About your projector. Panasonic PT-LW376

Add to my manuals
146 Pages

advertisement

About your projector. Panasonic PT-LW376 | Manualzz

Chapter 1 Preparation - About your projector

About your projector

Remote control

6

1

2

7

3

4

5

8

9

10

11

12

13

14

15

16

17

18

1 Power < v / b > button ( v standby / b power on)

Sets the projector to the state where the projector is switched off (standby mode). Also starts projection when the power is switched off (standby mode).

2 Input selection buttons (<COMPUTER 1> /

<COMPUTER 2>* 1 / <HDMI 1/2>* 2 / <VIDEO> /

<MEMORY VIEWER/NETWORK>* 1 )

Switches the input signal to project. ( x page 46)

*1 The <COMPUTER 2> button and <MEMORY VIEWER/

NETWORK> button are disabled for PT-LB306.

*2 The <HDMI 1/2> button only functions as HDMI input selection button for PT-LB306.

3 <MENU> button / <RETURN> button / asqw buttons

/ <ENTER> button

Used to navigate through the menu screen. ( x page 55)

The asqw buttons are also used to select characters in the menu screen.

4 <FREEZE> button

Pauses the projected image and mute the audio temporarily. ( x page 50)

5 Number (<1> - <6>) buttons

Used for entering the ID number in a multiple projector environment.

6 Remote control signal transmitter

7 <AUTO SETUP> button

Used to perform automatic adjustment while projecting the image ( x page 50).

8 <MUTE> button

Used to mute the audio. ( x page 49)

9 <AV MUTE> button

Used to turn off the audio and video temporarily.

( x page 49)

10 <DAYLIGHT VIEW> button

Used to correct the image when the projector is used in a bright surroundings. ( x pages 52, 61)

11 <DEFAULT> button

Resets the content of the sub-menu to the factory default.

( x page 56)

12 <ID SET> button

Sets the ID number of the remote control in a multi-projector environment. ( x page 52)

13 <D.ZOOM+> button / <D.ZOOM-> button

Zoom in and out the images. ( x page 51)

14 <VOL +> button / <VOL -> button

Adjusts the volume of the built-in speaker or audio output.

( x page 49)

15 <FUNCTION> button

Specifies a shortcut button for a frequently used operation. ( x page 52)

16 <ID ALL> button

Used to simultaneously control all the projectors with one remote control when using multiple projectors.

( x page 52)

17 <P-TIMER> button

Operates the P-timer function. ( x page 51)

18 <SCREEN ADJ> button

Corrects the distortion of the projected image. ( x page

50)

ENGLISH - 25

Chapter 1 Preparation - About your projector

Attention f Do not drop the remote control.

f Avoid contact with liquids.

f Do not attempt to modify or disassemble the remote control.

f Please observe the following contents that are described on the back of the remote control unit (see the right picture).

g Do not use a new battery together with an old battery.

g Do not use unspecified batteries.

g Make sure the polarities (+ and -) are correct when inserting the batteries.

In addition, please read the contents that are related to batteries in the "Read this first!".

Note

1.Do not use old battery with new one.

2.Do not use batteries other than the

type specified.

3.Be sure the batteries are inserted properly.

f The remote control can be used within a distance of about 7 m (22'11-5/8") if pointed directly at the remote control signal receiver. The remote control can control at angles of up to ± 30 ° vertically and ± 30 ° horizontally, but the effective control range may be reduced.

f If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not operate correctly.

f You can operate the projector by reflecting the remote control signal on the screen. The operating range may differ due to the loss of light caused by the properties of the screen.

3.

确保电池安装正确。 f When the remote control signal receiver is lit with a fluorescent light or other strong light source, the projector may become inoperative. Set the projector as far from the luminous source as possible.

原产地 : 中国

Projector body

Top

1 2

Bottom

3

Side

4 5

Side

7

10

Projection direction

26 - ENGLISH

Front

6

8

Rear

9 6

11 12 3 13 14

Chapter 1 Preparation - About your projector

WARNING

Keep your hands and other objects away from the exhaust vent.

f Keep your hand and face away.

f Do not insert your finger.

f Keep heat-sensitive articles away.

Heated air from the exhaust vent can cause burns, injury, or deformations.

1 Control panel and Indicators ( x page 27)

2 Lamp cover ( x page 125)

The lamp unit is located inside.

3 Security chain hook

Attaches a burglar prevention cable, etc.

4 Focus ring

Adjust the focus.

5 Zoom ring

Adjust the zoom.

6 Adjustable foot

Adjust the projection angle.

7 Intake vent / Air filter cover ( x page 123)

The air filter unit is inside.

Attention f Do not block the intake and exhaust vents of the projector.

r

Control panel and Indicators

8 Remote control signal receiver

9 Projection lens

10 Exhaust vent

11 <AC IN> terminal

Connect the supplied power cord.

12 Security slot

This security slot is compatible with the Kensington security cables.

13 Rear terminals ( x page 28)

14 Speaker

1

2

3

4

5

4

8

6

7

1 Power indicator <ON(G)/STANDBY(R)>

Displays the status of the power.

2 Power < v / b > button ( v Standby / b Power on)

Sets the projector to the state where the projector is switched off (standby mode). Also starts projection when the power is switched off (standby mode).

3 <INPUT> button

Displays the input source menu. ( x page 47)

4 <VOL-> button / <VOL+> button

Adjusts the volume level of the built-in speaker or the audio output. ( x page 49)

5 asqw buttons

Selects an item in the menu screen, changes the setting, and adjusts the level.

Also used to select characters in the menu screen.

The w button can be used as the ENTER button when it does not function as a direction button.

Note

6 Warning indicator <WARNING>

Indicates the abnormal conditions of the projector.

7 <MENU> button

Displays or hides the main menu.

When the sub menu is displayed, pressing it will return to the previous screen.

It can be used as ENTER button when the w button functions as a direction button.

8 <AV MUTE> button

Used to turn off the audio and video temporarily. ( x page

49) f In this manual, the operating procedure of menu screen is described by assuming that the projector is operated with the remote control instead of the control panel.

ENGLISH - 27

Chapter 1 Preparation - About your projector r

Connecting terminals

For PT-LW376, PT-LW336, PT-LB426, PT-LB386 and PT-LB356

1 2 3 4 5 6

7 8 9 10

1 <VARIABLE AUDIO OUT> terminal

This is the terminal to output the audio signal input to the projector.

2 <VIDEO IN> terminal

This is the terminal to input video signals.

3 <COMPUTER 1 IN> terminal

This is the terminal to input RGB, YC signals.

B

C

R

/YP

B

P

R

or Y/C

4 <LAN> terminal

This is the LAN terminal to connect to the network.

5 <HDMI 1 IN> terminal / <HDMI 2 IN> terminal

This is the terminal to input HDMI signals.

6 <USB A (VIEWER/WIRELESS/DC OUT)> terminal

When using the Memory Viewer function, insert the USB memory directly to this terminal. ( x page 95)

Please insert the wireless module (Model No.: AJ-WM50

/ ET-WML100) directly to this terminal when using the wireless LAN function. ( x page 99)

In addition, this terminal can be used for power supply

(DC 5 V, maximum 2 A).

Attention

7 <AUDIO IN 1> terminal

This is the terminal to input audio signals.

8 <AUDIO IN 2> terminal

This is the terminal to input audio signals.

Left input (L) and right input (R) are provided for the

<AUDIO IN 2> terminal.

9 <COMPUTER 2 IN/1 OUT> terminal

This is the terminal to input RGB signals or YC

YP

B

C

R

/

P

R

signals. It can also output the signals input from

<COMPUTER 1 IN> terminal to an external device.

10 <SERIAL IN> terminal

This is the RS-232C compatible terminal to externally control the projector by connecting a computer.

f When a LAN cable is directly connected to the projector, the network connection must be made indoors.

f When the [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] is set to [NORMAL], the <USB A (VIEWER/

WIRELESS/DC OUT)> terminal can supply power even in standby state. If set to [ECO], the <USB A (VIEWER/WIRELESS/DC OUT)> terminal can not supply power in standby state.

f When an external device exceeding the rating (DC 5 V, maximum 2 A) is connected to the <USB A (VIEWER/WIRELESS/DC OUT)> terminal, an error is detected and the power supply will be stopped. At this time, disconnect the external device, cut off the power of the projector and then reconnect the power plug to the outlet.

28 - ENGLISH

For PT-LB306

1 2

Chapter 1 Preparation - About your projector

3 4 5 6

7 8 9

1 <VARIABLE AUDIO OUT> terminal

This is the terminal to output audio signal input to the projector.

2 <VIDEO IN> terminal

This is the terminal to input video signals.

3 <COMPUTER 1 IN> terminal

This is the terminal to input RGB, YP signals.

B

P

R

/YC

B

C

R

or Y/C

4 <MONITOR OUT> terminal

This is the terminal to output the RGB signals to external monitor.

5 <HDMI IN> terminal

This is the terminal to input HDMI signals.

6 <USB B> terminal

For service use.

7 <AUDIO IN 1> terminal

This is the terminal to input audio signals.

8 <AUDIO IN 2> terminal

This is the terminal to input audio signals.

Left input (L) and right input (R) are provided for the

<AUDIO IN 2> terminal.

9 <SERIAL IN> terminal

This is the RS-232C compatible terminal to externally control the projector by connecting a computer.

ENGLISH - 29

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents