[PROJECTOR SETUP] menu. Panasonic PT-FRQ60BU7, PT-FRQ60WU7

Add to my manuals
221 Pages

advertisement

[PROJECTOR SETUP] menu. Panasonic PT-FRQ60BU7, PT-FRQ60WU7 | Manualzz

Chapter 4   Settings — [PROJECTOR SETUP] menu

[PROJECTOR SETUP] menu

On the menu screen, select [PROJECTOR SETUP] from the main menu, and select an item from the submenu.

Refer to “Navigating through the menu” ( x page 63) for the operation of the menu screen.

[PROJECTOR ID]

The projector has an ID number setting function that can be used when multiple projectors are used side by side to enable simultaneous control or individual control via a single remote control.

1) Press as

to select [PROJECTOR ID].

2) Press qw

to switch the item.

f

The items will switch each time you press the button.

[ALL]

[1] - [64]

Select this item when controlling projectors without specifying an ID number.

Select this item when specifying an ID number to control individual projector.

Note f

To specify an ID number for individual control, the ID number of a remote control must match the ID number of the projector.

f

When the ID number is set to [ALL], the projector will operate regardless of the ID number specified during remote control or computer control.

If multiple projectors are set up side by side with IDs set to [ALL], they cannot be controlled separately from the projectors with other ID numbers.

f

Refer to “Setting ID number of the remote control” ( x

page 60) for how to set the ID number on the remote control.

[PROJECTION METHOD]

Set the projection method in accordance with the installation status of the projector.

Change the [FRONT/REAR] setting when the screen display is inverted.

Change the [FLOOR/CEILING] setting when the screen display is upside down.

Setting [FRONT/REAR]

1) Press as

to select [PROJECTION METHOD].

2) Press the <ENTER> button.

f

The [PROJECTION METHOD] screen is displayed.

3) Press as

to select [FRONT/REAR].

4) Press qw

to switch the item.

f

The items will switch each time you press the button.

[FRONT]

[REAR]

Select this item when installing the projector in front of the screen.

Select this item when installing behind the screen (using translucent screen).

Setting [FLOOR/CEILING]

1) Press as

to select [PROJECTION METHOD].

2) Press the <ENTER> button.

f

The [PROJECTION METHOD] screen is displayed.

3) Press as

to select [FLOOR/CEILING].

4) Press qw

to switch the item.

f The items will switch each time you press the button.

[AUTO]

[FLOOR]

[CEILING]

Automatically detects the attitude of the projector by the built-in angle sensor.

Set [AUTO] normally.

Select this item when installing the projector on a desk, etc.

Select this item when installing the projector using the Ceiling Mount Bracket (optional).

Projected image is inverted upside down.

ENGLISH - 105

Chapter 4   Settings — [PROJECTOR SETUP] menu

Note f

Refer to “Angle sensor” ( x

page 34) for details on the range of the installation attitude that can be detected by the built-in angle sensor.

[ECO MANAGEMENT]

Set the operation method of the projector.

The settings are reflected when “Initial setting (operation setting)” ( x

page 45) in the [INITIAL SETTING] screen is already set.

If you change the settings while using the projector, the duration until the brightness decreases to half may shorten or the brightness may decrease.

Setting [OPERATING MODE]

1) Press as

to select [ECO MANAGEMENT].

2) Press the <ENTER> button.

f

The [ECO MANAGEMENT] screen is displayed.

3) Press as

to select [OPERATING MODE].

4) Press qw to switch the item.

f

The items will switch each time you press the button.

[NORMAL]

[ECO]

[QUIET]

Set this item to prioritize the brightness. [LIGHT OUTPUT] is 100 %, and the estimated runtime is approximately 20 000 hours *1 .

The brightness will decrease compared to [NORMAL], but set this item to prioritize the life of the light source. [LIGHT OUTPUT] is 80 %, and the estimated runtime is approximately 24 000 hours *1 .

The brightness will decrease compared to [NORMAL], but set this item to prioritize the operation with low noise. [LIGHT OUTPUT] is 80 %, and the estimated runtime is approximately 20 000 hours *1 .

Set [LIGHT OUTPUT] as desired.

[USER]

*1 Estimated runtime is the time until the brightness decreases to approximately half of the time of delivery when the projector is used with the

[PICTURE] menu → [DYNAMIC CONTRAST] set to [2] and under environment of 0.15 mg/m 3 dust. The value of runtime is just an estimate, and is not the warranty period.

f Proceed to Step 5) when [USER] is selected.

5) Press as

to select [LIGHT OUTPUT].

6) Press qw

to adjust.

Operation

Press w

.

Press q

.

Adjustment

Brightness

The screen becomes brighter.

Runtime (estimate)

The runtime becomes shorter.

The screen becomes darker.

The runtime becomes longer.

Range of adjustment

20 % - 100 %

Note f

When [USER] is selected, the uniformity of brightness between multiple screens can be maintained by adjusting [LIGHT OUTPUT] of each projector when a multi-display screen is structure with multiple projectors.

f

If the runtime exceeds 20 000 hours, replacement of the components inside the projector may be required. Consult your dealer for details.

Interrelation of brightness and runtime

The projector can be operated at arbitrary brightness and duration of use by combining the settings of [LIGHT

OUTPUT], and [CONSTANT MODE] in [BRIGHTNESS CONTROL SETUP].

The relationship between the [LIGHT OUTPUT] setting, brightness, and the estimated runtime is as follows. Make the setting depending on the desired brightness of the projected image and runtime.

The values of the brightness and the runtime are just an estimate, and the graph indicating the relationship is just an example. Also, these do not indicate the warranty period.

106 - ENGLISH

Chapter 4   Settings — [PROJECTOR SETUP] menu f

When [CONSTANT MODE] is set to [OFF]

[LIGHT OUTPUT] (%)

100.0

69.5

Brightness (lm)

PT-FRQ60 PT-FRQ50

6 000

4 200

5 200

3 600

Estimated runtime

20 000

24 000

*1 (hour)

29.0

1 700 1 500 27 000

*1 Estimated runtime is the time until the brightness decreases to approximately half of the time of delivery when the projector is used with the [PICTURE] menu → [DYNAMIC CONTRAST] set to [2] and under environment of 0.15 mg/m 3 dust.

100,0

90,0

80,0

70,0

60,0

50,0

40,0

30,0

20,0

20 000 21 000

5 200

3 600

/

/

6 000

4 200

1 500 / 1 700

22 000 23 000 24 000 25 000 26 000 27 000

Estimated runtime (hours) f

When [CONSTANT MODE] is set to [AUTO] or [PC]

[LIGHT OUTPUT] (%)

50.0

41.1

35.0

Brightness (lm)

PT-FRQ60

3 000

PT-FRQ50

2 600

2 500

2 100

2 100

1 800

Estimated runtime

20 000

24 000

27 000

*1 (hour)

27.4

20.7

1 600

1 200

1 400

1 100

31 000

35 000

*1 Estimated runtime is the time the brightness is maintained constant when the projector is used with the [PICTURE] menu → [DYNAMIC

CONTRAST] set to [2] and under environment of 0.15 mg/m 3 dust. The brightness will gradually decrease after exceeding this time.

60,0

50,0

40,0

30,0

20,0

10,0

20 000 23 000 26 000 29 000 32 000

Estimated runtime (hours)

35 000

2 600 / 3 000

2 100 / 2 500

1 800 / 2 100

1 400 / 1 600

1 100 / 1 200

Start of use Estimated runtime

Image of brightness change over time

Hours

Note f

Under influences of characteristics of each light source, conditions of use, installation environment, etc., the runtime may be shorter than the estimation.

f

If the runtime exceeds 20 000 hours, replacement of the components inside the projector may be required. Consult your dealer for details.

Setting [POWER MANAGEMENT]

Set the function to save power consumption when there is no input signal.

[NO SIGNAL LIGHTS-OUT]

This is a function to automatically turn off the light source of the projector when there is no input signal for specific period. The time until the light source is turned off can be set.

1) Press as to select [ECO MANAGEMENT].

2) Press the <ENTER> button.

f The [ECO MANAGEMENT] screen is displayed.

3) Press as

to select [POWER MANAGEMENT].

ENGLISH - 107

Chapter 4   Settings — [PROJECTOR SETUP] menu

4) Press the <ENTER> button.

f

The [POWER MANAGEMENT] screen is displayed.

5) Press as to select [NO SIGNAL LIGHTS-OUT].

6) Press qw

to switch the item.

f The items will switch each time you press the button.

[DISABLE]

[10SEC.] - [5MIN.]

Disables the no signal lights-out function.

Turns off the light source when there is no input signal for the preset period.

Select [10SEC.], [20SEC.], [30SEC.], [1MIN.], [2MIN.], [3MIN.], or [5MIN.].

Note f

The fan will rotate to cool the projector while the no signal lights-out function is operating and the light source is turned off. Also, the power indicator <ON (G)/STANDBY (R)> blinks slowly in green.

f

When [NO SIGNAL LIGHTS-OUT] is set to anything other than [DISABLE], the following are the conditions to turn the light source back on again from the condition that the light source has turned off by this function.

g

When the signal is input g

When on-screen display such as menu screen (OSD) or input guide, a test pattern, or a warning message is displayed g

When the power < v

/ b

> button is pressed g

When the operation to disable the shutter function (shutter: opened) is performed, such as pressing the <SHUTTER> button g

When the operating environment temperature is around 0 °C (32 °F) and the light source is forced to turn on due to warm-up f

The no signal lights-out function is disabled in following cases.

g

When [BACK COLOR] is set to [DEFAULT LOGO] or [USER LOGO], and the Panasonic logo or the image registered by the user is displayed in the projected image

[NO SIGNAL SHUT-OFF]

This is a function to automatically set the power of the projector to standby mode when there is no input signal for specific period. The time before switching to standby can be set.

1) Press as

to select [ECO MANAGEMENT].

2) Press the <ENTER> button.

f

The [ECO MANAGEMENT] screen is displayed.

3) Press as

to select [POWER MANAGEMENT].

4) Press the <ENTER> button.

f The [POWER MANAGEMENT] screen is displayed.

5) Press as

to select [NO SIGNAL SHUT-OFF].

6) Press qw

to switch the item.

f

The items will switch each time you press the button.

[DISABLE]

[10MIN.] - [90MIN.]

Disables the no signal shut-off function.

Sets the time in increments of 10 minutes.

Setting [STANDBY MODE]

Set the power consumption during standby and whether to enable the [QUICK STARTUP] function.

1) Press as

to select [ECO MANAGEMENT].

2) Press the <ENTER> button.

f

The [ECO MANAGEMENT] screen is displayed.

3) Press as

to select [STANDBY MODE].

4) Press qw

to switch the item.

f

The items will switch each time you press the button.

[NORMAL]

[ECO]

Select this item when using the network function during standby.

Select this item to reduce power consumption during standby.

f

Proceed to Step 5) when [NORMAL] is selected.

5) Press as

to select [QUICK STARTUP].

108 - ENGLISH

Chapter 4   Settings — [PROJECTOR SETUP] menu

6) Press qw

to switch the item.

f

The items will switch each time you press the button.

[OFF]

[ON]

Disables the [QUICK STARTUP] function.

Enables the [QUICK STARTUP] function until the specified time set in [VALID PERIOD] elapses after the projector enters the standby mode. The time until the projection starts after the power is turned on will be reduced during the period when the [QUICK STARTUP] function is valid.

f

Proceed to Step 7) when [ON] is selected.

7) Press the <ENTER> button.

f

The [QUICK STARTUP] screen is displayed.

8) Press qw

to switch [VALID PERIOD].

f The items will switch each time you press the button.

[30MIN.]

[60MIN.]

[90MIN.]

Sets the time until the [QUICK STARTUP] function is disabled after the projector enters the standby mode.

Select a desired valid period.

Note f

When [STANDBY MODE] is set to [NORMAL], the network function can be used during standby.

f

When [STANDBY MODE] is set to [NORMAL], the <USB (DC OUT)> terminal can supply power even in standby state. If set to [ECO], the

<USB (DC OUT)> terminal can not supply power in standby state.

f

When [STANDBY MODE] is set to [ECO], the network function and the audio output function cannot be used during standby. Also, some

RS-232C commands cannot be used.

f

When [STANDBY MODE] is set to [ECO], it takes longer for the projection to start after the power is turned on, compared to when set to

[NORMAL].

f

[STANDBY MODE] is fixed to [NORMAL] when the [PROJECTOR SETUP] menu → [SCHEDULE] is set to [ON].

f

[QUICK STARTUP] cannot be set when [STANDBY MODE] is set to [ECO].

f

When [QUICK STARTUP] is set to [ON], the power consumption during standby becomes high during the period when the [QUICK

STARTUP] function is valid.

f

If [QUICK STARTUP] is set to [ON], the [QUICK STARTUP] function is disabled when the time set in [VALID PERIOD] elapses after the projector enters the standby mode. The startup time and power consumption will be the same as when [QUICK STARTUP] is set to [OFF].

f

When [QUICK STARTUP] is set to [ON], the power indicator <ON (G)/STANDBY (R)> blinks red while in the standby mode during the period when the [QUICK STARTUP] function is valid. When [IN STANDBY MODE] in [AUDIO SETTING] is set to [OFF], the power indicator <ON

(G)/STANDBY (R)> will change to a red light when the specified time set in [VALID PERIOD] elapses after the projector enters the standby mode.

f

When [QUICK STARTUP] is set to [ON], the period when the [QUICK STARTUP] function is valid will be added as the projector runtime.

[BRIGHTNESS CONTROL]

The projector is equipped with a brightness sensor to measure brightness and color of the light source, and corrects brightness and white balance of the projected image according to the changes in brightness and color of the light source.

By using this function, in such a condition that multiple screens are configured using multiple projectors, you can reduce changes in overall brightness and white balance of the multiple screens due to aging of the light source and suppress variation in brightness and white balance to preserve uniformity.

Set the administrator accounts (user name and password) of all linked projectors to the same setting when performing brightness control of multiple projectors in synchronization.

Setting [BRIGHTNESS CONTROL SETUP]

Set the operation of the brightness control function.

1) Press as

to select [BRIGHTNESS CONTROL].

2) Press the <ENTER> button.

f

The [BRIGHTNESS CONTROL] screen is displayed.

3) Press as to select [BRIGHTNESS CONTROL SETUP].

4) Press the <ENTER> button.

f The [BRIGHTNESS CONTROL SETUP] screen is displayed.

5) Press as

to select [CONSTANT MODE].

ENGLISH - 109

Chapter 4   Settings — [PROJECTOR SETUP] menu

6) Press qw

to switch the item.

f

The items will switch each time you press the button.

[OFF]

[AUTO]

Does not perform automatic correction of the brightness and white balance.

Performs automatic correction to maintain the brightness and white balance based on the measurement result of the brightness sensor.

Synchronizes nine or more projectors using a computer and “Multi Monitoring & Control Software” *1 .

[PC]

*1 “Multi Monitoring & Control Software” can be downloaded from the website (https://panasonic.net/cns/projector/).

f

When [OFF] is selected, proceed to Step 9) .

f

When [PC] is selected, proceed to Step 11) .

7) Press as

to select [LINK].

8) Press qw

to switch the item.

f

The items will switch each time you press the button.

[OFF]

Performs automatic correction by this projector alone without synchronizing with other projectors.

The duration that the constant brightness is kept will become longer by setting the value of [LIGHT

OUTPUT] smaller.

[GROUP A]

[GROUP B]

[GROUP C]

[GROUP D]

Performs automatic correction by synchronizing multiple projectors.

Up to four groups (A to D) can be set within the same subnet by using the network function.

You can register and synchronize up to eight projectors in one group.

f

Proceed to Step 11) when [AUTO] is selected in Step 6) .

9) Press as

to select [STARTUP CALIBRATION].

10) Press qw

to switch the item.

f

The items will switch each time you press the button.

[OFF]

[ON]

Does not measure the brightness and color of the light source when the power is turned on.

Measures the brightness and color of the light source by the brightness sensor after the power is turned on and the light source is illuminated.

11) Press as

to select [REGULAR CALIBRATION].

12) Press qw

to switch the item.

f

The items will switch each time you press the button.

[OFF]

[ON]

Does not measure the brightness and color of the light source periodically.

Measures the brightness and color of the light source by the brightness sensor at the time specified by [CALIBRATION TIME].

f

Proceed to Step 17) when [OFF] is selected.

13) Press as

to select [CALIBRATION TIME].

14) Press the <ENTER> button.

f

The projector is in the adjustment mode (the time is blinking).

15) Press qw to select “hour” or “minute”, and press as or the number (<0> - <9>) buttons to set a time.

f

Selecting “hour” allows setting of only the hour in increments of one hour, and selecting “minute” allows setting of only the minute in increments of one minute between 00 and 59.

16) Press the <ENTER> button.

f

[CALIBRATION TIME] is set.

17) Press as

to select [CALIBRATION MESSAGE].

18) Press qw

to switch the item.

f

The items will switch each time you press the button.

[ON]

[OFF]

Displays the time to complete the measurement while the brightness and color of the light source are measured by the brightness sensor.

Does not display a message during the measurement.

110 - ENGLISH

Chapter 4   Settings — [PROJECTOR SETUP] menu

19) Press as

to select [APPLY].

20) Press the <ENTER> button.

f

When [CONSTANT MODE] is set to anything other than [OFF] and the <ENTER> button is pressed in following cases, the brightness and color of the light source at that time is set as the correction target for the brightness and white balance of the screen, and the automatic correction will start.

g

When [CONSTANT MODE] is set to anything other than [OFF] for the first time after purchasing the projector g

When [CONSTANT MODE] is set to anything other than [OFF] for the first time after executing the

[PROJECTOR SETUP] menu → [INITIALIZE] → [FACTORY RESET] f

When [CONSTANT MODE] was previously set to anything other than [OFF], and the correction target for the brightness and the white balance is already set, pressing the <ENTER> button displays the confirmation screen. Proceed to Step 21) .

f

When [LINK] is set to [GROUP A] to [GROUP D] and the <ENTER> button is pressed, the group name is displayed on the screens of the projectors that have been set as the same group.

LINK GROUP A

21) Press qw

to switch the item.

f The items will switch each time you press the button.

[YES]

[NO]

Maintains the previously set brightness and white balance as the correction target.

Reconfigures the current brightness and color of the light source as the correction target of the brightness and white balance of the screen.

22) Press the <ENTER> button.

f

Starts the automatic correction.

Note f

When [CONSTANT MODE] is set to [AUTO] or [PC], keep the shutter function disabled (shutter: opened) for at least two minutes, since the brightness sensor will measure the brightness and color of the light source after the [BRIGHTNESS CONTROL SETUP] setting has been completed.

f

If the projector operates with [CONSTANT MODE] set to [AUTO] or [PC], measurement of the brightness and color may not be possible when the shutter function is enabled (shutter: closed) within 10 minutes after turning on the light source. If the measurement was not possible, correction of the brightness is performed approximately two minutes after the shutter function is disabled (shutter: opened).

f

If the projector is operating with [CONSTANT MODE] set to [AUTO] or [PC], the brightness and color of the light source do not stabilize for approximately eight minutes after the light source is turned on. Therefore, the brightness and color of the light source will be automatically measured after approximately eight minutes have elapsed after the light source is turned on. A correction is made based on this measurement result so that the brightness and color for the image will be the same as the standard brightness and color when adjusted with the brightness control.

f

If the projector is operating with [CONSTANT MODE] set to [AUTO] or [PC], the items of [OPERATING MODE] and [LIGHT OUTPUT] cannot be changed.

f

The variation in brightness may increase due to dust accumulating on the lens, screen, or inside the projector, depending on the installation environment of the projector.

f

When the variation in brightness has increased due to aging of the light source, or when you replaced the light source, readjust the brightness control.

f

When the projector is used continuously for more than 24 hours, set [REGULAR CALIBRATION] to [ON]. If it is not set, correction will not be performed automatically.

f

The brightness control function and the dynamic contrast function will operate simultaneously, but the dynamic contrast function will not operate while measuring the brightness and color of the light source with the brightness sensor.

f

The setting of each item in [BRIGHTNESS CONTROL SETUP] will be reflected by selecting [APPLY] and pressing the <ENTER> button.

f

The [STARTUP CALIBRATION] setting item is common with the following menu item.

g

The [PROJECTOR SETUP] menu → [BRIGHTNESS CONTROL] → [STARTUP CALIBRATION] f

The [REGULAR CALIBRATION] setting item is common with the following menu item.

g

The [PROJECTOR SETUP] menu → [BRIGHTNESS CONTROL] → [REGULAR CALIBRATION] f

The [CALIBRATION TIME] setting item is common with the following menu item.

g

The [PROJECTOR SETUP] menu → [BRIGHTNESS CONTROL] → [CALIBRATION TIME] f

The [CALIBRATION MESSAGE] setting item is common with the following menu item.

g

The [PROJECTOR SETUP] menu → [BRIGHTNESS CONTROL] → [CALIBRATION MESSAGE]

ENGLISH - 111

Chapter 4   Settings — [PROJECTOR SETUP] menu

Displaying [BRIGHTNESS CONTROL STATUS]

Display the brightness control status.

1) Press as

to select [BRIGHTNESS CONTROL].

2) Press the <ENTER> button.

f

The [BRIGHTNESS CONTROL] screen is displayed.

3) Press as

to select [BRIGHTNESS CONTROL STATUS].

4) Press the <ENTER> button.

f

The [BRIGHTNESS CONTROL STATUS] screen is displayed.

[BRIGHTNESS CONTROL STATUS] screen display example

When [CONSTANT MODE] is set to [OFF]

The screen shows the status that the brightness control is disabled.

BRIGHTNESS CONTROL STATUS

CONSTANT MODE

PROJECTOR

OFF

1

MENU

RETURN

When [CONSTANT MODE] is set to [AUTO], and [LINK] is set to [OFF]

The screen shows the status of the brightness control in one projector.

BRIGHTNESS CONTROL STATUS

LINK

PROJECTOR

OFF 5

1

6

MENU

RETURN

When [CONSTANT MODE] is set to [AUTO], and [LINK] is set to [GROUP A] through [GROUP D]

The screen shows the status of the brightness control of synchronized projectors (up to eight units), including the projector being controlled through the on-screen menu.

BRIGHTNESS CONTROL STATUS

LINK

1:

2:

3:

4:

5:

6:

7:

UPDATE

PROJECTOR

PROJECTOR2

PROJECTOR3

GROUP A

192. 168. 30. 2

192. 168. 30. 3

192. 168. 30. 4

5

7

1

2

3

4

MENU SELECT

8

112 - ENGLISH

Chapter 4   Settings — [PROJECTOR SETUP] menu

When [CONSTANT MODE] is set to [PC]

BRIGHTNESS CONTROL STATUS

CONSTANT MODE

PROJECTOR

PC

5

1

6

MENU

RETURN

1 Display the name of the projector.

2 Display the synchronized group.

3 Display the IP address of the projector.

4 Display the names and IP addresses of projectors in same group detected over the network.

5 Display the status by color.

Green: There is an allowance for brightness correction.

Yellow: There is little allowance for brightness correction.

Red: There is a brightness control error.

6 Display error detailed messages.

7 Display error messages.

When the message [Failed to apply BRIGHTNESS CONTROL to some projectors.] appears, it means that synchronization with the projector displayed in red has failed.

Press as

to select the projector displayed in red, and press the <ENTER> button to display the error details.

8 Update to the latest status information.

r

Error details

Error message

[Exceed maximum number of projectors.]

[Please check the COMMAND

CONTROL setting.]

Measures to take f

Limit the number of projectors in one group to eight.

f

To synchronize nine or more projectors, use a PC and the dedicated software “Multi Monitoring &

Control Software” *1 .

f

Set the password of the administrator account. f

Set [NETWORK CONTROL] → [COMMAND CONTROL] to [ON] for the projector in error.

f

Set [NETWORK CONTROL] → [COMMAND PORT] of all projectors to be linked to the same value.

[Please check the USER NAME and PASSWORD in the COMMAND

CONTROL setting.]

[Cannot apply BRIGHTNESS

CONTROL. Please check projector status.] f

Set the same administrator account (user name and password) for all linked projectors. f

The projector is in standby. Switch on the power.

[Brightness Sensor Error] f

There is a problem with the brightness sensor. If problems persist even after switching on the power, consult your dealer.

*1 “Multi Monitoring & Control Software” can be downloaded from the website (https://panasonic.net/cns/projector/).

Note f

If the synchronized projectors are not displayed in the list, check the following: g

Are there devices with the same IP address on the network?

g

Are LAN cables connected correctly? ( x

page 149) g

Are the subnets of the projectors the same?

g

Are the same [LINK] settings applied to a group?

f

Refer to [PROJECTOR NAME] ( x

page 139) or “[Network config] page” ( x

page 162) on how to change the projector name.

Setting [STARTUP CALIBRATION]

Set whether to measure the brightness and color of the light source when the power is turned on.

1) Press as

to select [BRIGHTNESS CONTROL].

2) Press the <ENTER> button.

f The [BRIGHTNESS CONTROL] screen is displayed.

3) Press as

to select [STARTUP CALIBRATION].

4) Press qw

to switch the item.

f

The items will switch each time you press the button.

ENGLISH - 113

Chapter 4   Settings — [PROJECTOR SETUP] menu

[OFF]

[ON]

Does not measure the brightness and color of the light source when the power is turned on.

Measures the brightness and color of the light source by the brightness sensor after the power is turned on and the light source is illuminated.

Note f

The [STARTUP CALIBRATION] setting will be reflected at the time when the item is switched using qw

.

f

The [STARTUP CALIBRATION] setting item is common with the following menu item.

g

The [PROJECTOR SETUP] menu → [BRIGHTNESS CONTROL] → [BRIGHTNESS CONTROL SETUP] → [STARTUP CALIBRATION]

Setting [REGULAR CALIBRATION]

Set whether to measure the brightness and color of the light source at a specified time.

1) Press as

to select [BRIGHTNESS CONTROL].

2) Press the <ENTER> button.

f The [BRIGHTNESS CONTROL] screen is displayed.

3) Press as

to select [REGULAR CALIBRATION].

4) Press qw

to switch the item.

f

The items will switch each time you press the button.

[OFF]

[ON]

Does not measure the brightness and color of the light source periodically.

Measures the brightness and color of the light source by the brightness sensor at the time specified by [CALIBRATION TIME].

f

Proceed to Step 5) when [ON] is selected.

5) Press as

to select [CALIBRATION TIME].

6) Press the <ENTER> button.

f

The projector is in the adjustment mode (the time is blinking).

7) Press qw

to select “hour” or “minute”, and press as

or the number (<0> - <9>) buttons to set a time.

f

Selecting “hour” allows setting of only the hour in increments of one hour, and selecting “minute” allows setting of only the minute in increments of one minute between 00 and 59.

8) Press the <ENTER> button.

f

[CALIBRATION TIME] is set.

Note f

The [REGULAR CALIBRATION] setting will be reflected at the time when the item is switched using qw

.

f

The [CALIBRATION TIME] setting will be reflected at the time when you enter the time and then press the <ENTER> button.

f

The [REGULAR CALIBRATION] setting item is common with the following menu item.

g

The [PROJECTOR SETUP] menu → [BRIGHTNESS CONTROL] → [BRIGHTNESS CONTROL SETUP] → [REGULAR CALIBRATION] f

The [CALIBRATION TIME] setting item is common with the following menu item.

g

The [PROJECTOR SETUP] menu → [BRIGHTNESS CONTROL] → [BRIGHTNESS CONTROL SETUP] → [CALIBRATION TIME]

Setting [CALIBRATION MESSAGE]

Set whether to display the time to complete the measurement while the brightness and color of the light source are measured.

1) Press as

to select [BRIGHTNESS CONTROL].

2) Press the <ENTER> button.

f

The [BRIGHTNESS CONTROL] screen is displayed.

3) Press as

to select [CALIBRATION MESSAGE].

114 - ENGLISH

Chapter 4   Settings — [PROJECTOR SETUP] menu

4) Press qw

to switch the item.

f

The items will switch each time you press the button.

[ON]

[OFF]

Displays the time to complete the measurement while the brightness and color of the light source are measured by the brightness sensor.

Does not display a message during the measurement.

Note f

The [CALIBRATION MESSAGE] setting will be reflected at the time when the item is switched using qw

.

f

The [CALIBRATION MESSAGE] setting item is common with the following menu item.

g

The [PROJECTOR SETUP] menu → [BRIGHTNESS CONTROL] → [BRIGHTNESS CONTROL SETUP] → [CALIBRATION MESSAGE]

Brightness control adjustment procedure example

The steps exemplify an adjustment to link the brightness and white balance of eight projectors connected in a network.

1) Connect all projectors to the switching hub using LAN cables. ( x

page 149)

2) Switch on all projectors and start projection.

3) Set [CONSTANT MODE] of [BRIGHTNESS CONTROL SETUP] to [OFF], and select [APPLY], and then press the <ENTER> button.

4) Set [OPERATING MODE] of each projector to the same setting. ( x

page 106)

5) Set the administrator account, [SUBNET MASK], and [IP ADDRESS] of each projector.

f

Set the administrator account (user name and password) of all linked projectors to the same setting.

f

To be able to communicate over the network, set the same value in [SUBNET MASK] for all projectors and set a different value in [IP ADDRESS] for each projector.

6) Wait for at least eight minutes after projection has started until the light source brightness becomes steady.

7) Set all items in the [PICTURE] menu of all projectors to the same values.

8) Adjust [COLOR MATCHING] to match colors.

9) Display the internal test pattern “All white” in all projectors.

10) Set [LIGHT OUTPUT] of all projectors to 100 % or the maximum value that can be set.

f

Depending on the [OPERATING MODE] settings, [LIGHT OUTPUT] may not be able to be set to 100 %.

11) Set [LIGHT OUTPUT] of the projector with the least brightness to 90 % or 10 % lower than the maximum value that can be set.

12) Adjust [LIGHT OUTPUT] of each projector.

f Adjust [LIGHT OUTPUT] of all the other projectors so that the brightness will be the same as the projector with the least brightness.

13) Set [CONSTANT MODE] of [BRIGHTNESS CONTROL SETUP] to [AUTO], and [LINK] to [GROUP A] in all projectors.

14) Select [APPLY] of [BRIGHTNESS CONTROL SETUP] and press the <ENTER> button in all projectors.

f

Automatic correction by the brightness control function starts.

Note f

Automatic correction is performed whenever the light source lights up by switching on/off the projector, etc.

f

When the variation in brightness or color has increased due to aging of the light source, or when the light source is replaced, reset

[BRIGHTNESS CONTROL SETUP].

[INITIAL STARTUP]

Set the startup method when the <MAIN POWER> switch is set to <ON>.

1) Press as

to select [INITIAL STARTUP].

ENGLISH - 115

Chapter 4   Settings — [PROJECTOR SETUP] menu

2) Press qw

to switch the item.

f

The items will switch each time you press the button.

[LAST MEMORY]

[STANDBY]

[ON]

Starts up the projector in the condition before the <MAIN POWER> switch is set to <OFF>.

Starts up the projector in standby.

Starts projecting immediately.

[STARTUP INPUT SELECT]

Set the input when the projector is switched on to start projection.

1) Press as

to select [STARTUP INPUT SELECT].

2) Press the <ENTER> button.

f

The [STARTUP INPUT SELECT] screen is displayed.

3) Press asqw

to select the input, and press the <ENTER> button.

[LAST USED]

[COMPUTER]

[HDMI1]

[HDMI2]

[DIGITAL LINK]

[INPUT1] - [INPUT10] *1

Keeps the input selected last.

Sets the input to COMPUTER.

Sets the input to HDMI1.

Sets the input to HDMI2.

Sets the input to DIGITAL LINK.

Sets the input to DIGITAL LINK, and switches the input of the DIGITAL LINK output supported device to the specified input.

*1 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, its input name is automatically reflected from [INPUT1] to [INPUT10]. When an item that does not reflect the input name is selected, it will be disabled.

[DATE AND TIME]

Set the time zone, date, and time of the built-in clock of the projector.

Setting the time zone

1) Press as

to select [DATE AND TIME].

2) Press the <ENTER> button.

f

The [DATE AND TIME] screen is displayed.

3) Press as to select [TIME ZONE].

4) Press qw

to switch [TIME ZONE].

Note f

The [TIME ZONE] setting is reset to the factory default setting when the projector is initialized by one of the following methods. However, the date and time based on the local date and time setting (Coordinated Universal Time, UTC, Universal Time, Coordinated) will be maintained without being initialized.

g

When initialized by selecting the [PROJECTOR SETUP] menu → [INITIALIZE] → [FACTORY RESET] g

When initialized by setting the [PROJECTOR SETUP] menu → [INITIALIZE] → [USER SETTINGS] → [OTHER USER SETTING] to

[INITIALIZE]

Setting the date and time manually

1) Press as

to select [DATE AND TIME].

116 - ENGLISH

Chapter 4   Settings — [PROJECTOR SETUP] menu

2) Press the <ENTER> button.

f

The [DATE AND TIME] screen is displayed.

3) Press as to select [ADJUST CLOCK].

4) Press the <ENTER> button.

f The [ADJUST CLOCK] screen is displayed.

5) Press as

to select an item, and press qw

to set the local date and time.

6) Press as

to select [APPLY], and press the <ENTER> button.

f

The setting of the date and time will be completed.

Note f

The replacement of the battery inside the projector is required when the time goes out of alignment right after correcting the time. Consult your dealer.

Setting the date and time automatically

To set the date and time automatically, the projector must be connected to the network.

1) Press as

to select [DATE AND TIME].

2) Press the <ENTER> button.

f

The [DATE AND TIME] screen is displayed.

3) Press as

to select [ADJUST CLOCK].

4) Press the <ENTER> button.

f The [ADJUST CLOCK] screen is displayed.

5) Press as

to select [NTP SYNCHRONIZATION], and press qw

to change the setting to [ON].

6) Press as

to select [APPLY], and press the <ENTER> button.

f

The setting of the date and time will be completed.

Note f

If synchronization with the NTP server fails just after [NTP SYNCHRONIZATION] is set to [ON], [NTP SYNCHRONIZATION] will return to

[OFF]. If [NTP SYNCHRONIZATION] is set to [ON] while the NTP server is not set, [NTP SYNCHRONIZATION] will return to [OFF].

f

Access the projector via a web browser to set the NTP server. Refer to “[Adjust clock] page” ( x

page 164) for details.

[SCHEDULE]

Set the command execution schedule for each day of the week.

Enabling/disabling the schedule function

1) Press as

to select [SCHEDULE].

2) Press qw to switch the item.

f

The items will switch each time you press the button.

[OFF]

[ON]

Disables the schedule function.

Enables the schedule function. Refer to “How to assign a program” ( x

page 117) or “How to set a program” ( x

page 118) for how to set the schedule.

Note f The [STANDBY MODE] setting will be forced to [NORMAL] when the [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [STANDBY

MODE] is set to [ECO], and [SCHEDULE] is set to [ON]. Changing the setting to [ECO] is not available. The [STANDBY MODE] setting will not change back even when [SCHEDULE] is set to [OFF] in this condition.

How to assign a program

1) Press as

to select [SCHEDULE].

2) Press qw

to select [ON], and press the <ENTER> button.

f

The [SCHEDULE] screen is displayed.

ENGLISH - 117

Chapter 4   Settings — [PROJECTOR SETUP] menu

3) Select and assign a program to each day of week.

f

Press as

to select the day of week, and press qw

to select a program number.

f

You can set the program from No.1 to No.7. “- - -” indicates that the program number has not been set.

How to set a program

Set up to 16 commands to each program.

1) Press as to select [SCHEDULE].

2) Press qw

to select [ON], and press the <ENTER> button.

f The [SCHEDULE] screen is displayed.

3) Press as

to select [PROGRAM EDIT].

4) Press qw

to select a program number, and press the <ENTER> button.

5) Press as

to select a command number, and press the <ENTER> button.

f

You can change the page using qw

.

6) Press asqw to select [TIME], and press the <ENTER> button.

f

The projector is in the adjustment mode (the time is blinking).

7) Press qw

to select “hour” or “minute”, and press as

or the number (<0> - <9>) buttons to set a time, and then press the <ENTER> button.

8) Press asqw

to select [COMMAND].

9) Press the <ENTER> button.

f

The [COMMAND] detailed screen is displayed.

10) Press as

to select a [COMMAND].

f

For [COMMAND] which requires detailed settings, the items of the detailed settings will switch each time you press qw

.

f

When [INPUT] is selected, press the <ENTER> button, and then press asqw

to select the input to be set.

[COMMAND]

[POWER ON]

[STANDBY]

Detailed settings of

[COMMAND]

Description

[QUICK STARTUP]

[SHUTTER]

[INPUT]

[OPERATING MODE]

[IN STANDBY

MODE(AUDIO)]

[VOLUME]

[ON]

[OFF]

[OPEN]

[CLOSE]

[COMPUTER]

[HDMI1]

[HDMI2]

[DIGITAL LINK]

[INPUT1] - [INPUT10] *1

[NORMAL]

[ECO]

[QUIET]

[USER]

[OFF]

[ON]

[0] - [63]

Switches on the projector.

Enters standby.

Enables the function of the [PROJECTOR SETUP] menu → [ECO

MANAGEMENT] → [QUICK STARTUP].

Disables the function of the [PROJECTOR SETUP] menu → [ECO

MANAGEMENT] → [QUICK STARTUP].

Disables the shutter function (shutter: open).

Enables the shutter function (shutter: closed).

Switches the input to COMPUTER.

Switches the input to HDMI1.

Switches the input to HDMI2.

Switches the input to DIGITAL LINK.

Switches the input to DIGITAL LINK, and switches the input of the

DIGITAL LINK output supported device to the specified input.

Prioritizes luminance.

Controls the power to increase the life of the light source although the luminance is lower than that of [NORMAL].

Prioritizes the operation with less noise although the luminance is lower than that of [NORMAL].

Controls the power with the setting set in [USER].

Stops the audio output during standby.

Outputs the audio during standby.

Sets the volume.

*1 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, its input name is automatically reflected from [INPUT1] to [INPUT10]. When an item that does not reflect the input name is selected, it will be disabled.

118 - ENGLISH

Chapter 4   Settings — [PROJECTOR SETUP] menu

11) Press the <ENTER> button.

f

The command is fixed and n

is displayed at the left of the selected command.

f

After the command is fixed, press the <MENU> button to close the detailed setting screen.

12) Press asqw

to select [STORE], and press the <ENTER> button.

Note f

To delete a command that has been already set, press the <DEFAULT> button on the remote control while the screen in Step 5) is displayed, or select [DELETE] at the screen in Step 6) and press the <ENTER> button.

f

If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command number.

f

The operating time will be the local time. ( x

page 116) f

If an operation is executed with the remote control or control panel of the projector or with a control command before the command set in

[SCHEDULE] is executed, the command set with the schedule function may not be executed.

[RS-232C]

Set the communication condition of the <SERIAL IN> terminal. Refer to “<SERIAL IN> terminal” ( x

page 207).

1) Press as

to select [RS-232C].

2) Press the <ENTER> button.

f The [RS-232C] screen is displayed.

3) Press as

to select [INPUT SELECT].

4) Press qw

to switch the item.

[PROJECTOR]

[DIGITAL LINK]

Performs the RS-232C communication with the <SERIAL IN> terminal of the projector.

Performs the RS-232C communication via the optional DIGITAL LINK output supported device (Model

No.: ET-YFB100G, ET-YFB200G) and the <DIGITAL LINK/LAN> terminal.

5) Press as

to select [BAUDRATE].

6) Press qw

to switch the item.

f The items will switch each time you press the button.

[9600]

[19200]

[38400]

Select the proper speed.

7) Press as

to select [PARITY].

8) Press qw

to switch the item.

f

The items will switch each time you press the button.

[NONE]

[EVEN]

[ODD]

Select the parity condition.

Note f

When [INPUT SELECT] is set to [DIGITAL LINK], communication using that serial terminal is available only when the corresponding device

(such as the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G)) is connected to the <DIGITAL LINK/

LAN> terminal.

f

When transferring logos via the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G), setting for “NO

SIGNAL SLEEP” of the DIGITAL LINK output supported device should be set to “OFF” to avoid interruption of communication.

f

The input communication speed is fixed to 9 600 bps when [INPUT SELECT] is set to [DIGITAL LINK].

[FUNCTION BUTTON]

Set the function of the <FUNCTION> button on the remote control.

1) Press as

to select [FUNCTION BUTTON].

2) Press the <ENTER> button.

f The [FUNCTION BUTTON] screen is displayed.

ENGLISH - 119

Chapter 4   Settings — [PROJECTOR SETUP] menu

3) Press as

to select a function.

[DISABLE]

[SUB MEMORY]

[SYSTEM SELECTOR]

[DAYLIGHT VIEW]

[FREEZE]

[WAVEFORM MONITOR]

[ASPECT]

[PROJECTION METHOD]

[GEOMETRY]

[OSD POSITION]

Disables the <FUNCTION> button.

Displays the sub memory list. ( x

page 132)

Switches the [SYSTEM SELECTOR] setting. ( x

page 74)

Switches the [DAYLIGHT VIEW] setting. ( x

page 72)

Temporarily pauses the image. ( x

page 103)

Displays the waveform of the input signal. ( x

page 103)

Switches the aspect ratio of the image. ( x

page 76)

Switches the [PROJECTION METHOD] setting. ( x

page 105)

Switches the [GEOMETRY] setting. ( x

page 78)

Switches the [OSD POSITION] setting. ( x

page 99)

4) Press the <ENTER> button.

Note f

The [FUNCTION BUTTON] screen can also be displayed by holding down the <FUNCTION> button on the remote control.

[AUDIO SETTING]

Set audio functions in detail.

Adjusting the volume

1) Press as

to select [AUDIO SETTING].

2) Press the <ENTER> button.

f

The [AUDIO SETTING] screen is displayed.

3) Press as

to select [VOLUME].

4) Press qw

to adjust the level.

Operation

Press w

.

Press q

.

Increases the volume.

Decreases the volume.

Adjustment Range of adjustment

0 - 63

Adjusting the left to right audio balance

1) Press as

to select [AUDIO SETTING].

2) Press the <ENTER> button.

f

The [AUDIO SETTING] screen is displayed.

3) Press as

to select [BALANCE].

4) Press qw to adjust the level.

Operation

Press w

.

Press q

.

Adjustment

Increases the volume on the right.

Increases the volume on the left.

Setting audio output in the standby mode

1) Press as

to select [AUDIO SETTING].

2) Press the <ENTER> button.

f The [AUDIO SETTING] screen is displayed.

3) Press as

to select [IN STANDBY MODE].

4) Press qw

to switch the item.

f

The items will switch each time you press the button.

Range of adjustment

L16 - R16

120 - ENGLISH

Chapter 4   Settings — [PROJECTOR SETUP] menu

[OFF]

[ON]

No audio is output during standby.

Audio is output during standby.

Note f

No audio is output in the standby mode when the [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] is set to

[ECO].

Setting audio output while using the shutter function

1) Press as

to select [AUDIO SETTING].

2) Press the <ENTER> button.

f

The [AUDIO SETTING] screen is displayed.

3) Press as

to select [IN SHUTTER].

4) Press qw

to switch the item.

f

The items will switch each time you press the button.

[OFF]

[ON]

No audio is output while using the shutter function (shutter: closed).

Audio is output while using the shutter function (shutter: closed).

Setting mute mode

1) Press as

to select [AUDIO SETTING].

2) Press the <ENTER> button.

f

The [AUDIO SETTING] screen is displayed.

3) Press as

to select [MUTE].

4) Press qw to switch the item.

f

The items will switch each time you press the button.

[OFF]

[ON]

Audio is output.

No audio is output.

Setting audio input from a connected device

1) Press as

to select [AUDIO SETTING].

2) Press the <ENTER> button.

f

The [AUDIO SETTING] screen is displayed.

3) Press as to select item to set in [AUDIO IN SELECT].

[COMPUTER]

[HDMI1]

[HDMI2]

[DIGITAL LINK]

Sets the audio to output when COMPUTER is input.

Sets the audio to output when HDMI1 is input.

Sets the audio to output when HDMI2 is input.

Sets the audio to output when DIGITAL LINK is input.

4) Press qw

to switch the item.

f

The items will switch each time you press the button.

f The item is fixed to [AUDIO IN] when [COMPUTER] is selected.

[AUDIO IN]

[HDMI1 AUDIO IN] *1

[HDMI2 AUDIO IN] *2

[DIGITAL LINK AUDIO IN] *3

Audio connected to the <AUDIO IN> terminal is output during projection of image from the set input terminal.

Audio input to HDMI1 is output.

Audio input to HDMI2 is output.

Audio input to DIGITAL LINK is output.

*1 Only when the input signal is HDMI1

*2 Only when the input signal is HDMI2

*3 Only when the input signal is DIGITAL LINK

ENGLISH - 121

Chapter 4   Settings — [PROJECTOR SETUP] menu

[STATUS]

Display the status of the projector.

1) Press as to select [STATUS].

2) Press the <ENTER> button.

f The [STATUS] screen is displayed.

3) Press qw

to switch the pages.

f The page will change each time you press the button.

[PROJECTOR TYPE]

[SERIAL NUMBER]

[PROJECTOR RUNTIME]

[LIGHT RUNTIME]

Displays the projector type of the projector.

Displays the serial number of the projector.

Displays the runtime of the projector.

[CONTINUOUS LIGHTING

TIME]

Displays the runtime of the light source.

Displays the elapsed time from when the light source is illuminated.

The elapsed time after the illumination of the light source can be confirmed when adjusting the focus.

The elapsed time is reset when the light source is temporarily turned off such as using the shutter function.

[MAIN/SUB VERSION]

[INTAKE AIR TEMP.] *1

[OPTICS MODULE TEMP.] *1

[EXHAUST AIR TEMP.] *1

[LIGHT TEMP. 1] *1

[LIGHT TEMP. 2] *1

[SELF TEST]

[INPUT]

[SIGNAL NAME]

[MEMORY NO.]

[NUMBER OF REGISTERED

SIGNAL]

[COOLING CONDITION]

Displays the main and sub versions of the firmware of the projector.

Displays the status of the intake air temperature of the projector.

Displays the status of the internal temperature of the projector.

Displays the status of the exhaust air temperature of the projector.

Displays the temperature status for the front block of the light source (on the lens side).

Displays the temperature status for the rear block of the light source (on the exhaust vent side).

Displays the self-diagnosis information.

Displays the input terminal currently selected.

Displays the input signal name.

Displays the memory number of the input signal.

Displays the number of registered signals.

Displays the set cooling conditions.

[ATMOSPHERIC PRESSURE] Displays the atmospheric pressure.

[ON COUNT] [POWER ON TIMES] Displays the number of times the power is turned on.

[INPUT]

[SIGNAL FORMAT]

Displays the input terminal used for the projected image.

Displays the format of the input signal.

[SIGNAL INFORMATION]

[SAMPLING]

[SIGNAL LEVEL]

[GAMMA]

[COLOR SPACE]

Displays the sampling information of the input signal.

Displays the signal level of the input signal.

Displays the [GAMMA] setting.

Displays the [COLOR SPACE] setting.

*1 The temperature status is indicated with text color (green/yellow/red) and bar scale. Use the projector within the range that the indication is green.

r

[DETAILED INFORMATION]

[INPUT]

[SIGNAL FORMAT]

[SIGNAL FREQUENCY]

[SYNC. STATE]

[V.SYNC WIDTH]

[SCAN TYPE]

[TOTAL DOTS]

[DISPLAY DOTS]

Displays the input terminal used for the projected image.

Displays the format of the input signal.

Displays the frequency of the input signal.

Displays the sync polarity of the input signal.

Displays the vertical sync signal pulse width of the input signal.

Displays the scan type of the input signal.

Displays the total dot count of the input signal.

Displays the number of input signal display dots.

122 - ENGLISH

Chapter 4   Settings — [PROJECTOR SETUP] menu

[TOTAL LINES]

[DISPLAY LINES]

[SAMPLING]

[SIGNAL LEVEL]

[COLORIMETRY]

[HDCP STATUS]

Displays the total line count of the input signal.

Displays the number of input signal display lines.

Displays the sampling information and the color format of the input signal.

Displays the signal level of the input signal.

Displays the color gamut information of the input signal. The content of display is as follows.

[ITU-2020]: When the color gamut is compliant with ITU-R BT.2020 standard

[ITU-709]: When the color gamut is compliant with ITU-R BT.709 standard

[SMPTE 170M]: When the color gamut is compliant with SMPTE 170M standard

[---]: When there is no signal, when the color gamut information is not included in the InfoFrame information, or when the color gamut information other than [ITU-2020], [ITU-709], or [SMPTE 170M] is included

Displays the HDCP status of the input signal. The content of display is as follows.

[HDCP2.X]: When protected with HDCP 2.2 or HDCP 2.3

[HDCP1.X]: When protected with HDCP 1.X

[NONE]: When not protected with HDCP

[---]: When there is no signal r

[CONTENT INFORMATION]

[EOTF]

[MASTERING DISPLAY

COLOR VOLUME]

[CONTENT LIGHT LEVEL]

Displays EOTF (Electro-Optical Transfer Function) out of the InfoFrame information added to the input signal.

[RED]

Displays the chromaticity coordinates for the primary color red out of the

InfoFrame information added to the input signal.

[GREEN]

[BLUE]

Displays the chromaticity coordinates for the primary color green out of the

InfoFrame information added to the input signal.

Displays the chromaticity coordinates for the primary color blue out of the

InfoFrame information added to the input signal.

[WHITE]

[MAX LUMINANCE]

[MIN LUMINANCE]

[MaxCLL]

[MaxFALL]

Displays the chromaticity coordinates for the white point out of the InfoFrame information added to the input signal.

Displays the maximum brightness out of the InfoFrame information added to the input signal.

Displays the minimum brightness out of the InfoFrame information added to the input signal.

Displays MaxCLL (Maximum Content Light Level) out of the InfoFrame information added to the input signal.

Displays MaxFALL (Maximum Frame Average Light Level) out of the InfoFrame information added to the input signal.

Note f

If you press the <ENTER> button while displaying [SIGNAL INFORMATION] in the page 4/4 of the [STATUS] screen, the [DETAILED

INFORMATION] screen can be displayed to view the detailed information of the input signal. Information for multiple input signals may be displayed depending on the projected image. Press qw

to switch pages.

f

While the [DETAILED INFORMATION] screen is displayed, press the <ENTER> button to display the [CONTENT INFORMATION] screen, and the contents of the InfoFrame information added to the input signal can be displayed.

f

There are items that are displayed or not displayed in [SIGNAL INFORMATION], [DETAILED INFORMATION], and [CONTENT

INFORMATION] depending on the setting and the signal being input.

f

If any abnormality has occurred on the projector, press the <DEFAULT> button while the [STATUS] screen is displayed to check the details of the error information.

f

For details on the contents displayed in [SELF TEST], refer to “Self-diagnosis display” ( x

page 197).

Sending status content via E-mail

The status content can be sent to the E-mail address (up to two addresses) set in “[E-mail set up] page”

( x

page 173).

1) Press the <ENTER> button while the 1/4 to 3/4 page of the [STATUS] screen is displayed.

f

The selection screen is displayed.

2) Press as

to select [SEND E-MAIL].

3) Press the <ENTER> button.

f The [SELECT E-MAIL ADDRESS] screen is displayed.

4) Press as

to select the destination.

ENGLISH - 123

Chapter 4   Settings — [PROJECTOR SETUP] menu

5) Press the <ENTER> button.

f

The confirmation screen is displayed.

6) Press qw to select [OK], and press the <ENTER> button.

f

The status content is sent.

Saving status content in USB memory

The status content can be saved in a USB memory attached to the <USB (DC OUT)> terminal.

1) Press the <ENTER> button while the 1/4 to 3/4 page of the [STATUS] screen is displayed.

f The selection screen is displayed.

2) Press as

to select [SAVE TO USB MEMORY].

3) Press the <ENTER> button.

f

The confirmation screen is displayed.

4) Press qw

to select [OK], and press the <ENTER> button.

f

The status content is saved.

[DATA CLONING]

Perform the operation of the data cloning function. Data such as the settings and adjustment values of the projector can be copied to multiple projectors via LAN or using the USB memory.

For details of operation, refer to “Using the data cloning function” ( x

page 179).

[SAVE ALL USER DATA]

Save the various setting values as a backup in the built-in memory of the projector.

1) Press as

to select [SAVE ALL USER DATA].

2) Press the <ENTER> button.

f

The [SECURITY PASSWORD] screen is displayed.

3) Enter a security password and press the <ENTER> button.

4) When the confirmation screen is displayed, press qw to select [OK], and press the <ENTER> button.

f

[PROGRESS] is displayed while saving data.

Note f

Data set from the computer application is not included in [SAVE ALL USER DATA].

f

The data saved by executing [SAVE ALL USER DATA] is not deleted even if the [PROJECTOR SETUP] menu → [INITIALIZE] → [FACTORY

RESET] is executed.

[LOAD ALL USER DATA]

Load the various setting values saved as a backup in the built-in memory of the projector.

1) Press as

to select [LOAD ALL USER DATA].

2) Press the <ENTER> button.

f

The [SECURITY PASSWORD] screen is displayed.

3) Enter a security password and press the <ENTER> button.

4) When the confirmation screen is displayed, press qw

to select [OK], and press the <ENTER> button.

Note f

The projector enters the standby mode to reflect the setting values when [LOAD ALL USER DATA] is executed.

f

Data registered from a computer is not included in [LOAD ALL USER DATA].

124 - ENGLISH

Chapter 4   Settings — [PROJECTOR SETUP] menu

[HDMI CEC]

Sets the CEC (Consumer Electronics Control) function of HDMI.

CEC is a function that is realized by exchanging device control signals with external devices connected with an HDMI cable. Using the remote control of the projector, it is possible to operate the CEC-compatible external device (hereinafter referred to as "CEC-compatible device") and to control the power on/off link status between the projector and the CEC-compatible device.

For details on how to use the CEC function, refer to “Using HDMI-CEC function” ( x

page 183).

1) Press as

to select [HDMI CEC].

2) Press qw to switch the item.

f

The items will switch each time you press the button.

[ON]

[OFF]

Enables the CEC function.

Disables the CEC function.

Operating a CEC-compatible device

Operate the CEC-compatible device connected to the <HDMI IN 1> terminal or <HDMI IN 2> terminal.

[HDMI-CEC OPERATION] can be operated when HDMI1 input or HDMI2 input is selected. Switch to the input that is corresponding to the CEC-compatible device you want to operate in advance.

1) Press as

to select [HDMI CEC].

2) Press qw

to select [ON].

3) Press the <ENTER> button.

f

The [HDMI CEC] screen is displayed.

4) Press as to select [HDMI 1] or [HDMI 2].

f

Select the input corresponding to the CEC-compatible device you want to operate.

f

Proceed to Step 6) when the device to operate is displayed.

5) Press qw to switch the item.

f

The devices will switch when multiple CEC-compatible devices are connected to one input.

f

Select the device to operate.

6) Press as to select [HDMI-CEC OPERATION].

7) Press the <ENTER> button.

f The HDMI-CEC operation screen is displayed.

8) Select the item displayed on the HDMI-CEC operation screen to operate the device.

f Refer to the “Using HDMI-CEC function” ( x page 183) for the operation details.

Note f

If no CEC-compatible device is connected to <HDMI IN 1> or <HDMI IN 2> terminal, there is no device displayed at [HDMI 1] or [HDMI 2] and [----] is displayed.

f

To exit the HDMI-CEC operation screen, press the <RETURN> button or <MENU> button.

Changing the menu code

The menu code that calls up the operation menu of the CEC-compatible device varies depending on the device manufacturer. If you cannot call up the operation menu of a CEC-compatible device from the HDMI-CEC operation screen, change the menu code setting.

1) Press as to select [HDMI CEC].

2) Press qw

to select [ON].

3) Press the <ENTER> button.

f

The [HDMI CEC] screen is displayed.

4) Press as

to select [MENU CODE].

ENGLISH - 125

Chapter 4   Settings — [PROJECTOR SETUP] menu

5) Press qw

to switch the item.

f

The items will switch each time you press the button.

f

Select the menu code from [1] to [6].

Setting the link control

Make settings for the link control between the projector and CEC-compatible devices.

[PROJECTOR -> DEVICE]

Set the link control from the projector to the CEC-compatible device.

1) Press as

to select [HDMI CEC].

2) Press qw

to select [ON].

3) Press the <ENTER> button.

f

The [HDMI CEC] screen is displayed.

4) Press as

to select [PROJECTOR

->

DEVICE].

5) Press qw to switch the item.

f

The items will switch each time you press the button.

[DISABLE]

[POWER OFF]

[POWER ON/OFF]

Disables the power link control from the projector to the CEC-compatible device.

Select this when you do not want the power status of the CEC-compatible device to link with the power status of the projector.

Enables power-off link control.

When you turn off the power of the projector and put it in standby mode, all CEC-compatible devices connected to the <HDMI IN 1> terminal or <HDMI IN 2> terminal will enter standby mode.

Power-on link control is disabled.

Enables power-on link control and power-off link control.

If you turn on the projector and start projection with the HDMI1 input or HDMI2 input selected, the CECcompatible device connected to the selected input will turn on.

When you turn off the projector and put it in standby mode, all CEC-compatible devices connected to the

<HDMI IN 1> terminal or <HDMI IN 2> terminal will enter standby mode.

[DEVICE -> PROJECTOR]

Set the link control from the CEC-compatible device to the projector.

1) Press as

to select [HDMI CEC].

2) Press qw

to select [ON].

3) Press the <ENTER> button.

f The [HDMI CEC] screen is displayed.

4) Press as

to select [DEVICE

->

PROJECTOR].

5) Press qw

to switch the item.

f

The items will switch each time you press the button.

[DISABLE]

[POWER ON]

[POWER ON/OFF]

Disables the power link control from the CEC-compatible device to the projector.

Select this when you do not want the power status of the projector to link with the power status of the CECcompatible device.

Enables power-on link control.

While the projector is in standby, if the CEC-compatible device connected to the <HDMI IN 1> terminal or

<HDMI IN 2> terminal is turned on or starts playing, the projector turns on, starts projection, and switches to the input that the linked CEC-compatible device is connected. While the projector is turned on, if the CECcompatible device starts playing, the projector switches to the input that the CEC-compatible device is connected.

Power-off link control is disabled.

Enables power-on link control and power-off link control.

While the projector is in standby, if the CEC-compatible device connected to the <HDMI IN 1> terminal or

<HDMI IN 2> terminal is turned on or starts playing, the projector turns on, starts projection, and switches to the input that the linked CEC-compatible device is connected. While the projector is turned on, if the CECcompatible device starts playing, the projector switches to the input that the CEC-compatible device is connected.

When the CEC-compatible device connected to the selected input is turned off, the projector enters standby mode.

126 - ENGLISH

Chapter 4   Settings — [PROJECTOR SETUP] menu

Note f

If the CEC-compatible device does not support CEC 1.4, it may not support the link control described in the manual.

f

Depending on the connected CEC-compatible device, the link control may not operate normally.

[INITIALIZE]

Return various setting values to their factory default settings.

1) Press as

to select [INITIALIZE].

2) Press the <ENTER> button.

f

The [SECURITY PASSWORD] screen is displayed.

3) Enter a security password and press the <ENTER> button.

f The [INITIALIZE] screen is displayed.

4) Press as

to select an item to initialize.

[USER SETTINGS]

[REGISTERED SIGNAL ONLY]

The user data to return to factory default settings can be selected arbitrarily.

The projector goes into the standby status after executing [INITIALIZE].

For details of operation, refer to “Initializing the settings by selecting the items” ( x

page 127).

Deletes all the signals registered in [SIGNAL LIST]. All the setting values saved for each registered signal are also deleted.

[NETWORK/E-MAIL ONLY]

[LOGO IMAGE ONLY]

[UNIFORMITY ONLY]

[FACTORY RESET]

Returns all the setting items under the [NETWORK] menu and all the setting items under the operation page in the [Detailed set up] page and the Crestron Connected of the web control screen to the factory default settings.

f

The items of [Time Zone], [Date], and [Time] in the [Adjust clock] page of the web control screen do not return to the factory default settings.

f

The information such as the self-signed certificate already created in the [Certificate] page of the web control screen or the server certificate already installed is not deleted.

Deletes the image registered in [USER LOGO].

Sets the setting of the [DISPLAY OPTION] menu → [UNIFORMITY] to the factory default setting.

Returns all the user data settings to the factory default settings. The projector goes into the standby status after executing [FACTORY RESET].

f

Proceed to Step 5) when anything other than [USER SETTINGS] is selected.

5) Press the <ENTER> button.

f

The confirmation screen is displayed.

6) Press qw

to select [OK], and press the <ENTER> button.

Note f

The security password is the password set in the [SECURITY] menu → [SECURITY PASSWORD CHANGE]. Initial password as the factory default: awsqawsq f

To delete only a part of a registered signal, delete it following “Deleting the registered signal” ( x

page 130).

f

To return the setting of [Time Zone] in the [Adjust clock] page of the web control screen and the setting of the [PROJECTOR SETUP] menu

→ [DATE AND TIME] → [TIME ZONE] to the factory default settings, initialize them by one of the following methods.

g

Initializing by selecting the [PROJECTOR SETUP] menu → [INITIALIZE] → [FACTORY RESET] g

Initializing by setting the [PROJECTOR SETUP] menu → [INITIALIZE] → [USER SETTINGS] → [OTHER USER SETTING] to [INITIALIZE] f

The self-signed certificate already created in the [Certificate] page of the web control screen or the information of the server certificate already installed can be deleted in the web control screen.

f

If initialized by selecting [FACTORY RESET], the [INITIAL SETTING] screen is displayed when the projection is started the next time.

Initializing the settings by selecting the items

1) Press as to select [INITIALIZE].

2) Press the <ENTER> button.

f The [SECURITY PASSWORD ] screen is displayed.

3) Enter a security password and press the <ENTER> button.

f The [INITIALIZE] screen is displayed.

4) Press as

to select [USER SETTINGS].

5) Press the <ENTER> button.

f

The [USER SETTINGS] screen is displayed.

ENGLISH - 127

Chapter 4   Settings — [PROJECTOR SETUP] menu

6) Press as

to select an item.

[OPERATING MODE]

[STANDBY MODE]

[REGISTERED SIGNAL]

The [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [OPERATING MODE] is initialized.

The [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] is initialized.

[NETWORK/E-MAIL]

All the signals registered in [SIGNAL LIST] are initialized.

All the setting items under the [NETWORK] menu and all the setting items under the operation page in the [Detailed set up] page and the Crestron Connected of the web control screen are initialized.

f

The items of [Time Zone], [Date], and [Time] in the web control screen are not initialized.

f The information such as the self-signed certificate already created in the [Certificate] page of the web control screen or the server certificate already installed is not initialized.

[LOGO IMAGE]

[UNIFORMITY]

Image registered in [USER LOGO] is initialized.

The [DISPLAY OPTION] menu → [UNIFORMITY] is initialized.

[OTHER USER SETTING] The user data other than mentioned above are initialized.

7) Press qw

to switch the setting.

f

The items will switch each time you press the button.

[KEEP]

[INITIALIZE]

Does not return to the factory default settings and maintains the current settings when initialization is executed by [USER SETTINGS].

Returns to the factory default settings when initialization is executed by [USER SETTINGS].

f

Repeat Steps 6) to 7) until the desired initialization items are set.

8) Press as

to select [INITIALIZE].

9) Press the <ENTER> button.

f

The confirmation screen is displayed.

10) Press qw

to select [OK], and press the <ENTER> button.

Note f

To return the setting of [Time Zone] in the [Adjust clock] page of the web control screen and the setting of the [PROJECTOR SETUP] menu

→ [DATE AND TIME] → [TIME ZONE] to the factory default settings, initialize them by one of the following methods.

g

Initializing by selecting the [PROJECTOR SETUP] menu → [INITIALIZE] → [FACTORY RESET] g

Initializing by setting the [PROJECTOR SETUP] menu → [INITIALIZE] → [USER SETTINGS] → [OTHER USER SETTING] to [INITIALIZE]

[FIRMWARE UPDATE]

Rewriting of the firmware is possible by using a USB memory.

For details of operation, refer to “Updating the firmware using the USB memory” ( x

page 189).

[SERVICE PASSWORD]

This function is used by a service person.

128 - ENGLISH

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents