Using the data cloning function. Panasonic PT-FRQ60BU7, PT-FRQ60WU7

Add to my manuals
221 Pages

advertisement

Using the data cloning function. Panasonic PT-FRQ60BU7, PT-FRQ60WU7 | Manualzz

Chapter 5   Operations — Using the data cloning function

Using the data cloning function

Perform the operation of the data cloning function. Data such as the settings and adjustment values of the projector can be copied to multiple projectors via LAN or using the USB memory.

r

Data that cannot be copied

The following settings cannot be copied. Set these in each projector.

f

The [PROJECTOR SETUP] menu → [PROJECTOR ID] f

The [PROJECTOR SETUP] menu → [BRIGHTNESS CONTROL] f The [PROJECTOR SETUP] menu → [DATE AND TIME] → [ADJUST CLOCK] f The [PROJECTOR SETUP] menu → [DATA CLONING] → [LAN] → [WRITE PROTECT] f

The [SECURITY] menu → [SECURITY PASSWORD] f

The [SECURITY] menu → [CONTROL DEVICE SETUP] f

The [NETWORK] menu → [WIRED LAN] f

The [NETWORK] menu → [WIRELESS LAN] f

The [NETWORK] menu → [PROJECTOR NAME] f

The [NETWORK] menu → [NETWORK SECURITY] f Security password f Control device password f

Password set in “[Set up password] page (for administrator account)” ( x

page 176) of the web control screen f

Information of the CRT key and the self-signed certificate generated in “[Certificate] page” ( x

page 165) of the web control screen, information of the installed server certificate f

“[Network security] page” ( x

page 176) in the web control screen f

“[E-mail set up] page” ( x

page 173) in the web control screen f

“[Authentication set up] page” ( x

page 174) in the web control screen f

“[Crestron Connected] page” ( x

page 171) in the web control screen r

Supported device

f

Commercially available USB memory is supported.

The USB memory with a security function is not supported.

f

Only the cards formatted in FAT16 or FAT32 can be used.

f

Only the single partition structure is supported.

Note f

The data cloning function will not operate when the models of the projectors are different. For example, data of PT-FRQ50 can be copied to other PT-FRQ50 projectors, but it can not be copied to PT-FRQ60. Data cloning is limited to the same model.

Copying the data to another projector via LAN

Make the following settings on the projector of the copy destination in advance. For details, refer to “Setting [WRITE

PROTECT]” ( x page 180).

f

The [PROJECTOR SETUP] menu → [DATA CLONING] → [LAN] → [WRITE PROTECT] → [OFF]

Note f

To use the network function with the projector, it is necessary to set the password of the administrator account. ( x

page 141)

When a password is not set for the administrator account (when blank), the network function of the projector cannot be used. To copy the data via LAN, set the passwords for the copy source projector and the copy destination projector.

1) Connect all projectors to a switching hub using LAN cables. ( x

page 149)

2) Turn on all the projectors.

3) Press as

to select [DATA CLONING] on the copy source projector.

4) Press the <ENTER> button.

f

The [SECURITY PASSWORD] screen is displayed.

5) Enter a security password and press the <ENTER> button.

f

The [DATA CLONING] screen is displayed.

6) Press as to select [LAN].

ENGLISH - 179

Chapter 5   Operations — Using the data cloning function

7) Press the <ENTER> button.

f

The [LAN DATA CLONING] screen is displayed.

8) Press as to select [SELECT PROJECTOR].

9) Press the <ENTER> button.

f The projectors in the same subnet are displayed as a list.

10) Press as

to select the copy destination projector.

11) Press the <ENTER> button.

f

To select multiple projectors, repeat Steps 10) to 11) .

12) Press the <DEFAULT> button on the remote control.

f

The confirmation screen is displayed.

13) Press qw

to select [OK], and press the <ENTER> button.

f

Copy of the data between the projectors is started.

Once the copy is completed, results are displayed as a list in the [LAN DATA CLONING] screen.

Meanings of the marks displayed in the list are as follows.

g

Green: Data copy has succeeded.

g Red: Data copy has failed. Confirm the connection of the LAN cable and power status of the copy destination projector.

f Data is copied to the copy destination projector in the standby mode.

If the copy destination projector is in the projection mode, the LAN data cloning request message is displayed, and then the copy destination projector automatically shifts to the standby mode to start copy of data.

14) Turn on the copy destination projector.

f The copied content is reflected to the projector.

Note f

The security password is the password set in the [SECURITY] menu → [SECURITY PASSWORD CHANGE].

Initial password of the factory default setting: awsqawsq f

The light source indicator <LIGHT> and the temperature indicator <TEMP> of the copy destination projector blink while copying the data.

Confirm that the blinking of the indicators stops, and then turn on the projector.

Setting [WRITE PROTECT]

Set if the copy of data via LAN is permitted or not.

1) Press as

to select [DATA CLONING] on the copy destination projector.

2) Press the <ENTER> button.

f

The [SECURITY PASSWORD] screen is displayed.

3) Enter a security password and press the <ENTER> button.

f

The [DATA CLONING] screen is displayed.

4) Press as

to select [LAN].

5) Press the <ENTER> button.

f

The [LAN DATA CLONING] screen is displayed.

6) Press as

to select [WRITE PROTECT].

7) Press qw

to switch the item.

f The items will switch each time you press the button.

[OFF]

[ON]

Permits operations of [DATA CLONING] from another projector via LAN.

Does not permit the operations of [DATA CLONING] from another projector via LAN.

f

Data copy will not be possible when [ON] is set. When it is not necessary to copy data, set [ON] so that the data is not changed by mistake.

180 - ENGLISH

Chapter 5   Operations — Using the data cloning function

Note f

The security password is the password set in the [SECURITY] menu → [SECURITY PASSWORD CHANGE].

Initial password of the factory default setting: awsqawsq

Copying the data to another projector using USB

Copying projector data to USB memory

1) Insert the USB memory into the <USB (DC OUT)> terminal.

2) Press as

to select [DATA CLONING].

3) Press the <ENTER> button.

f

The [SECURITY PASSWORD] screen is displayed.

4) Enter a security password and press the <ENTER> button.

f

The [DATA CLONING] screen is displayed.

5) Press as

to select [USB MEMORY].

6) Press the <ENTER> button.

f

The [SELECT COPY TYPE] screen is displayed.

7) Press as

to select [PROJECTOR -> USB MEMORY].

8) Press the <ENTER> button.

f The confirmation screen is displayed.

9) Press qw

to select [OK], and press the <ENTER> button.

f Copying of data to the USB memory is started.

Once the copying of data is completed, [Data copy finished.] is displayed.

10) Once the copying of the data is completed, disconnect the USB memory from the <USB (DC OUT)> terminal.

Note f

The security password is the password set in the [SECURITY] menu → [SECURITY PASSWORD CHANGE].

Initial password of the factory default setting: awsqawsq f

For the USB memory that can be used with the projector and handling of the memory, refer to “Using the USB memory” ( x

page 55).

f

An error message is displayed when saving or reading data to/from the USB memory has failed.

Copying data in the USB memory to the projector

1) Insert the USB memory into the <USB (DC OUT)> terminal.

2) Press as to select [DATA CLONING].

3) Press the <ENTER> button.

f The [SECURITY PASSWORD] screen is displayed.

4) Enter a security password and press the <ENTER> button.

f The [DATA CLONING] screen is displayed.

5) Press as

to select [USB MEMORY].

6) Press the <ENTER> button.

f

The [SELECT COPY TYPE] screen is displayed.

7) Press as

to select [USB MEMORY -> PROJECTOR].

8) Press the <ENTER> button.

f

The confirmation screen is displayed.

9) Press qw

to select [OK], and press the <ENTER> button.

f The projector automatically enters standby state and starts copying data from the USB memory to the projector.

ENGLISH - 181

Chapter 5   Operations — Using the data cloning function

10) Once the copying of the data is completed, disconnect the USB memory from the <USB (DC OUT)> terminal.

11) Turn on the power of the projector.

f

The copied content is reflected to the projector.

Note f

The security password is the password set in the [SECURITY] menu → [SECURITY PASSWORD CHANGE].

Initial password of the factory default setting: awsqawsq f

The light source indicator <LIGHT> and the temperature indicator <TEMP> of the copy destination projector blink while copying the data.

Confirm that the blinking of the indicators stops, and then turn on the projector.

182 - ENGLISH

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents