Operating with the remote control. Panasonic PT-FRQ60BU7, PT-FRQ60WU7

Add to my manuals
221 Pages

advertisement

Operating with the remote control. Panasonic PT-FRQ60BU7, PT-FRQ60WU7 | Manualzz

Chapter 3   Basic Operations — Operating with the remote control

Operating with the remote control

Using the shutter function

If the projector is not used for a certain period of time during the meeting intermission, for example, it is possible to turn off the image and audio temporarily.

button

1) Press the <SHUTTER> button.

f

The image and audio disappear.

2) Press the <SHUTTER> button again.

f

The image and audio reappear.

Note f

The power indicator <ON (G)/STANDBY (R)> will blink green slowly while the shutter function is in use (shutter: closed).

f

The fade-in/fade-out time of the image can be set by the [DISPLAY OPTION] menu → [SHUTTER SETTING].

f

To output audio while the shutter function is in use (shutter: closed), set the [PROJECTOR SETUP] menu → [AUDIO SETTING]

( x

page 120) → [IN SHUTTER] to [ON].

f

The projector does not have a built-in speaker. Audio is output from the external audio system connected to the <AUDIO OUT> terminal.

f

The light source may be lit dimly due to warm up when the shutter function is used in the operating environment temperature of around 0 °C

(32 °F).

Using the mute function

Audio can be temporarily turned off.

button

1) Press the <MUTE> button.

f

The audio is muted.

2) Press the <MUTE> button again.

f

The audio is turned on.

56 - ENGLISH

Chapter 3   Basic Operations — Operating with the remote control

Adjusting the volume

Adjust the volume of audio output.

button

1) Press the <VOL-> button/<VOL+> button on the remote control.

<VOL+>

<VOL->

Increases the volume.

Decreases the volume.

Note f

This operation can be also performed using qw

on the control panel.

Using the freeze function

The projected image can be paused and audio can be turned off regardless of the playback of the external device.

button

1) Press the <FREEZE> button.

f

The image freezes and audio is muted.

2) Press the <FREEZE> button again.

f

Freezing of the image is canceled and audio is turned on.

Note f

[FREEZE] is displayed on the screen when video is paused.

f

When freezing of the moving image is canceled, the image may disappear or be disrupted temporarily.

Using the on-screen display function

Turn off the on-screen display function (no display) when you do not wish the viewers to see the on-screen display, such as the menu or the input terminal name.

button

1) Press the <ON SCREEN> button.

f The on-screen display disappears.

2) Press the <ON SCREEN> button again.

f The on-screen display appears.

Note f

If you press the <MENU> button on the control panel for at least three seconds while the on-screen display is off (hidden), the on-screen display is turned on.

Using the automatic setup function

The image position when the HDMI signal is input, or the resolution, clock phase, and image position when the analog RGB signal is input can be adjusted automatically. (Analog RGB signal is a signal structured with dots just like the computer signal.)

It is recommended to input an image with bright white borders at the edges and high-contrast black and white characters when the automatic adjustment is being performed.

ENGLISH - 57

Chapter 3   Basic Operations — Operating with the remote control

Avoid using images that include halftones or gradation, such as photographs and computer graphics.

button

1) Press the <AUTO SETUP> button.

f

[COMPLETE] is displayed when it has completed without any problem.

Note f

The clock phase may shift even if it has completed without any incident. In such a case, adjust the [POSITION] menu → [CLOCK PHASE]

( x

page 78).

f

If an image with blurred edges or a dark image is input, [INCOMPLETE] may appear or adjustment may not be performed properly even when [COMPLETE] appears. In such a case, adjust the following settings.

g

[ADVANCED MENU] menu → [INPUT RESOLUTION] ( x

page 85) g

[POSITION] menu → [CLOCK PHASE] ( x

page 78) g

[POSITION] menu → [SHIFT] ( x

page 76) f

Adjust special signals according to the [DISPLAY OPTION] menu → [AUTO SETUP] ( x

page 92).

f

Automatic adjustment may not be possible depending on the computer model.

f

Automatic adjustment may not be possible for the synchronization signal for composite sync or SYNC ON GREEN. f

Images may be disrupted for a few seconds during execution of the automatic setup, but it is not a malfunction.

f

Adjustment is required for each input signal.

f

Automatic setup can be canceled by pressing the <MENU> button while the automatic setup is being executed.

f

Even if a signal possible to perform the automatic setup is being input, it may not be able to adjust correctly if the automatic setup function is used while the moving image is being input. [INCOMPLETE] may be displayed, or the adjustment may not be completed correctly even if

[COMPLETE] is displayed.

Using the geometric adjustment function

You can correct various types of distortion in a projected image.

Unique image processing technology enables projection of a square image on a special screen shape.

The projected image can be made to look more natural by making topical correction as necessary.

button

1) Press the <GEOMETRY> button.

f

The [GEOMETRY] screen is displayed.

2) Press qw

to switch the item.

f

The items will switch each time you press the button.

[OFF]

[KEYSTONE]

Disables the geometric adjustment function.

Adjusts any trapezoidal distortion in the projected image.

[CORNER CORRECTION] Adjusts any distortion in the four corners of the projected image.

[CURVED CORRECTION] Adjusts any curved distortion in the projected image.

f

Proceed to Step 3) when anything other than [OFF] is selected.

3) Press the <ENTER> button.

f

The [GEOMETRY:KEYSTONE] screen, the [GEOMETRY:CORNER CORRECTION] screen, or the

[GEOMETRY:CURVED CORRECTION] screen is displayed.

Note f

Refer to the [POSITION] menu → [GEOMETRY] ( x

page 78) for details.

58 - ENGLISH

Chapter 3   Basic Operations — Operating with the remote control

Switching the image aspect ratio

Switch the image aspect ratio according to the input.

button

1) Press the <ASPECT> button.

f The setting will change each time you press the button.

Note f

Refer to the [POSITION] menu → [ASPECT] ( x

page 76) for details.

Using the function button

By assigning the following functions to the <FUNCTION> button, it can be used as a simplified shortcut button.

[SUB MEMORY], [SYSTEM SELECTOR], [DAYLIGHT VIEW], [FREEZE], [WAVEFORM MONITOR], [ASPECT],

[PROJECTION METHOD], [GEOMETRY], [OSD POSITION]

button

1) Press the <FUNCTION> button.

Note f

Assignment of the function is performed from the [PROJECTOR SETUP] menu → [FUNCTION BUTTON] ( x

page 119).

Displaying internal test pattern

The projector has eight types of internal test patterns to check the condition of the projector body. To display test patterns, perform the following steps.

button

1) Press the <TEST PATTERN> button.

2) Press qw

to select the test pattern.

Note f

Test patterns can also be displayed using the menu operation. Refer to “[TEST PATTERN] menu” ( x

page 129) for details.

f

Settings of position, size, and other factors will not be reflected in test patterns. Make sure to display the input signal before performing various adjustments.

Using the status function

Display the status of the projector.

button

1) Press the <STATUS> button.

f

The [STATUS] screen is displayed.

ENGLISH - 59

Chapter 3   Basic Operations — Operating with the remote control

STATUS

PROJECTOR TYPE

SERIAL NUMBER

PROJECTOR RUNTIME

PT-FRQ50

SN1234567

10h

LIGHT RUNTIME

CONTINUOUS LIGHTING TIME

MAIN/SUB VERSION

INTAKE AIR TEMP.

OPTICS MODULE TEMP.

EXHAUST AIR TEMP.

2h

1h 23m

1.00 / 1.00

25°C/77°F

29°C/84°F

LIGHT TEMP. 1

LIGHT TEMP. 2

SELF TEST

28°C/82°F

34°C/93°F

36°C/96°F

NO ERRORS

ENTER

E-MAIL/USB

CHANGE

MENU

EXIT

1/4

Note f

The projector status can also be displayed using the menu operation. Refer to the [PROJECTOR SETUP] menu → [STATUS] ( x

page 122) for details.

Using the ECO management function

Display the setting screen relating to ECO management.

button

1) Press the <ECO> button.

Note f

Refer to the [PROJECTOR SETUP] menu → [ECO MANAGEMENT] ( x

page 106) for details.

Using the HDMI-CEC function

Display the HDMI-CEC operation screen.

button

1) Press the <CEC> button.

f

The HDMI-CEC operation screen is displayed.

Note f

Refer to the [PROJECTOR SETUP] menu → [HDMI CEC] ( x

page 125) for details.

Setting ID number of the remote control

When you use the multiple projectors together, you can operate all the projectors simultaneously or each projector individually using a single remote control, if a unique ID number is assigned to each projector.

After setting the ID number of the projector, set same ID number on the remote control.

The factory default ID number of the projector is set to [ALL]. When using a single projector, press the <ID

ALL> button on the remote control. Also, you can control a projector by pressing the <ID ALL> button on the remote control even if you do not know the projector ID.

button

1) Press the <ID SET> button on the remote control.

2) Within five seconds, press and set the one-digit or two-digit ID number set on the projector body using the number (<0> - <9>) buttons.

f

If you press the <ID ALL> button, you can control the projectors regardless of the ID number setting of the projector body.

60 - ENGLISH

Chapter 3   Basic Operations — Operating with the remote control

Attention f

Since the ID number of the remote control can be set without the projector body, do not press the <ID SET> button on the remote control carelessly. If the <ID SET> button is pressed and no number (<0> - <9>) buttons are pressed within five seconds, the ID number returns to its original value before the <ID SET> button was pressed.

f

The ID number set on the remote control will be stored unless it is set again. However, it will be erased if the remote control is left with dead batteries. Set the same ID number again when the batteries are replaced.

Note f

When the ID number of the remote control is set to [0], you can control the projector regardless of the ID number setting of the projector body, as same as when [ALL] is set.

f

Set the ID number of the projector body from the [PROJECTOR SETUP] menu → [PROJECTOR ID].

ENGLISH - 61

Chapter 4 Settings

This chapter describes the settings and adjustments you can make using the on-screen menu.

62 - ENGLISH

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents