Switching on/off the projector. Panasonic PT-FRQ60BU7, PT-FRQ60WU7

Add to my manuals
221 Pages

advertisement

Switching on/off the projector. Panasonic PT-FRQ60BU7, PT-FRQ60WU7 | Manualzz

Chapter 3   Basic Operations — Switching on/off the projector

Switching on/off the projector

Connecting the power cord

Make sure that the supplied power cord is securely fixed to the <AC IN> terminal of the projector to prevent it from being removed easily.

Confirm that the <MAIN POWER> switch is on the <OFF> side before connecting the supplied power cord to the projector.

Use the power cord matching with the power supply voltage and the shape of the outlet.

For details of power cord handling, refer to “Read this first!” ( x

page 5).

How to attach the power cord

1) Check the shapes of the <AC IN> terminal on the side of the projector and the power cord connector, and insert the connector completely in the correct direction (until you hear the side tabs click in place).

How to remove the power cord

1) Confirm that the <MAIN POWER> switch on the side of the projector is on the <OFF> side, and remove the power plug from the outlet.

2) Remove the power cord connector from the <AC IN> terminal of the projector while pressing the side tabs.

Power indicator

Indicate the status of the power. Check the status of the power indicator <ON (G)/STANDBY (R)> before operating the projector.

Power indicator <ON (G)/STANDBY (R)>

42 - ENGLISH

Chapter 3   Basic Operations — Switching on/off the projector

Indicator status

Off

Red

Green

Orange

Lit

Blinking

Lit

Lit

Projector status

The main power is switched off.

The power is switched off. (standby mode)

Projection will start when the power < v

/ b

> button is pressed.

f

The setting of the projector is as follows.

g

The [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [QUICK STARTUP] is set to [OFF] g

The [PROJECTOR SETUP] menu → [AUDIO SETTING] → [IN STANDBY MODE] is set to [OFF] f

The projector may not operate when the light source indicator <LIGHT> or the temperature indicator

<TEMP> is blinking. ( x

page 193)

The power is switched off. (standby mode)

Projection will start when the power < v

/ b

> button is pressed.

f

The projector is in one of the following states.

g

The [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [QUICK STARTUP] is set to [ON] g

The [PROJECTOR SETUP] menu → [AUDIO SETTING] → [IN STANDBY MODE] is set to [ON] g

The output image corresponding to the projected image from the projector is being checked by the web control function. For details, refer to “[Remote preview lite] page” ( x

page 157).

f

The indicator will change to a red light when the specified time has elapsed after the projector enters the standby mode if the projector is set as following. However, the indicator will not change to a red light while the output image is being checked by the web control function.

The specified time is a time set in the [PROJECTOR SETUP] menu → [ECO MANAGEMENT] →

[QUICK STARTUP] → [VALID PERIOD].

g

The [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [QUICK STARTUP] is set to [ON] g

The [PROJECTOR SETUP] menu → [AUDIO SETTING] → [IN STANDBY MODE] is set to [OFF] f

The projector may not operate when the light source indicator <LIGHT> or the temperature indicator

<TEMP> is blinking. ( x

page 193)

Projecting.

The projector is preparing to switch off the projector.

The power is switched off after a while. (Changes to the standby mode.)

Note f

While the power indicator <ON (G)/STANDBY (R)> lights orange, the fan is running to cool the projector.

f

For approximately five seconds after the projector is turned off, the indicator does not light up even if the power is turned on. Turn on the power again after the power indicator <ON (G)/STANDBY (R)> lights/blinks red.

f

The projector consumes power even in standby mode (power indicator <ON (G)/STANDBY (R)> lights/blinks red). Refer to “Maximum power consumption” ( x

page 213) for the power consumption.

f

The power indicator <ON (G)/STANDBY (R)> will blink if the projector receives a remote control signal.

f

The power indicator <ON (G)/STANDBY (R)> will blink green slowly while the shutter function is in use (shutter: closed), or while the function of the [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [POWER MANAGEMENT] → [NO SIGNAL LIGHTS-OUT] is operating and the light source is turned off.

Switching on the projector

4)

4)

3) 1) 2)

1) Connect the power cord to the projector.

2) Connect the power plug to an outlet.

3) Press the <ON> side of the <MAIN POWER> switch to turn on the power.

f The power indicator <ON (G)/STANDBY (R)> lights/blinks red, and the projector enters the standby mode.

ENGLISH - 43

Chapter 3   Basic Operations — Switching on/off the projector

4) Press the power < v

/ b

> button.

f

The power indicator <ON (G)/STANDBY (R)> lights green and the image is soon projected on the screen.

Note f

A warm-up period of up to approximately five minutes may be necessary until an image is displayed when the projector is switched on at around 0 °C (32 °F).

The temperature indicator <TEMP> lights red during the warm-up period. When the warm-up is completed, the temperature indicator

<TEMP> turns off and the projection starts. Refer to “When an indicator lights up” ( x

page 193) for the indicator status display.

f

If the operating environment temperature is low and warm-up takes more than five minutes, the projector will judge that a problem has occurred and the power will automatically be set to standby mode. In such case, increase the operating environment temperature to 0 °C

(32 °F) or higher, turn off the main power, and then turn on the power again.

f

When the [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] is set to [ECO], it takes longer for the projection to start after the power is turned on, compared to when set to [NORMAL].

f

When the [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [QUICK STARTUP] is set to [ON], and the power is turned on before the specified time elapses after the projector enters the standby mode, an image will be projected approximately one second after the power is turned on.

The specified time is a time set in the [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [QUICK STARTUP] → [VALID PERIOD].

f

If the power is turned on while the output image is being checked by the web control function, the image will be projected approximately one second after the power is turned on.

f

When the power is turned on or an input signal is switched, you may here a high-frequency driving sound. This is not a malfunction.

f

If the power was turned off at the previous use by pressing the <OFF> side of the <MAIN POWER> switch or by using the breaker directly while projecting, the power indicator <ON (G)/STANDBY (R)> lights green and an image is projected after a while when the power is turned on by pressing the <ON> side of the <MAIN POWER> switch or by turning the breaker on with the power plug connected to the outlet. This applies only when the [PROJECTOR SETUP] menu → [INITIAL STARTUP] is set to [LAST MEMORY].

When the initial setting screen is displayed

When the projector is switched on for the first time after purchase, as well as when the [PROJECTOR SETUP] menu → [INITIALIZE] → [FACTORY RESET] is executed, the [INITIAL SETTING] screen is displayed followed by the [ADMINISTRATOR ACCOUNT] screen after projection starts. When the [PROJECTOR SETUP] menu →

[INITIALIZE] → [NETWORK/E-MAIL ONLY] is executed, the [ADMINISTRATOR ACCOUNT] screen is displayed after projection starts. Set them according to the circumstances.

In other occasions, you can change the settings by menu operations.

If you press the <MENU> button while the [INITIAL SETTING] screen is displayed, you can go back to the previous screen.

Same operation is available by pressing the <RETURN> button.

Note f It may be necessary to adjust with the focus ring and the zoom ring on the lens section of the projector to clearly display the menu screen when using the projector for the first time.

Refer to “Adjusting the image” ( x

page 53) for details.

Initial setting (display language)

Select the language to show on the screen.

After completed the initial setting, you can change the display language from the [DISPLAY LANGUAGE] menu.

1) Press asqw

to select the display language.

INITIAL SETTING 1/7

Қазақша

ENTER

SELECT

SET

2) Press the <ENTER> button to proceed to the initial setting.

44 - ENGLISH

Chapter 3   Basic Operations — Switching on/off the projector

Initial setting (operation setting)

Set the items for the operating method depending on the projector’s application and duration of usage.

After completed the initial setting, you can change the settings of each item from the [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [OPERATING MODE]. If you change the settings while using the projector, the duration until the brightness decreases to half may shorten or the brightness may decrease.

This initial setting (operation setting) is prepared to complete the settings simply at once during the installation when the operation of the projector is predetermined. This cannot set all the items regarding the operation setting.

When the detailed setting is required or setting change is required, ask the person responsible for this projector

(such as a person in charge of equipment or operation).

INITIAL SETTING

OPERATING MODE

LIGHT OUTPUT

Set the way to use the projector.

For details, please refer to the operating instructions "When the initial setting screen is displayed".

NORMAL

100.0%

2/7

ENTER

CHANGE

SET

Note f

For the relationship between the brightness and the runtime, refer to “Relationship between brightness and runtime” ( x

page 46).

1) Press as

to select [OPERATING MODE].

2) Press qw

to switch the item.

f

The items will switch each time you press the button.

[NORMAL]

[ECO]

[QUIET]

Set this item to prioritize the brightness. [LIGHT OUTPUT] is 100 %, and the estimated runtime is approximately 20 000 hours *1 .

The brightness will decrease compared to [NORMAL], but set this item to prioritize the life of the light source. [LIGHT OUTPUT] is 80 %, and the estimated runtime is approximately 24 000 hours *1 .

The brightness will decrease compared to [NORMAL], but set this item to prioritize the operation with low noise. [LIGHT OUTPUT] is 80 %, and the estimated runtime is approximately 20 000 hours *1 .

Set [LIGHT OUTPUT] as desired.

[USER]

*1 Estimated runtime is the time until the brightness decreases to approximately half of the time of delivery when the projector is used with the [PICTURE] menu → [DYNAMIC CONTRAST] set to [2] and under environment of 0.15 mg/m

The value of runtime is just an estimate, and is not the warranty period.

3 dust. f

Proceed to Step 3) when [USER] is selected.

3) Press as

to select [LIGHT OUTPUT].

4) Press qw

to adjust.

Operation

Press w

.

Press q

.

Brightness

The screen becomes brighter.

The screen becomes darker.

Adjustment

Runtime

The runtime becomes shorter.

The runtime becomes longer.

Range of adjustment

20 % - 100 %

5) Press the <ENTER> button to proceed to the initial setting.

ENGLISH - 45

Chapter 3   Basic Operations — Switching on/off the projector

Relationship between brightness and runtime

The projector can be operated with arbitrary brightness and runtime by setting [LIGHT OUTPUT] to desired setting.

The relationship between the [LIGHT OUTPUT] setting, brightness, and the estimated runtime is as follows. Make the initial setting (operation setting) depending on the desired brightness of the projected image and runtime.

The values of the brightness and the runtime are just an estimate, and the graph indicating the relationship is just an example. Also, these do not indicate the warranty period.

[LIGHT OUTPUT] (%)

100.0

69.5

29.0

PT-FRQ60

6 000

4 200

1 700

Brightness (lm)

PT-FRQ50

5 200

3 600

1 500

Estimated runtime

20 000

24 000

27 000

*1 (hour)

*1 Estimated runtime is the time until the brightness decreases to approximately half of the time of delivery when the projector is used with the [PICTURE] menu → [DYNAMIC CONTRAST] set to [2] and under environment of 0.15 mg/m 3 dust.

100,0

90,0

80,0

70,0

60,0

50,0

40,0

30,0

20,0

20 000 21 000

5 200

3 600

/

/

6 000

4 200

1 500 / 1 700

22 000 23 000 24 000 25 000 26 000 27 000

Estimated runtime (hours)

Note f

Under influences of characteristics of each light source, conditions of use, installation environment, etc., the runtime may be shorter than the estimation.

f

If the runtime exceeds 20 000 hours, replacement of the components inside the projector may be required. Consult your dealer for details.

f

After completed the initial setting, the wider the combination of luminance and runtime becomes by setting the [PROJECTOR SETUP] menu

→ [BRIGHTNESS CONTROL] → [BRIGHTNESS CONTROL SETUP] → [CONSTANT MODE] to [AUTO] or [PC]. Refer to the [PROJECTOR

SETUP] menu → [BRIGHTNESS CONTROL] for details.

Initial setting (installation setting)

Set [FRONT/REAR] and [FLOOR/CEILING] in [PROJECTION METHOD] depending on the installation mode.

Refer to “Installation mode” ( x

page 33) for details.

After completed the initial setting, you can change the setting from the [PROJECTOR SETUP] menu →

[PROJECTION METHOD].

1) Press qw

to switch the setting.

INITIAL SETTING

PROJECTION METHOD

FRONT/REAR

FLOOR/CEILING

Change the projection method

(FRONT/REAR, FLOOR/CEILING) if the screen display is upside down or inverted.

FRONT

AUTO

3/7

ENTER

MENU SELECT

SET

CHANGE

2) Press the <ENTER> button to proceed to the initial setting.

46 - ENGLISH

Chapter 3   Basic Operations — Switching on/off the projector

Initial setting (standby mode)

Set the operation mode during standby. The factory default setting is [NORMAL], which allows you to use the network function during standby. To keep power consumption low during standby, set this item to [ECO].

After completed the initial setting, you can change the setting from the [PROJECTOR SETUP] menu → [ECO

MANAGEMENT] → [STANDBY MODE].

1) Press qw

to switch the setting.

INITIAL SETTING

STANDBY MODE NORMAL

When set to ECO, network functions and some RS-232C commands are not available during standby.

4/7

ENTER

CHANGE

SET

2) Press the <ENTER> button to proceed to the initial setting.

Initial setting (screen setting)

Set the screen format (aspect ratio) and display position of the image.

After completed the initial setting, you can change the settings of each item from the [DISPLAY OPTION] menu →

[SCREEN SETTING].

1) Press qw

to switch the setting.

f

The setting will change each time you press the button.

f

Proceed to Step 4) when [16:9] is selected.

INITIAL SETTING

SCREEN FORMAT

Set as necessary for the screen in use.

16:9

5/7

ENTER

CHANGE

SET

2) Press as

to select [SCREEN POSITION].

3) Press qw

to adjust.

INITIAL SETTING

SCREEN FORMAT

SCREEN POSITION

Set as necessary for the screen in use.

16:10

0

5/7

ENTER

MENU SELECT

SET

CHANGE

ENGLISH - 47

Chapter 3   Basic Operations — Switching on/off the projector

4) Press the <ENTER> button to proceed to the initial setting.

Initial setting (time zone)

Set [TIME ZONE] in accordance with the country or region where you use the projector.

After completed the initial setting, you can change the setting from the [PROJECTOR SETUP] menu → [DATE

AND TIME]. The current settings are displayed in [LOCAL DATE] and [LOCAL TIME].

1) Press qw

to switch the setting.

INITIAL SETTING

TIME ZONE

LOCAL DATE

+09:00

20XX/01/01

LOCAL TIME 12 : 34 : 56

Please set up a time zone according to the area of your country or region.

6/7

ENTER

CHANGE

SET

2) Press the <ENTER> button to proceed to the initial setting.

Note f

In the factory default setting, the time zone of the projector is set to +09:00 (Japan and Korea Standard Time). Change the setting of the

[PROJECTOR SETUP] menu → [DATE AND TIME] → [TIME ZONE] to the time zone of the region where you use the projector.

Initial setting (date and time)

Set the local date and time. After completed the initial setting, you can change the setting from the [PROJECTOR

SETUP] menu → [DATE AND TIME].

To set the date and time automatically, refer to “Setting the date and time automatically” ( x page 117).

1) Press as

to select an item.

INITIAL SETTING

YEAR

MONTH

DAY

HOUR

MINUTE

SECOND

Please set the date and time of the built-in clock of the projector.

20XX

1

1

12

34

56

7/7

ENTER

MENU SELECT

SET

CHANGE

2) Press qw to switch the setting.

3) Press the <ENTER> button.

f Confirm the setting value and complete the initial setting.

48 - ENGLISH

Chapter 3   Basic Operations — Switching on/off the projector

When the administrator account setting screen is displayed

When the projector is switched on for the first time after purchase, as well as when the [PROJECTOR SETUP] menu →[INITIALIZE] → [FACTORY RESET] is executed, the [ADMINISTRATOR ACCOUNT] screen is displayed following the [INITIAL SETTING] screen after projection starts.

When the [PROJECTOR SETUP] menu → [INITIALIZE] → [NETWORK/E-MAIL ONLY] is executed, the

[ADMINISTRATOR ACCOUNT] screen is displayed after projection starts.

To use the network function of this projector, set the user name and password of the administrator account. You can also set it later from the [NETWORK] menu → [ADMINISTRATOR ACCOUNT].

ADMINISTRATOR ACCOUNT

PASSWORD POLICY

USER NAME

PASSWORD

PASSWORD CONFIRM

STORE dispadmin

Please set the user name and password.

if not set, could not use the Web Control function and for communication control via a LAN

(including Panasonic application software).

ENTER

MENU SELECT

SUB MENU

[PASSWORD POLICY]

Displays the policies about the password for the administrator account.

1) Press as

to select [PASSWORD POLICY], and press the <ENTER> button.

f

The [PASSWORD POLICY] screen is displayed.

f

Pressing the <MENU> button can return to the [ADMINISTRATOR ACCOUNT] screen.

PASSWORD POLICY

Reusing passwords is not recommended.

Password cannot be blank.

A password consisting of at least eight half-width characters and contaning characters of at least three of the following four types is recommended.

Uppercase letters

Lowercase letters

Digits

Symbols(~!@#$%^&*()_+\|}{][<>.,/?`)

MENU

RETURN

Setting the administrator account

Set the user name and password of the administrator account.

1) Press as

to select [USER NAME], and press the <ENTER> button.

f

The [USER NAME] screen is displayed.

f

The factory default setting of user name is "dispadmin".

2) Press asqw

to select a character, and press the <ENTER> button.

f

Up to 16 characters can be entered.

3) After entering the user name, press asqw

to select [OK], and press the <ENTER> button.

f

The [ADMINISTRATOR ACCOUNT] screen is displayed.

4) Press as to select [PASSWORD], and press the <ENTER> button.

f

The [PASSWORD] screen is displayed.

5) Press asqw

to select a character, and press the <ENTER> button.

f

Up to 16 characters can be entered.

f

The password cannot be blank.

ENGLISH - 49

Chapter 3   Basic Operations — Switching on/off the projector

6) After entering the password, press asqw

to select [OK], and press the <ENTER> button.

f

The [ADMINISTRATOR ACCOUNT] screen is displayed.

7) Press as to select [PASSWORD CONFIRM], and press the <ENTER> button.

f

The [PASSWORD CONFIRM] screen is displayed.

8) Enter the password entered in Step 5).

9) After entering the password, press asqw

to select [OK], and press the <ENTER> button.

f The [ADMINISTRATOR ACCOUNT] screen is displayed.

10) Press as

to select [STORE], and press the <ENTER> button.

f

The confirmation screen is displayed.

11) Press qw

to select [OK], and press the <ENTER> button.

Note f

For restrictions on character strings that can be set for password, refer to [PASSWORD POLICY] ( x

page 49) .

f

By pressing the <MENU> button while the [ADMINISTRATOR ACCOUNT] screen is displayed, you can proceed to the next operation without setting an administrator account password, but the network function of this projector cannot be used. To use the web control function or the communication control (including operation with application software) via LAN, set a password. f

If you press the <MENU> button while the [ADMINISTRATOR ACCOUNT] screen is displayed, the [ADMINISTRATOR ACCOUNT] screen will not be displayed the next time the power is turned on. To use the network function, set a password in the [NETWORK] menu →

[ADMINISTRATOR ACCOUNT].

f

The user name and password of the administrator account can also be changed on the "[Set up password] page (for administrator account)"

( x

page 176) of the web control screen.

f

The user name and password of the standard user account without administrator rights can be set on the "[Set up password] page (for administrator account)" ( x

page 176) of the web control screen.

Making adjustments and selections

It is recommended that images be projected continuously for at least 30 minutes before the focus is adjusted.

5)

2) 3)

6)

2)

3)

4)

1) 8)

7) 9)

1) Turn the focus ring to roughly adjust the focus of the projected image. ( x

page 53)

2) Change the setting of the [PROJECTOR SETUP] menu → [PROJECTION METHOD] depending on the installation mode. ( x

page 33) f

Refer to “Navigating through the menu” ( x

page 63) for the operation of the menu screen.

3) Select the input by pressing the input selection button on the remote control or the control panel.

f

The buttons that can be used on the remote control or the control panel are as follows.

Remote control:

<HDMI 1> button, <HDMI 2> button, <DIGITAL LINK> button, <COMPUTER> button

Control panel:

<INPUT SELECT> button f

For details of operation for input selection, refer to “Selecting the input signal” ( x

page 52).

4) Adjust the front, back and sideway tilt of the projector with the adjustable feet. ( x

page 54)

5) Adjust the position of the projected image by operating the lens shift lever.

50 - ENGLISH

Chapter 3   Basic Operations — Switching on/off the projector

6) If the input signal is the analog RGB signal or the HDMI signal, press the <AUTO SETUP> button.

7) Turn the zoom ring to adjust the size of the projected image to match the screen.

8) Adjust the focus again with the focus ring.

9) Adjust the zoom again with the zoom ring to adjust the size of the projected image to match the screen.

Note f

When the projector is switched on for the first time after purchase, or when the [PROJECTOR SETUP] menu → [INITIALIZE] → [FACTORY

RESET] is executed, the [INITIAL SETTING] screen is displayed after the projection starts, followed by the [ADMINISTRATOR ACCOUNT] screen. If the [PROJECTOR SETUP] menu → [INITIALIZE] → [NETWORK/E-MAIL ONLY] is executed, the [ADMINISTRATOR ACCOUNT] screen is displayed after the projection starts. For details, refer to “When the initial setting screen is displayed” ( x

page 44), “When the administrator account setting screen is displayed” ( x

page 49).

Switching off the projector

3)

1)

4)

1)

2)

2)

1) Press the power < v

/ b

> button.

f The [POWER OFF(STANDBY)] confirmation screen is displayed.

2) Press qw

to select [OK], and press the <ENTER> button.

(Or press the power < v

/ b

> button again.) f Projection of the image will stop, and the power indicator <ON (G)/STANDBY (R)> on the projector body lights orange. (The fan keeps running.)

3) Wait for a few seconds until the power indicator <ON (G)/STANDBY (R)> of the projector body lights/ blinks red.

4) Press the <OFF> side of the <MAIN POWER> switch to turn off the power.

Note f

For approximately five seconds after the projector is turned off, the indicator does not light up even if the power is turned on.

f

Even when the power < v

/ b

> button is pressed and the projector is switched off, the projector consumes power if the main power of the projector is on.

When the [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] is set to [ECO], use of some functions is restricted, but the power consumption during standby mode can be conserved.

f

While projecting, the power can be turned off by pressing the <OFF> side of the <MAIN POWER> switch, or by directly using the breaker under conditions where the <MAIN POWER> switch of the projector cannot be switched off/on easily such as while installing on the ceiling.

However, the settings or adjustments performed right before the power is turned off may not be reflected.

ENGLISH - 51

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents