Using the web control function. Panasonic PT-FRQ60BU7, PT-FRQ60WU7

Add to my manuals
221 Pages

advertisement

Using the web control function. Panasonic PT-FRQ60BU7, PT-FRQ60WU7 | Manualzz

Chapter 5   Operations — Using the web control function

Using the web control function

Following operation is possible from a computer using the web control function.

f Setting and adjustment of the projector f

Display of the projector status f

Sending E-mail messages when there is a problem with the projector

The projector supports “Crestron Connected”, and the following application software of Crestron Electronics, Inc. can be used.

f

Crestron Fusion

Note f

Communication with an E-mail server is required to use the E-mail function. Confirm that the E-mail can be used beforehand.

f

“Crestron Connected” is a system of Crestron Electronics, Inc. that collectively manages and controls devices on multiple systems connected to a network using a computer.

f

For details of “Crestron Connected”, visit the website of Crestron Electronics, Inc. (English only)

URL https://www.crestron.com

Computer that can be used for setting

To use the web control function, a web browser is required. Confirm that the web browser can be used in advance.

OS

Windows

Mac OS iOS

Android

Compatible browser

Internet Explorer 11.0, Microsoft Edge

Safari 11.0/12.0/13.0/14.0/15.0

Safari (version equipped with iOS 11, iOS 12, iOS 13, iOS 14 and iOS 15)

Google Chrome (version equipped with Android 7.0/8.0/9.0/10.0/11.0/12.0)

Accessing from the web browser

1) Start up the web browser on the computer.

2) Enter the IP address set on the projector into the URL entry field of the web browser.

f

If the user name and password of the administator account have been set on the initial setting screen

( x

page 49) or in the [NETWORK] menu → [ADMINISTRATOR ACCOUNT] ( x

page 140) , proceed to

Step 7) .

f The [Set up password] page is displayed if the administrator account has not been set.

3) In [User name], enter the user name of the administrator account.

f

The factory default setting of user name is "dispadmin".

4) In [Password], enter the password of the administrator account.

f

The password cannot be blank.

f

A password consisting of at least eight single-byte characters is recommended.

f A password consisting of at least three of the following four character types is recommended. g Uppercase letters g g

Digits g

Lowercase lettters

Symbols (~!@#$%^&*()_+\|}{][<>.,/?`)

5) In [Password(Retype)], re-enter the password entered in Step 4).

154 - ENGLISH

Chapter 5   Operations — Using the web control function

6) Click [Change].

f

Setting of the administrator account is completed.

7) Enter the user name and password on the displayed login screen.

f

Enter the user name and password of the administrator account, or the user name and password of a standard user account without administrator rights.

f

After logging in with the administrator account, set the user name and password of the standard user account using the [Set up password] page. For details, refer to “[Set up password] page (for administrator account)” ( x

page 176).

8) Click [Sign in] or [OK].

Attention f

The entry screen for the user name and password may be hidden by other window that is already opened. In such case, minimize the window in front to display the entry screen.

Note f

If you use a web browser to control the projector, set the [NETWORK] menu → [NETWORK CONTROL] → [WEB CONTROL] to [ON].

f

Do not perform setting or control simultaneously by starting up multiple web browsers. Do not set or control the projector from multiple computers.

f

Access will be locked for few minutes when an incorrect password is entered three times consecutively.

f

Some items on the projector setting page use the JavaScript function of the web browser. Correct control may not be possible when the web browser is set not to use this function.

f

If the screen for the web control is not displayed, consult your network administrator.

f

While updating the screen for the web control, the screen may appear white for a moment, but it is not a malfunction.

f

Click [License] at the top right of the [Set up password] page to display the download page of the open source software license.

f

Screenshot of a computer

The size or the display of the screen may be different from this manual depending on the OS or the web browser, or the type of computer in use.

ENGLISH - 155

Chapter 5   Operations — Using the web control function

Rights for each account

The administrator account allows use of all functions. There is a limitation in the functions that can be used with the standard user account. Select the account depending on the purpose.

The function that has l

in the administrator / standard user column indicates that it can be operated with their respective accounts.

Item

[Status]

[Projector control]

[Detailed set up]

[Set up password]

Function

[Remote preview lite]

[Projector status]

Error information page

[Network status]

[Access error log]

[Mail error log]

[Basic control]

[Detail control]

[Network config]

[Adjust clock]

[Ping test]

[Certificate]

[HTTPS set up]

[Crestron Connected]

[E-mail set up]

[Authentication set up]

[User function set up]

[Status notification]

[Network security]

User name of [Administrator]

User name of [User]

Password of [Administrator]

Password of [User]

Password of [PJLink]

License download page

Administrator l l l l l l l l l l l l l l l l l l l l l l l l l

Standard User l l l

*1

165

170

171

173

162

162

164

164

Page

157

159

160

160

160

161

161

174

175

175

176

177

177

177

177, 178

178

178 l

― l

― l

― l

[License] *2

*1 Available only when [Detailed set up] → [User function set up] → [Remote preview lite] is set to [Enable]. When [Disable] is set, the [Remote preview lite] page cannot be displayed or operated with the standard user account.

*2 Even if an administrator account is not set, the license can be downloaded from the [Set up password] page that is displayed when accessing the projector.

Descriptions of items

1

3

4

5

PT-FRQ50

6

1 Page tab

Switches pages by clicking this item.

2 [Status]

The status of the projector is displayed by clicking this item.

3 [Projector control]

The [Projector control] page is displayed by clicking this item.

4 [Detailed set up]

The [Detailed set up] page is displayed by clicking this item.

156 - ENGLISH

5 [Set up password]

The [Set up password] page is displayed by clicking this item.

6 [License]

The download page of the open source software license is displayed by clicking this item.

Chapter 5   Operations — Using the web control function

[Status]

[Remote preview lite] page

The input image to the projector can be simply viewed on the web control screen.

Click [Status] → [Remote preview lite].

6

8

4

5

1

2

3

14

SN1234567

9

10

11

12

13

SN1234567

15

1 Preview window

Simply displays the image corresponding to the input image to the projector.

Color of the outside border of the preview window indicates the projection status from the projector.

Red: Image from the projector is not projected.

Green: Image from the projector is being projected.

2 [INPUT SELECT]

Displays the operation menu for switching input.

For details, refer to “Switching the input” ( x

page 159).

3 [STATUS]

Displays the status of the projector.

4 [SHUTTER]

Displays the status of the shutter.

5 [POWER]

Displays the status of the power.

6 [OSD]

Displays the status of the on-screen display function.

7 [PROJECTOR TYPE]

Displays the type of the projector.

8 [SERIAL NUMBER]

Displays the serial number of the projector.

Note

9 Signal information

Displays the signal information of the selected input.

10 [INTAKE AIR]

Displays the intake air temperature status.

11 [GEOMETRY]

Displays the setting of the [POSITION] menu → [GEOMETRY].

12 [LIGHT SOURCE]

Displays the illumination status (icon) and the runtime of the light source.

13 [ERROR]

Displays the occurrence status of error/warning in icon.

This will be blank if there is no occurrence of error/warning.

14 [Pre-Show Mode]

Switches the Pre-Show mode.

In the Pre-Show mode, the input image to the projector can be viewed without projecting even if the projector is in the standby status.

[Pre-Show Mode] is not displayed in the projection mode.

15 [Detail]

A button is displayed when there is an occurrence of error/ warning.

Click “Error information page” ( x

page 160) to display.

f

The power indicator <ON (G)/STANDBY (R)> blinks in red in frequency of 2.95 seconds illuminating → 0.25 seconds off during the Pre-

Show mode.

f

The runtime in [PROJECTOR RUNTIME] continues to add up even if the projector is in the standby status while in the Pre-Show mode.

f

In case of this projector, the input image to the projector can be displayed in the preview window in simplified manner even if [Detailed set up] → [HTTPS set up] → [Connection] is set to [HTTPS]. However, it may not be displayed depending on the web browser in use when the self-signed certificate is used as the security certificate to be used for the HTTPS communication.

f

There are following restrictions on the image to be displayed in the preview window.

g

The adjustment results for each item in the [PICTURE] menu, [POSITION] menu, and [ADVANCED MENU] menu are not reflected.

However, some of the items such as [CONTRAST], [BRIGHTNESS], or [SHIFT] are reflected.

g

When an image is projected with a different aspect ratio from the input image using [ASPECT] or [ZOOM], the image may be displayed with a different aspect ratio from the actual projected image.

g

The effects set in [BACK COLOR] or [STARTUP LOGO] are not reflected.

f

The test pattern built-in to the projector is displayed in the preview window if it is being projected.

ENGLISH - 157

r

Status display icon

Chapter 5   Operations — Using the web control function

The power is switched off. (Standby status)

[POWER]

In the projection mode

[SHUTTER]

[OSD]

[GEOMETRY]

The shutter function is enabled (shutter: closed).

The shutter function is disabled (shutter: opened).

The on-screen display is set to on (display).

The on-screen display is set to off (hide).

The [POSITION] menu → [GEOMETRY] is set to [OFF].

The [POSITION] menu → [GEOMETRY] is set to [KEYSTONE].

The [POSITION] menu → [GEOMETRY] is set to [CORNER CORRECTION].

The [POSITION] menu → [GEOMETRY] is set to [CURVED CORRECTION].

The light source is illuminated.

[LIGHT SOURCE]

The light source is not illuminated.

[ERROR]

The light source is in warning status.

The light source is in error status.

The temperature is in warning status.

The temperature is in error status.

A warning other than light source or temperature has occurred.

An error other than light source or temperature has occurred.

158 - ENGLISH

Chapter 5   Operations — Using the web control function

Switching the input

Click [INPUT SELECT] in the [Remote preview lite] page.

1

2

3

4

1 [INPUT SELECT]

Switches to the input to view the image.

2 [INPUT]

Displays the input terminal currently selected.

Note

3 [SIGNAL NAME]

Displays the input signal name.

4 [SIGNAL FREQUENCY]

Displays the frequency of the input signal.

f

View the input image in the Pre-Show mode, and turn on the power in [Projector control] → [Basic control] page/[Detail control] page if there is no problem to project.

[Projector status] page

Click [Status] → [Projector status].

Display the status of the projector for the following items.

3

4

1

2

5

PT-FRQ50

11

12

13

14

6

7

8

9

10

15

16

17

1 [PROJECTOR TYPE]

Displays the type of the projector.

2 [MAIN VERSION]

Displays the firmware version of the projector.

3 [POWER]

Displays the status of the power.

4 [SHUTTER]

Displays the status of the shutter function ([CLOSE]: Enabled

(closed), [OPEN]: Disabled (open)).

5 [OPERATING MODE]

Displays the setting status of [OPERATING MODE].

6 [SERIAL NUMBER]

Displays the serial number of the projector.

7 [OSD]

Displays the status of the on-screen display.

8 [VOLUME]

Display the volume status.

9 [LIGHT OUTPUT]

Displays the setting status of [LIGHT OUTPUT].

10 [INPUT]

Displays the status of the selected input.

11 [INTAKE AIR TEMPERATURE]

Displays the status of the intake air temperature of the projector.

12 [OPTICS MODULE TEMPERATURE]

Displays the status of the internal temperature of the projector.

13 [EXHAUST AIR TEMPERATURE]

Displays the status of the exhaust air temperature of the projector.

14 [LIGHT TEMPERATURE1], [LIGHT TEMPERATURE2]

Displays the temperature status of the light source.

15 [LIGHT]

Displays the lighting status and runtime of the light source.

16 [SELF TEST]

Displays the self-diagnosis information.

17 [PROJECTOR RUNTIME]

Displays the runtime of the projector.

ENGLISH - 159

Chapter 5   Operations — Using the web control function

Error information page

When [Error (Detail)] or [Warning (Detail)] is displayed in the [SELF TEST] display field of the [Projector status] screen, click it to display the content of the error/warning.

f

The projector may go into the standby status to protect the projector depending on the contents of the error.

PT-FRQ50

1

2

Error ( Detail )

1 Display of error information

Displays the alphanumeric symbols and content of errors/ warnings that occur.

Refer to “Self-diagnosis display” ( x

page 197) for the display details.

[Network status] page

Click [Status] → [Network status].

The current network setting status is displayed.

2 Error code

1

2

1

1 [WIRED LAN]

Displays the settings of wired LAN.

2 [WIRELESS LAN]

Displays the settings of wireless LAN when the optional Wireless

Module (Model No.: AJ-WM50 Series) is attached.

[Access error log] page

Click [Status] → [Access error log].

The error log on the web server is displayed such as access to the pages that do not exist or access with unauthorized user names or passwords.

160 - ENGLISH

Chapter 5   Operations — Using the web control function

[Mail error log] page

Click [Status] → [Mail error log].

E-mail error log is displayed if periodic E-mail sending has failed.

Note f

[Access error log] and [Mail error log] display the recent few thousand accesses/requests. All information may not be displayed when many accesses/requests are made at once.

f

Logs in [Access error log] and [Mail error log] are deleted from the oldest when exceeding a certain amount.

f

Check [Access error log] and [Mail error log] periodically.

[Projector control]

[Basic control] page

Click [Projector control] → [Basic control].

5

6

3

4

1

2

1 [POWER]

Turns off/on the power.

2 [SHUTTER]

Switches the status of the shutter. ([CLOSE]: Shutter function enabled; [OPEN]: Shutter function disabled)

3 [OSD]

Switches the status of the on-screen display function. ([OFF]:

Hide; [ON]: Display)

4 [SYSTEM]

Switches the system method.

5 On-screen display of the projector

Displays the same items as shown on the on-screen display of the projector. You can check or change the settings of the menus.

It is displayed even if the on-screen display function is set to off

(hide).

6 [INPUT SELECT]

Switches the input signal.

ENGLISH - 161

Chapter 5   Operations — Using the web control function

[Detail control] page

Click [Projector control] → [Detail control].

1

2

3

4

5

6

7

8

9

10

1 Control of the projector

The projector is controlled by clicking the buttons in the same way as the buttons on the remote control. After control, the on-screen display of the projector at the right of the control page is updated.

2 [SUB MEMORY]

Switches the sub memory.

3 [DAYLIGHT VIEW]

Switches the day light view setting.

4 [FREEZE]

Temporarily pauses the image.

5 [WAVEFORM MONITOR]

Displays the waveform of the input signal.

6 [PROJECTION METHOD]

Switches the setting of the projection method.

7 [OSD POSITION]

Switches the OSD position setting.

8 [GEOMETRY]

Switches the geometric adjustment setting.

9 [TEST PATTERN]

Displays the test pattern.

Click the test pattern to display in the projected image from the patters displayed on the right side of the control page.

The display of the test pattern disappears if [Exit] is clicked.

10 [GET OSD]

Updates the on-screen display of the projector at the right of the control page.

[Detailed set up]

[Network config] page

Click [Detailed set up] → [Network config].

1) Click [Network config].

f

Click [Network config] to display the [CAUTION!] screen.

2) Select the item to change the setting.

f

The [WIRELESS LAN] setting can be selected only when the optional Wireless Module (Model No.:

AJ-WM50 Series) is attached.

3) Click [Next].

f

The current settings are displayed.

4) Click [Change].

f

The setting change screen is displayed.

162 - ENGLISH

Chapter 5   Operations — Using the web control function

For wired LAN connection

5

6

3

4

7

8

1

2

1 [PROJECTOR NAME]

Enter the name of the projector. Enter the host name if it is required when using a DHCP server etc.

2 [DHCP ON], [DHCP OFF]

To enable the DHCP client function, set to [DHCP ON].

3 [IP ADDRESS]

Enter the IP address when not using a DHCP server.

4 [SUBNET MASK]

Enter the subnet mask when not using a DHCP server.

5 [DEFAULT GATEWAY]

Enter the default gateway address when not using a DHCP server.

6 [DNS1]

Enter the DNS1 server address.

Permissible characters for the entry of DNS1 server address

(primary):

Numbers (0 - 9), period (.)

(Example: 192.168.0.253)

Note

7 [DNS2]

Enter the DNS2 server address.

Available characters for the entry of DNS2 server address

(secondary):

Numbers (0 - 9), period (.)

(Example: 192.168.0.254)

8 [Back], [Next]

Click [Back] to return to the original screen. Click [Next] to display the setting confirmation screen. Click [Submit] to update the setting.

f When you use the “Forward” and “Back” functions of your browser, a warning message “Page has Expired” may appear. In that case, click

[Network config] again since the following operation will not be guaranteed.

f Changing LAN settings while connected to the LAN may cause the connection to disconnect.

For wireless LAN connection

(Available only when the Wireless Module is attached to the projector)

1

2

1 [KEY]

Sets the connection key.

Enter 8 to 15 characters of single-byte alphanumeric.

2 [Back], [Next]

Click [Back] to return to the original screen. Click [Next] to display the setting confirmation screen. Click [Submit] to update the setting.

ENGLISH - 163

Chapter 5   Operations — Using the web control function

[Adjust clock] page

Click [Detailed set up] → [Adjust clock].

1

2

6

7

4

5

1 [Time Zone]

Select the time zone.

2 [Set time zone]

Updates the time zone setting.

3 [NTP SYNCHRONIZATION]

Set [ON] when adjusting the date and time automatically.

4 [NTP SERVER NAME]

Enter the IP address or server name of the NTP server when you set to adjust the date and time manually.

(To enter the server name, the DNS server needs to be set up.)

Note

5 [Date]

Enter the date to change when [NTP SYNCHRONIZATION] is set to [OFF].

6 [Time]

Enter the time to change when [NTP SYNCHRONIZATION] is set to [OFF].

7 [Submit]

Updates the date and time settings.

f

The replacement of the battery inside the projector is required when the time goes out of alignment right after correcting the time. Consult your dealer.

[Ping test] page

Check whether the network is connected to the E-mail server, POP server, DNS server, etc.

Click [Detailed set up] → [Ping test].

1

2

3

4

1 [Input IP address]

Enter the IP address of the server to be tested.

2 [Submit]

Executes the connection test.

3 Example of display when the connection has succeeded

4 Example of display when the connection has failed

164 - ENGLISH

Chapter 5   Operations — Using the web control function

[Certificate] page

To perform the HTTPS communication or use the control system or application software of Crestron Electronics,

Inc., it is necessary to install the certificate for authentication into the projector.

Click [Detailed set up] → [Certificate].

1

2

3

1 [CRT Key generate]

Generates the CRT (Certificate) key.

The page to generate the CRT key is displayed by clicking

[Execute].

For details, refer to “Generating the CRT key” ( x

page 166).

2 [Self-signed Certificate]

[Generate]:

Generates the self-signed certificate by the projector.

The page to generate the self-signed certificate is displayed by clicking [Execute].

For details, refer to “Generating the self-signed certificate”

( x

page 169).

[Information]:

Displays the status of the self-signed certificate.

f

[Not generated]: Self-signed certificate is not generated.

f

[(host name)]: Self-signed certificate is generated and valid.

The host name registered in the self-signed certificate is displayed.

f

[Invalid (Reason: Server Certificate installed)]: The server certificate is valid, so the generated self-signed certificate is invalid.

Information of the generated self-signed certificate is displayed by clicking [Confirm].

The generated self-signed certificate can be deleted by clicking

[Delete].

For details, refer to “Confirming the information of the self-signed certificate” ( x

page 170).

3 [Server Certificate]

[Generate Certificate Signing Request]:

Generates signing request (Certificate Signing Request).

The page to generate the signing request is displayed by clicking

[Execute].

For details, refer to “Generating the signing request”

( x

page 168).

[Server Certificate install]/[Intermediate Certificate install]:

Installs the server certificate and the intermediate certificate.

The certificate is installed into the projector by specifying the certificate file and clicking [Execute].

For details, refer to “Installing the certificate” ( x

page 168).

[Information]:

Displays the status of the server certificate.

f

[Invalid]: The server certificate is not installed. Or, the current

CRT key is different from the CRT key used for requesting the installed server certificate.

f

[(host name)]: The server certificate is installed and valid. The host name registered in the server certificate is displayed.

f

[Expired]: Valid period of the server certificate has expired.

The host name registered in the server certificate is displayed when the server certificate is installed and valid.

Information of the installed server certificate is displayed by clicking [Confirm].

The installed server certificate and the intermediate certificate can be deleted by clicking [Delete].

For details, refer to “Confirming the information of the server certificate” ( x

page 169).

Note f

Installation operation of the certificate may not be possible depending on the computer or web browser in use.

ENGLISH - 165

Chapter 5   Operations — Using the web control function r

Flow for setting

The flow for setting differs depending on which certificate is to be used as the security certificate, either the server certificate or the self-signed certificate.

Generate the CRT key.

When using the server certificate When using the self-signed certificate

Generate the signing request.

Acquire the server certificate.

Install the certificate.

Generate the self-signed certificate.

Select the connection method.

Set the HTTPS port number.

Click [Set].

Note f

When using the server certificate, the procedure from application to the certification organization to issuing of the server certificate is required to be performed between the customer and the certification organization. For the application method, etc., contact the certification organization.

Generating the CRT key

Generate the CRT key used for encryption with the RSA (Rivest-Shamir-Adleman cryptosystem) public key encryption method. CRT key is a type of the private key.

1) Click [Certificate] → [CRT Key generate] → [Execute].

f The page to generate the CRT key is displayed.

2) Click [Execute].

f

When generating the CRT key for the first time, the following message is displayed after the CRT is generated. Proceed to Step 4) .

“CRT key - Generated” f When generating the CRT key for the second time or later, the following message is displayed.

“The CRT key will be generated. In updating the CRT key, the Server Certificate corresponds to the current

CRT key will become unavailable. Continue?”

166 - ENGLISH

Chapter 5   Operations — Using the web control function

3) Click [OK].

f

CRT key will be generated and the following message will be displayed.

“CRT key - Generated”

4) Click [OK].

f

Clicking [Certificate] → [CRT Key generate] → [Execute] again can confirm the key length and generation date and time of the current CRT key with the [RSA key size] and [Last modified] of [Current CRT key] at the upper row of the CRT key generation page.

Note f

[Not generated] displayed in [Last modified] indicates that the CRT has not been generated.

f

[RSA key size] is fixed to [2048bit]. The server certificate may not be issued depending on the certification organization to apply if the key length is 2048-bit.

f

Generation of the CRT key may take up to approximately two minutes.

f

When the CRT key is updated, apply for the server certificate or generate the self-signed certificate again using that CRT key. A certificate linked to the CRT key is required.

f

Previously generated CRT key information is saved even if the CRT key is updated. To return to the previous CRT key, refer to “Cancelling the update of the CRT key” ( x

page 167).

Cancelling the update of the CRT key

It is possible to return to the previously generated CRT key only once even if the CRT key is updated.

1) Click [Certificate] → [CRT Key generate] → [Execute].

f The page to generate the CRT key is displayed.

2) Click [History].

f

Following contents are displayed.

3) Confirm [RSA key size] and [Last modified] of the CRT key to restore.

4) Click [Apply].

f

Following confirmation message is displayed.

“The previous CRT key will be loaded. Please generate Self-signed Certificate or install the Server

Certificate corresponds to the CRT key. Continue?”

5) Click [OK].

f

Previously generated CRT key is reflected as the current CRT key.

Note f

When returned to the previously generated CRT key, a certificate linked to that CRT key is required.

ENGLISH - 167

Chapter 5   Operations — Using the web control function

Generating the signing request

When using the server certificate issued by the certification organization as a security certificate, generate a signing request necessary for application of issuing to the certification organization. Generate the signing request after generating the CRT key.

1) Click [Certificate] → [Generate Certificate Signing Request] → [Execute].

f The page to generate the signing request is displayed.

2) Enter the information required for application.

f The details of each item are as follows. Enter the information following the requirement of the certification organization to apply.

Item Details

[Common Name] Enter the projector name or the IP address set in the projector.

[Country] Enter the country code defined in ISO 3166-1 alpha-2 (two upper case alphabets).

[State]

[Locality]

Enter the State, etc.

Enter the locality.

[Organization] Enter the organization name.

[Organization Unit] Enter the organization unit name.

[CRT key]

[RSA key size] The key length of the current CRT key is displayed.

[Last modified] The generation date and time of the current CRT key is displayed.

Character length limit

64 characters

128 characters

128 characters

64 characters

64 characters

3) Click [OK].

f

The signing request file is generated. Enter a file name and save the file in the desired folder.

4) Enter a file name and click [Save].

f The file for signing request is saved in the specified folder.

Note f

The characters that can be input are as follows.

g

Single-byte numbers: 0 to 9 g

Single-byte alphabets: A to Z, a to z g

Single-byte symbols: - . _ , + / ( ) f

The signing request generated by the projector is PEM format (file extension: pem).

f

Apply issuing of the server certificate to the certification organization using the saved signing request file (PEM format).

Installing the certificate

Install the server certificate and the intermediate certificate issued by the certification organization into the projector.

1) Click [Certificate] → [Server Certificate install] → [Browse].

f

A dialog to select the file is displayed.

2) Select the server certificate file and click [Open].

f

If the intermediate certificate is issued from the certification organization together with the server certificate, proceed to Step 3) .

f

If only the server certificate is issued from the certification organization, proceed to Step 5) .

3) Click [Browse] in [Intermediate Certificate install].

f

A dialog to select the file is displayed.

4) Select the intermediate certificate file and click [Open].

168 - ENGLISH

Chapter 5   Operations — Using the web control function

5) Click [Execute].

f

The server certificate and the intermediate certificate are installed into the projector.

6) Click [OK].

Note f

To confirm the information of the installed server certificate, refer to “Confirming the information of the server certificate” ( x

page 169).

Confirming the information of the server certificate

Confirm the information of the server certificate installed in the projector.

1) Click [Certificate] → [Server Certificate] → [Information] → [Confirm].

f

The information of the installed server certificate is displayed. The details of each item are as follows.

Item Details

[Common Name] The projector name or the IP address is displayed.

[Country] The country code defined in ISO 3166-1 alpha-2 (two upper case alphabets) is displayed.

[State]

[Locality]

The State, etc. is displayed.

The locality is displayed.

[Organization] The organization name is displayed.

[Organization Unit] The organization unit name is not displayed. It is displayed as an asterisk.

[Not Before] Displays the date and time that the self-signed certificate was issued.

[Not After] Displays the date and time that the self-signed certificate will expire.

[CRT key]

[RSA key size] The key length of the CRT key is displayed.

[Last modified] The generation date and time of the CRT key is displayed.

Note f

The installed server certificate and the intermediate certificate can be deleted by clicking [Certificate] → [Server Certificate] → [Delete].

However, it cannot be deleted when [HTTPS set up] → [Connection] is set to [HTTPS]. Delete it after changing the setting to perform the

HTTP communication.

To delete the server certificate within the valid period, confirm that the certificate file used for installing is available on hand. It will be necessary when installing the server certificate again.

Generating the self-signed certificate

When the server certificate issued by the certification organization is not to be used as the security certificate, it is possible to use the self-signed certificate generated in the projector. Generate the self-signed certificate after generating the CRT key.

1) Click [Certificate] → [Self-signed Certificate] → [Generate] → [Execute].

f

The page to generate the self-signed certificate is displayed.

2) Enter the information required for generation.

f

The details of each item are as follows.

ENGLISH - 169

Chapter 5   Operations — Using the web control function

Item Details

[Common Name] Enter the projector name or the IP address set in the projector.

[Country]

[State]

Enter the country code defined in ISO 3166-1 alpha-2 (two upper case alphabets).

Enter the State, etc.

[Locality]

[Organization]

Enter the locality.

Enter the organization name.

[Organization Unit] Enter the organization unit name.

[CRT key]

[RSA key size] The key length of the current CRT key is displayed.

[Last modified] The generation date and time of the current CRT key is displayed.

Character length limit

64 characters

128 characters

128 characters

64 characters

64 characters

3) Click [OK].

f

Self-signed certificate is generated.

Note f

The characters that can be input are as follows.

g

Single-byte numbers: 0 to 9 g

Single-byte alphabets: A to Z, a to z g

Single-byte symbols: - . _ , + / ( )

Confirming the information of the self-signed certificate

Confirm the information of the self-signed certificate generated by the projector.

1) Click [Certificate] → [Self-signed Certificate] → [Information] → [Confirm].

f

The information of the generated self-signed certificate is displayed. The details of each item are as follows.

Item

[Common Name] The projector name or the IP address is displayed.

Details

[Country]

[State]

[Locality]

[Organization]

The country code defined in ISO 3166-1 alpha-2 (two upper case alphabets) is displayed.

The State, etc. is displayed.

The locality is displayed.

The organization name is displayed.

[Organization Unit] The organization unit name is displayed.

[Not Before] Displays the date and time that the self-signed certificate was issued.

[Not After]

Displays the date and time that the self-signed certificate will expire (local time corresponding to 23:59,

December 31, 2035 in Greenwich Mean Time).

[CRT key]

[RSA key size] The key length of the CRT key is displayed.

[Last modified] The generation date and time of the CRT key is displayed.

Note f

The generated self-signed certificate can be deleted by clicking [Certificate] → [Self-signed Certificate] → [Delete].

However, it cannot be deleted when [HTTPS set up] → [Connection] is set to [HTTPS]. Delete it after changing the setting to perform the

HTTP communication.

[HTTPS set up] page

Set this page when HTTPS (Hypertext Transfer Protocol Secure) communication encrypted with the SSL/TLS protocol is to be performed between the computer and the projector while the web control function is used.

Click [Detailed set up] → [HTTPS set up].

To perform the HTTPS communication, it is necessary to install the certificate for authentication into the projector in advance. For details of installing the certificate, refer to “[Certificate] page” ( x page 165).

170 - ENGLISH

Chapter 5   Operations — Using the web control function

1

2

3

1 [Connection]

Sets the connection method to the projector.

f

[HTTP]: Uses the HTTP communication. (Factory default setting) f

[HTTPS]: Uses the HTTPS communication.

2 [HTTPS port]

Sets the port number to be used with the HTTPS communication.

Allowed port number: 1 to 65535

Factory default setting: 443

3 [Set]

Enables the setting.

Note f

When the [Connection] setting is changed from [HTTPS] to [HTTP], the screen may not be displayed when the operation or update of the web control screen is performed. In such case, delete the cache of the web browser.

[Crestron Connected] page

Set the information required for connecting the control system of Crestron Electronics, Inc. to the projector, and the information to monitor/control the projector using the control system of Crestron Electronics, Inc.

Click [Detailed set up] → [Crestron Connected].

r

[Control System]

Configure the setting for the control system required to connect to the projector as a client.

7

8

5

6

9

3

4

1

2

10

1 [Use TLS]

Sets the secure communication.

[Disable]:

Performs the unsecured communication.

[Enable]:

Performs the secure communication using TLS (Transport Layer

Security).

2 [IP Address / Hostname]

Enter the IP address or the host name of the connection destination.

3 [IP ID]

Sets the IP ID used to determine the projector on the network.

(A number up to four digits)

Default value: 3

4 [Room ID]

Sets the Room ID used to determine the projector on the network. (Up to 32 half-width characters)

5 [Non Secure Port]

Sets the port number to be used with the unsecured communication.

Default value: 41794

ENGLISH - 171

Chapter 5   Operations — Using the web control function

6 [Secure Port]

Sets the port number to be used with the secure communication.

Default value: 41796

7 [Authentication]

Select the authentication with the connection destination used with the secure communication.

[Disable]:

Does not perform the connection authentication.

[Enable]:

Performs the connection authentication.

Note

8 [User Name]

Enter the user name used for the connection authentication.

(Up to 20 half-width characters)

9 [Password]

Enter the password used for the connection authentication. (Up to 20 half-width characters)

10 [Submit]

Updates the [Control System] setting.

f

When [Use TLS] is set to [Disable], [Authentication] is fixed to [Disable], and [Secure Port] cannot be set.

r

[Server]

Configure the setting required to access the projector assigned to a server using the control system.

7

8

5

6

9

3

4

1

2

10

1 [Use TLS]

Sets the secure communication.

[Disable]:

Performs the unsecured communication.

[Enable]:

Performs the secure communication using TLS (Transport

Layer Security).

2 [IP ID]

Sets the IP ID used to determine the projector on the network.

(A number up to four digits)

3 [Non Secure Port]

Sets the port number to be used with the unsecured communication.

Default value: 41794

4 [Secure Port]

Sets the port number to be used with the secure communication.

Default value: 41796

5 [Authentication]

Select the authentication with the connection destination used with the secure communication.

[Disable]:

Does not perform the connection authentication.

[Enable]:

Performs the connection authentication.

6 [User Name]

Enter the user name used for the connection authentication.

(Up to 20 half-width characters)

7 [Password]

Enter the password used for the connection authentication. (Up to 20 half-width characters)

8 [Crestron Fusion in the Cloud (FITC)]

Sets whether to use the Fusion server in the Cloud.

[Disable]:

Does not use the Fusion server in the Cloud.

[Enable]:

Uses the Fusion server in the Cloud.

9 [FITC URL]

Enter the URL of the Fusion server in the Cloud.

10 [Submit]

Updates the [Server] setting.

Note f

[Use TLS] will be fixed to [Disable] if neither the server certificate nor the self-signed certificate is installed.

f

When [Use TLS] is set to [Disable], [Authentication] is fixed to [Disable], and [Secure Port] cannot be set.

f

When [Crestron Fusion in the Cloud (FITC)] is set to [Disable], [FITC URL] cannot be entered.

r

[Auto Discovery]

Set the standby process against the search protocol of the control system and the application software.

1

2

172 - ENGLISH

Chapter 5   Operations — Using the web control function

1 [Auto Discovery]

[Disable]:

Disables the standby process.

[Enable]:

Enables the standby process and enables the automatic detection of the projector.

2 [Submit]

Update the [Auto Discovery] setting

[E-mail set up] page

E-mail can be sent to preset E-mail addresses (up to two addresses) periodically or when an error or problem has occurred.

Click [Detailed set up] → [E-mail set up].

3

4

1

2

5

6

1 [ENABLE]

Select [ENABLE] to use the E-mail function.

2 [SMTP SERVER NAME]

Enter the IP address or the server name of the E-mail server

(SMTP). To enter the server name, the DNS server needs to be set up.

3 [MAIL FROM]

Enter the E-mail address of the projector. (Up to 63 characters in single byte)

4 [MEMO]

Enter information such as the location of the projector that notifies the sender of the E-mail. (Up to 63 characters in single byte)

5 [MINIMUM TIME]

Change the minimum interval for the temperature warning E-mail.

The default value is 60 minutes. In this case, another E-mail will not be sent for 60 minutes after sending the temperature warning

E-mail even if it reaches the warning temperature.

6 [INTAKE AIR TEMPERATURE]

Change the temperature setting for the temperature warning mail. A temperature warning E-mail is sent when the temperature exceeds this value.

7

8

7

8

9

7 [E-MAIL ADDRESS 1], [E-MAIL ADDRESS 2]

Enter the E-mail address to be sent. Leave [E-MAIL ADDRESS 2] blank when two E-mail addresses are not to be used.

8 Settings of the conditions to send E-mail

Select the conditions to send E-mail.

[MAIL CONTENTS]:

Select either [NORMAL] or [SIMPLE].

f

[NORMAL]: Select this item when sending detailed information including the status of the projector.

f

[SIMPLE]: Select this item when sending minimal information such as error information.

[ERROR]:

Send an E-mail when an error occurred in the self-diagnosis.

[INTAKE AIR TEMPERATURE]:

Send an E-mail when the intake air temperature has reached the value set at the above field.

[PERIODIC REPORT]:

Place a check mark on this to send an E-mail periodically.

It will be sent on the days and time with the check mark.

9 [Submit]

Update the settings.

ENGLISH - 173

Chapter 5   Operations — Using the web control function

[Authentication set up] page

Set the authentication items when POP authentication or SMTP authentication is necessary to send an E-mail.

Click [Detailed set up] → [Authentication set up].

5

6

3

4

7

1

2

8

1 [Auth]

Select the authentication method specified by your Internet service provider.

2 [SMTP Auth]

Set when the SMTP authentication is selected.

3 [POP server name]

Enter the POP server name.

Allowed characters:

Alphanumerics (A - Z, a - z, 0 - 9)

Minus sign (-) and period (.)

4 [User name]

Enter the user name for the POP server or the SMTP server.

Contents of E-mail sent

5 [Password]

Enter the password for the POP server or the SMTP server.

6 [SMTP server port]

Enter the port number of the SMTP server.

(Normally 25)

7 [POP server port]

Enter the port number of the POP server.

(Normally 110)

8 [Submit]

Update the settings.

Example of the E-mail sent when E-mail is set

The following E-mail is sent when the E-mail settings have been established.

f Example: When [MAIL CONTENTS] is set to [SIMPLE] in the [E-mail set up] page

=== Panasonic projector report(CONFIGURE) ===

Projector Type : PT-FRQ50

Serial No : SN1234567

----- E-mail setup data -----

TEMPERATURE WARNING SETUP

MINIMUM TIME at [ 60] minutes interval

INTAKE AIR TEMPERATURE Over [ 46 degC / 114 degF ]

ERROR [ OFF ]

INTAKE AIR TEMPERATURE [ OFF ]

PERIODIC REPORT

Sunday [ OFF ] Monday [ OFF ] Tuesday [ OFF ] Wednesday [ OFF ]

Thursday [ OFF ] Friday [ OFF ] Saturday [ OFF ]

00:00 [ OFF ] 01:00 [ OFF ] 02:00 [ OFF ] 03:00 [ OFF ]

04:00 [ OFF ] 05:00 [ OFF ] 06:00 [ OFF ] 07:00 [ OFF ]

08:00 [ OFF ] 09:00 [ OFF ] 10:00 [ OFF ] 11:00 [ OFF ]

12:00 [ OFF ] 13:00 [ OFF ] 14:00 [ OFF ] 15:00 [ OFF ]

16:00 [ OFF ] 17:00 [ OFF ] 18:00 [ OFF ] 19:00 [ OFF ]

20:00 [ OFF ] 21:00 [ OFF ] 22:00 [ OFF ] 23:00 [ OFF ]

----- Wired network configuration -----

DHCP Client ON

IP address 192.168.0.101

MAC address BC:AD:01:80:AA:05

----- Error information -----

SELF TEST : ERROR

F121 VCM com. error

Wed Dec 01 09:20:44 2021

----- Memo -----

174 - ENGLISH

Chapter 5   Operations — Using the web control function

Example of the E-mail sent for an error

The following E-mail is sent when an error has occurred.

f

Example: When [MAIL CONTENTS] is set to [SIMPLE] in the [E-mail set up] page

=== Panasonic projector report(ERROR) ===

Projector Type : PT-FRQ50

Serial No : SN1234567

----- Wired network configuration -----

DHCP Client ON

IP address 192.168.0.101

MAC address BC:AD:01:80:AA:05

----- Error information -----

SELF TEST : ERROR

F121 VCM com. error

H012 Exhaust air temp. sensor error

Wed Dec 01 09:21:36 2021

----- Memo -----

[User function set up] page

Set the function limitation for the user rights.

Click [Detailed set up] → [User function set up].

1

2

1 [Remote preview lite]

To disable the remote preview lite function with the user rights, set [Disable].

2 [Submit]

Updates the setting.

[Status notification] page

Set the push notification function. A push notification of updated information is sent to the application software linked to the projector, such as the “Multi Monitoring & Control Software”, when there is a change in status, such as occurrence of an error in the projector.

Click [Detailed set up] → [Status notification].

1

2

3

4

1 [Error alert notification]

Set to [ENABLE] to use the push notification function.

2 [Notification IP address]

Enter the IP address of the notification destination.

3 [Notification port]

Enter the port number of the notification destination.

4 [Submit]

Updates the setting.

ENGLISH - 175

Chapter 5   Operations — Using the web control function

[Network security] page

Make settings to protect the projector from external attacks via LAN and unauthorized use.

Click [Detailed set up] → [Network security].

1

2

1 [COMMAND PROTECT]

Make settings for the connection authentication when using the command control function.

[DISABLE]: Connect to the projector in non-protected mode.

Connection authentication is not performed.

[ENABLE]: Connect to the projector in protected mode.

The user name and password of the administrator account are required for the connection authentication.

Note

2 [Submit]

Updates the setting.

If you click [Submit] with [DISABLE] selected in [COMMAND

PROTECT], a confirmation screen will be displayed. Click [OK] on the confirmation screen to update the settings.

f

When [COMMAND PROTECT] is set to [DISABLE], connection authentication is not performed, making it vulnerable to threats on the network. Be aware of the risks before making settings.

f

For details on how to use the command control function, refer to "Control commands via LAN". ( x

page 204)

[Set up password]

[Set up password] page (for administrator account)

Click [Set up password].

1

2

3

4

1 [Administrator]

Used to change the setting of the administrator account.

2 [User]

Used to change the setting of the standard user account.

3 [PJLink]

Used to change the setting of the PJLink account.

4 [Next]

Used to change the setting of the password.

176 - ENGLISH

Chapter 5   Operations — Using the web control function

[Administrator]

The user name and password of the administrator account can be set.

1

2

3

4

1 [Account]

Displays the account to change.

2 [Current]

[User name]:

Enter the user name before the change.

[Password]:

Enter the current password.

3 [New]

[User name]:

Enter the desired new user name. (Up to 16 characters in single byte)

[Password]:

Enter the desired new password. (Up to 16 characters in single byte)

[Password(Retype)]:

Enter the desired new password again.

4 [Change]

Determines the change of password.

Note f

To change the setting of the administrator account, entry of [User name] and [Password] in [Current] is required.

f

When the projector is already registered in application software (such as “Multi Monitoring & Control Software”) which uses the communication control via LAN, communication with the projector will become impossible if the user name or password for [Administrator] is changed. If the user name or password for [Administrator] is changed, update the registration information of the application software in use.

[User]

The user name and password of the standard user account can be set.

1

2

3

1 [Account]

Displays the account to change.

2 [New]

[User name]:

Enter the desired new user name. (Up to 16 characters in single byte)

[Password]:

Enter the desired new password. (Up to 16 characters in single byte)

[Password(Retype)]:

Enter the desired new password again.

3 [Change]

Determines the change of password.

ENGLISH - 177

Chapter 5   Operations — Using the web control function

[PJLink]

The password of the PJLink account can be changed.

1

2

3

1 [Account]

Displays the account to change.

2 [New]

[Password]:

Enter the desired new password. (Up to 32 characters in single byte)

3 [Change]

Determines the change of password.

[Set up password] (for standard user account)

The password of the standard user account can be changed.

3

4

1

2

1 [Old Password]

Enter the current password.

2 [New Password]

Enter the desired new password. (Up to 16 characters in single byte)

License download page

3 [Retype]

Enter the desired new password again.

4 [Change]

Determines the change of password.

1

1 [Download]

The license for the open source software used in the projector is downloaded by clicking this item. Specify the destination to save and download the license.

Note f

Provided license is a text file, and it is saved in the firmware of the projector in zip format compressed file.

File name: License.zip

178 - ENGLISH

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents