[SECURITY] menu. Panasonic PT-LW376

Add to my manuals
146 Pages

advertisement

[SECURITY] menu. Panasonic PT-LW376 | Manualzz

Chapter 4 Settings - [SECURITY] menu

[SECURITY] menu

On the menu screen, select [SECURITY] from the main menu, and select an item from the sub-menu.

Refer to “Navigating through the menu” ( x page 55) for the operation of the menu screen.

f When the projector is used for the first time

Initial password: 1111

Attention f When you select the [SECURITY] menu and press the <ENTER> button, entering a password is required. Enter the preset password and then continue operations of the [SECURITY] menu.

f When the password has been changed previously, enter the changed password, and press the <ENTER> button.

Note f The entered password is displayed with "  " mark on the screen.

f An error message is displayed on the screen when the entered password is incorrect. Re-enter the correct password.

[PASSWORD]

The [PASSWORD] screen is displayed when the power is turned on, [INITIALIZE ALL] is executed or [INITIALIZE] in the [NETWORK] menu is executed. When the entered password is incorrect, the operation will be restricted to the power standby < v / b > button on the control panel or on the remote control.

1) Press as to select [PASSWORD].

2) Press qw to switch the item.

f The items will switch each time you press the button.

[OFF]

[ON]

Disables the security password entry.

Enables the security password entry.

Note f The [PASSWORD] setting is set to [OFF] by the factory default.

f The security password input when turning on the power is not enabled until turning off the power supply and plugging the power plug into the outlet after setting it to [ON]. If the entered password is incorrect when the power is turned on, the operation will be restricted to the power < v / b > button.

[PASSWORD CHANGE]

Change the security password.

1) Press as to select [PASSWORD CHANGE].

2) Press the <ENTER> button.

f The [NEW] screen is displayed.

3) Press qw and <ENTER> button to input the new password.

f A password of 4 digits must be input.

4) Press as to select [OK], and press the <ENTER> button.

f The [CONFIRM] screen is displayed.

5) Re-enter the password for the confirmation.

6) Press as to select [OK], and press the <ENTER> button.

Note f The entered password is displayed with "

" mark on the screen.

f Change the password periodically and make it hard to guess.

[TEXT DISPLAY]

Overlap the security message (text) over the projecting image.

1) Press as to select [TEXT DISPLAY].

2) Press qw to switch the item.

ENGLISH - 85

Chapter 4 Settings - [SECURITY] menu f The items will switch each time you press the button.

[OFF]

[ON]

Disables the text display.

Enables the text display.

[TEXT CHANGE]

Register or change the displayed text when [TEXT DISPLAY] is set to [ON].

1) Press as to select [TEXT CHANGE].

2) Press the <ENTER> button.

f The [TEXT CHANGE] screen is displayed.

3) Press asqw to select the text, and press the <ENTER> button to enter the text.

4) Press asqw to select [OK], and press the <ENTER> button.

f The text is changed.

f Up to 22 characters can be entered.

[MENU LOCK]

Display the menu by the <MENU> button and set whether or not to enable menu operations.

1) Press as to select [MENU LOCK].

2) Press qw to switch the item.

f The items will switch each time you press the button.

[OFF]

[ON]

Enables menu operations.

Disables menu operations.

Note f

When the entered password is incorrect after setting [MENU LOCK] to [ON], the <MENU> button cannot be operated.

f

The factory default setting or the setting after executing the [PROJECTOR SETUP] menu → [INITIALIZE ALL] is set to [OFF]. Set it to [ON] if necessary.

f

When [MENU LOCK] is set to [ON], the [MENU LOCK PASSWORD] screen is displayed after pressing the <MENU> button. After entering the set menu lock password, the menu operation is enabled. In this case, the menu operation will remain enabled until the projector enters into standby mode.

[MENU LOCK PASSWORD]

Change the menu lock password.

1) Press as to select [MENU LOCK PASSWORD].

2) Press the <ENTER> button.

f The [MENU LOCK PASSWORD] screen is displayed.

3) Press asqw to select the text, and press the <ENTER> button to enter the text.

f Up to 16 characters can be input.

4) Press asqw to select [OK], and press the <ENTER> button.

f To cancel, select [CANCEL].

Attention f The initial password is “AAAA” at the time of purchase or when the [PROJECTOR SETUP] menu → [INITIALIZE ALL] is executed.

f Change the password periodically that is hard to guess.

f To initialize your password, consult your dealer.

[CONTROL DEVICE SETUP]

Enable/disable the button operations on the control panel and the remote control.

1) Press as to select [CONTROL DEVICE SETUP].

2) Press the <ENTER> button.

86 - ENGLISH

Chapter 4 Settings - [SECURITY] menu f The [CONTROL DEVICE SETUP] screen is displayed.

3) Press as to select one item between [CONTROL PANEL] and [REMOTE CONTROLLER].

[CONTROL PANEL] You can set the limitation on the control from the control panel.

[REMOTE CONTROLLER] You can set the limitation on the control from the remote control.

4) Press qw to switch between [ENABLE] and [DISABLE]. f You can set the limitation on the control from the control panel or the remote control.

[ENABLE]

[DISABLE]

Enable the button operations.

Disable the button operations.

f A confirmation screen will be displayed when you change [ENABLE] to [DISABLE], then proceed to Step 5) .

5) Press as to select [OK], and then press the <ENTER> button.

Note f When a button operation is performed on the device set to [DISABLE] , the [PASSWORD] screen is displayed.

To continue operations, enter the security password.

f The [PASSWORD] screen will disappear when there is no operation for approx. 10 seconds.

f If the operations of both [CONTROL PANEL] and [REMOTE CONTROLLER] are set to [DISABLE], the projector cannot be turned off

(cannot enter standby).

f Even when you set button operations on the remote control to be disabled, operations of the <ID ALL> and <ID SET> buttons on the remote control are enabled.

ENGLISH - 87

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents