

When a LAN cable is directly connected to the projector, the network connection must be made indoors.

f

To transmit the Ethernet and serial control signals using the <DIGITAL LINK/LAN> terminal, set the [NETWORK] menu → [ETHERNET

TYPE] to [DIGITAL LINK] or [LAN & DIGITAL LINK].

f

To transmit the Ethernet signal using the <LAN> terminal, set the [NETWORK] menu → [ETHERNET TYPE] to [LAN] or [LAN & DIGITAL

LINK].

f

The <DIGITAL LINK/LAN> terminal and the <LAN> terminal are connected inside of the projector when the [NETWORK] menu → [ETHERNET

TYPE] is set to [LAN & DIGITAL LINK]. Do not directly connect the <DIGITAL LINK/LAN> terminal and the <LAN> terminal using LAN cable.

Construct the system so that it is not connected to the same network via the peripherals such as the switching hub or the twisted-pair-cable transmitter.

f

When the [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] is set to [NORMAL], the <USB (DC OUT)> terminal can supply power even in standby state. If set to [ECO], the <USB (DC OUT)> terminal can not supply power in standby state.

f

When an external device exceeding the rating (DC 5 V, maximum 2 A) is connected to the <USB (DC OUT)> terminal, an error is detected and the power supply will be stopped. At this time, disconnect the external device, cut off the power of the projector and then reconnect the power plug to the outlet.

30 - ENGLISH

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents