[ADVANCED MENU] menu. Panasonic PT-FRQ60BU7, PT-FRQ60WU7

Add to my manuals
221 Pages

advertisement

[ADVANCED MENU] menu. Panasonic PT-FRQ60BU7, PT-FRQ60WU7 | Manualzz

Chapter 4   Settings — [ADVANCED MENU] menu

[ADVANCED MENU] menu

On the menu screen, select [ADVANCED MENU] from the main menu, and select an item from the submenu.

Refer to “Navigating through the menu” ( x page 63) for the operation of the menu screen.

[DIGITAL CINEMA REALITY]

The picture quality is enhanced by raising the vertical resolution higher performing the cinema processing when interlaced video signal is input.

1) Press as

to select [DIGITAL CINEMA REALITY].

2) Press qw to switch the item.

f

The items will switch each time you press the button.

[AUTO]

[OFF]

[30p FIXED]

[25p FIXED]

Automatically detects the signal and performs the cinema processing. (Factory default setting)

Does not perform cinema processing.

When 60 Hz vertical scanning frequency signals are input

When 50 Hz vertical scanning frequency signals are input

Performs forced cinema processing

(2:2 pulldown).

Note f

In [DIGITAL CINEMA REALITY], the picture quality will degrade when a signal other than the 2:2 pulldown is set as [25p FIXED] or [30p

FIXED]. (Vertical resolution will degrade.) f

When the [ADVANCED MENU] menu → [FRAME RESPONSE] is set to [FAST], [DIGITAL CINEMA REALITY] cannot be set.

[BLANKING]

Adjust the blanking width if there is a noise at the edge of the screen or the image is slightly running out from the screen.

1) Press as

to select [BLANKING].

2) Press the <ENTER> button.

f The [BLANKING] adjustment screen is displayed.

3) Press as to select [UPPER], [LOWER], [LEFT], or [RIGHT].

f When [CUSTOM MASKING] is selected and set to anything other than [OFF] ([PC-1], [PC-2], [PC-3]), the blanking width can be adjusted to arbitrary shape using a computer and the masking function of the

“Geometric & Setup Management Software”. Up to three adjustment data can be saved.

4) Press qw

to adjust the blanking width.

Blanking correction Item Range of adjustment Operation

Press q

.

The blanking zone moves upward.

Adjustment

Top of the screen [UPPER]

Press w

.

The blanking zone moves downward.

Top and bottom 0 - 1079

Press w

.

The blanking zone moves upward.

Bottom of the screen [LOWER]

Press q

.

The blanking zone moves downward.

84 - ENGLISH

Blanking correction

Left side of the screen

Right side of the screen

Chapter 4   Settings — [ADVANCED MENU] menu

Item Operation

Press w

.

The blanking zone moves to the right.

Adjustment

[LEFT]

Press q

.

The blanking zone moves to the left.

[RIGHT]

Press q

.

Press w

.

The blanking zone moves to the right.

The blanking zone moves to the left.

Range of adjustment

Left and right 0 - 1919

Note f

The upper limit of the adjustment range may be restricted so that the entire projected image is not covered by blanking width.

f

When inputting certain high resolution signals, the [CUSTOM MASKING] setting in [BLANKING] is disabled, and the masking function in the

“Geometric & Setup Management Software” cannot be used.

f

“Geometric & Setup Management Software” can be downloaded from the website (https://panasonic.net/cns/projector/pass/). It is necessary to register and login to PASS to download.

[INPUT RESOLUTION]

You can adjust the image to achieve an optimal image when there is a flickering image or smeared outlines.

1) Press as

to select [INPUT RESOLUTION].

2) Press the <ENTER> button.

f

The [INPUT RESOLUTION] screen is displayed.

3) Press as

to select [DISPLAY DOTS], [TOTAL LINES], or [DISPLAY LINES], and press qw

to adjust each item.

f Values corresponding to the signal being input are displayed automatically for each item. Increase or decrease the displayed values and adjust to the optimal point while viewing the screen if there are vertical stripes or sections are missing from the screen.

Note f

Previously mentioned vertical banding will not occur with all white signal input.

f

Image may be disrupted during automatic adjustment, but this is not a malfunction.

f

[INPUT RESOLUTION] can be adjusted only when an RGB signal is input to the <COMPUTER IN> terminal.

f

Adjustment may not be possible depending on the signal.

[CLAMP POSITION]

You can adjust the optimal point when the black part of the image is blunt or it has turned green.

1) Press as

to select [CLAMP POSITION].

2) Press qw

to adjust.

Status

The black part is blunt.

The black part is green.

Rough guide for optimal value

The point where bluntness of the black part improves the most is the optimal value.

The point where the green part becomes black, and the bluntness has improved is the optimal value.

Range of adjustment

1 - 255

Note f

[CLAMP POSITION] can be adjusted only when a signal is input to the <COMPUTER IN> terminal.

f

Adjustment may not be possible depending on the signal.

[EDGE BLENDING]

The edge blending function allows multiple images to be seamlessly overlapped by using the inclination of the brightness at the overlapped area.

ENGLISH - 85

Chapter 4   Settings — [ADVANCED MENU] menu

1) Press as

to select [EDGE BLENDING].

2) Press qw

to switch the item.

f

The items will switch each time you press the button.

[OFF]

[ON]

[USER]

Sets the edge blending function to off.

Use the setting value preset in the projector for the inclination of the edge blending area.

Use the user-setting value for the inclination of the edge blending area. (Configuration/registration requires separate software. Consult your dealer.) f

Proceed to Step 3) when anything other than [OFF] is selected.

3) Press the <ENTER> button.

f

The [EDGE BLENDING] screen is displayed.

4) Press as to specify the location to be corrected.

f

When joining at top: Set [UPPER] to [ON] f

When joining at bottom: Set [LOWER] to [ON] f

When joining at left: Set [LEFT] to [ON] f

When joining at right: Set [RIGHT] to [ON]

5) Press qw

to switch to [ON].

6) Press as to select [START] or [WIDTH].

7) Press qw

to adjust the starting position or correction width.

8) Press as

to select [MARKER].

9) Press qw

to switch to [ON].

f

A marker for image position adjustment is displayed. The position where the red and green lines overlap for the projectors to be joined will be the optimal point. Make sure to set the correction width for the projectors to be joined with the same value. Optimal joining is not possible with projectors that have different correction widths.

The optimal point is the point at which these lines overlap.

Green line

Red line

10) Press as

to select [BRIGHTNESS ADJUST].

11) Press the <ENTER> button.

f

The [BRIGHTNESS ADJUST] screen is displayed.

f

By setting [AUTO TESTPATTERN] to [ON] on the [EDGE BLENDING] screen, the black test pattern is displayed when you enter the [BRIGHTNESS ADJUST] screen.

12) Press as

to select [NON-OVERLAPPED BLACK LEVEL].

13) Press the <ENTER> button.

f

The [NON-OVERLAPPED BLACK LEVEL] screen is displayed.

f

[RED], [GREEN], and [BLUE] can be adjusted individually if [INTERLOCKED] is set to [OFF].

14) Press as

to select an item, and press qw

to adjust the setting.

f

Once the adjustment is completed, press the <MENU> button to return to the [BRIGHTNESS ADJUST] screen.

86 - ENGLISH

Chapter 4   Settings — [ADVANCED MENU] menu

15) Press as

to select [UPPER], [LOWER], [LEFT], or [RIGHT] in [BLACK BORDER WIDTH].

16) Press qw

to set the region (width) of the [BLACK BORDER WIDTH] adjustment.

17) Press as

to select [UPPER KEYSTONE AREA], [LOWER KEYSTONE AREA], [LEFT KEYSTONE

AREA], or [RIGHT KEYSTONE AREA].

18) Press qw

to adjust the tilt of the border between [NON-OVERLAPPED BLACK LEVEL] and [BLACK

BORDER LEVEL].

19) Press as

to select [BLACK BORDER LEVEL].

20) Press the <ENTER> button.

f

The [BLACK BORDER LEVEL] screen is displayed.

f

[RED], [GREEN], and [BLUE] can be adjusted individually if [INTERLOCKED] is set to [OFF].

21) Press as

to select an item, and press qw

to adjust the setting.

f

Once the adjustment is completed, press the <MENU> button to return to the [BRIGHTNESS ADJUST] screen.

22) Press as

to select [UPPER], [LOWER], [LEFT], or [RIGHT] for [OVERLAPPED BLACK LEVEL].

23) Press the <ENTER> button.

f

The [OVERLAPPED BLACK LEVEL] screen is displayed.

f [RED], [GREEN], and [BLUE] can be adjusted individually if [INTERLOCKED] is set to [OFF].

24) Press as

to select an item, and press qw

to adjust the setting.

Projection range

[BLACK BORDER WIDTH] (Right)

Edge blending [WIDTH] (Right)

[MARKER] (Red)

Edge blending [START] (Right)

([MARKER] (Green))

[OVERLAPPED BLACK LEVEL] (Right)

[BLACK BORDER LEVEL] [NON-OVERLAPPED BLACK LEVEL]

Note f

[BRIGHTNESS ADJUST] is a function that makes the increased brightness in black level of the overlapping image area difficult to notice when [EDGE BLENDING] is used to structure a multi-display screen. The optimal point of correction is set by adjusting [NON-OVERLAPPED

BLACK LEVEL] so the black level of the overlapping image area will be the same level as the non-overlapping area. If the border area of the part where the image is overlapping and the non-overlapping part gets brighter after adjusting [NON-OVERLAPPED BLACK LEVEL], adjust the width of the top, bottom, left, or right. Adjust [BLACK BORDER LEVEL] when the width adjustment makes only the border area darker.

f

The joining part may look discontinuous depending on the position you are looking from when a screen with high gain or rear screen is used.

f

When structuring a multi-display screen using both horizontal and vertical edge blending, adjust [OVERLAPPED BLACK LEVEL] first before making adjustments in Step 12) . Adjustment method is same as the procedure of [NON-OVERLAPPED BLACK LEVEL].

f

If only horizontal or vertical edge blending is used, set all items in [OVERLAPPED BLACK LEVEL] to 0.

f

The [AUTO TESTPATTERN] setting will change in conjunction with the setting in the [DISPLAY OPTION] menu → [COLOR MATCHING] →

[AUTO TESTPATTERN].

f

The tilt adjustment of the border between [NON-OVERLAPPED BLACK LEVEL] and [BLACK BORDER LEVEL] is a function to perform edge blending together with the adjustment in [GEOMETRY] ( x

page 78). If the area of [NON-OVERLAPPED BLACK LEVEL] is tilted by correcting the keystone distortion with the [POSITION] menu → [GEOMETRY] → [KEYSTONE], perform Steps 17) and 18) to adjust the tilt and adjust the edge blending according to the shape of [NON-OVERLAPPED BLACK LEVEL].

f

It is not recommended to use the edge blending function when the image of 1080/120p or 1920 x 1080/240 is projected.

[FRAME RESPONSE]

Set image frame delay.

1) Press as

to select [FRAME RESPONSE].

ENGLISH - 87

Chapter 4   Settings — [ADVANCED MENU] menu

2) Press qw

to switch the item.

f

The items will switch each time you press the button.

[NORMAL]

[FAST]

Standard setting.

Simplifies the image processing to reduce image frame delay.

Note f

When [FAST] is set, the picture quality deteriorates. The [ADVANCED MENU] menu → [DIGITAL CINEMA REALITY] cannot be set.

f

[FRAME RESPONSE] cannot be adjusted when the image of 1080/120p or 1920 x 1080/240 is projected.

[RASTER POSITION]

This will allow the position of the image to move within the display area arbitrarily when the input image is not using the whole display area.

1) Press as to select [RASTER POSITION].

2) Press the <ENTER> button.

f The [RASTER POSITION] screen is displayed.

3) Press asqw

to adjust the position.

88 - ENGLISH

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents