Projecting. Panasonic PT-MZ680

Add to my manuals
210 Pages

advertisement

Projecting. Panasonic PT-MZ680 | Manualzz

Chapter 3   Basic Operations — Projecting

Projecting

Check the external device connection ( x page 46) and the power cord connection ( x page 52), and turn on the power ( x page 54) to start projection. Select the image to project, and adjust appearance of the projected image.

Selecting the input signal

The input of the image to project can be switched. Method to switch the input is as follows.

f Press the input selection button on the remote control and directly specify the input of the image to project.

f Press the <INPUT SELECT> button on the control panel to display the input selection screen, and select the input to project from the list.

Remote control Control panel

Switching the input directly with the remote control

The input for projection can be switched by directly specifying it with the input selection button on the remote control.

1) Press the input selection button (<HDMI 1>, <HDMI 2>, <HDMI 3>, <COMPUTER>, <DIGITAL LINK>).

<HDMI 1>

<HDMI 2>

<HDMI 3>

<COMPUTER>

<DIGITAL LINK>

Switches the input to HDMI1.

The image of the signal input to the <HDMI IN 1> terminal is projected.

Switches the input to HDMI2.

The image of the signal input to the <HDMI IN 2> terminal is projected.

Switches the input to HDMI3.

The image of the signal input to the <HDMI IN 3> terminal is projected.

Switches the input to COMPUTER.

The image of the signal input to the <COMPUTER IN> terminal is projected.

Switches the input to DIGITAL LINK.

The image of the signal input to the <DIGITAL LINK/LAN> terminal is projected.

Attention f

Images may not be projected properly depending on the external device, or the Blu-ray disc or DVD disc, to be played back.

Set the [PICTURE] menu → [SYSTEM SELECTOR].

f

Confirm the aspect ratio of the projection screen and the image, and switch to an optimum aspect ratio from the [POSITION] menu →

[ASPECT].

Note f

When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the <DIGITAL LINK/

LAN> terminal, the input on the DIGITAL LINK output supported device changes each time the <DIGITAL LINK> button is pressed. The input can also be changed using the RS-232C control command.

For twisted-pair-cable transmitters of other manufacturers, switch the input on the projector to DIGITAL LINK, and then switch the input on the twisted-pair-cable transmitter.

Switching the input by displaying the input selection screen

The input for projection can be selected by displaying the input selection screen using the <INPUT SELECT> button on the control panel.

1) Press the <INPUT SELECT> button on the control panel.

f The input selection screen is displayed.

62 - ENGLISH

Chapter 3   Basic Operations — Projecting

INPUT SELECT

COMPUTER

HDMI1

HDMI2

HDMI3

DIGITAL LINK

ENTER

SELECT

SET

2) Press as to select the input for projection, and press the <ENTER> button.

Note f The input can also be switched by pressing the <INPUT SELECT> button while the input selection screen is displayed.

The input will switch each time you press the <INPUT SELECT> button.

f If the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, the input selection menu for the DIGITAL LINK output supported device is displayed when the <ENTER> button is pressed while the DIGITAL LINK input is selected in the input selection screen.

f If the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, the DIGITAL

LINK logo and the input name selected in the DIGITAL LINK output supported device are displayed in the display section of the [DIGITAL

LINK] in the input selection screen.

Adjusting the focus, zoom, and lens shift

Adjust the focus, zoom, and lens shift if the image projected to the screen or its position is shifted even if the projector and the screen are set up in the correct positions.

Using the control panel

1) Press the <LENS/CANCEL> button on the control panel.

f

Pressing the button changes the adjustment screen in the order of [FOCUS], [ZOOM], and [SHIFT].

2) Select each adjustment item and press asqw to adjust.

Using the remote control

1) Press the lens buttons (<FOCUS>, <ZOOM>, <SHIFT>) on the remote control.

f Pressing the <FOCUS> button: Adjusts the focus (adjustment of the lens focus position).

f Pressing the <ZOOM> button: Adjusts the zoom (adjustment of the lens zoom position).

f Pressing the <SHIFT> button: Adjusts the lens shift (vertical position and horizontal position of the lens).

2) Select each adjustment item and press asqw to adjust.

CAUTION

During the lens shift operation, do not insert your hand in the opening around the lens.

Your hand may get caught, resulting in an injury.

Note f

The adjustment can be performed faster by holding down asqw

for approximately three seconds or longer.

f

It is recommended that images be projected continuously for at least 30 minutes before the focus is adjusted.

f

Only [FOCUS] is displayed in yellow so that the displayed menu item can be recognized by color, even when the displayed characters are unreadable due to incorrect focus. (Factory default)

The displayed color for [FOCUS] differs depending on the setting in the [DISPLAY OPTION] menu → [ON-SCREEN DISPLAY] → [OSD

COLOR].

f

The current position and maximum movable range are displayed with a bar scale during shift adjustment.

Also, the red bar indicates the immovable range from current position.

The triangular mark under the bar scale indicates the home position.

ENGLISH - 63

Chapter 3   Basic Operations — Projecting

Setting the lens type

When the projector is used for the first time or when the projection lens is replaced, confirm the [LENS TYPE] setting. Change the setting if the type does not match the projection lens attached to the projector.

1) Press the <MENU> button.

f The [MAIN MENU] screen is displayed.

2) Press as to select [PROJECTOR SETUP], and press the <ENTER> button.

f The [PROJECTOR SETUP] screen is displayed.

3) Press as to select [LENS], and press the <ENTER> button.

f The [LENS] screen is displayed.

4) Press as

to select [LENS TYPE], and press the <ENTER> button.

f The [LENS TYPE] screen is displayed.

5) Press as

to select the lens type.

[ET-ELS20] *1

[ET-ELW21]

[ET-ELW22]

[ET-ELW20]

[ET-ELT22]

[ET-ELT23]

Select this item when the standard zoom lens or the Zoom Lens (Model No.: ET-ELS20) is attached to the projector.

Select this item when the Fixed-focus Lens (Model No.: ET-ELW21) is attached to the projector.

Select this item when the Zoom Lens (Model No.: ET-ELW22) is attached to the projector.

Select this item when the Zoom Lens (Model No.: ET-ELW20) is attached to the projector.

Select this item when the Zoom Lens (Model No.: ET-ELT22) is attached to the projector.

Select this item when the Zoom Lens (Model No.: ET-ELT23) is attached to the projector.

*1 This product is equivalent to the standard zoom lens.

6) Press the <ENTER> button.

f The [LENS CALIBRATION] screen is displayed.

7) Press qw to select [OK], and press the <ENTER> button.

f The lens calibration is started.

f After completing the calibration, the projection lens will move to the home position.

f To cancel, select [CANCEL]. In this case, the [LENS TYPE] setting is not changed.

Note f

The lens shift range varies depending on the lens type. If [LENS TYPE] is set incorrectly, lens shift range may not be adjusted properly. For details, see "Lens shift range" ( x

page 65).

Moving the lens position to the home position

To move the lens position to the home position, operate in following procedure.

1) Press the <DEFAULT> button on the remote control while the [SHIFT] adjustment screen is displayed.

f The [HOME POSITION] screen is displayed.

LENS

HOME POSITION

ENTER

EXECUTE

MENU

CANCEL

2) Press the <ENTER> button while the [HOME POSITION] screen is displayed (approximately five seconds).

f

[PROGRESS] is displayed in the position.

[HOME POSITION] screen, and the lens position returns to the home

Note f The home position of the lens is used when the lens is replaced or when the projector is stored, and it is not the optical center of the screen.

f The [HOME POSITION] screen can also be displayed by pressing the <LENS/CANCEL> button on the control panel or the <SHIFT> button on the remote control for three seconds or longer.

64 - ENGLISH

Chapter 3   Basic Operations — Projecting

Lens shift range

The projector can adjust the position of the projected image within the lens shift range for each projection lens based on the position of the projected image in the home position (standard projection position).

Following illustration indicates the lens shift range when the projector is installed on desk/floor.

Projection lens Model No.

Standard zoom lens/ET-ELS20/ET-ELW20/

ET-ELT22/ET-ELT23

0.35 H

Projected image width H

0.35 H

0.30 H 0.30 H

ET-ELW22

0.30 H

Projected image width H

0.30 H

0.25 H 0.25 H

Lens shift range

Standard projection position Standard projection position

Note f Use the projection lens in the standard projection position without adjusting the lens shift when the optional Fixed-focus Lens (Model No.:

ET-ELW21) is attached.

Adjusting adjustable feet

Install the projector on a flat surface so that the front of the projector is parallel to the screen surface and the projection screen is rectangular.

If the screen is tilted downward, extend the front adjustable feet so that the projected image becomes rectangular.

The adjustable feet can also be used to adjust the projector to be level when it is tilted in the horizontal direction.

Adjustable feet can be extended by turning them as shown in the figure. Turning them in the opposite direction will return them to the original position.

Maximum adjustable range

Adjustable feet: 23 mm (29/32") each

Attention f Be careful not to block the intake/exhaust vents with your hands or any objects when adjusting the adjustable feet while the light source is on. ( x page 32)

ENGLISH - 65

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents