Connecting. Panasonic PT-LW376

Add to my manuals
146 Pages

advertisement

Connecting. Panasonic PT-LW376 | Manualzz

Chapter 2 Getting Started - Connecting

Connecting

Before connecting

f Before connecting, carefully read the operating instructions for the external device to be connected.

f Turn off the power switch of the devices before connecting cables.

f Take note of the following points before connecting the cables. Failure to do so may result in malfunctions.

g When connecting a cable to a device connected to the projector or the projector itself, touch any nearby metallic objects to eliminate static electricity from your body before performing work.

g Do not use unnecessarily long cables to connect to a device connected to the projector or to the projector body. The longer the cable, the more it is susceptible to noise. Since using a cable while it is wound makes it act like an antenna, it is more susceptible to noise.

g When connecting cables, connect GND first, then insert the connecting terminal of the connecting device in a straight manner.

f If any connection cable is not supplied with the device, or if no optional cable is available for connection of the device, prepare a necessary system connection cable to suit the device.

f Video signals containing too much jitter may cause the images on the screen to randomly wobble or wafture. In this case, a time base corrector (TBC) must be connected.

f The projector accepts Video signals, Y/C signals and YC

B

C

R

/YP

B

P

R

signals and analog RGB signals

(synchronous signals are TTL level), and digital signal.

f Some computer models or graphics cards are not compatible with the projector.

f When using long cables to connect with each of equipment to the projector, there is a possibility that the image will not be output correctly unless a compensator is used.

f For details on what video signals the projector supports, see “List of compatible signals”. ( x page138)

<COMPUTER 1 IN> terminal pin assignments and signal names

Outside view Pin No.

Signal names

R/P

R

/C

G/Y/Y

B/P

B

GND

GND

GND

GND

Pin No.

Signal names

+5 V

GND

GND

DDC data

HD/SYNC

VD

DDC clock

<COMPUTER 2 IN/1 OUT> terminal pin assignments and signal names

(Only for PT-LW376, PT-LW336, PT-LB426, PT-LB386 and PT-LB356)

Outside view Pin No.

Signal names

R /P

R

/C *1

G/Y/Y *1

B /P

B

GND

GND

GND

GND

Pin No.

*1 Y/C signal input from the <COMPUTER 1 IN> terminal can be output from the <COMPUTER 2 IN/1 OUT> terminal.

Signal names

+5 V

GND

DDC data

HD/SYNC

VD

DDC clock

36 - ENGLISH

Chapter 2 Getting Started - Connecting

<MONITOR OUT> terminal pin assignments and signal names

(Only for PT-LB306)

Outside view Pin No.

Signal names

R/P

R

/C

G/Y/Y

B/P

B

GND

GND

GND

GND

Pin No.

Signal names

GND

HD/SYNC

VD

<HDMI 1 IN> / <HDMI 2 IN> / <HDMI IN> terminal pin assignments and signal names

(<HDMI IN> terminal is available for PT-LB306, <HDMI 1 IN> terminal and <HDMI 2 IN> terminal are available for

PT-LW376, PT-LW336, PT-LB426, PT-LB386 and PT-LB356)

Outside view Pin No.

Pin No.

Even-numbered pins to

Odd-numbered pins to

Signal names

T.M.D.S data 2+

T.M.D.S data 2 shield

T.M.D.S data 2 -

T.M.D.S data 1+

T.M.D.S data 1 shield

T.M.D.S data 1 -

T.M.D.S data 0+

T.M.D.S data 0 shield

T.M.D.S data 0 -

T.M.D.S clock +

Signal names

T.M.D.S clock shield

T.M.D.S clock -

CEC

SCL

SDA

DDC/CEC GND

+5 V

Hot plug detection

Connecting example : AV equipment

Audio equipment

Blu-ray disc player with

HDMI terminal

D-sub/component

Conversion cable

D-SUB - S Video conversion cable (Model No.: ET-ADSV)

S-video cable

Video deck

(TBC built-in)

DVD player DVD player

ENGLISH - 37

Chapter 2 Getting Started - Connecting

Attention f Always use one of the following when connecting a VCR.

- A VCR with built-in time base corrector (TBC).

- A time base corrector (TBC) between the projector and the VCR.

f If nonstandard burst signals are connected, the image may be distorted. In such case, connect the time base corrector (TBC) between the projector and the external devices.

Note f For an HDMI cable, use an HDMI High Speed cable that conforms to HDMI standards. If a cable that does not conform to HDMI standards is used, images may be interrupted or may not be projected.

f This projector does not support the VIERA Link (HDMI) or HDMI CEC (Consumer Electronics Control).

f When the <VARIABLE AUDIO OUT> terminal is connected with cable, the sound will not be output from the built-in speaker.

f When input Y/C signal, the optional D-SUB - S Video Conversion cable (Model No.: ET-ADSV) is required.

Connecting example : Computers

r For PT-LW376, PT-LW336, PT-LB426, PT-LB386 and PT-LB356

Computer

Control computer Computer

Audio equipment

Computer

USB memory/

Wireless module

(Model No.: AJ-WM50 /

ET-WML100)

Control computer

38 - ENGLISH

r For PT-LB306

Computer

Chapter 2 Getting Started - Connecting

Computer

Control computer

Control computer

Audio equipment

Attention f When connecting the projector to a computer or an external device, use the power cord supplied with each device and commercially available shielded cables.

Note f For an HDMI cable, use an HDMI High Speed cable that conforms to HDMI standards. If a cable that does not conform to HDMI standards is used, images may be interrupted or may not be projected.

f This projector does not support the VIERA Link (HDMI) or HDMI CEC (Consumer Electronics Control).

f If you operate the projector using the computer with the resume feature (last memory), you may have to reset the resume feature to operate the projector.

f When the <VARIABLE AUDIO OUT> terminal is connected with cable, the sound will not be output from the built-in speaker.

f Attach the optional wireless module (Model No.: AJ-WM50 / ET-WML100) or USB memory directly to the <USB A (VIEWER/WIRELESS/DC

OUT)> terminal of this projector without using a USB extension cable or USB hub.

f If the video signal from the DVI-D terminal of the external device (such as a computer) is connected to the <HDMI 1 IN> / <HDMI 2 IN> /

<HDMI IN> terminal by using a conversion cable, you need to set the [PROJECTOR SETUP] menu → [AUDIO SETTING] → [AUDIO IN

SELECT] to [AUDIO IN 1] or [AUDIO IN 2] ( x page 81) and input the audio signal to the <AUDIO IN 1> or <AUDIO IN 2> terminal.

ENGLISH - 39

Chapter 3 Basic Operations

This chapter describes basic operations to start with.

40 - ENGLISH

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents