Advertisement
Advertisement
Characteristics
At a Glance
Subject of this chapter
What's in this
Chapter?
This chapter gives the product characteristics.
This chapter contains the following sections:
Section
4.1
4.2
4.3
4.4
Topic
Control Box specifications
Characteristics of the front panels
Environmental characteristics
Limitations on use
4
Page
08/2006
41
Characteristics
4.1
Control Box specifications
At a Glance
Subject of this
Section
What's in this
Section?
This section specifies the characteristics of the Control Boxes.
This section contains the following topics:
Topic
Characteristics of MPC DN• •••• ••• products
Characteristics of MPC EN• •••• ••• products
Page
42
08/2006
Characteristics
Characteristics of MPC DN• •••• ••• products
Introduction
Control Box
Characteristics
The characteristics of the MPC DN• •••• ••• products differ from model to model.
These are given below according to product reference.
Characteristics:
Component
Hard disk
RAM
CD-ROM drive
Floppy Disk drive
Video card
Extension slots
Input/Output ports
Dimensions
Weight
Decription
≥
40 GB IDE - 2.5 "
SDRAM 512 Mb extensible up to 2 Gb (2 slots memory maximum)
24 x speed or combo drive of DVD reader or CD writer (optional)
3.5 " 1.44 MB (fixed)
64 bit RAM 2 Mb (fixed)
4 x slots PCI bus and 2 slots PCMCIA type I/II (or 1 type III) z 1 x Ethernet TCP/IP port 10BASE-T/100BASE-TX (RJ45 connector) z 2 x USB ports (12 MBit/s) z 1 x COM4 RS 232 serial port (SUB-D male 9-contacts connector) z 1 x COM1 RS 232 serial port (SUB-D male 9-contacts connector) z 1 x bi-directional parallel port (connector type SUB-D female
15-contact connector) z 1 x external VGA video screen port (connector type SUB-D female 15 contacts) z 1 x port for PS/2 keyboard (mini-DIN connection) (1) z 1 x port for PS/2 pointing device (mini-DIN connection) (1)
316 x 310 x 200 mm (12.4 x 12.2 x 7.9 in.)
11.3 kg (24.91 lbs)
(1) The port is not operational if the iPC is connected to a front panel.
08/2006
43
Characteristics
Processor
Power supply
Operating systems
Pre-installed packs
Type of processor according to product reference:
Reference
MPC DN• 2••• •••
MPC DN• 5••• •••
Processor
Celeron M with a clock frequency
≥
1.3 GHz
Pentium M with a clock frequency
≥
1.6 GHz
Power supply of MPC DN• ••A• ••• products (AC):
Supply voltage
Frequency
115...230 VAC - 50/60 Hz, (threshold values: 98...264 VAC)
50/60 Hz (threshold values: 47/63 Hz), EN 61131-2 compliant
Consumption 160 VA
Micro-cuts 10 ms
Power supply of MPC DN• ••D• ••• products (DC):
Supply voltage 24 VDC, (threshold values: 19...32 V)
Consumption 170 W
Micro-cuts 1 ms
The products are delivered with a pre-installed operating system according to the reference ordered.
The products have been tested and are guaranteed with the following operating systems: z z
Microsoft Windows 2000
Microsoft Windows XP Pro
Pre-installed packs according to product reference:
Reference
MPC DN• •••• ••A
MPC DN• •••• ••B
Software
Vijeo Look Run Time
Vijeo Look Build Time
44
08/2006
Characteristics
Characteristics of MPC EN• •••• ••• products
Introduction
Control Box
Characteristics
The characteristics of the MPC EN• •••• ••• products differ from model to model.
These are given below according to product reference.
Characteristics:
Component
Hard disk
RAM
CD-ROM drive
Floppy Disk drive
Video card
Extension slots
Input/Output ports
Dimensions
Weight
Description
≥
40 GB IDE - 2.5 "
SDRAM 512 Mb extensible to 2 Gb (2 slots memory maximum)
24 x speed or combo drive of DVD reader or CD writer (optional)
3.5 ", 1.44 MB (fixed)
64 bit RAM 2 Mb (fixed)
1 x slots PCI bus and 2 slots PCMCIA type I/II (or 1 type III) z 1 x Ethernet TCP/IP port 10BASE-T/100BASE-TX (RJ45 connector) z 2 x USB ports (12 MBit/s) z 1 x COM4 RS 232 serial port (SUB-D male 9-contacts connector) z 1 x COM1 RS 232 serial port (SUB-D male 9-contacts connector) z 1 x bi-directional parallel port (connector type SUB-D female
15-contact connector) z 1 x external VGA video screen port (connector type SUB-D female 15 contacts) z 1 x port for PS/2 keyboard (mini-DIN connection) (1) z 1 x port for PS/2 pointing device (mini-DIN connection) (1)
316 x 310 x 110 mm (12.4 x 12.2 x 4.33 in)
7.5 Kg 16.53 lbs
(1) Port is non operational if the iPC is connected to a front panel.
08/2006
45
Characteristics
Processor
Power supply
Operating systems
Pre-installed packs
Type of processor according to product reference:
Reference
MPC EN• 2••• •••
MPC EN• 5••• •••
Processor
Intel Celeron M with a clock frequency
≥
1.3 GHz
Intel Pentium M with a clock frequency
≥
1.6 GHz
Power supply of MPC EN• ••A• ••• products (AC):
Supply voltage
Frequency
115...230 VAC - 50/60 Hz, (threshold values: 90...264 VAC)
50/60 Hz (threshold values: 47/63 Hz), EN 61131-2 compliant
Consumption 130 VA
Micro-cuts 10 ms
Power supply of MPC EN• ••D• ••• products (DC):
Supply voltage 24 VDC, (threshold values: 18...36 V)
Consumption 140 W
Micro-cuts 1 ms
The products are delivered with a pre-installed operating system according to the reference ordered.
The products have been tested and are guaranteed with the following operating systems: z z
Microsoft Windows 2000
Microsoft Windows XP Pro
Pre-installed packs according to product reference:
Reference
MPC EN• •••• ••A
Software
Vijeo Look Run Time
46
08/2006
Characteristics
4.2
Characteristics of the front panels
Characteristics of the front panels
Introduction The characteristics of the front panels differ from model to model. These are given below.
Characteristics
Reference
MPC NT5•
MPC NA5•
MPC NB5•
Shared characteristics:
Number of colors
Brightness
Infra-red link
Power supply
≥
262,144
200 Cd/m
2
(typical value), adjustable
IrDA Standard
By Control Box unit
Specific characteristics:
Screen type
Screen size
Definition View angle Touch-sensitive
Screen
TFT active matrix
TFT active matrix
15 "
15 "
1024 x 768 Hor. 160 °
Vert. 160 °
1024x768 Hor. 160°
Vert. 160°
Analog resistant
35 million cycles
-
TFT active matrix
15 " 1024x768 Hor. 160 °
Vert. 160 °
Analog resistant
35 million cycles
Keyboard
-
Weight
(Kg)
9.3
IBM standard 70-key alphanumeric
2x10 user function keys
IBM standard 70-key alphanumeric
2x10 user function keys
9.3
9.3
For the front-panel dimensions, please refer to
08/2006
47
Characteristics
4.3
Environmental characteristics
Environmental characteristics
General The environmental characteristics given below are applicable to both the Control
Boxes and the front panels of the products.
Characteristics
Specification
Degree of Protection
Storage temperature
Usage altitude
Storage altitude
Vibration
(in operation)
Shock Resistance
(in operation)
Humidity
Interference immunity
The environmental characteristics are as follows:
Operating- temperature)
Value z z
IP65 for the forward part of the front panels.
IP 20 for the rest of the product
0 to 50 °C (32 to122 °F)
-25 to 60 °C
0...3000 m
0...12000 m
–
(-13 to 140 °F)
(9000 ft max)
(36000 ft max)
Standards
–
In accordance with EN 61131-2, UL 508 for standard location, UL 1604 for Class I,
Division 2 hazardous location.
IEC 68-2-2 Bb and Ab tests,
IEC 68-2-14 Na test and EN 61131-2 compliant
–
–
IEC 68-2-6 Fc test and EN 61131-2 compliant
15 g over 11 ms IEC 68-2-27 Ea test and EN 61131-2 compliant
20 % to 80 % RH @ 40 °C (104 °F) –
High frequency interference
Electromagnetic Emissions
Human and material safety
EN 61131, IEC 1000-4-3/6 level 3
Class A/EN 55022/55011
EN 61131-2, UL/CSA and IEC 529/IEC 950
48
08/2006
Characteristics
4.4
Limitations on use
Limitations
At a Glance
CD reader
Combo drive
USB Interfaces
The limitations given below are applicable to the products equipped with CD-reader/
Combo drive devices and also for USB Interfaces.
The CD reader has a maximum operating shock value of 0.2 GHz and a maximum operating vibration value of 5 GHz. Operating the drive outside these limits may cause the drive to function incorrectly.
The combo drive has a maximum operating shock value of 0.2 GHz and a maximum operating vibration value of 5 GHz. Operating the drive outside these limits may cause the drive to function incorrectly.
The ambient operating temperature for the Combo drive is 45 °C + 0 ° - 5 °C.
Operating the drive outside these limits may cause the drive to function incorrectly.
USB ports are intended to connect to especially low consumption devices
(keyboard, mouse, pointing devices). If it is intended to connect a power demanding devices (HDD, CD-ROM), the device must provide its own external power.
The USB connector is not a latching type and so this type of connection is only permissible inside hazardous locations, if means can be provided, preventing mechanically, any accidental disconnection.
Limitations context PCMCIA cards
With the default configuration, two 16-bit mode PCMCIA cards cannot be used at the same time. If necessary, the COM4 serial port can be disabled in order to use two
16-bit mode PCMCIA cards.
08/2006
49
Characteristics
Disabling COM4 port procedure
The procedure for disabling the COM4 port is as follows in the BIOS menu:
1 APIC disabled: Advanced BIOS Features APIC Mode Disabled
2
Phoenix - AwardBIOS CMOS Setup Utility
Advanced CMOS Features
CPU Feature
Hard Disk Boot Priority
CD-ROM Boot Priority
Virus Warning
CPU L1 & L2 Cache
Quick Power On Self Test
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Swap Floppy Drive
Boot Up Floppy Disk
Boot Up NumLock Status
Gate A20 Option
Typematic Rate Setting
Typematic Rate (Chars/Sec)
Typematic Delay (Msec)
Security Option
APIC Mode
[Press Enter]
[Press Enter]
[Press Enter]
[Disabled]
[Enabled]
[Enabled]
[Hard Disk]
[Hard Disk]
[LS120]
[Enabled]
[Disabled]
[Enabled]
[On]
[Fast]
[Disabled]
6
250
[Setup]
[Disabled]
Item Help
Menu Level
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
COM4 disabled: Integrated Peripherals
Port 4 Disabled
Super IO Device Onboard Serial
Phoenix - AwardBIOS CMOS Setup Utility
Super IO Device
Onboard FDC Controller
Onboard Serial Port 1
UART Mode Select
UR2 Duplex Mode
Onboard Parallel Port
Parallel Port Mode
Typematic Rate (Chars/Sec)
Onboard Serial Port 3
Serial Port 3 use IRQ
Onboard Serial Port 4
Serial Port 4 use IRQ
[Enabled]
[3F8/IRQ4]
[IrDA]
[Half]
[378/IRQ7]
[SPP]
3
[3E8]
[IRQ10]
[Disabled]
[IRQ11]
Item Help
Menu Level
50
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
08/2006
08/2006
Characteristics
3 IRQ 9/11 reserved: PnP/PCI Configurations
[Manual] IRQ Resources
Resources Controlled By
IRQ 9/11 assigned to Reserved
Phoenix - AwardBIOS CMOS Setup Utility
PnP/PCI Configurations
Reset Configuration Data
Resources Controlled by
IRQ Resources
[Disabled]
[Manual]
[Press Enter]
PCI/VGA Palette Snoop [Disabled]
Item Help
Menu Level
BIOS can automatically configure all the boot and Plug and Play compatible device.
If you choose Auto, you cannot select IRQ
DMA and memory base address fields, since
BIOS automatically assigns them
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Phoenix - AwardBIOS CMOS Setup Utility
IRQ Resources
IRQ-3 assigned to
IRQ-4 assigned to
IRQ-5 assigned to
IRQ-7 assigned to
IRQ-9 assigned to
IRQ-10 assigned to
IRQ-11 assigned to
IRQ-12 assigned to
IRQ-14 assigned to
IRQ-15 assigned to
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[Reserved]
[PCI Device]
[Reserved]
[PCI Device]
[PCI Device]
[PCI Device]
Item Help
Menu Level
Legacy ISA for devices compliant with the original PC AT bus specification, PCI/ISA
PnP for devices compliant with the
Plug and Play standard whether designed for
PCI or ISA bus architecture
4
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Save the modifications by pressing F10 .
51
Characteristics
Enabling COM4 port procedure
The procedure for enabling the COM4 port is as follows in the BIOS menu:
1 APIC enabled: Advanced BIOS Features APIC Mode Enabled
2
Phoenix - AwardBIOS CMOS Setup Utility
Advanced CMOS Features
CPU Feature
Hard Disk Boot Priority
CD-ROM Boot Priority
Virus Warning
CPU L1 & L2 Cache
Quick Power On Self Test
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Swap Floppy Drive
Boot Up Floppy Disk
Boot Up NumLock Status
Gate A20 Option
Typematic Rate Setting
Typematic Rate (Chars/Sec)
Typematic Delay (Msec)
Security Option
APIC Mode
[Press Enter]
[Press Enter]
[Press Enter]
[Disabled]
[Enabled]
[Enabled]
[Hard Disk]
[Hard Disk]
[LS120]
[Enabled]
[Disabled]
[Enabled]
[On]
[Fast]
[Disabled]
6
250
[Setup]
[Enabled]
Item Help
Menu Level
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
COM4 enabled: Integrated Peripherals
Port 4 2E8
Super IO Device Onboard Serial
Phoenix - AwardBIOS CMOS Setup Utility
Super IO Device
Onboard FDC Controller
Onboard Serial Port 1
UART Mode Select
UR2 Duplex Mode
Onboard Parallel Port
Parallel Port Mode
Typematic Rate (Chars/Sec)
Onboard Serial Port 3
Serial Port 3 use IRQ
Onboard Serial Port 4
Serial Port 4 use IRQ
[Enabled]
[3F8/IRQ4]
[IrDA]
[Half]
[378/IRQ7]
[SPP]
3
[3E8]
[IRQ10]
[2E8]
[IRQ11]
Item Help
Menu Level
52
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
08/2006
08/2006
Characteristics
3 IRQ 9/11 auto: PnP/PCI Configurations
[Auto(ESCD)]
Resources Controlled By
Phoenix - AwardBIOS CMOS Setup Utility
PnP/PCI Configurations
Reset Configuration Data [Disabled]
Resources Controlled by
IRQ Resources
[Auto(ESCD)]
Press Enter
PCI/VGA Palette Snoop [Disabled]
Item Help
Menu Level
BIOS can automatically configure all the boot and Plug and Play compatible device.
If you choose Auto, you cannot select IRQ
DMA and memory base address fields, since
BIOS automatically assigns them
4
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults
Save the modifications by pressing F10 .
53
Characteristics
54
08/2006

Public link updated
The public link to your chat has been updated.
Advertisement