Waste disposal. Krone BA EasyCut F 320 CV, BA EasyCut F 320 CV gez./ges.

Add to My manuals
154 Pages

advertisement

Waste disposal. Krone BA EasyCut F 320 CV, BA EasyCut F 320 CV gez./ges. | Manualzz

17

Waste disposal 17

Waste disposal

After the service life of the machine has expired, the individual components of the machine must be disposed of properly. The currently applicable country-specific waste disposal guidelines and the relevant laws must be observed.

Metal parts

• All metal parts must be taken to a metal recycling centre.

• Before scrapping, remove operating fluids and lubricants (e.g. gear oil, oil from the hydraulic system) from the components.

• The operating fluids and lubricants must be taken separately to an environmentally friendly disposal point or recycling centre.

Operating fluids and lubricants

• Operating fluids and lubricants (e.g. diesel fuel, coolant, gearbox oil, oil from hydraulic system) must be taken to a waste oil disposal point.

Synthetic materials

• All synthetic materials must be taken to a recycling centre for synthetic materials.

Rubber

• All rubber parts (e.g. hoses, tyres) must be taken to a rubber recycling centre.

Electronic components

• All electronic components must be taken to a disposal point for electronic scrap.

EasyCut F 320 CV

Original operating instructions 150000173_09_en-GB 147

Index

A

Adapting coupling points .................................... 56

Adapting universal shaft ..................................... 54

Additional equipment and spare parts ................ 14

Adjusting the relief spring(s) ............................... 97

Airborne noise emission ..................................... 49

Ambient temperature .......................................... 50

Applicable documents .......................................... 7

Area output ......................................................... 49

Attaching the relief springs with a turnbuckle ..... 68

B

Basic safety instructions ..................................... 13

Basic setting of mower ....................................... 77

Behavior in the case of voltage flashover of

overhead lines .................................................... 21

Behaviour in dangerous situations and in case of

accidents ............................................................ 24

148

EasyCut F 320 CV

Original operating instructions 150000173_09_en-GB

Index

C

Calculating the ballasting of the tractor-machine

combination ........................................................ 60

Carrying out oil level check and oil and filter

element changes safely...................................... 25

Changing the oil ............................... 123, 125, 126

Check clearance................................................. 65

Check/change blades ....................................... 130

Check/replace cutting discs/mower drums ....... 139

Check/replace retaining bolts ........................... 134

Checking drive belt for damage........................ 119

Checking front end dimension ............................ 75

Checking guard cloths ...................................... 115

Checking hydraulic hoses ................................ 121

Checking impact stops on the cutterbar ........... 139

Checking internal chains for overstretching ....... 69

Checking locking device and latch ..................... 76

Checking oil level ............................................. 141

Checking the tines on the tine conditioner ......... 76

Checking/replacing the blade carrier ................ 136

Checking/setting belt tension ........................... 118

Checking/setting parallel lifting ........................... 66

Checklist for initial operation .............................. 53

Checklist for the transport of the machine .......... 93

Children in danger .............................................. 14

Cleaning the machine....................................... 116

Closing/opening the stop cock ........................... 84

Commissioning ................................................... 53

Configure/check the Camera Monitor System.. 104

Connect the Camera Monitor System ................ 73

Connecting hydraulic hoses ............................... 70

Connecting machine to tractor ........................... 64

Connecting road travel lighting ........................... 71

Connecting the machine..................................... 14

Consumables ............................................... 20, 50

Contact ................................................................. 2

Contact data of your dealer .................................. 2

Contamination of hydraulic system and/or fuel

system ................................................................ 20

Control and Display Elements ............................ 52

Conversion table ................................................ 10

EasyCut F 320 CV

Original operating instructions 150000173_09_en-GB

Cross references .................................................. 8

Cutting height...................................................... 49

D

Damaged hydraulic hoses .................................. 22

Danger associated with welding work................. 24

Danger resulting from damage to the machine... 15

Danger when cornering with a hitched machine

and due to the overall width................................ 19

Danger when driving on road and field ............... 19

Danger zone between tractor and machine........ 17

Danger zone due to trailing machine parts ......... 17

Danger zone ejected objects .............................. 17

Danger zone PTO shaft ...................................... 17

Danger zone universal shaft ............................... 16

Danger zone when drive is switched on ............. 17

Danger zones ..................................................... 16

Dangers arising from environment...................... 21

Dangers during road travel ................................. 19

Dangers if the machine is not prepared properly for

road travel ........................................................... 19

Dangers in connection with certain activities:

Working on the machine ..................................... 23

Dangers when operating the machine on slopes 20

Declaration of conformity .................................. 153

Deviating tightening torques ............................. 112

Dimensions ......................................................... 49

Directories and references.................................... 7

Dismounting/mounting guard ............................ 116

Drive belt........................................................... 116

Driving and Transport ......................................... 89

E

Ensuring functionality of safety devices.............. 18

Environmental protection and disposal............... 21

149

Index

F

Field mode.......................................................... 87

Figures ................................................................. 8

Fire hazard ......................................................... 21

Fold down the front guard .................................. 80

Folding down the side guard - for "Series" version

(working position) ............................................... 81

Folding down the side guard – in version

"hydraulically folding side guards" (working

position) .............................................................. 83

Folding up the front guard .................................. 79

Folding up the side guard - for "Series" version

(transport position) ............................................. 81

Folding up the side guard – in version

"hydraulically folding side guards" (transport

position) .............................................................. 82

Front guard ......................................................... 79

G

General disturbances ....................................... 146

H

Hot liquids........................................................... 22

Hot surfaces ....................................................... 23

How to use this document .................................... 7

Hydraulic control units of the tractor ................... 52

Hydraulic oil ...................................................... 121

150

I

Icons in figures...................................................... 9

Icons in the text..................................................... 8

Importance of operating instructions................... 13

Increasing/reducing ground pressure via

perforated bars ................................................... 97

Increasing/reducing ground pressure via

supporting chains................................................ 98

Increasing/reducing ground pressure via

turnbuckles ......................................................... 98

Increasing/reducing ground pressure – mechanical

relief adjustment ................................................. 99

Increasing/reducing the soil pressure - for version

with “hydraulic relief adjustment” ...................... 100

Information for enquiries and orders ..................... 2

Information labels on the machine...................... 35

Information on direction ........................................ 8

Information on This Document.............................. 7

Input gearbox .................................................... 123

Installing universal shaft ..................................... 74

Intended use ....................................................... 12

Intermediate universal shaft................................ 48

J

Jobs on the machine........................................... 15

L

Labelling ............................................................. 47

Lashing the machine........................................... 94

Lifting the machine.............................................. 93

Liquids under high pressure ............................... 22

Location and meaning of the information signs .. 36

Location and meaning of the safety signs .......... 28

Locking screws on the gearboxes .................... 112

Lower link pins .............................................. 56, 58

Lowering machine from transport position to

working position .................................................. 85

Lubricate universally-jointed drive shaft............ 144

Lubricating greases ............................................ 51

Lubricating intermediate universal shaft ........... 144

Lubricating universal shaft ................................ 144

Lubrication chart – Machine.............................. 145

EasyCut F 320 CV

Original operating instructions 150000173_09_en-GB

Index

M

Machine Description ........................................... 45

Machine equipment ............................................ 50

Machine overview............................................... 45

Main gearbox.................................................... 125

Maintenance – After the season....................... 108

Maintenance – Before the season.................... 107

Maintenance - Cutterbar................................... 127

Maintenance - Every 10 hours, but at least once a

day.................................................................... 109

Maintenance - Every 200 hours ....................... 109

Maintenance - Every 50 hours ......................... 109

Maintenance - Gearbox .................................... 122

Maintenance - General Information .................. 107

Maintenance - Hydraulic System...................... 120

Maintenance – Lubrication ............................... 143

Maintenance - Once after 50 hours .................. 109

Maintenance and repair work ............................. 23

Maintenance table ............................................ 107

Malfunction, cause and remedy ....................... 146

Means of representation....................................... 8

Metric thread screws with control thread .......... 109

Metric thread screws with countersunk head and

hexagon socket ................................................ 111

Metric thread screws with fine thread ............... 110

Mounting lighting system .................................... 55

Mounting lower link extension ............................ 66

Mounting relief springs ....................................... 67

Mounting the universal shaft on the machine ..... 55

Mounting top link fork ......................................... 64

Moving support jack into support position .......... 84

Moving support jack into transport position ........ 83

N

Noise may damage your health.......................... 22

Notices with information and recommendations. 10

O

Oils...................................................................... 51

Only perform work when the machine is at

standstill .............................................................. 23

Operating support jack........................................ 83

Operating the Camera Monitor System .............. 88

Operating the stop cock ...................................... 85

Operation ............................................................ 79

Operation only after proper commissioning ........ 15

Operational safety: Technically sound condition 15

Overload protections on the machine ................. 47

Overview of gearboxes ..................................... 122

P

Parking the machine ........................................... 90

Parking the machine safely................................. 20

Passengers ......................................................... 15

Performing a visual inspection .......................... 121

Personal protective equipment ........................... 18

Personnel qualification of the operating personnel

............................................................................ 13

Personnel qualification of the technicians........... 14

Preparing the machine for road travel ................ 89

Preparing the machine for shipment ................... 92

Preparing tractor ................................................. 63

R

Raised machine and machine parts ................... 23

Raising machine from working position to transport

position ............................................................... 86

Reasonably foreseeable misuse......................... 12

Re-ordering ........................................................... 7

Replacing drive belt .......................................... 119

Replacing the shear bolt at the rotary hub........ 129

Requirements for the tractor – electrics .............. 50

Requirements for tractor - power ........................ 50

Road safety......................................................... 19

Rotary hub ........................................................ 128

EasyCut F 320 CV

Original operating instructions 150000173_09_en-GB 151

Index

S

Safety ................................................................. 12

Safety features ................................................... 43

Safety routines ................................................... 24

Safety sign on the machine .......................... 19, 26

Scope of the document ........................................ 8

Securing raised machine and machine parts

against lowering ................................................. 25

Service life of the machine ................................. 13

Setting conditioner speed ................................. 102

Setting swath width .......................................... 103

Setting the cutting height .................................... 95

Setting the degree of conditioning .................... 102

Setting the side guards..................................... 101

Setting wide spreading ..................................... 104

Settings .............................................................. 95

Shutting down and safeguarding the machine ... 24

Side guard - for the “series” version ................... 80

Side guard - for version with “hydraulically folding

side guards”........................................................ 82

Significance of the document ............................... 7

Sources of danger on the machine .................... 22

Start-up............................................................... 60

Structural modifications on the machine ............ 14

T

Target group of this document ............................. 7

Technical data .................................................... 49

Technical limit values ......................................... 16

Technically permitted maximum speed (road

travel) ................................................................. 49

Technically sound state of the machine ............. 15

Telescopic top link .............................................. 96

Tensioning/relieving belt drive .......................... 117

Term “machine” .................................................... 8

Tightening guard cloth ........................................ 74

Tightening torques............................................ 109

Top link pin ................................................... 57, 58

Tractor requirements – hydraulics ...................... 50

U

universal shaft..................................................... 54

Unsuitable consumables..................................... 20

V

Validity .................................................................. 7

Venting the friction clutch.................................. 113

W

Warning signs ....................................................... 9

Warnings of property damage/environmental

damage ............................................................... 10

Waste disposal ................................................. 147

Weights ............................................................... 49

Working at or on heights of the machine ............ 23

152

EasyCut F 320 CV

Original operating instructions 150000173_09_en-GB

18

Declaration of conformity 18

Declaration of conformity

UKCA Declaration of Conformity

We

KRONE Agriculture SE

Heinrich-Krone-Straße 10, D-48480 Spelle hereby declare, as manufacturer of the product named below, under our sole responsibility, that the

Machine:

Type:

Front mounted mowers

EasyCut F 320 CV to which this declaration refers is in compliance with the following relevant provisions of:

• Supply of Machinery (Safety) Regulations 2008, 2008 No. 1597

The signing Managing Director is authorised to compile the technical documents.

Spelle, 04/08/2021

Year of manufacture:

Importer and authorised representative:

Krone UK Ltd.

Phoenix Avenue

Micklefield, Leeds LS25 4DY

Jan Horstmann

(Managing Director, Design & Development)

Machine no.:

EasyCut F 320 CV

Original operating instructions 150000173_09_en-GB 153

Maschinenfabrik

Bernard Krone GmbH & Co. KG

* Heinrich-Krone-Straße 10

D-48480 Spelle

* Postfach 11 63

D-48478 Spelle

' +49 (0) 59 77 / 935-0

6 +49 (0) 59 77 / 935-339

ü

www.landmaschinen.krone.de

advertisement

Related manuals

advertisement

Table of contents