Mounting top link fork. Krone BA EasyCut F 320 CV, BA EasyCut F 320 CV gez./ges.

Add to My manuals
154 Pages

advertisement

Mounting top link fork. Krone BA EasyCut F 320 CV, BA EasyCut F 320 CV gez./ges. | Manualzz

7

7.3

Start-up

Mounting top link fork

For the “trailed” version

„ Check distance (A) and distance (+B/-B).

ð Distance (A)=900 mm

ð Distance (-B) (hidden lower link point)=180 mm

„ Change the front lifting unit over to single-acting.

„ Disconnect the lower links from the swing position.

„ Move the front axle suspension of the tractor to the central position and deactivate it.

7.3

Mounting top link fork

For the “pushed” version

2 4

3

7.4

1

3

KMG000-062

INFO

The top link fork (1) can be ordered with the order number 20 433 452 0.

„ Screw the top link fork (1) into the top link (2) M30 x 3.5.

Alternatively, it is also possible to use a telescopic top link instead of a top link.

„ Fit the forks (3) below the straight side onto the top link fork.

„ Mount the top link fork with the rounded side (4) facing upwards on the tractor side.

„ Perform a visual inspection to check that the forks (3) are pointing downwards and the rounded off side (4) of the top link fork is pointing upwards.

Connecting machine to tractor

WARNING

Risk of injury due to unexpected movement of the machine

During the connecting/decoupling process of the front mounted mower, the machine may start to move unexpectedly and may therefore result in injury.

„ Only one person may carry out the connecting/decoupling process.

„ Make sure there is nobody in the danger zone during the connecting/decoupling process.

„ Stop the connecting/decoupling process immediately if there is somebody in the danger zone.

64

EasyCut F 320 CV

Original operating instructions 150000173_09_en-GB

Start-up

Connecting machine to tractor

7

7.4

NOTICE

When attaching implements at the front and rear, the permitted total weight, the permitted axle loads and the tyre load capacity of the tractor must not be exceeded. Even with an implement mounted at the rear, the front axle of the tractor must always be loaded with at least 20% of the tare weight of the tractor.

„ Prior to starting the trip, ensure that these conditions are met,

see Page 60 .

KMG000-049

WARNING! Increased risk of injury! Nobody is allowed to be between tractor and machine during the connecting process (especially when the tractor is moving forward).

„ Lower the front linkage hydraulically until the lower links (1) of the tractor are below the lower link pins of the machine.

„ Advance the tractor forward up to the machine.

„ Raise the front linkage hydraulically until the lower links (1) engage in the ball sleeves and lock.

„ Switch off the tractor, remove the ignition key and take it with you.

„ Secure the tractor against rolling away.

„ Engage the top link (2) at the three-point hitch, and secure it.

For "Relief springs" version

„

Mount relief springs, see Page 67

.

Check clearance

NOTICE

Damage to the machine because the clearance is too small

If the clearance between the front wheels of the tractor and the machine is too low, the machine may be damaged during use.

„ Check the clearance between the front wheels of the tractor and the machine after placing the machine in service the first time and whenever changing the tractor wheels.

„ Check the clearance of the front wheels at all steering angles. If the guards or swath flaps come into contact with the front wheels of the tractor, mount the lower link extensions

between the lower links and the coupling triangle, see Page 66 .

EasyCut F 320 CV

Original operating instructions 150000173_09_en-GB 65

advertisement

Related manuals

advertisement

Table of contents